Search Documents

By James A. Todd

Use of AN-FO in underground operations has greatly reduced the cost of primary explosives. AN-FO is also less sensitive than conventional dynamites, and when properly used, is safer. Maximum safety in the use of AN-FO, however, requires an understanding of potential hazards from toxic fumes as well as static electricity developed in pneumatic loading. Safe limits and guides have been established to permit most operations to pneumatically load holes that are bottom primed with electric blasting caps, but the toxic fume hazard is less widely understood. During 1959-1960 Du Pont cooperated with the U.S. Bureau of Mines to study the toxic fumes produced by prilled ammonium nitrate-NO. 2 fuel oil mixtures. The conclusions from this work were that oxygen balanced AN-FO, when thoroughly mixed, well primed and well confined in dry holes, produces no greater amounts of toxic fumes than conventional dynamites rated Class I by the Institute of Makers of Explosives. The study also showed, however, that any deviation from these guides tends to increase significantly the quantity of toxic fumes produced. This work was reported by the Bureau of International Symposium on Mining Research at Rolla, Mo., in February 1961.'

Jan 4, 1963

By R. W. Smith, R. W. M. Lai, J. Leja

J. Leja (Professor, Dept. of Mineral Engineering, U.B.C. Vancouver, Canada) — I would like to offer some comments on the behavior of contact angle with time, treated in this paper. The authors should be congratulated for a clear exposition of these uncommon departures in the correlation between flotation and contact angle, in systems of importance to industrial practice. Some nine years ago Professor J. H. Schulman (presently at Columbia University, New York) and I reported on a similar study conducted at the Ernest Oppenheimer Laboratory, Cambridge, England.' The systems used by us had, how- ever, no direct practical application at that time, as mercury in solutions of xanthates was tested with a variety of alkyl-aryl polyoxyethylene frothers which were then new to flotation practice. Further, the paper dealt with findings contrary to the then widely held belief that the contact angle established in collector-solution is unaffected by the addition of a frother. Correlation with flotation, or lack thereof, was not sought, though we did suggest that in many cases the selectivity of frothers might be influenced by the dynamic contact angles. We also stated (on p. 243,

Jan 1, 1968

By Allen H. Rogers

THE need for coordinated effort on public problem by engineers has long been felt. Early in June there will assemble in Washington a conference composed of delegates from all the engineering organizations in the country. The call for this conference is issued by the Joint Conference , Committee of the four national societies as the completion of its work on the organization of a congress composed of delegates representing all the engineering organizations of the United States. The plan for this confederation was presented at a joint meeting of the administrative boards of the national founder societies on Jan. 23, 1920; and was unanimously approved in principle by that meeting. The work of the committee since that date has consisted in drafting a constitution of the organization to be presented at the conference for discussion and, after such amendments as may be adopted, acceptance.

Jan 1, 1920

By PAUL P. ZElGLER

Rapid growth of the aluminum industry continued through 1948 with an acute shortage of the metal in all forms marking the year. Estimates based on shipments made during the first nine months indicate that, in 1948, the industry shipped more than two billion pounds of aluminum products or roughly four times the amount shipped in the greatest peacetime year prior to the war. The rapid expansion of the aluminum industry is particularly reflected in the production of sheet. Last year, the industry as a whole shipped an estimated 40 per cent more sheet than was produced in the peak war year of 1944.

Jan 1, 1949

Discussion of the paper of Frederic P. Dewey, presented at the Cleveland Meeting, October, 1912, and printed in Bulletin -No. 70, October, 1912, pp. 1075 to 1101. EDWARD KELLER, Perth Amboy, N. J. (communication to the Secretary *) :-Mr. Dewey, in his paper, offers a liberal addition of new data to those already to be found in the technical literature on this subject. However, now as before, the work issuing from the U. S. mints and assay-offices conveys the impression that systematic sampling in those institutions is more or less a secondary consideration, the chief attention being given to the principle of producing approximately homogeneous bars; recourse being taken to remelting or refining the bullion. This practice has been definitely rejected in the realm of copper-bullion sampling, for the reason that in such operations there are always unaccounted losses. Does not the same objection hold true for gold-bullions; although, perhaps,in a lesser degree ? Differences of opinion would seem justified on the following statements made by Mr. Dewey: 1. "Only two classes of alloys can form homogeneous bars-those that are solid solutions, and the eutectics."

