Search Documents

By Sidney G. Parker, Jack E. Pinnell

Cubic ZnSe crystals have been grown with HCl, HBr, and I, as chemical transport reagents. The growth of large, well faceted crystals is in the order HCl < HBr < I, with some produced by I, transport being 1 cm on an edge. ZnSe:I crystals showed no strain in cross polarized light and were homogeneous as determined by electron microprobe. These ZnSe:I crystals had a mobility at 25°C of about 300 sq cm per v-sec and contained 103 dislocations per sq cm; further, these crystals were pure cubic and showed both photolumi-nescence and photo conductance. Doping was attempted during crystal growth. ZnS and Zn (S,Se) crystals were also grown by I, transport. ZnSe crystals have been grown by most of the common techniques.1"6 Of these, chemical vapor transport as developed by Kaldis2 showed promise of producing high perfection, cubic ZnSe. With chemical transport, crystals can be grown far below the transition temperature for conversion of cubic to hexagonal structure. A small temperature gradient between source and growth region tends to allow near equilibrium growth, which should lead to good crystalline perfection. Because it is necessary to form volatile compounds, halogens or their compounds are extensively used as transport agents. HCl, HBr, and I, were compared as transport agents for growth of ZnSe crystals. Doping during crystal growth was attempted. ZnS and ZnSxSe1-x crystals were also grown by chemical transport. Electrical and optical properties of the crystals were examined. EXPERIMENTAL Fig. 1 is a sketch of the growth apparatus, which was a modification of Kaldis&apos;. A quartz rod which butted against the seed crystal served as a heat sink to promote growth only on the seed. Initially, crystal growth was attempted with ZnSe prepared by wet chemical methods. Because such a material contained oxides and selenates, HC1 reacted with these oxygen compounds to form H2O and no ZnSe transport occurred. Further, this ZnSe contained about 10 ppm Cu plus other impurities. High purity ZnSe, containing small amounts or no oxygen compounds, was prepared by reaction of H2Se with zinc vapors at 600° to 800°C in an atmosphere of palladium diffused H2.7 The ZnSe thus produced was usually copper free and contained only 1 ppm by weight of magnesium as determined by emission spectrographic analysis. G.E.&apos;s electronic grade ZnS, which had about 10 ppm metallic impurities, was used without further treatment. ZnS-ZnSe charges were prepared by mixing the two compounds together, then sintering 24 hr at 1100°C in an H2S ambient. The gases, HBr and HC1, were commercial grade, of 99.9 pct purity, while the I2 was 99.999 pct pure. The single crystal seeds with (111) faces for growth were mechanically held in place by sealing the outer quartz tube to the growth tube. After the charge was introduced, the system was outgassed at l0-5 torr while heated to 500°C. The desired quantities of transport reagents were then sealed off in the system, which had been cooled to 25°C. The growth tubes were inserted into a furnace with the desired temperature and thermal gradient. The system was allowed to cool for 1 to 12 hr from growth temperatures of about 850" to 25°C. The tubes remained stationary during crystal growth. HCl CHEMICAL TRANSPORT GROWTH Preliminary runs with HC1 had a temperature gradient of 100° to 200°C and no seed or heat sink. Only small crystals were obtained in these experiments as

Jan 1, 1970

By F. S. Jr. Norcross

MANGANESE has long been considered one of the United States&apos; most important strategic raw materials. Its indispensabil-ity in steel manufacture makes it vital to the nation&apos;s industrial life. Coupled with this indispensability is the fact that domes-tic producers have not been able as yet to supply more than a small part of the nation&apos;s manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is con-sumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevail-ing prices.

Jan 1, 1940

By F. S. Jr. Norcross

MANGANESE has long been considered one of the United States&apos; most important strategic raw materials. Its indispensabil-ity in steel manufacture makes it vital to the nation&apos;s industrial life. Coupled with this indispensability is the fact that domes-tic producers have not been able as yet to supply more than a small part of the nation&apos;s manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is con-sumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevail-ing prices.

