Search Documents

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors' paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.'' The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors' 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)' D = 3.55 x 10"3 exp (-5550/)' D = 4.3 x 10"3 exp (-5620/1')' Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By J. D. Doherty

A. R. POWELL*—Mr. Doherty has outlined in a most thorough manner valid arguments for the development of an industry in this country making syn. thetic liquid fuels from coal. No thoughtful person will dispute the statement that it is essential to carry on fundamental and applied research and acquire engineering "know-how" by the erection and operation of two or three large plants in the near future. Considerations of national security indicate that this should be done, irrespective of any temporary present surplus of natural petroleum. It is the belief of the discusser and of many others interested in coal technology that our energy picture of the future will include an increasing utilization of coal directly, without any conversion to liquid fuel, as a source of energy. A fact that is sometimes forgotten is that petroleum fuels have often been cheaper than coal in many locations and over long periods of time, and this price factor has been of great importance in expanding the use of petroleum fuels at the expense of coal. Synthetic liquid fuel made from coal must necessarily be several times as costly as the coal from which it is made, and this fact alone will have a profound effect on the future energy pattern of our country. This complete change in the economic relationship between solid and liquid fuels will lead to the substitution of coal itself for many uses now supplied by the relatively cheap petroleum fuels. From the standpoint of conservation of our natural resources, the substitution of coal itself for liquid fuels wherever possible when the age of synthetic liquid fuel arrives is also logical. At least 50 pct of the energy of coal is lost during conversion to liquid fuel. Nor is this com-pensated for by a higher utilization effi-ciency of the liquid fuel in most cases. For example, modern steam-boiler plants can operate at equal fuel efficiencies with either coal or fuel oil.

Jan 1, 1950

By Robert G. Nisle

In conducting a pressure build-up test on an oil well, it is often necessary to shut-in the well for a short time prior to initiation of the test. The effect of such a short tern shut-in on the resulting pressure build-up curve is derived. The derivation is based on the Kelvin point-source solution and is a straight forward extension of the fundarnental theory. The magnitude of the effect is evaluatecl and illustrated by an example. It is shown that if the production subsequent to the short term shut-in is at least 10 times the duration of the shrct-in, the effect will he less than 10 per cent. INTRODUCTION It often happens that before a pressure build-up test can be made an additional valve must be mounted on the wellhead, or on arrival at the well, it might be learned that the well had been shut-in several hours the previous day because of a shortage of tankage. In such cases the question is How will such an interruption of production affect the results of a pressure buildup test This work explains how to take account of such a short term shut-in in order that the test can proceed without further delay. The solution presented here makes use of the Kelvin point-source solution used by Horne1 in his treatment of the pressure build-up in wells. Use is also made of the super-position theorem. MATHEMATICAL DERIVATION The well is assumed to have been in production at a constant rate for a relatively long time (several days or more). It is then shut-in for a short time, after which it is again placed in production at the previous constant rate. It continues to produce at this rate until shut-in for a pressure build-up test. The Kelvin point-source solution is expressed by Eq. 1. The sequence of production rates is listed in Table I. TABLE 1 — SEQUENCE OF PRODUCTION RATES Time interval Production Rate At time AT the pressure will be the resultant of the sequence of production rates shown in Table 1. An expression for the super-posed effects may be derived from this table. (Effect of + q for T + ? T) + (Effect of - q for T + ?T-t,) + (Effect of + q for T + ? T - t,) + (Effect of - q for ? T) = Resultant........(2) The desired result is obtained by substituting the effect defined by Eq. 1 for the terms in Eq. 2. The result is Eq. 3. When the logarithmic approximation is made for the exponential integrals and the terms collected the result is Eq. 4. Let T — t2 = T = flowing time following short term shut-in t2 — t1 = 6 = duration of short term shut-in Then T - t1 = r + 6 Substitution of these quantities in Eq. 4 gives p(rw ?T) = P,, -When d<<t - AT then d—&apos;-, T— approaches 1. r + AT In this case the effect of the short term shut-in may be ignored. In order to get some idea of the numerical magnitudes involved take the worst possible case, when AT = 0, that is at shut-in. If the error is made less than some maximum acceptable value at this time, it will be less than the maximum for all subsequent times. d + r Let the difference between the value of y-— and 1 be less than 0.1. Then —6+r — 1 < 0.1 S < O.l T Therefore, if the flowing time following a short term shut-in is at least 10 times the duration of the short term shut-in, the error introduced by ignoring the short term shut-in will not exceed 10 per cent of T+AT A T

