Search Documents

By Pol Duwez, Paul Pietrokowsky

Titanium and vanadium form a complete series of solid solutions at temperatures above 885°C. Below 885°C, vanadium is slightly soluble in a titanium (about 1.5 pct V at 650°C) and a two-phase a plus ß region extends to 18.5 pct V at 650°C. The alloys up to 15.0 pct V transform into a supersaturated a solid solution upon rapid cooling from the ß phase. Above 15 pct V the ß phase may be retained. The temperature at which the ß to a' martensite-type transformation takes place decreases steadily from 850°C for 0.5 pct V to 325°C for 12.7 pct V. IN the transition series of the periodic table, the six elements that have a body-centered cubic structure at all temperatures, namely chromium, vanadium, molybdenum, columbium, tungsten, and tantalum, fulfill the conditions required for the existence of complete series of solid solutions with the high temperature (ß) form of titanium. Up to the present time, complete solubility at temperatures above the a to ß transformation of titanium has been observed in the systems Ti-MO,1,2 Ti-Cb,2 Ti-W,³ and Ti-Ta.³ The two remaining elements, vanadium and chromium, have atomic diameters which are not as near that of titanium as the atomic diameters of the four other elements. Both are smaller than titanium and the difference, expressed in percentage of the titanium atomic diameter, is 12.3 pct for chromium and 8.2 pct for vanadium. On this basis, the least favorable conditions for solid-solution formation are therefore encountered in the Ti-Cr system. The early work on the Ti-Cr system4 revealed that up to about 1100°C the solubility of chromium in ß titanium is limited, and an intermetallic phase exists near the stoichiometric composition TiCr2. It was found later' that a continuous series of solid solutions extends across the diagram at higher temperatures, and TiCr2 forms by solid state reaction. It became apparent therefore that complete solubility would also be present in the Ti-V system. The present investigation confirms this possibility. The iodide-refined titanium used in this investigation was purchased from the New Jersey Zinc Co., New York. According to the manufacturer, a typical analysis of this product is 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb. The Vickers hardness number (10 kg load) of the crystalline bar varies between 55 and 80. The vanadium metal was purchased from the Westinghouse Electric Corp., Lamp Div., Bloomfield, N. J. The purity of this metal is probably above 99 pct V. The oxygen content must have been quite low, since a bar about 1/4 in. square could be cold rolled into a ribbon 0.020 in. thick. To prepare the various alloys on the titanium-rich side of the diagram, the titanium rod was machined into cups 1 cm in diam and about 1.5 cm high. Pieces of vanadium, of the proper weight, were cut from the square bars and placed within the cups prior to melting. On the vanadium-rich end of the diagram, single pieces of the metals, in the proper weight pro-