Jan 1, 1940

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By T. B. Massalski, C. S. Barett

THAT metals and alloys of the body-centered-cubic structure tend to become unstable at low temperatures is so nearly universal that any exceptions are worthy of special attention. Studies of the exceptions may disclose unrecognized examples of metastability or may shed light on the nature of some of the factors that stabilize the body-centered-cubic phase. Among the structurally analogous body-centered-cubic 3/2 electron compounds, the ß-phase in the Cu-Zn system deserves further attention for, although this phase is known to undergo partial mar-tensitic transformation on cooling below room temperature to the temperature of liquid nitrogen when the composition is less than about 42 wt pct Zn, it does not transform on cooling .when there is more than this amount of zinc present.1-4 The present authors recently found that an alloy containing 48.35 wt pct Zn could be transformed, however, if deformed severely at room temperature or lower temperatures.V his discovery led to the suggestion that the jerky flow of ß-brass single crystals6 and some of the unusual temperature variations of the yield strength and hardness are due to strain-induced transformation during the tensile tests. The present investigation is an extension of that work to cover the entire available range of compositions of Cu-Zn ß-phase alloys and certain interesting compositions of the ß-phase in the Cu-Zn-Ga system. Particular attention is given to the structure of the transformation product resulting from cold work, which is found to vary with alloy composition, and to the temperature range in which transformation can be induced in the various alloys. The composition limits of the body-centered-cubic phase in the Cu-Zn system, based on a recent review by Raynor7 and the precision determinations of Beck and Smith: are shown in Fig. la; in the ß region the alloys are disordered and in the ß region they are ordered. The rate of ordering is so rapid that a high degree of order is found in any of these alloys immediately after quenching. Experimental The nine binary and four ternary alloys of this investigation were prepared from cathode copper (99.99 pct purity), electrolytic zinc (99.99+ pct), and gallium (99.98+ pct). All alloys were cast in transparent Vycor tubing, homogenized at temperatures between 800° and 890°C, and quenched in water. Ternary alloys were cast in small amounts (-5 g) to predetermined compositions to fall along a line of constant electron concentration in the ternary system. Changes of weight during the casting operation of the ternary alloys were not greater than 1 part in 2500 from the intended nominal weights and therefore their compositions were accepted without chemical analyses. All binary alloys were cast in larger amounts (100 to 150 g), homogenized, and hot rolled after preheating to 800°C. The central portion of the rolled strip of each alloy was annealed for eight days and quenched in brine. All binary alloys were analyzed chemically. The compositions, heat treatments, and metallographic appearances of all alloys are tabulated in Table I. Various samples were subjected to heat treatment or cold work at several temperatures and were then examined metallographically or by means of X-rays. Specimens about 6x6x3 mm in size were examined metallographic ally to confirm the presence of the ß-phase after quenching. Cold work was introduced by fastening each sample between two pieces of steel, cooling the assembly to the desired temperature, and transfering it rapidly to a vise where moderate or severe compression was immediately applied. Cold working at liquid helium temperature was done by a chisel-shaped tool mounted on an X-ray spectrometer, described elsewhere.% A!! metal-

Jan 1, 1958

By P. J. Root, J. E. Warren

An idealized model has been developed for the purpose of studying the characteristic behavior of a permeable medium which contains regions which contribute significantly to the pore volume of the system but contribute negligibly to the flow capacity; e.g., a naturally fractured or vugular reservoir. Unsteady-state flow in this model reservoir has been investigated analytically. The pressure build-up performance has been examined in some detail; and, a technique for analyzing the build-up data to evaluate the desired parameters has been suggested. The use of this approach in the interpretation of field data has been discussed. As a result of this study, the following general conclusions can be drawn: 1. Two parameters are sufficient to characterize the deviation of the behavior of a medium with "double porositym from that of a homogeneously porous medium. 2. These parameters can be evaluated by the proper analysis of pressure build-up data obtained from adequately designed tests. 3. Since the build-up curve associated with this type of porous system is similar to that obtained from a stratified reservoir, an unambiguous interpretation is not possible without additional information. 4. Differencing methods which utilize pressure data from the final stages of a build-up test should be used with extreme caution. INTRODUCTION In order to plan a sound exploitation program or a successful secondary-recovery project, sufficient reliable information concerning the nature of the reservoir-fluid system must be available. Since it is evident that an adequate description of the reservoir rock is necessary if this condition is to be fulfilled, the present investigation was undertaken for the purpose of improving the fluid-flow characterization, based on normally available data, of a particular porous medium. DISCUSSION OF THE PROBLEM For many years it was widely assumed that, for the purpose of making engineering studies, two param- eters were sufficient to describe the single-phase flow properties of a producing formation, i.e., the absolute permeability and the effective porosity. It later became evident that the concept of directional permeability was of more than academic interest; consequently, the degree of permeability anisotropy and the orientation of the principal axes of permeability were accepted as basic parameters governing reservoir performance. 1,2 More recently, 3-6 it was recognized that at least one additional parameter was required to depict the behavior of a porous system containing regions which contributed significantly to the pore volume but contributed negligibly to the flow capacity. Microscopically, these regions could be "dead-end" or "storage" pores or, macroscopi-cally, they could be discrete volumes of low-permeability matrix rock combined with natural fissures in a reservoir. It is obvious that some provision for the inclusion of all the indicated parameters, as well as their spatial variations, must be made if a truly useful, conceptual model of a reservoir is to be developed. A dichotomy of the internal voids of reservoir rocks has been suggested.7,8 These two classes of porosity can be described as follows: a. Primary porosity is intergranular and controlled by deposition and lithification. It is highly interconnected and usually can be correlated with permeability since it is largely dependent on the geometry, size distribution and spatial distribution of the grains. The void systems of sands, sandstones and oolitic limestones are typical of this type. b. Secondary porosity is foramenular and is controlled by fracturing, jointing and/or solution in circulating water although it may be modified by infilling as a result of precipitation. It is not highly interconnected and usually cannot be correlated with permeability. Solution channels or vugular voids developed during weathering or burial in sedimentary basins are indigenous to carbonate rocks such as limestones or dolomites. Joints or fissures which occur in massive, extensive formations composed of shale, siltstone, schist, limestone or dolomite are generally vertical, and they are ascribed to tensional failure during mechanical deformation (the permeability associated with this type of void system is often anisotropic). Shrinkage cracks are the result

