Search Documents

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman's2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman's method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman's2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By Samuel Storchheim

IT was noted that variations existed in the magnetic properties, namely, coercive force, He, and rema-nence, Br, of 18/8 stainless steel wires of the same analysis when these wires were given the same percentage of reductiori of area at different rates of reduction. In order to determine the extent of these variations, a program was initiated whereby commercial 302 and 304 stainless steels were drawn with a wide variation of speeds. Ultimate tensile strengths and specific resistances, as well as the Hc-BT measurements, were determined. If variations of considerable magnitude were found, it was thought that the knowledge accrued from the investigation could probably aid in determining the particular drawing speed required to obtain desired properties for a given specification for a particular analysis of wire. Drawing Procedure Two specimens (set I, No. 302 and No. 304), the chemical analyses of which are given in Table I, were drawn at different speeds, namely, 45 to 3900 ft per min, directly from 0.016 in. diam wire to 0.004 in. diam wire, a 93.7 pct reduction of area. To obtain this high percentage of reduction, the wire at 0.016 in. was softened by annealing at 1150°C. It was then strung in a No. 16CF variable speed Vaughn drawing unit and passed through 13 B.&S. gage dies of successively smaller diameter, as shown in the accompanying table. Following this step, several hundred feet of the wire was drawn, at a particular speed, through the dies and wound upon a spool. Once the sample of wire was drawn at the desired speed, the spool with the finished sample was removed, tagged for later identification, and an empty spool was placed in the machine. Another wire sample was drawn at a different speed, after making the necessary adjustments upon the Vaughn unit. At the greater speeds, several thousand feet of sample were drawn to insure that the wire to be used for testing would be uniform. This was done because the desired speed was not reached instantly; the wire taking a short while to attain the required drawing rate. All speed measurements were made by placing a tachometer against one of the machine's pulleys during the actual drawing of the specimens. 84.4 pct reduction of area. The 0.072 in. diameter wire was also annealed at 1150°C. The process of obtaining samples was the same as described above. The only difference between the two was that the rates involved were not as extensive, set II covering a range of 625 to 1150 ft per min. Tensile tests were carried out for the 0.004 in. diam wires on a horizontal Scott Tensile Tester, while tensile tests for the 0.028 in. diam wires were made on a vertical Scott Tensile Tester. Each value listed in the tables represented the average of five samples with a maximum deviation of approximately 3 pct among the samples. Resistance per foot of the wires was determined by use of standard bridges accurate to the nearest hundreth of an ohm for the 0.004 in. wire, and to the nearest thousandth of an ohm for the 0.028 in. wire. The resistances per foot were then converted to resistivities by use of the following equation: P = RxCM where R is the resistance per ft in ohms per ft; CM, the area in circular mils; and P, the resistivity in ohms—CM. The values listed in the tables likewise

Jan 1, 1952

By S. C. Sun

With the aid of emulsifiers, intense high-frequency sound waves are capable of emulsifying any collector in water. The data show also that ultrasonically emulsified collectors are more effective in floating minerals than the nonemulsified collectors. THE use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and OstrawskyV escribed the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanaka3 employed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets In the other. The dispersed liquld is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses, 5a, B proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft 7, 8 deduced that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids. This film has two interfacial tensions, one with the water and the other with the oil, which are not necessarily equal. The difference in interfacial tension between the two surfaces of the film is chiefly responsible for forming different types of emulsions. For example, if the interfacial tension between water and film is less than that between oil and film, the film will become convex on the water side, thereby tending to form an oil-in-water emulsion. On the other hand, if the interfacial tension between water and film is greater than that between oil and film, the film will become concave on the water side, thereby tending to make a water-in-oil emulsion. In line with this theory, emulsifying agents soluble in water have the tendency to form oil-in-water emulsions, while those soluble in oil form emulsions of the reverse type. Apparatus and Experimental Procedure: The ultrasonic apparatus shown in Fig. 1 consisted of a hypersonic generator (A), Brush Development Co. model Bu-204; a hypersonic transducer bowl (B) whose resonant frequency is 400 kc per sec; and a round-bottomed glass tube (C) of 2.2 cm ID and 21 cm in length. The acoustical output power of the hypersonic transducer bowl was standardized with a Hewlett Packard vacuum tube voltmeter, model 41 0B, across the hypersonic generator output. The glass tube, containing the materials to be emulsified, was placed 1 cm above the central surface of the transducer bowl, which was filled with water as shown in Fig. 2. Ultrasonic emulsification was performed in three steps, although a one-step method has been used: 1) emulsifying the predetermined amounts of col-

