Search Documents

By Thomas M. Drown

In experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

Jan 1, 1930

By Eugene McAuliffe

NO physical impairment can be more serious than the partial or complete loss of sight. With reasonably good eyesight, a person is equipped to care for life and I limb, provided a rational measure of t caution is manifested. When the sight of one eye is lost or badly impaired, one-half of this God-given asset is gone, and extreme care must be taken to prevent the tragedy of total darkness that closes out the beauty of sky, field and mountain, the faces of relatives and friends, and either removes entirely or in part one's capacity to produce and earn. During 1933, The Union Pacific Coal Co., operating ten coal mines in Wyoming, decided to undertake a visual survey of all of its mine operating officials and employees. Although the cost of workmen's compensation paid because of eye injuries was material, the management was more deeply concerned with the social loss and the suffering resulting from the many eye injuries. As every element of coal production cost must be scrutinized, accurate data on all accidents, with the workmen's compensation paid therefor, are carried forward monthly. The number of accidents to eyesight and the resultant compensation paid are shown in Table 1 for nine calendar years:

Jan 1, 1934

By Ernest J. Stocking

ENGINEERS are the key men in our war program today. Upon the technical knowledge and skill of the engineer and upon his administrative and executive abilities rests the entire success for the production of vital materials of the war. Naturally the work load of the engineering examining unit of the U. S. Civil Service Commission has increased greatly since our active participation in the war. At present, over 550 separate requests for certification of eligibles are received by the engineering unit per week. These represent more than a fourth of the total requests received for personnel by the Commission's central office at Washington and represent a recruitment work load of three to four times that carried by the whole Commission previous to January 1940. These requests represent a minimum of a thousand vacancies to be filled each week, while an average week will produce, at present, approximately 1400 vacancies and a weekly maximum may approach well over 2000 vacancies.

Jan 1, 1942

With a mine output as high as 5000 tpd and mill capacity of 7000 tpd, the uranium mining and milling complex owned and operated by Kerr-McGee Nuclear Corp. in the Ambrosia Lake area is the largest in the U.S. and is likely to remain so for some time. Next year, Kerr- McGee expects to have in production another mine in Section 19 of the Ambrosia area-and will begin ore production in 1976 at its new $15-million mine at Church Rock, located northeast of Gallup, N. M., where the company has already completed the shaft work and is in the early stages of project development. Ore from Church Rock will be transported to the company's facilities at Ambrosia Lake for processing. Kerr-McGee's existing eight mines in Ambrosia Lake go to depths of about 800 to 1500 ft to tap the various horizons of uranium-bearing sands in the Westwater Canyon of the Morrison formation.

Jan 8, 1974

By R. M. Brick, F. L. Vogel

THE elementary mechanism of deformation in the body-centered cubic metals has been a subject of dispute for many years. If the problem were merely that of designating the crystallographic plane or planes of slip, the solution would have appeared long ago. However, there must be greater differences in the deformation behaviors of the body-centered and face-centered types than the differences in their lattices would suggest. The lines of slip formed on the polished surface of a strained face-centered cubic metal conform to glide over a single plane of the crystal. Slip in body-centered cubic iron, however, is frequently observed as curved and forked lines which could not possibly define a single plane of atoms. This alone is sufficient reason to expect different modes of deformation to operate in the two lattice types. The literature in this field now has generally accepted the proposition that {110), {112), or (1231 planes will act as slip planes in iron. It is essential that the experimental evidence supposedly supporting this proposition be critically examined. Taylor and Elam1 in 1926, using relatively small single crystals, determined the operative slip systems by measurements of the distortion of a grid engraved on the specimens prior to deformation. Their results indicated that shearing had taken place in the close-packed direction on a plane adjacent to or coinciding with the plane of maximum shear which contained the slip direction. This led the authors to propose a theory of noncrystallographic or banal slip. The authors considered an alternate rationalization of banal glide. Slip on two (1101 planes or possibly two {112} planes containing the same <1ll> direction could produce the wavy slip lines. By employing plane segments of varying widths, the integrated plane could take any position in the <111> zone. They rejected this explanation, however, feeling that the preponderance of evidence was against it. Taylor&apos; continued the investigation of the plasticity of the body-centered cubic lattice on ß brass. He reasoned that the resistance to shearing of a given plane in the zone of the slip direction was a function of the angle between the glide plane and the closest (110),: P F=—cose sine cos(X —?) [1] where F is the resistance to shear; P, the axial load at yielding; A, the cross sectional area; e, the angle between slip direction and load axis; x, the angle between plane of maximum shear containing the slip direction and the (101) pole; and ?, the angle between observed glide plane and the (101) pole. Differentiating Eq. 1 and rearranging, dF — = tan(x-?) d? [2] F which expresses the variation of the shear resistance with the angle $. Integrating this equation between the limits 0 and ? yields In F/F0 = ?0?tan(x— ?) d? [3] Here, F, is the resistance to shear of the (110) plane and F is the resistance to shear of a plane $ degrees from the (110). Thus, the variation of shear resistance with $ can be calculated from an experimentally measured x vs $ relationship. Fahrenhorst and Schmid8 sed several methods, none of them involving direct observation, to determine the glide system in ferrite. They determined the variation of critical resolved shear stress with