By A. L. Lee, M. H. Gonzalez, R. F. Bukacek

Experimental viscosity data for methane are presented for temperatures from 100 to 340F and pressures from 200 to 8,000 psia. A summary is given of the available data for methane, and a comparison is presented for that data common to the experimental range reported in this paper. Correlation of the data is presented, and predicted values are given for temperatures up to 460F and pressures up to 10,000 psia. INTRODUCTION The increasing ranges of temperature and pressure at which fluids are produced, transferred and processed in the petroleum and chemical industries stress the need for accurate information on physical properties, both for engineering calculation and for improving the methods used to estimate physical properties. A survey of the literature reveals that disagreements between published data on the viscosity of methane are common and that most investigations have been conducted over restricted temperature and pressure ranges. This situation made it desirable to undertake an investigation with a scope common to most of the literature data available. APPARATUS AND MATERIALS The apparatus used in this investigation was the capillary tube viscometer&apos;described by Dolan,10 with modifications introduced in the general design and operation of the instrument. It has an effective pressure range from 14.7 to 10,000 psia and a temperature range from room temperature to 400F. The design of the viscometer is based on the establishment of a manometric head between two vessels containing the test fluid and a volume of mercury. The reservoirs are connected by a capillary tube through which the test fluid flows and a tube through which mercury flows. A pressure gradient is established by elevating one of the vessels above the other, the resulting flow of mercury displacing the test fluid through the capillary. The schematic diagram of the system (Fig. 1) shows the arrangement of the equipment auxiliary to the viscometer. The density cells assembly (E, Fig. 1) was not used in this investigation since reliable data are available on methane. 23 The assembly consists of a bank of eight 316 stainless steel pycnometers. Experimental values of the density of a natural gas19 and i-butane14 samples have been obtained for pressures up to 8,000 psia and temperatures up to 340F. The methane used was obtained from the Southern California Gas Co. Mass spectrometric analysis showed a composition of 99.8 percent CH4, 0.1 percent C2H6 and 0.1 percent C3H8. EXPERIMENTAL VALUES AND ACCURACY OF DATA Determinations were carried out at several temperatures. With the temperature in the cabinet controlled at a given level, a series of runs were made at various pressures. To establish pressures lower than that obtained from the methane cylinder, it was necessary to vent the gas slowly to the atmosphere until the desired pressure was reached. The consistency of the test run time for a particular condition can be used as a criterion for the accuracy of the data. A further check is obtained by comparison of the viscosity values obtained using different driving heads. To establish the instrument&apos;s reproducibility, a large number of runs were made at three completely different conditions of temperature and pressure. Data obtained were analyzed statistically to determine the most reliable value for the variance of the experimental data. It was found that the variances of the data taken at different experimental conditions were not statistically equivalent, but they were small. The largest variance was found at 8,000 psia and 100F, where the standard deviation was 0.385 micropoise. Therefore, 99.9 percent of the data can be expected to fall within 1.15 micropoises of the population mean, except for the intervention of systematic errors in operation.