Jan 1, 1956

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By C. Feng

HE sensitivity of twinning in molybdenum alloys containing 20 or more at. pct Re was reported by Dickenson and Richardson&apos; and Sims et a1.&apos; The latter3 also studied the effect of twinning on plastic deformation of these alloys. Recently, in this laboratory, the twinning planes in a series of Mo-Re alloys were successfully identified by tracing their boundaries on two known surfaces of the crystals, with the aid of stereographic projection. The nominal alloy composition and the results of the determination are listed in Table I. Metallic powders of molybdenum and rhenium with 99.9 pct purity were mixed, pressed and arc-melted into buttons under purified argon in a water-cooled copper hearth; the buttons were annealed at 2400 °C in vacuum (10-&apos;mm Hg) for 1 hr, remelted under argon and finally reannealed in vacuum at 2400°C for another hour. This treatment yielded a homogeneous alloy. Large-grain specimens devoid of subgrains were obtained with grain diameter varying from 1/8 to 1/2 in. A typical specimen weighed about 15 g. Orientations were determined by taking X-ray back reflection photographs for each grain on a polished surface of the specimens. Two surfaces were cut and polished; the angle between the two surfaces was measured with an accuracy of *2o. The twins were produced by compression in a hydraulic press at room temperature. Usually, several sets of twins could be obtained within each grain. Except in cases where no twins were formed, (Crystals 7, 8, and 9) the twinning planes were identified consistently as the (112) family over a wide range of alloying compositions and surface orientations of the crystals, as indicated in the stereo-graphic triangle in Fig. 1. The twins, however, were not broad enough to accommodate a conventional X-ray beam and no identification could be made of the twinning direction. Nevertheless, the direction must be one that lies in a plane of symmetry perpendicular to the twinning plane. There are only two such possible planes in a bcc lattice, namely the (110) and the (100) planes. Of these, only the (110) planes are perpendicular to (112), and the <111> direction is the intersection of the two perpendicular planes. It can thus be concluded that <1l1> is the twinning direction. The twinning elements of molybdenum have been reported as the (112) planes and the <111> directions,4 which are also the operative elements in other body-centered-cubic metals, such as W, a-Fe, and ß -brass.5 Thus, the present finding of the twinning elements in Mo- Re alloys supports the concept that twinning formation is mainly governed by the lattice structure. It is of interest to note that for specimens containing 12 at. Pct Re or less, no twins were found after being plastically deformed to as much as 30 pct reduction in height by compression, while for the 35 at. pct Re alloy, twins were formed with less than 1 pct deformation. This, of course, does not exclude the possibilities that for Re-Mo alloys containing 12 pct Re or less, twins could be formed under different conditions, such as at liquid air temperature or under impact loading. The present results, however, suggest that under the same conditions twinning is increasingly sensitive with increasing rhenium content. Consequently, the plastic strain at which twinning starts was found inversely proportional to the amount of rhenium in solid solution with molybdenum. This plastic strain necessary to cause twinning may be used as a criterion in the study of twinning characteristics.

Jan 1, 1961

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By Frank T. Sisco

The discovery of phosphorous is usually credited to the German alchemist Brand, in 1669, and the element was rediscovered the next year by Boyle in England. IT was more than 100 years later, however, before its presence was detected in high-carbon iron produced in early blast furnaces. In 1781 the German chemist Meyer published the results of his investigation on the ?white earth? that he had found in cast iron made from bog ores. This white earth was metallic in appearance, it was extremely brittle, it was readily fusible, and it was not attracted by magnet. Meyer noted that cast iron containing this white earth was more fusible than other cast iron, and he was sure that he had discovered a new metal ? for which he proposed the name Wassereisen, or the Latin term Hydrosiderum. Two years later the distinguished Swedish Chemist Bergmann made the same discovery, finding a ?white calx? in cast iron, which he also mistakenly considered to be a new metal, and for which he proposed the Siderum.