Jan 1, 1954

By Don Simon

In the late 1960s the mining industry was in an apparent slump due to a combination of factors. Enrollment dropped significantly at schools offering mining engineering degrees, resulting in a shortage today of experienced mining graduates to staff middle management positions. How has this limited supply affected salaries? Does the shortage impair the mining industry&apos;s ability to respond to national energy needs?

Jan 12, 1979

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By Alan Kissock

MOLYBDENUM is thought of as one of the rarer elements, for though it occurs in almost every country of the world it is seldom found in commercial quantities. In this country, however, there is one deposit which makes the term "rare" a misnomer. There are two commercially mined molybdenum minerals: molybdenite, the sulfide, and wulfenite, a lead molybdate. Of these two only the former is of any con- sequence but wulfenite is of mineralogical interest. It is frequently associated with oxidized lead ores and particularly in arid sections. Deposits, however, are usually quite superficial. It is highly oxidized and yet it does not appear to be an alteration product for it apparently disappears below water level and I know of no case where primary molybdenite, or in fact any molybdenum whatever has been identified below these surface wulfenite occurrences. The genesis of wulfenite would make an !- interesting study.

Jan 1, 1933

By Paul F. Kerr

The insufficiencies of our mineral resources are becoming well known, and the national political conscience seems to be troubled at last by our dependence upon mineral commodities which must come from other lands. This realization places increased responsibility upon the industrial, educational, and governmental groups whose task it will be to solve the problems of mineral supply. As we all know, from the time that man first sought mineral deposits until recent years, prospectors have been largely responsible for mineral discoveries. Today the era of the prospector is almost over. The human ants that have literally examined all accessible outcrops and have tested the gravels of nearly all stream beds in the United States have left undiscovered few worthwhile mineral deposits within the scope of their recognition. The pages in the history of mineral exploration are now being turned from the era of the surface prospect to the era of the hidden de- posit.

Jan 1, 1949

By J. J. Sense

This paper deals with the Asarco method for the determination of equipment availability. It is apparent that no single availability equation will provide all of the information necessary for the complete record of equipment availability. In the Asarco system, three separate availability records are carried on major equipment. The first is mechanical availability, the second is operational availability, and the third is a historical record of equipment use. The derivation of the three items and the definitions of the time elements used in the various availability equations are presented and discussed. The Mission unit of American Smelting and Refining Co. is located in Pima County, Ariz., approximately twenty miles southwest of Tucson. The unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to company smelters at Hayden, Ariz., or El Paso, Tex. Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tpd concentrator was started in the spring of 1960. The first ore was treated in midsummer of 1961 and full ore production was reached in August 1961. At that time over 46 million tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tpd. Total production to date (ore and waste) is over 120 million tons. Major equipment currently in operation at the Mission pit is as follows: 3 P & H 1800 Electric Shovels - 9 cu yd dippers 1 P & H 1900 Electric Shovel - 9 cu yd dipper 2 B.E. 190-B Electric Shovels - 9 cu yd dippers 35 Euclid LLD Trucks - 60-ton capacity 6 KW-Dart 55-T Trucks - 55-ton capacity 1 KW-Dart D-2550 Truck - 65-ton capacity 1 LeTourneau Westinghouse 65 Haulpak - 65-ton capacity 3 Euclid S-18 Scrapers - 274011 capacity 4 Caterpillar D-8 Dozers 4 LeTourneau Westinghouse Tournadozers 1 Michigan 280 Dozer 2 Caterpillar Model 12 Motor Graders