By W. R. Strickler, P. Hazebroek, M. Prats

The pressure and production behavior of a homogeneous cylindrical reservoir producing a single fluid through a centrally located vertical fracture of limited lateral extent was determined by using mathematical methods to solve the appropriate differential equation. It is assumed that there is no pressure drop within the fracture — that is, that the fracture capacity is infinite. It was found that the production-rate decline of such a reservoir is constant (except for very early times) when the flowing bottom-hole pressure remains constant. The production-rate decline increases as the fracture length increases. Thus, the lateral extent of fractures can be determined from the production-rate declines before and after fracturing or from the decline rate after fracturing when the properties of the formation and fluids are known. The production behavior over most of the productive life of such a fractured reservoir can be represented by an equivalent radial-flow reservoir of equal volume. The effective well radius of this equivalent reservoir is equal to one-fourth the total fracture length (within 7 per cent); the outer radius of this equivalent reservoir is very nearly equal (within 3.5 per cent) to that of the drainage radius of the fractured well. The effective well radius of a reservoir producing at semisteady state is also very nearly equal to one-fourth the total fracture length. It thus appears that the behavior of vertically fractured reservoirs can be interpreted in terms of simple radial-flow reservoirs of large wellbore. INTRODUCTION An earlier report1 has considered the effect of a vertical fracture on a reservoir producing an incompressible fluid. That investigation of the fractured reservoir producing an incompressible fluid was started because of its simplicity. Thus, pertinent behavior of fractured reservoirs was obtained at an early date, while experience was being gained of value in the solution of more complicated fracture problems. One of these more complicated problems, and the one discussed in this report, considers the effect of a compressible fluid (instead of incompressible fluids) on the production behavior of a fractured reservoir. In the incompressible-fluid work mentioned, it was shown that the production rate after fracturing could be described exactly by an effective well radius equal to one-fourth the fracture length whenever the pressure drop in the fracture was negligible. Because of the simplification in interpretation, it is a matter of much interest to determine whether the production behavior of reservoirs producing a compressible liquid could be described in terms of an effective well radius which remains essentially constant over the producing life of the field. The details of the mathematical investigation are given in the Appendixes. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable circular cylindrical outer boundary of radius re. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir just described. When gravity effects are neglected, the flow behavior in the reservoir is independent of the vertical position in the oil sand. Thus, the flow behavior in the fractured reservoir is described by the two-dimensional flow behavior in a horizontal cross-section of the reservoir, such as the one shown in Fig. 2. Production is due to the expan-

By H. M. Manasevit, R. L. Nolder, L. A. Moudy

The observation that silicon-on-sapphire crystallo-graphic relationships exist which are unrelated to one another implies that there are regions of sapphire orientations containing these relationships which are separated by boundaries. The presence of these boundaries is demonstrated, initially on rounded cylindrical surfaces md more definitively on flat sapphire substrates with orientations along primary crystallograPhic zones. By means of reflection electron and X-ray diffraction techniques the crystallographic relationships have been studied. Two new relationships have been found, viz., (111) Si (1014) sapphire and (001)Si (1012) sapphire. Also found were multicrystalline relationships. The approximated boundaries between the crystallographic regions for each relationship are shown by means of a stereo-graphic projection. These studies also clarify discrepancies in the literature concerning the silicon-sapphire relationships on the (1120) sapphire substrate. SINCE the first report of the deposition of single-crystal silicon on sapphire in 1963&apos; this epitaxial system has been the object of study by many semiconductor laboratories. In particular, there has been strong interest in the crystallographic relationships between the two materials. In 19652,3 we demonstrated that at least four distinct modes of orientation relationships can occur, namely, (100)Si (0112) sapphire, (111)Si 11 (1124) sapphire, (111)Si (1120) sapphire, and (111)Si (0001) sapphire. Each relationship could be obtained when the substrate plane was at the particular orientation indicated. Other workers as well as our laboratory concurred in general with the initial results. However, two discrepancies were observed. First it was observed by Joyce et a1.4 that on a (1120) substrate a (110) silicon deposit could be obtained. This was actually consistent with the (111)Si (1124) sapphire mode. Second, two other laboratories,5,6 as well as our own,7 have found a deposition on the basal plane which is different than our initial findings. Even though a (111)Si deposit was obtained, the crystallographic relationships were not identical to those previously found. Subsequent work in our laboratories has confirmed that the form found in these later investigations of the basal plane is by far the more predominant, and the original finding was an anomaly. The relationships which have been previously estab1.ished are summarized in Table I. It is seen that at present a rather small number of possible substrate orientations has been investigated. Therefore, it seemed appropriate that a systematic investigation of silicon epitaxy on various sapphire substrate orientations would be of value. It was expected that the answers to three questions could be obtained from such an investigation. These are as follows: 1) Since we know of at least four distinct modes of orientation relationships, over what range of substrate orientation do these modes occur and what is the form of the boundary expected between the different regions in which each mode occurs? 2) Are there other modes which occur on substrate orientations not previously investigated? 3) What is the explanation for the discrepancy between our laboratory&apos;s findings and those results reported by Joyce et al.4 concerning the relationships occurring on (1120) substrates? APPROACHES AND EXPERIMENTAL METHODS Two different approaches were used. Initially, depositions were carried out on rounded cylindrical surfaces which lay perpendicular to the (0112) plane.* By this means the presence of boundaries and their approximate positions could be determined. Finally and more definitively, depositions on flat sapphire substrates with a variety of orientations, mostly along primary crystallographic zones and about the (1120) plane, were studied by means of reflection electron diffraction and X-ray diffraction (using back-reflection Laue patterns and full circle goniometer techniques) in order to determine crystallographic relationships. The sapphire orientations investigated by these means