Jan 1, 1944

By V. H. Wilhelm

WITH rapidly diminishing oil reserves: a great percentage of which are uneconomical at present prices, some of the existing methods of development and production will have to undergo radical re- visions to meet the changes continually taking place in the petroleum industry. Imagination in an engineer is a great asset. The fancy of today is found to be the realization of tomorrow, and with this thought in mind, there is here presented a more or less imaginative picture which, to my mind, has a meritorious basis. Directed drilling has reached a stage of accuracy sufficient to allow the prediction that this art will be used in the future development of oil structures, especially those \\,it11 thin sand bodies &apos;and steep dips. Directional drilling in a number of fields in California has gratifying results. Wells which practically laid pipe lines through the oil sands have enjoyed a greater drainage radius with a consequent greater initial and cumulative production. In one field where the vertical thickness of sands was approximately 550 ft., wells drifting at an angle as great as 55 deg. fro111 vertical had over 1100 ft. of perforated pipe in contact with these sands. These wells were, and are, remarkable for their great initial pro-

Jan 1, 1936

By Bunting S. Crocker

Bunting S. Crocker (Executive Vice President, Kilborn Engineering Ltd., Toronto, Ont., Canada)-This is an interesting report on laboratory-scale testing with pebble charges in 12-in.-diam mills, and the author correctly concludes that useful laboratory testing can be done. In the opening paragraphs he states, "laboratory pebble-milling tests have been considered too difficult to perform and not relevant enough to the actual grinding situation"!! This is definitely not so! The writer published detailed tests done in a 12-in.-diam mill comparing pebble and steel balls in 1952 6 and again in 1954 7. We note that our review paper in 1963 was the only one mentioned in the References. The author states that "a smooth lining is more frequently used in commercial-scale pebble grinding." The writer has designed some 22 plants treating 134,000 tpd in North America and Australia. He has also visited pebble installations in Norway, Sweden, Finland, and South Africa. All these plants correctly use heavier lifters than would be considered standard for ball mills of a similar size. Smooth liners are not recommended in wet ore treating plants. In the 1952 paper6 it was clearly demonstrated in the test work that the individual ore pebbles had to be the same weight-not the same diameter or size-as the steel balls if comparable grinding results were to be obtained. In the tests performed in this study most of the pebbles "passed 50-mm round hole screen openings and remained on a 40-mm round hole sieve. Correspondingly most of the ball mill experiments were performed with 50 or 40-mm steel balls". Thus, the balls and pebbles were essentially the same size or diameter. This means we are comparing apples and oranges. When the feed being ground is fine enough the pebbles will be superior. When the feed is coarse the steel balls will be the better. This is similar to grinding tests in which two sizes of steel balls are compared. In the middle of the article, "Crocker5 has reported that equal weights of pebbles and steel balls achieve the same grinding capacities under similar conditions …", then he proceeds to question this postulate. In the eight reports that I have published, I have never made this statement. What I have said is "for comparable grinding, the individual pebbles in the mill charge should be the same weight as the individual steel balls." This is not the first time that I have been misquoted on this point! It is most unfortunate that this test work has been done with a ball and pebble of the same diameter and not the same weight. It is impossible to properly evaluate the results. I also regret the fact that the screen analyses of the tests were not shown. Many of us who have been 40 years or less in the grinding game can easily read screen analyses at a glance. We can tell whether the top meshes are being ground by the ball charge, etc., etc. The graphs are fine for the summary or to illustrate conclusions but are often misleading in the report itself. However, we do agree that useful pebble grinding tests can be done in a 12-in. mill.