Jan 3, 1913

Solution mining got back in the news recently when Kalium Chemicals, Ltd., a joint subsidiary of Pittsburgh Plate Glass and Armour & Co. announced its plans to go full speed ahead in mining potash by the solution method in its vast holdings 30 miles west of Regina, Saskatchewan. The company is keeping the technical details of this mining technique under wraps for competitive reasons, but company officials insist that the major difficulties in solution mining of potash have been overcome and that the final product will have definite competitive advantages on the open market. Kalium's holdings in the Regina area total about 500 sq mi. The ore-primarily sylvite mixed with appreciable quantities of halite-occurs in the Prairie Evaporite formation at a depth of 5300 ft. The ore zone averages about 100 ft in thickness. Too deep to be economically mined by conventional underground methods, such as is being done at International Minerals & Chemical Corp.'s Esterhazy mine (depth about 3100 ft), Kalium gambled that it could develop a successful method of solution mining even though earlier attempts in Germany, the U.S., and Canada had failed.

Jan 6, 1964

By William McCullouch

The method of determining moisture percentages in coal has been defined as purely empirical. The procedure, as defined, has been published in the U.S. Bureau of Lanes technical papers and approved by the American Society of Testing Materials but deviations from this established procedure are common in most commercial and private laboratories. It is not within the scope of this paper to discuss the deviations in common practice but rather to give a detailed account of the method in use in the laboratories of the United Electric Coal Companies. In general, moisture values are presented as surface moisture and, for lack of a better term, inherent moisture. The formula for adding them together to give total moisture is common knowledge. In practice, on high-moisture bituminous coal, it has been found that the line of demarcation between surface and inherent moisture is very indefinite, the inherent moisture being so loosely held that it is released far beyond its natural limits when the prescribed method of the A.S.T.M. for determination of surface moisture is followed. This is shown in Table 1 for two typical washed coals from Illinois.

Jan 1, 1938

By W. H. Wamsley

Used in combination with conveyor belt haulage, bucket wheel excavators offer unusual possibilities for low excavation and haulage costs. Originating in Germany, these machines are now in use or on order for Australia, Northern Rhodesia, the Belgian Congo, Italy, Yugoslavia, France, Belgium, Indonesia, and the Union of South Africa. A diamond mine in South Africa that has been using German bucket wheel excavators since 1928 purchased American cable-way excavators and American scraping equipment after the war. Operating cost for this equipment was double that for the bucket wheel machines operating in the same mines with crawler-mounted stackers. Machines built and operated in the U. S. are, as far as the writer knows, confined to the northern Illinois coal field, where they are used in conjunction with large shovels to strip overburden too high to be reached by the 30 to 40-yd shovels. Their long stacker belts can deposit the spoil far enough behind the coal face to avoid slides, in such a manner as to make reclaiming the land easier. These large, specialized machines are now being made by Bucyrus-Erie Co. but are not adaptable to many open pit mining situations.

Dec 1, 1956

By John F. Shaw

The Denver Mining Research Center headquartered at Denver, Colo., is typical of the new research units recently activated as a result of increased emphasis by the U. S. Bureau of Mines on research concerned with metal and nonmetal (except mineral fuels) ore extraction. The Denver Center, together with the recently established Minneapolis Research Center and the Offices of Mining Research at Reno and Spokane, and the older, well-known Applied Physics Research Laboratory at College Park, Md., share the responsibility for the comprehensive mining research program. The Denver Center specializes in two areas of research: (1) The development of engineering principles and mathematical techniques applicable to exploration, development and operational problems in mining, and (2) the study of rock mechanics as applied to ground control. The first area presently includes three categories: research on methods of ore sampling, mine-systems analysis, and applications of statistics to problems of mineral exploration. The second area emphasizes research in two main categories: laboratory investigations designed to develop a fuller understanding of how rock be- haves under the loads imposed by mining, and field investigations to evaluate stress-strength relation- ships in full-scale, operating mines.