Jan 1, 1969

Executive Joseph L Gillson, Chairman, J W Woomer, Vice-Chatrman, John S Bell, Walter R Hibbard, Jr. R R McNaughton Finance John P Hammond, Chairman, James C Gray, J S Smart, Jr Investments Gall F Moulton, &apos;63, Chairman, Andrew Fletcher, &apos;62, John M Lovejoy, &apos;61, George I Brigden, ex off as AIME Treasurer, John P Hammond, ex off as Chairman, AIME Finance Committee Award Committees Grouped together at end of list Cooperation with the Canadian Institute of Mining and Metallurgy and the Mining Society of Nova Scotia R R McNaughton, Chairman, C Gerow, Sherwin Kelly

Jan 1, 1960

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951

By P. M. Blair

This paper presents numerical solutions of the equations describing the imbibition of water and the countercurrent flow of oil in porous rocks. The imbibition process is of practical importance in recovering oil from heterogeneous formations and has been studied principally by experimental means. Calculations were made for imbibition of water into both linear and radial systems. Imbibition in the linear systems was allowed to take place through one open, or permeable, face of the porous medium studied. ln the radial system, water was imbibed inward from the outer radius. The effects on rate of imbibition of varying the capillary pressure and relative permeability curves, oil viscosity and the initial water saturation were computed. For each case studied, the rate of water imbibition and the saturation and pressure profiles were calculated as functions of time. The results of these calculations indicate that, for the porous medium studied, the time required to imbibe a fixed volume of water of a certain viscosity is approximately proportional to the square root of the viscosity of the reservoir oil whenever the oil viscosity is greater than the water viscosity. Results are also presented illustrating the effects on rate of imbibition of the other variables studied. INTRODUCTION The process of imbibition, or spontaneous flow of fluids in porous media under the influence of capillary pressure gradients, occurs wherever there exist in permeable rock capillary pressure gradients which are not exactly balanced by opposing pressure gradients (such as those resulting from the influence of gravity). The importance of such capillary movement in the displacement of oil by water or gas was recognized in early investigations and described by Leverett, Lewis and True in 1942.1 Methods advanced by these authors for studying the process using dynamically scaled models were rendered more general and flexible by the research of later workers.2"4 The influence of capillary forces in laboratory water floods has also been discussed by several authors.6 While imbibition plays a very important role in the recovery of oil from normal reservoirs, Brownscombe and Dyes7 pointed out that imbibition might be the dominant displacement process in water flooding reservoirs characterized by drastic variations in permeability, such as in fractured-matrix reservoirs. In water-wet, fractured-matrix reservoirs, water will be imbibed from fractures into the matrix with a countercurrent expulsion of oil into the fractures. If the imbibition occurs at a sufficiently rapid rate, a very successful water flood can result; if the imbibition proceeds slowly the project might not be economically attractive. Scaled-model studies have demonstrated the vital importance of imbibition in secondary recovery in fractured reservoirs. It is therefore important in the evaluation of waterflooding prospects to develop a thorough understanding of the quantitative relationships of the factors which control the rapidity of capillary imbibition. The imbibition process serves reservoir engineers in still another important way by providing a technique for studying the wettability of reservoir core samples. Such experiments are usually conducted by observing the rate of expulsion of oil or water from core samples submerged in the appropriate fluid. Several papers have been &apos;published on the experimental techniques involved?? Although Handy has recently published a method for calculating capillary pressures from experiments with gas-saturated cores, it has not yet been possible to deduce quantitative information regarding water-oil relative permeability and capillary pressure characteristics of the rock from the experimental results. Thus a technique is needed for studying the quantitative dependence of imbibition rate on oil and water viscosity, initial water saturation, relative permeability-saturation, and capillary pressure-saturation relations. The development of such information, including saturation and pressure profiles by laboratory experiments, would be very difficult. However, recent advances in the applica-