Jan 1, 1953

By W. R. Foster, J. M. McMillen, A. S. Odeh

The complete equations of average linear momentum balance for a single-phase fluid in an incompreisible, homogeneous, porous medium are derived. The derivation begins with Euler's equation of motion for a continuum and uses an integral transform recently developed by Slattery. 7 For steady flow of a compressible, Newtonian fluid, the usual equations of motion result. For transient flow, the space-time description of the pressure is determined in the lowest approximation by the telegrapher's equation. From the analysis a new phenomenological coefficient results which connects the viscous traction to the deriv ative of the linear momentum density. The magnitude of this coefficient determines the velocity of sound through the pore structure in this approximation to the pressure field. INTRODUCTION The modification of Darcy's law of momentum balance for steady, single-phase flow through porous media has been discussed for many years. The first modification was suggested by Forcheimerl who added terms of higher order in the velocity. These can be expected to appear because the underlying microscopic equations of momentum balance are themselves nonlinear in the point velocity field. The Reynolds tensor pvv, which represents the convective flux of momentum density, appears in the momentum balance equation. Only in rectilinear flow (parallel stream lines) does the divergence of this tensor vanish. Since the steady flow stream lines in most porous media are not parallel, nonlinear dependence of the pressure gradient on the velocity should naturally appear. This nonlinearity has nothing to do with turbulence in the ordinary sense of random fluctuations in the pressure and velocity fields. It arises simply because the stream lines converge and diverge, even for steady flows. Klinkenberg2 demonstrated that the permeability coefficient in Darcy's law depends on the absolute pressure or, alternatively, on the density field. However, because he neglected inertial terms of the Forcheimer type, his correction coefficient could not be represented by a constant but tended toward a constant as the velocity decreased. Forcheimer's and Klinkenberg's modifications can be combined in a rigorous way to account for both inertia and slip during steady flow. This will be shown in a future paper. The transient change of pressure in porous media has been described by the diffusion equation.3 This form results from eliminating the velocity and density fields from a combination of the equations of motion in the form of Darcy's law, the continuity equation and an equation of state. Fatt4 suggested that the cause of deviations from the prediction of the diffusion equation for pressure transients lies not in the choice of Darcy's law as the equation of motion but on the existence of dead-end pores which might invalidate the averaged equation of continuity. On the other hand, Oroveanu and Pascal5 noted chat the time derivative of the momentum density must be included in the equations of motion since this measures the local rate of change of momentum density. Their differential equation for pressure is the telegrapher's equation (neglecting gravity). However, their form of this equation predicts that the speed of pressure propagation through the pore structure is the same as that through the bulk fluid. M. K. Hubbert6 attempted a derivation of Darcy's law by volume averaging the Navier-Stokes equations. Since these equations represent momentum balance at a point within an open set of points containing the fluid itself, Hubbert's volume averaging cannot lead to tenns involving transfer of momentum between the fluid and the walls of the pores. Once these viscous tractions are lost by choosing a control volume containing only fluid, they cannot

By Charles Prasky

ABOUT five years ago the Bureau of Mines began a study, at Minneapolis, of the various methods for beneficiating the low-grade manganese deposits of the Cuyuna range. Several samples of green carbonate slate from the Cuyuna range, containing about 7 pct Mn and about 28 pct Fe, were obtained for this study. The component minerals in the carbonate slate formation were so intimately associated that mineral dressing methods were not suitable for concentrating manganese to a ferrograde product. Although upgrading of manganese and iron minerals has been effected by flotation methods, it appears that manganese cannot be separated from iron except by chemical means. Because the flotation studies at Minneapolis were carried out simultaneously with the hydrometallurgical studies, only crude slate was available for process testing. An important economic consideration in selecting any one of the several chemical methods proposed for recovering ferrograde manganese is the availability of the chemical reagent. Fortunately, large tonnages of sulfur are available on the Cuyuna range in low-grade pyrite and pyrrhotite deposits that are readily concentrated by flotation to a suitable feed for a sulfide roasting furnace as indicated by a Bureau of Mines investigation in 195 0-1951.1 The roasted residue from the sulfide concentrates is a potential source of marketable iron oxide. Therefore, if these sulfide deposits were employed in recovering manganese, utilization of two heretofore unused mineral deposits would be accomplished. Laboratory investigations of several proposed leaching processes were made as a preliminary step in the investigation of hydrometallurgical methods for the treatment of Cuyuna carbonate slate using sulfur as a chemical reagent. From results obtained in the laboratory tests, these leaching processes did not appear entirely suitable for treating Cuyuna carbonate slate. The method developed at the North Central Experiment Station and selected for a more intensive pilot-plant investigation has been termed the differential high-temperature sulfatizing process. Essentially, this sulfatizing process consists of the following steps, described in the order in which the small-scale pilot-plant investigations were made. The first and perhaps most significant step in the process consists of a sulfate roast. Carbonate slate is roasted in an atmosphere of sulfur dioxide gas and air. The overall chemical reaction for converting manganese carbonate to a sulfate at a high temperature in a sulfur dioxide atmosphere follows MnCO8 + SO2 + 1/2 0, = MnSO4 + CO2 (H077°O = —64,180 cal per g mol) .' The need for concentrated sulfuric acid is avoided. Fine grinding is not essential. Removal of carbon dioxide from the slate during roasting produces a more porous structure and permits easier permeation by the sulfatizing gas mixture. The temperature limits for this conversion of manganese have been established as 600" and 850°C. Iron sulfate is unstable and is not formed at these temperatures; phosphorus is not converted to a water-soluble form; and polythionates are not formed. The second step in the process consists simply of a water leach of the sulfatized product. Manganese sulfate in the sulfatized product is dissolved in water. Iron, phosphorus, and calcium remain in the leach residue as water-insoluble products. The third and final step consists of the recovery of ferrograde manganese oxide from manganese sulfate leach solution. Water is evaporated from the leach solution, and impure monohydrate crystals of manganese sulfate are recovered. The moist crystals are formed into pellets or extrusions and thermally decomposed to produce a ferrograde manganese

