Search Documents

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By P. F. Gnirk, J. B. Cheatham

An experimental investigation has been made to study the effects of tooth angle and confining pressure on the force required for indentation of dry rock samples under confining pressure. In these experiments static single-tooth indentations were made on two standstones, a limestone, a schist and a slate under confining pressures of 5,000 to 15,000 psi. Sharp wedge-shaped teeth with included angles ranging from 30°to 105°were used. In all cases the force-displarenzent curves are approxinlately linear for rocks tested under confining pressure, as contrmted with the discontinuous curves obtained for silnilar rocks at atmospheric conditions. Photonzicrographs of thin sections through the craters indicate very little evidence of chip formation during indentation. In general the experimental data lie between calculated values for perfectly rough and perfectly smooth tooth-rock interfaces. INTRODUCTION The variables associated with ctrilling at depth are numerous and, in many instances, are not easity isolated and controlled. Also, many of these variables are interdependent; however, if the variables which are sufficiently independent of each other are held constant and are appropriately introduced, the dependent variables can be more easily studied and evaluated. It is the purpose of the present investigation to study experimentally the simplest case of bit tooth-rock interaction. In essence, the experiments have involved the static loading of sharp wedge-shaped tools on the surfaces of effectively semi-infinite dry rock samples subjected to confining pressures. During this investigation the following quantities have been maintained constant: 1. Pore pressure: atmospheric (i.e., the rock is dry). 2. permeability: although the rocks may be permeable, they are "jacketed" in such a manner that the fluid is not permitted to flow through them. 3. Temperature: 75F. 4. Rate of loading: essentially static (approximately 0.002 in./second). 5. Bit tooth: a sharp wedge-shaped tooth loaded normal to the rock surface. 6. Rock surface: smooth and flat. 7. Drilling fluid: hydraulic oil. In addition to the above conditions, the rock surface was free of a layer of cuttings. There was no indexing to previously indented surfaces, and the influence of corners of the borehole was neglected because the rock samples were effectively semi-infinite. The following quantities have been varied, and the resulting effects have been studied: 1. Rock a) Type (e.g., limestone, sandstone, etc.). b) Mechanical properties ) Necessarily dependent c) Porosity on type of rock. 2. Bit tooth (included angle of wedge-shaped tooth). 3. Depth of penetration. 4. cobfining pressure. On the basis of laboratory experiments which have shown that many rocks exhibit ductile behavior at confining pressures corresponding to depths usually reached during drilling,'.' a theory has previously been advanced which predicts the force required for penetration by a single sharp wedge tooth into a ductile* material.' The material is assumed to be isotropic, homogeneous and rigidly plastic (no elastic deformation) and to obey the Coubomb yield criterion (Figs. 1 and 2). Equations governing the force required for penelration are given for two extreme cases:** 1. A smooth, perfectly lubricated tooth-rock interface (fridionless boundary), in which the solution gives a minimum value for the penetrating force: in which F = force of the tooth, b = length of tooth edge,

By L. Guttman

THE equilibrium diagram of the indium-thallium system was of interest to us in connection with a study of the superconducting properties of metallic solid solutions in progress at this Institute. For this purpose, a series of alloys was prepared covering the range from pure indium to 75 atomic pet TI, and X-ray diffraction patterns were obtained. Roughly speaking, the results indicated a region of continuous decrease in the axial ratio of the face-centered tetragonal structure from the value ca. 1.08 in pure indium to unity at about 23 atomic pct TI. From this concentration to the solubility limit, the structure was face-centered cubic, a form not reported by Hansen.1 At this point we became aware of the work of Valentiner,2 who had found the same structures at room temperature but had not investigated further the relationship between them. To study the transformation f.c.c.??f.c.t., and to clarify the phase diagram, we undertook the work reported in this paper and that which follows." Preparation of Alloys Pure indium and thallium* (both about 99.9 pct, as estimated from spectroscopic analyses) were weighed out in quantities sufficient to prepare 10 to 25 g of alloy of the desired concentration. (Occasionally indium was mixed with a previously pre- pared solution.) The metals were melted over a flame, in an open graphite crucible, stirred with a graphite rod, and poured into a graphite trough. The rough slug was hammered and swaged into a rod of 2 to 3 mm diam, and annealed in a drying oven at about 125°C for 1 to 2 days. Samples were taken from the rod for analysis, as well as for diffraction and other measurements. The thallium was determined by electrometric titration, using a modification of the method of Beale and co-workers.' The precision of analysis was generally about 2 0.2 pct of the thallium content. The rods were sometimes found to vary in thallium content as much as 1.5 pct from end to end, but since analyses were also made close to the segments used in the various studies, the composition was usually known as accurately as the analyses could be made. Where one less significant figure is given, the error is estimated to be ±0.4 pct of the thallium content. X-Ray Diffraction Measurements Three different cameras were used: (1) A 7 cm Debye camera, with oscillating specimen (manufactured by the Picker X-ray Corp., Cleveland, Ohio); (2) a 9 cm diam Debye camera of the type designed by Bradley;" (3) a 10 cm diam symmetrical focusing back-reflection camera (manufactured by Geo. C. Wyland, Ramsay, N. J.). Samples were prepared from the homogenized rods, either by filing under liquid nitrogen, or more often, in the form of wires or foils made by working at room temperature or liquid nitrogen temperature. Sharp patterns were obtained from specimens annealed at room temperature, although higher annealing temperatures were also used (cf. below). Generally, copper radiation was used; a few patterns were obtained with