Jan 1, 1965

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.&apos; Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

By Mason K. Banks

A process has been developed which produces spodumene concentrates assaying 6.0 pct Li2O and 0.45 pct Fe2O3, with 70 to 75 pct recovery of spodumene. Two flotation separations are required: the simultaneous removal of mica, feldspar, and quartz as a froth product using a cationic collector, and the subsequent removal of iron-bearing minerals as a froth product while spodumene is depressed as a tailing. SINCE the close of World War II there have been numerous developments resulting in the increased use of lithium by industry. Notable among these has been the development of an industrial lubricant, based on lithium stearate, which is fluid at low temperatures, stable at high temperature, and insoluble in water. A new bleaching agent, lithium hypo-chlorite, has also been developed recently.&apos; Other well-known uses are listed below: 1—Lithium oxide in ceramics reduces firing time, lowers melting temperatures, lowers thermal expansion, raises refractive index, and improves chemical resistivity. 2—Lithium carbonate and lithium strontium nitrate are used in pyrotechnics for their brilliant red color.&apos; 3—Lithium chlorides and fluorides are used as fluxes for welding aluminum and magnesium.&apos; 4—The affinity of lithium for nitrogen is the basis for a process used in purifying helium." 5— Lithium chlorides and bromides are used in air conditioning for their powers to absorb organic amines, ammonia, and smoke.6-—Lithium hydride has been used as a source of hydrogen to inflate life rafts and balloons used by the Air Forces and Navy.&apos; 7— Lithium metal and lithium hydride are useful in the atomic energy program in connection with the production of the isotopes of hydrogen." During the 1942-45 period of World War 11, Solvay Process Co. operated a flotation plant with a daily capacity of 300 tons of ore for the production of spodumene concentrate near Kings Mountain, North Carolina. The operation was shut down upon reduction of wartime demand for lithium chemicals, and until recently there has been no production from the Carolinas. In April 1950 an investigation of the problem of spodumene flotation from North Carolina ores was begun at North Carolina State College Minerals Research Laboratory at Asheville, N. C. This laboratory, operating under the combined auspices of North Carolina State College, North Carolina Department of Conservation and Development, and the Tennessee Valley Authority, undertook the spodumene project at the request of Foote Mineral Co. of Philadelphia. The work, involving a period of 15 months of intensive batch and pilot plant investigation, was completed in June 1951 and resulted in development of a process for concentration of spodumene by flotation which has been hereto unrecorded in the literature. A similar approach has been used before on iron, ilmenite, and other minerals, but the literature shows no record of its having been applied to spodumene. Parts of the process are now being used on a commercial scale at the Foote Mineral Co. plant near Kings Mountain, N. C., which has been in production since July 1951. It is the purpose of this paper to describe some of the results of the investigation. The Orebodies Spodumene-bearing pegmatites occur in a narrow belt 24.5 miles long and 1.8 miles wide extending southwestward from Lincolnton to Grover, N. C. According to statements judged to be conservative, the tin-spodumene belt of the Carolinas contains an estimated 4,300,000 tons of pegmatite ore averaging 15 pct spodumene. This amounts to "a reserve of at least 650,000 tons of spodumene (more than 20,000 tons of metallic lithium) to a depth of 100 ft."&apos; This figure includes only bodies having an average thickness of 35 ft and length of 550 ft. There are hundreds of pegmatites in the belt, many of which are less than 10 ft wide. The largest pegmatite in the area has a maximum thickness of 395 ft and maximum length of 3250 ft.&apos; These larger pegmatites are composed principally