Jan 1, 1958

By Caudle B. H., Cooper H. E. Jr., O. K. Kimbler

The results of studies of areal sweepout behavior in nine-spot injection patterns are presented in this paper. The ratio of the production rates of the two types of producing wells in a nine-spot pattern is considered in its effect on breakthrough. A model study was used to develop a method to predict the production histories of both side and corner wells and to develop the production history of the pattern or the field. INTRODUCTION The importance of areal sweepout behavior in injection operations has been recognized for a number of years. We now know that the fraction of a reservoir which will be reached by an injected fluid is a function of the geometric arrangement of the production and injection wells and of the mobility ratio of the fluids. Of these two, the mobility ratio (which is a measure of the relative ease with which the oil and the injected fluid can move through the reservoir) appears to have the greatest effect on recovery. The effect of mobility ratio on production history has been reported for most of the dispersed injection patterns (i. e., five-spot, staggered and straight-line drives).4-6 ere has been very little published on the nine-spot injection pattern. This may be because the two types of producing wells in the nine-spot pattern can—and sometimes should —be produced at different rates. This adds a second variable (the fist being mobility ratio) to be covered in a study of the nine-spot flooding network. Muskat1 has reported the sweep pattern efficiency at breakthrough for a mobility ratio of one at various ratios of producing rates for the two types of wells. For these conditions he found maximum oil production at breakthrough to occur when the corner well (the producing well farthest from the injection well) is produced 10.7 times as fast as the side well. Other investigatorsa2,3 have studied a few of the many possible operating conditions possible with this injection pattern. This paper presents the results of studies which are strictly applicable to a nine-spot injection pattern surrounded by other nine-spots in a homogeneous reservoir and which has no flowable gas present (no oil bank is formed). Although the full ranges of the variables mentioned above have not been covered, the results reported here should allow reasonable estimates of field operations to be made. EXPERIMENTAL The well spacing geometry of the nine-spot pattern is shown in Fig. 1. Here we see that each injection well is surrounded by eight production wells arranged in a square. Four of these producing wells are located at the corners of the square; the other four are in the midpoints of the four sides. These two types of producing wells are called "comer wells" and "side wells" respectively. It is the ratio of the producing rates of these two types of wells that affects the breakthrough recovery, as calculated by Muskat.' This ratio is defined as the total producing rate of a corner well divided by the total producing rate of a side well. The model used in this study represented one-eighth of a nine-spot pattern, as shown in Fig. 1. It contained the equivalent of one-fourth of a side well, one-eighth of a comer well, and one-eighth of an injection well. Because of these proportions, the actual producing rate ratios in the model were one-half of the ratios of producing rates as