Jan 1, 1973

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.&apos; As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.&apos; Other investigators have also studied the binary systems Ti-Cr,3-7&apos; Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a&apos;. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By D. G. Westlake

NUMEROUS hydride habit planes in zirconium, Zircaloy-2, and Zircaloy-4 have been observed by various researchers and have been compiled by Louthan and Angerman.1 While only partial agreement exists on the identification of these habit planes, there is a growing consensus that a tensile stress applied on a polycrystalline rod during slow cooling will cause the hydride platelets to lie perpendicular to the tensile axis. walters2 agrees with Louthan and Angerman who reason that "The particular plane on which precipitation will occur is the plane that will result in the maximum relief of stress by precipitation of the low-density hydride." The experiment described below was initiated to test this hypothesis on a single crystal of zirconium. A single-crystalline tensile specimen of zone-refined zirconium, designated number 13 in a previous study,3 had a square cross section with one pair of parallel faces only 4 deg from the basal plane of the hcp structure. The tensile axis was about 86 deg from the (0001) pole, 14 deg from the (1010) pole, and 16 deg from the (1150) pole. The specimen was charged to 50 ppm H by allowing reaction with the correct amount of hydrogen at 1073°K, homogenizing at this temperature for 2 hr, and cooling in the furnace. Two- surface analysis revealed that hydride platelets had precipitated parallel to the three {1010} prism planes. The specimen was heated to 673°K, in air, for 16 hr to bring the hydrogen back into solid solution, and furnace-cooled to 573°K.* It was then stressed in ten- sion at 1.2 kg per sq mm. (This produced a resolved shear stress of 0.6 kg per sq mm for glide on the prism plane with the highest Schmid factor. A higher stress would have produced significant strain at this temperature because the critical resolved shear stress for prism-plane glide in this crystal was only 1.0 kg per sq mm at ambient temperature.) The poles of the three prism planes were at angles of 14, 46, and 74 deg to the tensile axis so that an applied stress would exert normal stresses on the three planes in the approximate ratios 10:5:1, respectively. As soon as the stress was applied, the sample was furnace-cooled to room temperature. It was ground on wet Sic paper and chemically polished in 50 parts HNO3, 50 parts water, and 7 parts HF before examination. The result of the experiment was negative; i.e., the three (1010) planes were of equal importance as hydride habit planes.* It must be admitted that the ex- periment is not entirely comparable to those performed by walters,2 Louthan,5 and Louthan and Marshall6 on polycrystalline materials. They have found that some critical stress (below the macroscopic yield stress) is required for stress-orienting the hydrides. The applied stress in the present experiment was, by necessity, smaller by an order of magnitude than the critical stresses they report for the various materials. If the critical stress was related to the microstructure, one might postulate that it should be decreased by increasing the degree of perfection of the metal lattice and by increasing the grain size. But the experiment above suggests that, for the extreme case of a zone-refined single crystal of zirconium, the critical stress lies above that which one can apply without introducing gross plastic strain as another variable.

Jan 1, 1967

By C. A. Hartnagel

During- the past 10 years the annual production of petroleum in New York has averaged close to 5,000,000 bbl., the total for the period being 49,881,000 bbl. In 6 of the 10 years, the production was slightly in excess of the 5,000,000 mark. The 1944 production of 4,697,000 bbl. represents a 7 per cent decline from the previous year. Of the total 1944 output, the Allegany County district, which includes two small areas of Steuben County, contributcd 3,614,065 bbl., a decline of 5 per cent from 1943, and the contribution of Cattaraugus County, which represents the northern extension of the Bradford pool of Pennsylvania into New York was 1,082,935 bbl., a decline of more than 14 per cent. Since March 1942, the posted price of New York crude oil has remained at $3.00 per bbl. On lug. I, 1944, a Federal subsidy of 75¢ per bbl. was granted to oil producers, thus making the price actually $3.75 per bbl. Since all of the oil produced in New York comes under the designation "stripper well operations," it is entitled to the Federal subsidy. During the last few years there has been little change in the number of wells drilled annually. In the Allegany field, which accounts for three fourths of the oil produced in the state, 1240 wells, including water-intake wells, were drilled during 1944 as compared with 1223 in 1943. There was no marked increase in the number of wells drilled after granting the subsidy of 75¢ per bbl. of oil on Aug. I, the increase being but 14 wells during the last half of the year over the preceding six months. In flooding operations it is not to be expected that even a substantial increase in the price of crude oil will be reflected quickly in an increase of the number of wells drilled or in a marked increase in production of crude oil. In flooded areas, oil is obtained through a program extending over a number of years. This program involves the drilling of the water or input pressure wells, drilling of the oil wells, building up the oil flood to maximum production, and finally the watering out of the well when the amount of oil produced in proportion to the water becomes so small that pumping is no longer profitable. The various operations may extend over a period of 10 years or more, during which time the price of crude may have fluctuated greatly. Although the rate of production can be controlled to a limited extent, it is evident that a flood when once begun must be continued regardless of the price of crude. During the past seven years New York crude has had a price range from $1.68 per bbl. in 1938 to the present price of $3.75 per barrel The field pattern now in general use for wells in a flood project is the "five-spot." Under this arrangement, the lease is divided into squares with a water well at each corner and an oil well in the center. In the all-over pattern of the lease each oil well is acted upon by four water wells and each water well supplies part of the pressure to four oil wells. Spacing between the input water wells and the oil wells usually varies from zoo to 225 ft. or, on an acre basis, there is one oil well and one water well for each 2 1/2 acres. In recent years there has been a tendency to increase