Jan 1, 1954

By A. S. Michaels, M. C. Porter, A. Stancell

Previous laboratory studies have demonstrated that the injection of small quantities of reverse wetting agents during water displacement can increase oil recovery from unconsolidated porous media.9 In the present investigation, an attempt has been made to determine more fully the effects of reverse wetting treatments and to clarify the mechanism by which increased oil recovery is effected. Water-oil displacements were performed in beds of 140-200 mesh silica sand. Hexylamine slugs (injected after 0.25 pore volume of water throughput), when adequate in size and concentration, were effective in promoting additional oil recovery. Their effectiveness increased with the quantity of amine injected. However, slugs of sufficient size and concentration to stimulate oil production at water flow rates of 34 ft/day did not do so at 4 ft/day. Visual studies in a glass grid micromodel have shown that the stimulation of oil production, via ayueous hexylamine, is a result of transient changes in the oil wettability of the pore walls. if the amine slug is of sufficient size and concentration to induce significant changes in the adhesion-tension, large continuous oil masses will be formed. if the superficial water velocity is high enough to result in rapid desorption of the amine, a favorable "wettobility gradient" may be established across the masses; under such conditions, high oil mobility is observed, and increased oil recovery results. INTRODUCTION It is generally agreed that the efficiency of oil displacement by water in porous media is limited in part by capillary forces which cause the retention of isolated masses of oil — resulting in the so-called "irreducible minimum oil saturation". Recent estimates10 indicate that there are about 220 billion bbl of petroleum in United States reservoirs which are not economically recoverable with present techniques (such as water flooding). This amounts to almost five times the known recoverable reserves. It has been recognized for some time that a suitable alteration in the water-oil interfacial tension and/or the contact angle, as measured between the water-oil interface and the solid surface, should result in better displacement efficiency. Surface active agents can be used as interfacial tension depressants to accomplish this objective,1,2,7 but unfortunately, the additional oil recovery is seldom commensurate with the treatment cost. In contrast to interfacial tension depressants, the effect of contact angle alterations on water-oil displacements has received relatively little attention in the literature. It is known that the wettability affects the displacement process.3,4,11 Displacements in water-wet systems generally result in lower residual oil saturations than those in oil-wet systems. The effect of "&apos;transient" wettability alterations concurrent with the displacement process have been investigated by Wagner, Leach and coworkers,4,11 wherein it has been demonstrated that the establishment of water-wet conditions during water flooding of oil-wet, oil-saturated porous media is accompanied by significant increase in oil displacement efficiency. Michaels and Timminss studied the effects of transient contact angle alterations resulting from chromatographic transport of reverse wetting agents through unconsolidated sand. It was demonstrated that chromatographic transport of short-chain (C4 through C8) primary aliphatic amines can improve oil recovery and that the recovery increases with the quantity of amine injected (i.e., with either the amine concentration or the volume of the slug injected). Circumstantial evidence indicated that the increased displacement efficiency resulted primarily from transient changes in wettability of the porous medium. In the Present investigation. additional information has been obtained on the effects of reverse wetting treatments and the mechanism by which increased oil recovery is accomplished. Hexylamine slugs of varying size and concentration were chromato-

Jan 1, 1965

By A. M. Gaudin

Activation of sphalerite with silver ions results from the exchange of two Ag ions for one Zn ion in the sphalerite lattice. The exchange is proportional to the logarithm of time and proceeds until either of the reactants is consumed. Sodium cyanide prevents the activation of sphalerite by controlling the ratio [Zn++]/[Ag+]&apos; in solution. If sphalerite has already been activated with excess silver, cyanide ions can deactivate sphalerite provided oxygen is present. SOLUBLE: silver salts are effective activators for flotation of sphalerite with potassium ethyl xan-thate as collector.* Since sphalerite takes up large quantities of silver ions rapidly,2-4 investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hy-drosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Ii&apos;inally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure. The specific surface of two samples from the 65/100-mesh sphalerite stock, measured by krypton gas adsorption," was 420 cm2 per g. Compared with spheres of the same size and specific gravity, the prepared mineral had five times as much surface. Results of a wet chemical analysis and of a spectro-graphic study are given in Table I. Manganese, nickel, tin, indium, thallium, cobalt, and magnesium were not detected spectrographically. All solutions were preparid by -adding reagent-grade chemicals to conductivitv water. which had been previously saturated with the desired gases. Nitrogen and oxygen were purified, but no attempt was made to purify the laboratory air. Radioanalysis was carried out with prepurified Ag110 tracer obtained from the Oak Ridge National Laboratory. The complete decay scheme for Ae is complex. Its primary emissions are 0.09 and 0.55 mev ß rays and 1.48 mev y raysB and its half-life is believed to be 270 days. In preparation of solutions of AgNO3, the amount of Ag110 added was negligible compared to that of the inert silver. Abstraction of silver from solution by sphalerite was measured after agitation of 1.5 g sphalerite with 20 ml of solution in 50-ml pyrex flasks. All sample preparations were carried out in a dry box so that the proper atmosphere could be maintained. After the mineral had been agitated in the silver nitrate solution, an aliquot of the solution and a sample of the wet mineral were transferred to separate counting vials and weighed. The solid sample was dried and re-weighed and the activity in both vials measured by means of a scintillation counter. With scintillation counting it is possible to count y radiation from the solid and liquid, a distinct advantage over the older ß-ray counting techdiques.4 All measurements of silver activity were made using a sodium-iodide well-type scintillation counter. The amount of zinc in solution was measured colorimet-rically by the monocolor method of Sandell.7 Activation Studies Exchange Between Zinc Ions and Silver Ions During Activation: The increase of Zn++ in solution during activation with Ag+ is shown in Table 11. These data indicate a replacement of one Zn++ by two Ag+. Analysis of a separate two-month agitation test indicated that the replacement of Zn++ by Ag+ was, as expected, in the molar ratio of 2.0.