Jan 1, 1964

Jan 1, 1896

In reply to inquiries and comments which have reached me since the publication of this paper, and in explanation of some seeming discrepancies between my statements in the text concerning the amount of displacement of the faults, on one hand, and certain figures in the plates on the other hand, I give here, with some additional remarks, my measurements of the displacements in the different sections, which it originally seemed unnecessary to print : By displacement, I mean neither the throw, i.e., the vertical distance apart of the two edges of a faulted bed (what Mr.

Jan 1, 1896

By J. L. Weeks

THERMAL conductivities of several samples of uranium and uranium alloys were determined using an apparatus previously described.&apos; The value previously reported for uranium,&apos; 0.035 cal per sec per cm per "C at 70°C, is in error due to the failure of a thermocouple during the determination on uranium. The defective thermocouple was detected after a reanalysis of the data obtained during the run and since has been replaced. Subsequently, runs on several samples of uranium show the thermal conductivity of uranium to be 0.069 cal per sec per cm per &apos;C at 70°C. The accuracy of the determinations was checked by measuring a sample of synthetic sapphire whose thermal conductivity was previously reported and found to be in agreement with other values."-" The values given in Table I are believed correct to % 3 pct or 0.003 cal per sec per cm per "C, whichever is larger. The samples were provided by J. H. Kittel of the Argonne National Laboratory, Metallurgy Div. References J. L. Weeks and R. L. Seifert: Apparatus for the Measurement of the Thermal Conductivity of Solids. Review of Scientific Instruments (1953) 24, pp. 1054-1057. J. L. Weeks and R. L. Seifert: Note Regarding the Thermal Conductivity of Synthetic Sapphire. Journal American Ceramic Society (1952) 35, p. 15. :&apos; J. Francl and W. D. Kingery: Thermal Conductivity: IV, Apparatus for Determining Thermal Conductivity by a Comparative Method; Data for Pb, Al2O3, BeO, and MgO. Journal American Ceramic Society (1954) 37, No. 2, Part 11, pp. 80-84. (Part 11: special issue on thermal conductivity.) &apos; W. D. Kingery, J. Francl, R. L. Coble. and T. Vasilos: Thermal Conductivity: X, Data for Several Pure Oxide Materials Corrected to Zero Porosity. Journal American Ceramic Society (1954) 37, No. 2, Part II, pp. 107-110. (Part 11: special issue on thermal conductivity.) Edwin Ruh: New Jersey Ceramic Research Station, Rutgers University. Private communication.

Jan 1, 1956

By Frank Linforth

THE object of this paper is to present a brief outline of the methods of geologic mapping employed in the Geological Department of the Anaconda Copper Mining Co., at Butte, and to show by means of a few typical examples the practical nature of the results obtained. The extremely complicated geological conditions early encountered in Butte mining led mine operators to realize the necessity of accurate detailed geologic mapping as an aid to successful development of the ore bodies. The organization of the Anaconda Geological Department was undertaken in 1900 by H. V. Winchell, who, in conjunction with D. W. Brunton, worked out the essential methods of procedure which are, in the main, followed at the present time. Since the year 1906 the geologic work has been under the direction of Reno H. Sales, and in some respects the scope of the work has been slightly enlarged. Au excellent article describing the general equipment of the geological department was presented by D. W. Brunton at the British Columbia meeting of the Institute in 1905.1 His idea, that data collected underground and recorded should be put to practical use and not remain a mere " inventory of the company&apos;s underground possessions," is the keynote to the success of applied geology in Butte. The geologic notes are taken as soon as possible after the ground is broken so that any mistake in the mining may be corrected at once, or any particularly advantageous procedure may be suggested before any useless work is done. Taking the notes underground is a comparatively simple matter, but a few necessary precautions may be pointed out. The essential to success is that the notes shall show exactly what geological facts are disclosed. The observer must discriminate carefully between important and unimportant exposures in making the record, especially as regards the relation between veins and stringers, between faults and minor slips, or between the characteristics of veins of different ages. A simple color scheme has been adopted for making this record: Red pencils are used to indicate.