Jan 1, 1945

By Henry M. Howe

Many direct processes have been proposed for the treatment of oxidized ores of copper by reducing the copper oxide to the metallic state, and by separating it from its impurities by a subsequent fusion. The radical objection common to all the methods which have come to my notice, except those in which sulphur plays the prominent part, is that the very deoxidizing agent which effects the reduction of the copper oxide, inevitably reduces at the same time a very considerable part, if not the whole, of the iron which almost invariably accompanies copper in its ores. The result is that, when the ore is subsequently fused, a very great quantity of the already reduced iron separates from the slag along with the copper, alloying with it, and necessitating costly subsequent operations for its separation. Thus, at Perm, in the Urals," the product of the fusion of ferrnginous copper oxides is a mixture of one hundred and fifty-tive parts of highly cupriferous pig iron with two hundred and fire parts of very impure and ferruginous black copper, containing Pome 10 per cent. of&apos; carbon and iron, though free from sulphur, and of course very difficult to refine. If, in order to avoid this reduction of iron to the metallic state, the reducing action be made feebler, it inevitably results that a considerable part of the copper as well escapes deoxidation; and, consequently, the slags are so rich that it becomes necessary to treat them subsequently in order to recover the copper which they contain. Thus,. in treating native copper, at Lake Superior, where the reducing action is purposely made feeble in order to prevent the deoxidation of the iron, the slags from the first fusion of the ore carry so much copper as to render it imperative to treat them again, which is done in a cupola. And yet, in spite of so far weakening the reducing action as to cause a notable slagging of the copper, a very considerable reduction of iron actually takes place. These are the two dangers which threaten the smelter of oxidized copper ores. If he wishes to avoid slagging his copper, he must have so strong a deoxidizing action as to reduce a great deal of his

Jan 1, 1879

By H. M. Howe

(Read at. the Lake George Meeting, October, 1878.) MANY direct processes have been proposed for the treatment of oxidized ores of copper by reducing the copper oxide to the metallic state, and by separating it from its impurities by a subsequent fusion. The radical objection common to all the methods which have come to my notice, except those in which sulphur plays the prominent part, is that the very deoxidizing agent which effects the reduction of the copper oxide, inevitably reduces at the same time a very considerable part, if not the whole, of the iron which almost invariably accompanies copper in its ores. The result is that, when the ore is subsequently fused, a very great quantity of the already reduced iron separates from the slag along with the copper, alloying with it, and necessitating costly subsequent operations for its separation. Thus, at Perm, in the Urals,* the product of the fusion of ferruginous copper oxides is a mixture of one hundred and fifty-five parts of highly cupriferous pig iron with two hundred and five parts of very impure and ferruginous black copper, containing some 10 per cent. of carbon and iron, though free from sulphur, and of course very difficult to refine. If, in order to avoid this reduction of iron to the metallic state, the reducing action be made feebler, it inevitably results that a considerable part of the copper as well escapes deoxidation ; and, consequently, the slags are so rich that it becomes necessary to treat them subsequently in order to recover the copper which they contain. Thus, in treating native copper, at Lake Superior, where the reducing action is purposely made feeble in order to prevent the deoxidation of the iron, the slags from the first fusion of the ore carry so much copper as to render it imperative to treat them again, which is done in a cupola. And yet, in spite of so far weakening the reducing action as to cause a notable slagging of the copper, a very considerable reduction of iron actually takes place. These are the two dangers which threaten the smelter of oxidized copper ores. If he wishes to avoid slagging his copper, he must have so strong a deoxidizing action as to reduce a great deal of his * Rivot, Prineipes Généraux du Traitement des Minerais Métalliques, i, p. 79.