Jan 1, 1965

By E. H. Edwards, J. Washburn, E. R. Parker

The mechanism of strain hardening was discussed in connection with some recent observations on the stress-induced motion of dislocation boundaries and on the simple shear deformation of zinc, cadmium, and copper crystals. THE nature of work hardening accompanying plastic deformation of metals has long been the subject of speculation. As early as 1925, Becker' suggested a thermodynamic process to explain slip based on the statistical probability for the occurrence of local glide steps. The theory that plastic glide was due to the presence of lattice defects known as dislocations was first introduced in 1934 by Taylor: and Orowan, and Polanyi.4 Taylor presented a rather complete analysis of the behavior and interaction of dislocations. He assumed a certain type of stress field to be associated with a single dislocation, and postulated that work hardening would result from plastic flow in two ways. First, dislocations following one another across a slip plane might encounter a barrier which would impede their movement, thereby gradually diminishing and eventually stopping plastic flow on that plane. The second mechanism involved the concept of dislocations traveling in opposite directions on nearby planes attracting one another to form a meta-stable lattice. The interaction of dislocations in such an array was shown to be large enough to require an increase in stress before plastic flow would continue. Kochendorfer5,6 extended the concept of work hardening involving a back stress due to an accumulation of like dislocations on a slip plane. He suggested that the formation of a new dislocation is hindered by those dislocations already present. The hardening resulting from the interaction of newly forming dislocations with bound dislocations was designated as "formative hardening," and indicated to be the only type of hardening necessarily connected with the slip process. In another detailed picture of work hardening, Mott and Nabarro7 assumed that sufficient dislocations are primarily present in the crystal as a consequence of growth irregularities (mosaic structure) to initiate slip. Work hardening resulted from the interaction of migrating dislocations with localized internal stresses produced during deformation. More recently, however, Mott8 as modified his treatment to include the generation of dislocations at Frank-Read sources and he accounts for the hardening by the formation of sessile dislocations. It has been widely accepted that metals of hexagonal structure, usually possessing only one set of glide planes, exhibit mechanical behavior markedly different from those having cubic structures. However, the differences in behavior of the two classes may be less fundamental than suggested. Rohm and Kochendorfer9 have shown that a single crystal of aluminum subjected to approximately simple shear gives the type of stress-strain curve associated with the hexagonal metals. Similar behavior has been demonstrated for gold and silver crystals by Andrade and Henderson.'" Thus when glide in cubic metals is restricted to one plane, the strain hardening characteristics closely resemble those of the hexagonal metals. It would appear, therefore, that an investigation of some of the strain hardening properties of single crystals sheared in simple glide might provide a more complete understanding of the phenomenon of work hardening. This report relates a number of recent observations made on single crystals of copper, zinc, and cadmium tested in simple shear. In addition, pertinent observations of effects accompanying stress-induced movement of dislocation boundaries are reported. Experimental Procedure and Results Details of the production and advantages of the type of single-crystal shear specimen employed for the following tests have been presented in a previous publication.n The method of testing makes

Jan 1, 1954

By L. W. Sink, B. H. Kear, S. M. Copley, M. F. Hornbecker

IT is well known that under appropriate conditions of chill casting, many metals and alloys develop a columnar grain structure having a high degree of preferred orientation.' In cubic materials, this principle has been employed to produce shaped castings with a unidirectional cube oriented columnar grain structure as well as shaped single crystals with a cube axis parallel to the growth ais.' "he purpose of this note is to describe how this same principle can be enlployed to produce wires, rods, or more complex crystal Shapes with a variety of conlpositions in cube or random orientations by a single casting operation. The procedure for directional solidification of in Fig. 2. Examination under crossed polarizers indicated that the striations were a second phase (presumably the B19 phase) which frequently forms initially at primary grain boundaries and then grows toward the interior as thin ribbons. X-ray studies on filings of this alloy reannealed at 1300°C for 15 min indicated a strong pattern of the fcc phase together with a substantial pattern of the B19 phase. The un-annealed filings, however, showed only the pattern of a cold-worked, fcc structure. In these two-phase alloys it appears, therefore, that the B19 phase is transformed into a disordered fcc structure by cold-working. The mechanical properties of these alloys would be of some interest since a fcc structure might be expected to possess greater ductility than the or-thorhombic B19 structure from which it forms. The author wishes to thank Mr. Harvey Yakowitz and Mr. Richard Manuszewski for obtaining the photomicrograph in Fig. 2. This research was partially supported by Research Grant DE-02455 from the National Institute of Dental Research. columnar grained ingots involves pouring a melt into a preheated mold having a water-cooled copper chill at its base? and controlling the temperature gradient in the mold so as to maintain columnar grain growth from end to end of the ingot.4 This is illustrated schematically in Fig. l(a). It should be noted that the longitudinal temperature gradient promoting unidirectional columnar grain growth is maintained by heat loss primarily through the solidifying ingot to the chill, so that both the temperature gradient and the growth rate diminish with increasing distance from the chill. As the distance from the chill increases? the columnar structure coarsens, and the perfection in preferred orientation tends to increase progressively. Using this same procedure of gradient solidification, Fig. l(b) shows a simple scheme for producing a batch of crystals having the same cube orientation rather than an assemblage of columnar grains. Wires and rods are produced by cementing ceramic tubes to the wall of the mold. The steep temperature gradient produced in the central chamber is controlled by the mold heater to produce favorable conditions for crystal growth. Clearly the success of the operation lies in the selection of individual growing columnar grains by some kind of orifice at the base of each channel in the mold. Using simple constrictions, experience with nickel-base alloys has shown that 4 -in.-diam holes at a distance of -1 in. from the chill yield crystals within 7 deg of (100); closer control of orientation is possible by placing the crystal selector farther away from the chill.