Jan 1, 1958

By T. O. Anderson, E. J. Stahl

Tests to increase knowledge concerning the process of hydraulic fracturing have been performed on three wells in the Allegheny field in western New York. The fracture orientation and its physical appearance at the well-bore was determined by impression packers run at appropriate times throughout the program. Fract~tre azi171uth and its dimensions thus determined were compared to the rock properties and treatment conditions. Logs to provide data concerning rock properties and to improve identification of vertical fractures were run before each step of the fracture treatment. Pressure osc~illu~iot~s were studied after each phase of tile treatments surface pressures during treatment. These measurements show that subsurface pressures exhibit many of the same characteristics as surface pressures during treatment of a well; however, transient pressures are dampened and deelayed in time at the bottom of the well when COmpared with surface pressures. Data obtained from this study provides a means to help locale and determine orientation of vertical fractures made in the open wellbore. Although these rests were performed in only one area, much of the information gained may be applied to fracturing programs in orher areas. INTRODUCTION In this study, various tests were made to provide data to better understand formation fracturing in situ. The reservoir studied is the Richburg oil sand which is a part of a series of predominantly grey sandstones and shales with occasional brown sandstone layers, known as the Caneadea unit of the Canadaway group of Upper Devonian age. Average physical characteristics of 12 cored wells in this area are 13-ft thick gross sand formation, 12-ft thick net sand. 1.7 md permeability, 11 percent porosity, 44 percent oil saturation (before secondary recovery) and 16 percent water saturation (before secondary recovery). This particular area of the Allegheny oil field was originally drilled prior to 1890. The first waterflood secondary recovery attempt was made in 1929. The present sustained waterflood development began in 1951 and is being carried out on a 4.5 to 5-acre spacing. Objectives of these tests were to (I) study fracture azimuth and dimension in relation to rock properties and treating conditions, (2) improve fracture identification techniques, (3) compare surface and subsurface pressure during all phases of treatment and (4) compare the periods of the fluid column oscillations occurring after each phase of treatment. Although the areas of investigation listed appear divergent in purpose, the program was designed primarily to increase knowledge of down-hole conditions leading to rock failure and extension of the fracture thus created. TEST PROCEDURES Wells upon which tests were conducted are designated as Wells 1 through 3. Well 2 was located 440 ft north of Well 1, and Well 3 was located approximately 880 ft west of Well 1. Wells 1 and 2 were completed with cable tools, while the producing interval of Well 3 was rotary cored using fresh water as the drilling fluid to obtain oriented cores. Tests were divided into separate phases on each well as the fracturing program progressed and consisted of measurements performed prior to treatment, during and after the formation breakdown operation. during fracture treatment and after treatment. To verify location and azimuth of the fracture created, and to obtain an impression of wellbore irregularities, a packer was used (Fig. 1). This packer was lowered on tubing into the wellbore opposite the interval under study and inflated in stages to allow the impression material to conform to the wall of the wellbore. A magnetic compass was attached to the tool for orientation reference. Impressions made prior to treatment showed no existing fractures in the wells under study. Impressions made after both formation breakdown and treatment pro-

EVERY forward-looking mining company realizes the need for employing graduate mining engineers so that there will be a supply of qualified men from which to draw for company officers, executives, and mine managers. The mining industry is competing today with numerous other fields of engineering for its supply of technical men, many of which are more attractive than mining because of better pay, living conditions, and well- regulated company training programs. The Ontario Mining Association and the mining companies of Ontario are conducting a postgraduate training plan which if adopted in the United States, might well encourage top quality men to study mining.

Jan 3, 1950

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker&apos;s reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951