Jan 1, 1879

By J. A. SINGMASTERN

THE New Jersey Zinc Co.&apos;s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931

By AIME AIME

THAT neither the Reconstruction Finance Corp. nor its subsidiary, the Metals Reserve Corp., are in competition with private enterprise was stressed by Charles B. Henderson in an informal talk before the N. Y. Section, A.I.M.E., on Sept. 23. Among other things, the speaker stated that the R.F.C., since its establishment, had authorized loans of $12,000,000, of which over $8,775,000 has actually been distributed. Of this amount, over $6,600,000 has been repaid. None of this money was appropriated by Congress, the sole assistance from that body being the initial authorization of $500,000,000 capital stock.

Jan 1, 1941

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By F. M. Lewis, E. C. Johnson

Used as a classifier in a plant expanding capacity or changing to closed-circuit operation, the liquid-solid cyclone offers the advantage of being adaptable to existing conditions. This paper presents the costs involved and experience gained from operating a unit of this kind. BY now application of the liquid-solid cyclone to various classification problems in the chemical and metallurgical fields is more or less familiar. A less publicized application receiving wider consideration as time goes on is its use as a classifier in closed-circuit grinding operations. This paper presents the costs involved and the experience gained from operating a unit of this kind. In May 1951 the Tennessee Copper Co. installed in its London mill at Copperhill, Tenn., a liquid-solid cyclone in closed circuit with a 6x12-ft ball mill. The circuit in which this cyclone is used is the regrind or secondary grinding circuit of a copper flotation plant. Originally it consisted of a 7x1-ft conical ball mill in closed circuit with a bowl classifier. Changes made in the primary grinding circuit of the mill necessitated a regrind circuit of greater capacity. The bulk concentrate to be ground was raised from 900 or 1000 tpd to 1200 or 1300 tpd, and to accommodate this increase a 6x12-ft ball mill which had been in the primary grinding circuit was moved into the regrind circuit. When this was done it was found that the classifier was too small to give efficient operation. Space in the plant was at a premium, and since use of the cyclone offered considerable economy the installation shown in Figs. 1-3 was made. The unit installed is a 24-in. diam cyclone classifier with a 20" cone angle. Diameter of the vortex finder is 8 in., the feed entrance area 20 sq. in. Maximum diameter of the adjustable apex valve is 6 in. and minimum diameter approximately 3.5 in. To refer again to Figs. 1 and 2, the cyclone* is mounted motor. It is charged with 18 tons of 1-in. balls. The overflow, or fines, passes by gravity directly to the copper flotation plant. The ball mill discharge and the new feed combine in a sump from which they are sent to the cone by an 8x6 SRL pump at a rate of 497 gpm. Pressure at the cyclone is 5 psi. For reasons dictated by the nature of the ore treated, particularly the bonding of fine grains of chalcopyrite to pyrrhotite, the froth from the second cell of the copper rougher circuit is returned to the regrind mill. This flow, which somewhat complicates the standard closed-circuit calculation, is seen in Fig. 1 to be 156 tpd of solids. This combines with the cyclone classifier underflow to constitute the ball mill feed. The requirement of the regrind product is that it be 77 to 80 pct —200 mesh. The liquid-solids cyclone operating in conjunction with the 6x12-ft mill adequately met this requirement. Of primary importance is the fact that this arrangement provided sufficient classification capacity to replace the undersized classifier and was capable of building up a circulating load to 87 pct, large enough to give an efficient grind. In this instance the circulating load is taken as the ratio of sands to new feed. Any comparison of performance between this liquid-solid cyclone and the replaced classifier would of course be unfair, since the bowl classifier was

Jan 1, 1955