Jan 3, 1962

By H. I. Smith

The technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe there is accord, I will distinguish between booster and auxiliary fans. Definition of Booster and Auxiliary Fans In discussing underground fans G. S. Rice1 distinguishes between those used to increase the amount of air passing a given point and those used to augment the ventilation locally. He describes a booster fan as one which is installed to handle the entire air current passing a given

Jan 1, 1927

By Arthur E. Granger

IN the early days of the science, and until the recent past, geologists worked as individuals or in small groups. Prior to 1930 perhaps the largest single group under one administrative head was the Geologic Branch (now Division) of the U. S. Geological Survey, which employed at that time (including temporary help) 100 to 150 geologists. Today that same unit employs some 1500. In industry some companies employ as many as 100 geologists in a single department. These numbers obviously pose a need for administration. The basic qualifications for good administration are the same for any group of human beings, but the administration of geologists presents some special problems. Choosing Administrative Personnel: There are two kinds of personnel needs: 1) technical, which requires professional geologists who have proved their capabilities in the field, and 2) clerical and fiscal, which provide the necessary supporting or housekeeping functions. This discussion will be concerned only with the first category, except to point out the need for competent and understanding help from clerical and fiscal people and close relationship between top administration, technical or professional personnel, and the clerical and fiscal groups.

Jan 7, 1957

By Allan B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drill- holes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 ¼ -in. diam, on 25-ft and 100- ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals.

Jan 7, 1959

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By A. G. Guy, T. B. Lindemer

A second intepation of the Fick law has been developed and applied to three-place data generated from the Gosting and Fujita solution of the diffusion equation. This integration provides new mathematical techniques for the analysis of experimental data. Through use of the synthetic data it is shown that for concentration-independent interdifiusion coefficients these techniques permit a more accurate determination of the coefficients than does the usual Boltzmann-Alatano analysis. Another technique, applicable to the most general concentration-dependent diffusion coefficients , can be used to determine whether given sets of coefficients are consistent with the experimental ternary concentration-distance curves. DURING the past 10 years the subject of three-component diffusion has advanced from the stage of a laboratory curiosity to the status of an accepted portion of physical metallurgy.1 In the course of this development the underlying treatment for two-component sys- tems was extended and generalized to accommodate the added component, but fundamentally the analyses currently employed for ternary systems are analogous to those previously developed for binary systems. There are several indications that an improved analysis is needed for the ternary case. First, the two cross coefficients, D312 and D321 are typically an order of magnitude smaller than the direct coefficients and consequently are difficult to determine with adequate precision. Second, instead of a single concentration-penetration curve (as in binary diffusion), there are four such curves in the usual determination of ternary diffusion coefficients. These curves have definite theoretical interrelationships, but actual experimental curves exhibit significant departures from these relationships. Finally, the amount of data needed to adequately describe the diffusion behavior of a ternary system is so large that radically new methods are needed to facilitate the gathering of these data. ICirkaldy2j4 has proposed several possible analyses of ternary diffusion data, including some of the methods in current use. A "second-integration" procedure proposed by him4 differed in important respects from that presented here and was not carried to the point of application. Two other methods have been explored by the authors and will be published separately; these are a numerical analysis technique and a method for the analysis of a single ternary diffusion couple. Still other analyses are being explored by various investigators. At present it seems likely that the final analysis of ternary diffusion that evolves will be a composite