Jan 1, 1957

By T. A. Dungan

The thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbo-thermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was&apos; expected to obtain metallic magnesium. The results were positive and metallic magnesium was .0

Jan 1, 1944

By William Alden

A GREAT landslide occurred on June 23, 1925, in the valley of Gros Ventre River, about 35 miles south of Yellowstone National Park (Fig. 1). The relations of the north-easterly dipping rock formations of the slide scarp and of the dam formed by the slide are shown in the diagrammatic cross-section of the valley (Fig. 2). This generalized section is based on unpublished maps and notes by Eliot Blackwelder, in the files of the U. S. Geological Survey. FIG. 1.-MAP SHOWING SCARP AND DAM (LARGE DOTS) AND LAKE (CROSS-LINED) FORMED BY LANDSLIDE BLOCKING GROS VENTRE RIVER. (Scale 1, in. = 1 mile; contour interval 100 ft. From Grand Teton and Mt. Leidy topographic maps). Heavy rains and melting snow in the Gros Ventre Mountains had saturated clay layers in the Carboniferous strata, which dip toward the valley at angles of 18° to 21°, consequently an enormous mass of rock at the end of the north spur of Sheep Mountain became loosened and, on the afternoon of June 23, slid suddenly down into the valley. Within a few minutes this mass of debris-estimated as 50,000,000 cu. yd.-carrying

Jan 1, 1928

By D. J. Jr. McAdam

PART I. OUTLINE OF INVESTIGATION, DESCRIPTION OF MATERIAL AND METHODS RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water.

Jan 1, 1928

By J. C. Donnell, O&apos

Sinking an inclined ventilation shaft at the Never Sweat mine of The Anaconda Co. has required a unique underground hoisting arrangement because the shaft changes direction from vertical to 71.5º. Access to the project is made through the High Ore shaft to the 2800-ft level, then by crosscut to the bottom of the vertical Never Sweat shaft. The 71.5º incline shaft starts at this point, which makes an unusual operation as the 60-cu ft sinking skip coming up the incline changes into a vertical position above the 2800-ft level before going into the dump scrolls. This requires both rollers and guide shoes on the skip. Coming up the incline to the collar of the shaft the loaded skip enters into a guard before reaching the vertical section. The tendency of the surface- mounted Never Sweat hoist is to lift the front wheels of the skip off the track, so the guard keeps the skip on the rails during the transition.

Jan 11, 1965

By K. C. Li

TITANIUM, because of its high strength, weight ratio, and high melting point, became the metal of the jet age. Zirconium, because of its low neutron cross section and high corrosion resistance to hot water, became an integral part of the nuclear era. Since both metals are very similar chemically, more or less the same process is used for their production. The sudden rise of this new industry of titanium and zirconium seems to have caused some uncertainty as to the future development of processes for making these metals. Although zirconium was discovered in 1789 and titanium in 1790, it was not until 1945, six years after W. J. Kroll patented his process, that F, S. Wartman of the U. S. Bureau of Mines perfected the technique of producing ductile titanium, and it was not until 1946 that Kroll perfected the technique of producing ductile zirconium in commercial quantities. Since then the Government and private industry have spent millions of dollars each year constantly searching for new methods, with the hope that some day titanium can be produced as economically as aluminum and magnesium or as cheaply as stainless steel.