Jan 1, 1970

By R. A. Morse, W. W. Owens, D. R. Parrish, T. M. Geffen

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By D. R. Parrish, T. M. Geffen, R. A. Morse, W. W. Owens

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By L. A. Roe, John Jan

Iodine is a soft, lustrous, grayish-black nonmetallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue-violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 25 and 35 million lb per year, of which about 30% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and seawater. According to the US Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (I03)3 (calcium iodate), and dietzeite, Cat (103)2 (CrO4), (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapaca provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in Table 1. Table 2 lists estimated world iodine reserves. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated reserves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. Markets and Prices Iodine and its compounds are generally marketed in the form of: iodine, crude; iodine, resublimed; calcium iodates; calcium iodide; potassium iodide, sodium iodide, and numerous organic compounds. Product Specifications Crude iodine, World market: 99-99.5% 12. Crude iodine, US produced, average: 99.8% 12. Crude iodine, USP XVII Specs: not less than 99.8% percent I2. Resublimed iodine is usually 99.9% and ACS specifications call for not over 0.005% total bromine and 0.020% nonvolatile materials (Anon., 1971). Prices, c.i.f. United States, for iodine have been steadily increasing from $1.18 per lb of crude in 1967 to $6.37-7.27 in January 1981 (Anon., 1981). In 1980 the price of iodine increased by 50%.

Jan 1, 1983

The following is an extract of the Engineers' licensing law recently passed by the Colorado legislature; it went into force July 10. On the board of examiners are representatives of the four national societies. R. J. Grant, of Denver, represents the American Institute of Mining and Metallurgical Engineers; H. I. Reid, of Colorado Springs, the. American Society of Civil Engineers; H. S. Sands, of Denver, the American Institute of Electrical Engineers; and Frank E. Shepard, of Denver, the American Society of Mechanical Engineering. Within sixty clays after the taking effect of this act the Governor of the state shall appoint a State Board of Engineer Examiners, to be composed of five members, who shall be legal residents of the state of Colorado and who shall have been engaged in the practice of engineering for at least ten years. Upon the expiration of the term of any members other than the state engineer the governor shall appoint their successors for a term of four years, from a list of five nominees elected by the licensed engineers acting in a general assembly called together for this purpose by the president of the board. Such assembly shall be held in the month of January next preceding the expiration of the terms of any members. The Board of Examiners shall adopt all necessary rules, regulations and by-laws to govern its proceedings, not inconsistent with this act or the laws of the state or of the United States.