Jan 1, 1951

By H. Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion bf overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 5, 1961

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970

By A. V. Henry, W. Harry Vaughan

THE kaolins of the southeastern United States were known to civilization as early as the latter part of the eighteenth century-and yet the [ ] commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported. Occurrence Georgia kaolin occurs in an irregular belt extending diagonally across the middle of the state, a distance of approximately 225 miles. This belt

Jan 1, 1937

By Donald L. Everhart

SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the over- all job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Com- pared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits.

Jan 9, 1954

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

By S. J. McCarroll

THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.1 During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO, process was constructed. Numerous operation difficulties ensued, and the plant was closed when the manganese situation in the country eased.

Jan 3, 1954

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12'3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By R. Maddin, A. Lawley

Single crystal Mo-Re alloys (99.99+ purity), grown by electron bombardment floating zone heating, were deformed in tension at temperatures from -196° to +200°C. At -196oC, Mo-6 pet Re and Mo-20 pct Re alloys deform by slip on systems of the type (101) [1ll]. Above-78oC, the operative slip system is of the type (112) [111], (101) [1ll], or (211) [1ll], depending upon orientation. Mo-39 pct Re alloys deform by twinning and slip at all test temperatures with a (112) [111] type twinning system. Critical resolved shear stress for slip and twinning is calculated as a function of composition and temperature, and the mechanical properties compared with those of less Pure polycrystalline alloys. HEXAGONAL close-packed rhenium, c/a = 1.615, is highly soluble in molybdenum. The bee molybdenum-rich solid solution extends to approximately 42 at. pet Re* at 2500°C,&apos; Fig. 1. Recent work on polycrystalline alloys has shown conclusively that the addition of rhenium to molybdenum improves both the fabricability and the low-temperature ductility.2"5 Similar behavior is observed for W-Re and Cr-Re alloys.5 Initially, Geach and Hughes2 found that the Mo-30 pct Re alloy could be cold rolled to approximately 90 pct reduction before the onset of cracking. The remarkable effect of the rhenium was later confirmed by Jaffee et al. 3-5 with an optimum condition of maximum strength combined with maximum ductility at the Mo-35 pet composition. At higher rhenium contents, the ductility was severely impaired due apparently to the presence of brittle tetragonal s phase, Fig. 1. In the Mo-35 pet Re alloy, at least 110 ppm (parts per million) oxygen could be tolerated before cold workability was reduced. By comparison, the corresponding tolerance figure in unalloyed molybdenum is ~ 10 ppm. The effect of rhenium was considered in terms of: 1) a reduction in oxygen solubility in the lattice; 2) a redistribution of intergranular oxide from grain boundary films to isolated spheres; and 3) the promotion of twinning as a further mode of plastic deformation. Paradoxically, twinning is often associated with brittle fracture in iron and the silicon irons.6&apos;7 Work to date has been restricted to are-melted and powder metallurgy polycrystalline material of ~ 99.9 pet purity. The present investigation was initiated for the purpose of determining the mode and crystallography of plastic deformation of a series of bee Mo-Re alloy single crystals over a wide temperature range from -196o to +200°C. Using high-purity zone-melted material (~ 99.99 + pet purity), the specific role of rhenium in the molybdenum lattice may be understood more fully since effects due to grain boundaries and oxide redistribution will be absent. At the same time, the study provides a comparison of single and polycrystalline deformation behavior. EXPERIMENTAL TECHNIQUES A) Preparation and Purity of Single Crystals. Alloys in the form of either are-cast and swaged or sintered and ground bar, 0.120 in. diam, were obtained from the Chase Brass and Copper Co. Alloy single crystals ~ 8-in. long were grown from the

Jan 1, 1962

By David R. Mitchell, Ernest M. Spokes

INFORMATION on magnetic properties of minerals other than magnetite is scanty and some- times erroneous. Often there is no information at all. W. R. Crane&apos;s table of tractive forces published in 1901 is still the best guide in the field, but Crane&apos;s data can be used as a guide only, since he ignored such important factors as impurities in the minerals, size, and packing effect. During the 1930&apos;s work by the U. S. Bureau of Mines added greatly to knowledge of the behavior of certain minerals in a magnetic field. The USBM bulletin gave for the first time complete magnetic characteristics for magnetite and fragmentary data for a few other minerals. The work reported here covers a study of the magnetic-susceptibility relationships of the wolf-ramite series of minerals and sphalerites as related to their chemical compositions. Theories are proposed to explain divergences found from commonly accepted beliefs.