Jan 11, 1957

By Robert B. Hoy

To maintain a competitive position in the world market in spite of higher domestic labor costs, the U.S. has been forced to the forefront in developing labor saving devices. This has resulted in automation in our factories, mechanization in our mines, and development of faster and more economical methods of transportation. Since World War II the domestic mining industry has suffered perhaps more than any other sector of our economy. When we assisted our allies-and our enemies-to get back on their feet following the ravages of war we were perhaps overly generous in providing funds and technical assistance to develop foreign mining industries that have since become thorns in the side of our own industry. It has become imperative that domestic industry exert its vigor to meet the challenge of foreign competition. While the domestic industry can meet this challenge of foreign competition in part by protective tariffs, quotas and governmental aid, the most effective way is to maintain technological superiority that will reduce manpower requirements and costs and increase productivity. There is this opportunity both in mineral processing and in mining.

Jan 9, 1962

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average. $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped udder the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton., Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand Mines Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all feeding into the same system.

Jan 2, 1916

By Reynold Q. Shotts

Chemical methods, based on the relative rates of oxidation of fusain, bright coal, and dull coal by nitric acid, have been devised to determine these coal components.1-4 Results obtained by oxidation methods for fusain have been checked against results obtained from microscopic methods on duplicate samples of the same coals, but to the author&apos;s knowledge this has not been done for bright and dull coal components. For this reason it is not certain that the two methods of analysis identify essentially the same chemical or physical units. It would be highly desirable to see results of the application of both methods to duplicate samples, but in the absence of any such data the author has attacked the problem indirectly. From the U. S. Bureau of Mines samples were obtained of three Alabama coals which the USBM had analyzed optically and reported on over the past 30 years. These samples were subjected to analyses by oxidation rate methods. Results of this work, and comparisons with the USBM analyses, have been published. This was the first indirect approach to the problem. The present report attempts a second indirect approach by way of internal validation.

Jun 1, 1955

By Edward Sampson, Allan B. Griggs

SURVEYING of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 ft. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 ft. One hole was found to be deflected 70° at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone"&apos; in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes.

Jan 1, 1946

By John L. Burnett

Manufacture of lightweight concrete aggregate from common shale is one of the most rapidly growing industries in the field of nonmetallic or industrial minerals. Although expanded shale" has been in use since it was developed by Stephen J. Hayde in 1917, it was not until after World War II that it became a substantial competitor with other aggregates. There are some 70 plants now producing this aggregate in the United States, approximately half of them in states west of the Mississippi River. Expanding plants throughout the U. S. are grouped around major urban centers such as Los Angeles, New York, Chicago, and Denver. Concrete made with expanded shale aggregate combines the desirable features of low weight with relatively high strength, making it especially useful in concrete block, in structural concrete for multi-story buildings and in a variety of specialized concrete products such as prestressed panels and beams, and storage tanks. As the cost of construction continues to rise, lightweight concrete will probably be used in increasing quantities because of its low cost relative to the more traditional construction materials such as wood, brick and steel

Jan 1, 1964

By James L. Sweeney

The Project Independence Evaluation System (PIES) is a complex evaluation, forecasting, and analysis system which represents the U.S. energy production, conversion, transportation and consumption activities. The system includes various models: An econometrically estimated energy demand model, used to evaluate the final demand functions for energy commodities ; A collection of supply models, used to evaluate the cost curves or supply curves for domestic crude oil, natural gas, coal ; An integrating model used to describe energy conversion and transportation activities and to calculate prices which equate energy supply and demand in each market. PIES has been used to generate conditional forecasts of the 1980, 1985, and 1990 states of the energy system--forecasts conditional upon the world oil prices, the energy policy environment, and other uncertainties. Scenarios have been structured to separately examine conservation initiatives, domestic energy supply enhancements, an extensive electrification strategy, and oil and natural gas well -head price regulation. This paper presents the basic model, discusses its use for examining policy options, and describes several forecast results. The paper draws heavily upon work completed for the 1976 National Energy Outlook, published by the Federal Energy Administration.