Jan 11, 1913

By Philip Wilson

THE genesis of some orebodies has been explained by the mingling and chemical interaction of water solutions of different compositions and the consequent precipitation of the mineral load of one or both solutions at their confluence. While this process can be proved in the laboratory, rarely can a positive demonstration be found in nature, for the conditions at the time an ore deposit is being worked are usually entirely different from those that existed when the orebody was formed. For this reason, the present deposition of copper carbonate in the southern end of the Briggs Mine of the Calumet and Arizona Mining Co. near Bisbee, Ariz., is of great interest. The developed orebodies in the Calumet and Arizona mines are roughly confined to two broad parallel zones separated at the north by a wedge of. Copper Queen ground and at the south by an undeveloped block of Calumet and Arizona ground about 2000 ft. (610 m.) wide. The more westerly zone includes the Irish Mag, Oliver, P. and D., and Cole mines, none of which have been operated since 1919. Much of the water from this division is carried from the 1400-ft., or bottom, level at the southern end of the Cole mine in a long water drift through the undeveloped block to the 1300-ft. level of the Briggs mine at the southern end of the more easterly zone.. Most of this water comes originally from outlying areas in the P. and D., mine, passing through parts of the lower levels of the Cole mine, which are heavily mineralized with iron and copper sulfides. This sulfide zone has been opened up and slowly oxidizing for years. Originally a pure, potable water, the analyses of which are shown under A in Tables 1 and 2, on its way through the mineralized area in the Cole mine it gathers copper, calcium, magnesium, iron, and aluminum sulfates, a load of dissolved mineral salts almost four times as great as that which it formerly carried; analyses B

Jan 7, 1922

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,&apos; or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9&apos; per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,&apos; or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9&apos; per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

D. J. DEMOREST,* Washington, D. C. (written discussion ?).-This paper is a real contribution to technical science; it will make it&apos; easier to think accurately about the inner workings of a blast furnace. I was rather surprised to read that the authors regarded as a new discovery the idea that a molten mixture of CaO, A1203, and Si02 is a molten solution of the compounds of these oxides rather than of the oxides in each other. Surely no. chemist with an active respect for the known facts of chemical affinity could believe that these oxides could be melted together without forming compounds, and that these compounds would then dissolve in one another. This work does, however, help to establish what it was supposed must be true. I think it is worth while, in the light of the work of the Geophysics Laboratory, this work of the Bureau of Mines, and that of previous investigators, to visualize what happens as a charge passes down through a blast furnace, thinking especially of the slag-forming materials. These are chiefly kaolin (Al203.2SiO2.2H2O), quartz, and limestone. These substances do not undergo much change until the limestone decomposes at about the middle of the furnace, whereupon the chemical affinities of CaO and SiO2 must begin to he active; especially if there is any amorphous Si02 present. This forms CaSiO3, and the SiO2, CaSi02 and Al2-032SiO2 then come together to form the binary and ternary eutectics so well located by the work of the Geophysics Laboratory. No matter how much lime has been charged into the furnace, the formation of this eutectic will start it about the same height in the furnace and the gangue will start to get pasty at the same height. If the charge is such that the

Jan 4, 1918

By John Fritz

MEMBERS of the American engineering societies who were in London and Paris during the last days of. June and early July were present at many interesting gatherings. The official delegates of the Founder societies were the specially honored guests of the foreign engineering societies, but other American engineers took part in the meetings. The members of the delegation were: Arthur S. Dwight, Charles F. Rand, William Kelly, representing A. I. M. E.; Ambrose Swasey (general chairman of deputation), Ira N. Hollis, Jesse M. Smith, representing A. S. M. E.; F. B. Jewett, A. E. Kennelly, G. O. Squier, representing A. I. E. E.; Charles T. Main, Robert A. Cummings, John R. Freeman, D. C. Henny, representing A. S. C. E.

Jan 1, 1921