Jan 1, 1968

By W. M. Weidel

While electric lamps both of the cap and hand type are being introduced into many mines requiring the use of safety lamps, the oil-burning safety lamp is still used in the great majority of cases, and even where the former are used the latter must continue to be employed when testing for gas. It is not the intention to discuss here the relative merits of the two types, but simply to give a comparison of the illuminating effect or candlepower of several kinds of ordinary safety lamps used for general work and for testing. Few data have been published in recent years on this subject and because of this it is hoped that the following information may be of some interest and value. The lamps tested were in all cases of standard size and in good condition, all practically new, and were selected from a collection of about 100 with a view to obtaining results on as many different common types as possible. With the exception of the gasoline-burning lamps, five different oils were used in each lamp to determine whether particular oils were suited to particular lamps and whether there was any great difference in the illuminating power of the different oils, or whether some oils would maintain their illuminating power better than others throughout a working period of 8 hr. No attempt was made to determine the amount or cost of oil burned by each lamp, but the condition of the lamp, wick, glass, and gauzes was noted after each test. Description of Apparatus Used The candlepowcr was determined with a Weber photometer, Fig. 1, which consists of a tube A containing a movable milk-glass screen adjustable by the milled screw B. The distance of this screen from the standard light at C is read on the scale attached to A. The standard light consists of a benzine lamp so arranged that the height of the flame may be adjusted exactly by observing it against a scale in the lamp box through an opening in the front. The lamp to be tested is placed at D so as to illuminate a milk-glass screen in the holdcr at E. At the intersection of the axes of tube A and sight-tube F are placed two 45' prisms with their surfaces in contact so that the light from D may pass through with-

Jan 1, 1917

By R. F. Mehl, W. Batz, C. Wells

Diffusion coefficient values for carbon in austenite covering a wide range of temperature and composition have been determined employing statistical methods. In addition, the relation between concentration and each of the following, D (diffusion coefficient), Q (activation heat of diffusion), and A (the constant in the diffusion equation), has been obtained. A study of the rates of diffusion of austenite was published in Metals Technology in 1940.' The present investigation is an extension of the earlier work, undertaken (1) to obtain values of the coefficient of diffusion, D, over a much wider range of carbon concentration, and (2) to provide data in all ranges of concentration and temperature in such abundance that statistical methods could be employed to evaluate the accuracy of the data with unusual precision. Composition of Materials: Composition of materials used in this research program are listed in table I. These materials, all forged to about 1 1/4 in. rounds, consist of a high-purity iron, Armco iron, a large number of laboratory-made plain carbon steels containing amounts of impurities normally expected in high-quality commercial steels, and three silicon steels. Since it was known at the time these steels were being made that impurities in the amounts present were unlikely to affect carbon diffusion rates' significantly, the effort made to obtain high-purity steels was not as persistent as it otherwise would have been. Procedure: In general, the procedure followed by Wells and Mehl and described' in detail in an earlier publication' is the one used by the present authors. However, certain modifications have been made which it is believed allow diffusion data to be interpreted more objectively and correctly. These are described completely under appropriate subheadings which follow. Experimental Procedure: Experimental procedure includes (1) the preparation of specimens by welding steels of different carbon contents, (2) the heating of these for certain times at selected temperatures in order to diffuse carbon along the specimens across the welded "interface," and (3) the determination of the carbon distribution across the diffusion zone. Preparation of Specimens: Prior to welding steel of one carbon content to iron or steel of another carbon content, surfaces to be welded are machined perpendicular to the longitudinal axis of cylinders which are about 3/4 in. in diam and 1 1/2 in. long. The prepared, flat, parallel surfaces are brought together and butt-welded electrically. Evidence of a good weld is given in fig. 1. Welding temperature

Jan 1, 1951

By JOSEPH MACDONALD

STRIPPED of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it, and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If be fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be divided into a number of main departments, which are subdivided into minor departments. Each main department should be under the immediate charge of a superintendent, or a foreman, and each minor department under a shift-boss. Organized in this way, and with all the principal centers of activity connected by telephone, the manager can keep in touch at all times with the details of every branch of the business, and be in a position to perform effectively the full duty of manager. The ?total cost of mining operations may be broadly divided under the heads of Labor, Supplies, and Marketing. Of these, it will be found, on averaging a number of cases, that the cost of labor will be about two-thirds of the total cost. The importance, therefore, of an efficient labor-department will be apparent. This department must be sub-divided and organized differently, according to the peculiar conditions at each mine, and no one system, however well suited for one particu-

Jan 1, 1909

By Lewis A. Riley

I desire to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomerates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideratiotl in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945