Jan 1, 1977

By E. A. Stevens

IT has been ascertained in recent years that certain rocktypes, geological formations and structural conditions may be used as fairly reliable guides, when prospecting in recognized mineral belts or mining districts, with a reasonable certainty of discovering "pay-ore;" and that such is considered as a practically established conclusion may be inferred from a perusal of the recent reports of the U. S. Geological Survey and the literature of the several scientific societies discussing minim, geology, and kindred subjects. Cripple Creek is no exception to this conclusion, and the rock-type or association, rather than the structural condition, is the most infallible guide.† These guides consist of four, possibly five, dike-rocks, three of which are extremely basic, while the fourth is an acid rock of an entirely dissimilar character. The basic rocks are nepheline-basalt, limburgite, feldspar-basalt and tephrite. There are grounds, however, for believing that the two latter are subdivisions of one type, and therefore will be described under one head. The acid rock is quartz-porphyry. Nepheline-basalt is-a rock encountered in but few localities elsewhere on this continent, and occurs in narrow dikes cutting various formations. When typical‡ it is composed of

Jan 1, 1913

By R. W. Bond

The gas-lift is a comparatively recent development in the Oklahoma and Kansas fields. It was used to some extent in the old Dilworth field several years ago, but the first extensive installations were made in the Tonkawa and Garber fields in Oklahoma early in the year 1926. Compressor Equipment During the early development of the system, the equipment used generally consisted of small tandem compressors of about 250 cu. ft. per min. displacement, driven by automotive-type gas engines, using a short belt drive. These compressors were first installed at the individual wells largely as an experiment. After the experimental installations had proved the method a success, it was considered economically advisable to centralize the compressor equipment in strategically located stations. However, as the information in regard to "gas-lift flowing life" was anything but definite, and the most optimistic estimates in regard to it did not exceed six months, portability of equipment was still the first consideration in the minds of many operators, who continued to install srnall semi-portable com-pressors in their centralized stations. As electric power became available in the fields, the electric motor came rapidly into use as the prime mover for the small compressors. The operating cost of this motor is greater than that of the automotive-type gas engine for the same power output, but the greater continuity of service tends to balance the extra cost. Aside from the semi-portable units, a number of strictly portable compressors were used. These consisted of automotive-type gas engines direct connected to vertical compressors. The unit was assembled on one base and could be mounted on wheels or skids as desired. The chief objection to these, in the writer&apos;s opinion, was their small capacity— approximately 150 cu, ft. per min.—which made it necessary to use two, three, and sometimes more units per well, thus making the installation rather costly. However, they have been found valuable for test purposes and emergencies, where installation time is an important factor.

Jan 1, 1928

By John D. Morgan

Prior to World War I there was no Government stockpiling program. Prior to World War I1 relatively few items were included in Government stockpiling and the start of that war found most objectives for even these few materials far from complete. Profiting from the experience of materials shortages in two wars, Congress in 1946 passed the Strategic and Critical Materials Stock Piling Act, which stated that it is the policy to decrease and prevent wherever possible a dangerous and costly dependence of the U. S. upon foreign nations for supplies of strategic and critical materials in times of national emergency. However, as of mid-1950 few stockpile objectives had been achieved. Shortly after the start of the Korean War it was obvious that in the absence of adequate stockpiles, the defense program could not be successfully carried out without broad authority to expand supplies of strategic and critical metals and minerals and at the same time to channel limited supplies of these materials to essential defense purposes. Accordingly, in September 1950 Congress passed the Defense Production Act, which provided broad powers for allocating materials and for making arrangements, including financial, to expand supplies.

Nov 1, 1955

By H. N. Herrick

THE flow characteristics of drilling muds, as described in this paper, and the method given for solving problems relating to the flow of these muds through pipe and accessory equipment, are based on a conception that drilling muds are plastic solids like paints or greases; not liquids. The data presented in this report have been obtained from studies of California muds, chiefly those used in the Kettleman Hills field, by the Producing Department of the Standard Oil Company of California. Although no claim of scientific exactness is made for the formulas and diagrams, since the data upon which they are based, are not. complete even for California muds, the method has proved to be a convenient means for estimating, closely enough for practical purposes, the pressures required to force muds at various rates through pipe systems in which they are handled. Certain approximations have been made to simplify the procedures so that they can be used easily in the field.

Jan 1, 1932