Jan 8, 1919

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A 1/2x4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four 5/s in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of 3/s yard capacity, both manufactured by Blaw Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1950

By L. H. Sjodahl, J. B. Conway

of each particle on grain boundary movement is proportional to the area it occupies on the grain boundary and this increases with the square of the particle radius. In contrast to the impression gained by Tiwari the effectiveness of a particle, as a grain boundary obstacle, increases rapidly as the particle size increases. The counterbalancing factor in a dispersion of constant volume (e.g., those considered by Zener) is of course the rapidly diminishing number of particles, a situation which does not exist in thoria dispersed materials where the volume fraction of thoria remains constant. Although it has been assumed that the Zener approach is valid for the sake of the above argument, it is open to the following objections: 1) It assumes that the effect of many small particles along a grain boundary is cumulative and does not take into account the possibility of each small particle being overcome separately. In this case the boundary will not be able to move forward until the largest particle on the boundary has been overcome. This means that the rate controlling factor will be the rate at which a few relatively large particles are overcome with the remaining small particles playing a negligible role. 2) When the dispersion consists of very small particles the interparticle spacing is usually small compared to the grain size and most particles are located away from grain boundaries where they can play no part. The most efficient dispersion, from a purely geometrical viewpoint, is one where the particle spacing is equal to the grain size so that all the particles are on grain boundaries. Tiwari's second point that voids cannot prevent re-crystallization seems to be unfounded as several workes20-23 have shown that voids alone can retard grain boundary movement and recrystallization. To further convince Tiwari, Fig. 17 shows a void in deformed TD Nichrome holding back a recrystallization interface. Tiwari's explanation for the effect of voids on recrystallization, i.e., they reduce local strain energy and hence lower the driving force for recrystallization may be valid in itself but is irrelevant to the present case where even complete recrystallization after ONE of the more recently proposed expressions for describing stress-strain behavior is that due to Voce.1,2 This equation is usually written: s =s8 ?(s8?so)e??/?c [l] where s is the true stress, ? is true strain, cC is a constant called the characteristic strain, s8 is the asymptotic stress approached at high strain values, and so is the threshold stress at which the plastic deformation begins. While this expression has not been universally accepted as yet it does contain certain features which are consistent with experimental stress-strain behavior. In a more recent publication Hsu, Davies, and Royles3 employed the concept of generalized strain proposed by seth4 and identified a method for linearizing the stress-strain plot. In this approach the generalized strain was given by: where 7 is the generalized strain, 1 is the instantaneous length, 1, the datum length, and n is a constant called the "coefficient of strain measure". A value of n was said to exist which would yield the linearity: s —s+ S[.-(tf] [3] In recent studies of both these approaches, it has been found that while the Voce equation and the gen-

Jan 1, 1970

By Zavis M. Zavodni, Carl D. Broadbent

During the past 15 years, rock mass structural properties have become acknowledged as the focal point for rock slope design. Re- search into the methods for measuring and incorporating structure into the design effort has taken many directions and has produced a variety of useful techniques. Among the findings at Kennecott has been the realization that structure-controlled instability can be categorized as regressive or progressive depending on the relative geometries of slope and structure and on the strength characteristics of the structures. It was further identified that a failure condition can initiate as regressive and in time become progressive should external stimuli increase or structure characteristics be altered due to extensive displacements. The transition point has been shown to be a useful indicator of the expectable collapse time. This paper defines three fundamental failure types as dictated by structure and offers discussion on the practical value of such a classification to slope design and failure control. Several prominent examples of failures typifying the categories of structure- controlled instability are discussed. An application of f allure prediction based on the regressive-to-progressive transition point is described.

Jan 1, 1983

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap ' charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73' 27' and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap ' charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73' 27' and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse-grained high-purity aluminum at temperatures approaching the melting point permitted the formulation of a theory of subgrain formation. Subgrain boundaries were found to be formed by two different processes: kinking and polygonization. Polygonization is considered as the main factor in subgrain formation. SINCE "slipless flow" was first discussed in detail by Hanson and Wheeler,' many studies have been undertaken to determine how metals deform at high temperatures. Several types of observations have been reported. Jenkins and Mellor,² working on the creep of mild steels and various grades of commercial irons, found metallographic evidence of a kind of substructure within the grains after deformation at high temperatures. Homes" observed after creep deformation of steel at high temperatures that the original X-ray spots were sharply divided into several small ones. The same phenomenon was reported by Hirst4 from his studies on lead and later by Crussard5 from his work on aluminum. The works of these investigators demonstrated beyond any doubt that the splitting of the X-ray spots was due to the fact that the grains underwent a division into subgrains during deformation at high temperatures. Since then, numerous experiments have been undertaken on aluminum in order to determine the mechanism of formation of subgrains. Research workers can be divided, for the purpose of discussion, into two different groups as regards thinking on subgrain formation. On one hand, based on the work on polygonization by Cahn,6 Guinier and Lacombe,7 Greenough and Smith," Crussard,10,11 and Servi, Norton, and Grant," it was concluded that subgrain formation was a consequence of the simultaneous effects, first, of inhomogeneous deformation which produced bending of the lattice, and second, polygonization. On the other hand, Wood and coworkers13-16 based their work on the results of an earlier report" which dealt with crystallite size and a fragmentation theory. It is interesting to note that while Greenough and Smith8 and Wood et al. performed similar experiments, their conclusions were quite different. Wood et al. did not recognize polygonization as a fundamental mechanism and said that aluminum, at the beginning of the deformation, fragmented immedi- ately into subgrains in order to permit deformation of the metal, the number of these subgrains being a function of strain rate and temperature. They concluded that deformation of grains occurred by flow along the subgrain boundaries. In view of the contradictory conclusions, it would appear that the data were not explicit enough to provide an unambiguous conclusion. It appears that the techniques by which most of the results were obtained, namely, X-ray work, were not enough by themselves to solve the problem. Another approach was needed. In the present research, therefore, an extensive metallographic study was planned to supplement the X-ray work. The importance of revealing the subgrain boundaries metallographically was realized, and this will explain the extensive development and use of etching techniques. In order that subgrains would be considerably larger and therefore more readily visible under a microscope, the creep experiments were performed at very high temperatures approaching the melting point of aluminum. Development of Experimental Technique Creep tests were run at constant load on high purity (99.995 pct) aluminum specimens having a very coarse grain size. None of the specimens was run to fracture. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled in the gage section to permit

Jan 1, 1954

By N. A. Gokcen, M. N. Dastur

In metallurgical process industries a knowledge of true melting and casting temperatures is very essential for increasing the operating efficiency as well as improving the quality of the finished product. Optical pyrometers are widely used for the purpose because of their cheapness and ease of operation. It is an unfortunate fact, however, that this mode of measuring temperature entails a source of severe error inasmuch as with all non-black bodies, the temperature observed is always below the true temperature owing to deficient emissive power. Hence, the need for emissivity correction arises. In 1913 Bidwell1 obtained emissivity values of 0.36-0.48 for a temperature range of 1520-1800°C. He measured the true temperature of molten iron by sighting into a carbon cavity immersed in the iron under an atmosphere of hydrogen. In 1914 Burgess2 determined the emissivity of a smooth surface of liquid iron free from oxide to be 0.37 under an atmosphere of hydrogen. He claimed to have attained an accuracy of within 5°C at 1500°C with an optical pyrometer using monochromatic light. He reported that no difference appeared to exist between the emissivities of pure iron and of steels containing considerable percentages of carbon, nickel or manganese; nor was there any appreciable variation of emissivity with temperature from 1530 to 1571°C. Wensel and Roeser3 found an elnissivity value of 0.4 for temperatures above 1375°C for cast iron. The average emissivity value for carbon steels reported by Leiber,4 odd,5 Hase6 and Umino7 range from 0.4 to 0.45. Knowles and Sarjant8 made an extensive study of emissivity of molten iron and steel over a wide range of workshop and laboratory conditions. Observations of true temperature were made with immersion thermocouples, and correlated with apparent temperatures indicated by optical pyrorneter readings taken on the pouring stream as it passed over the lip of the crucible. The emissivity of Armco iron was shown to be of the order of 0.4, rising slightly with increasing temperature. But for plain carbon steels containing up to 1.0 pct carbon the emissivity was shown to fall slightly with increasing temperatures. The results of their investigation are in agreement with those of Guthmann.9 Naeser,10 Spencer," Todd5 and Hase6 in regard to the relation between emissivity and temperature for plain carbon steels. However, Goller12 has found a rise of emissivity with increasing temperature for the same steels. Results of several investigations are given in Fig 1. Measurement of True and Apparent Temperatures The necessity for an accurate optical temperature scale for liquid iron in studies of gas-metal equilibria led to this investigation. Experimental measurements were carried out in the induction furnace used by Dastur and Chipman13 in their studies of the reaction of hydrogen with oxygen in liquid iron. The furnace as modified for this work is shown in Fig 2. The atmosphere of the furnace was a mixture of purified argon with hydrogen containing a small controlled amount of water vapor. Gases were preheated by means of a platinum-10 pct rhodium resistance coil. The stream of hydrogen sweeping across the surface of niolten iron vir-

Jan 1, 1950

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4'5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

By R. J. Stokes

This paper compares the room-temperature mechanical behavior of magnesium oxide crystals containing 'fresh' and 'grown in' sources. 'Fresh' dislocation sources introduced by cleavage or mechanical contact move and multiply to generate slip bands at 3000 psi. Macroscopically the crystals yield smoothly at 6000 psi and can be quite ductile. When 'fresh' sources are eliminated by chemical polishing the crystals have to rely on 'grown in' sources to initiate slip. They then deform elastically up to extremely high stresses (-30 to 50,000 psi) yielding with a sharp stress drop down to the level at which Ifresh' sources operate. Grown in' sources are considered to be associated with impurity wecipitate particles or inclusions. Annealing crystals at 2000°C dissolves these particles thereby eliminating sources for slip. The crystals then become consistently stronger (> 70,000 psi) approaching within 1/10 of the theoretical strength. Dislocations of the grown-in network do not move under stress to nucleate slip. It is proposed that they are locked electrostatically. DISLOCATIONS were originally conceived to resolve the large discrepency between the theoretical and real strength of solids. The idea that slip propagates by the movement of dislocations is now well confirmed both by electron transmission and etch pit studies. But this by itself is not sufficient to explain the low yield strength of crystals for there is still the need to understand where slip dislocations originally come from. Theoretical estimates place the stress to generate dislocations homogeneously in the lattice at approximately 1/30 of the shear modulus,' a value 104 to 105 times greater than the stress at which the very first manifestations of plastic deformation have been observed. Only an special cases can the theoretical strength be approached; in crystals of high perfection such as whiskers2 where dislocation sources do not preexist and in covalent crystals where the dislocations present at room temperature are almost completely immobilized by the bond character of the solid.3,4 For the most part it is necessary to assume that the yield strength of ionic and metallic solids corresponds to the motivation and multiplication of dislocation sources present beforehand. The question as to their origin appeared to be answered by the suggestion of Frank and Read5 that dislocations forming part of the grown-in structure could operate as a mill for the large scale production of dislocations. The Frank-Read mechanism is still widely accepted as the source of dislocations but a number of observations have been reported which are in serious disagreement with it. One of the most intriguing of these is that under normal testing conditions dislocations of the grown-in network appear to play no role in the plastic deformation of rock salt structure ionic solids. This was first reported in the etch pit studies on lithium fluoride by Gilman and Johnston6 and is true also for magnesium oxide. To explain the comparatively low yield stress of lithium fluoride it was proposed by a number of authors7,9 that small unresolved prismatic loops formed by vacancy condensation were acting either directly or indirectly as the dislocation sources. This proposal led Gilman10 to perform a series of detailed and careful experiments on lithium fluoride to try to identify the sources responsible for the initiation of slip. He concluded that prismatic loops played no general role and that other sources were more important. Dislocation sources in ionic crystals can be divided into two general categories. First, there

Jan 1, 1962