Jan 3, 1958

By L. D. Lash

The key to successful liquid-liquid extraction is the solvent. First, and most important, it must be highly selective for the metal desired and yet reject other metal ions present; second, the ideal sol- vent is completely insoluble in the aqueous feed liquor; third, it has rapid phase separation and will not form emulsions; and, fourth, low cost is desirable, since losses occur even though the solvent is recycled. For this application a solvent known as DDPA (dodecyl phosphoric acid) was chosen since it closely met these requirements. DDPA is a long-chain alkyl phosphate developed for AEC by Oak Ridge National Laboratories, Dow Chemical Co., and the U. S. Bureau of Mines. The long chain contributes to low solubility in the aqueous phase and to high extracting power from acidic sulfate solutions, whereas the alkyl phosphates generally exhibit high selectivity for uranium solutions.

Jan 11, 1958

By F. W. C. Boswell, R. L. Cunningham, H. M. Weld

Chemical analysis shows the partition of the magnesium addition between the metal and the graphite is independent of whether the graphite is in the form of nodules or flakes. The bright central spot observed in nodular graphite polished sections is shown to be due to the structure of the nodules. DURING the past few years numerous papers have been published on the production1-7 and heat treatment" of nodular cast irons. However, very little information is available on the structure of the nodules and the reason for their formation. It would appear that an explanation of the phenomenon of nodulation must await a detailed knowledge of the nature of the nodule. Disagreement exists among various workers on such a fundamental point as to whether or not a nodule actually contains a microscopically visible, nongraphitic nucleus.9-11 Work was initiated with a view to obtaining definite information on this and other aspects of the problem. Chemical Separation and Analysis Microscopic appearance had indicated9-11 that a nongraphitic core might exist in nodules (Fig. 1). It appeared that a chemical comparison of separated nodules and flake graphite would be profitable, for if the core is nongraphitic a relatively large amount of certain elements would be found in the nodules as compared to the flake. This comparison could best be made by obtaining nodules and flake from the same melt of cast iron, part of which had been in-noculated with a suitable addition reagent for the formation of nodules. A 300 lb melt was produced. About half of this was innoculated in the ladle with an Fe-Si-Mg alloy to produce nodules and cast into keel blocks; the remaining half of the melt had silicon added in an effort to compensate for the silicon in the innoculant used in the other half of the melt and this was cast into similar keel blocks. The analyses of the resultant irons are given in Table I. Nodules and flake were chemically extracted from 2 kg samples of metal as described in the appendix. While this method dissolved the iron and chromium carbides, it did not dissolve the titanium, vanadium, and molybdenum carbides. These latter carbides could have been removed by nitric acid, but in other experiments it was found that it attacked pools of metallic iron entrapped in the nodules which had, until the nitric acid treatment, been protected from the attack of the sulphuric, hydrochloric, and hydrofluoric acids. It will be shown in the next section that entrapped iron exists in nodules but not in flake. On microscopic examination many tiny irregular particles were observed to accompany both the nodules and the flake. These were identified by tabling a sample of nodules from which a sufficient fraction was obtained for X-ray analysis. A good pattern of titanium carbide was obtained indicating that this was the predominant compound present. Since it was not possible to determine how completely the carbides could be removed mechanically and since their removal from flake is much more difficult, it was decided not to resort to any separation as this would render further comparisons more difficult. The samples were ashed in a combustion

Jan 1, 1953

By C. W. Spencer, Che-Yu Li, R. J. Knight

The usual reaction product for the monotectic reaction in the Bi-Se system consists of rod -shaped particles of selenium-rich liquid embedded in a single crystal matrix of At certain crystallo-graphic orientations of the matrix with respect to the reaction interface, more complex shapes are as -sumed by the liquid particles. This reaction has been examined at different growth rates and relative crystallographic orientations of the matrix with respect to the reaction interface. The uhriation in auerage particle size of the liquid phase with reaction rate has been determined at one crystallograpIzic orientation of the matrix. On a plot of logarithm of average particle diameter vs logarithm of reaction rate, data points for crystals grown at rates of 10- to 1.0 cm per hr fall near a curve of slobe -0.4. MONOTECTIC reactions in binary alloy systems are reactions of the eutectic class in which, as the system is cooled through the three-phase reaction isotherm, one liquid phase (L) decomposes to a solid phase and another liquid phase (LII).&apos; A partial phase diagram, as taken from Hansen, showing the monotectic reaction in the Bi-Se system is given in Fig. 1. This diagram specifies the monotectic point at 618°C and 72 at. pct Se, and the monotectic reaction products as the intermetallic Bi Se3 and a liquid (LII) which contains approximately 98 at. pct Se. At a lower temperature, 217°C, this liquid may undergo a eutectic reaction in which the reaction products are BizSe3 and crystalline selenium. However, under conditions of rapid cooling, or quenching, from above 217°C, this selenium-rich liquid may be partially retained to room temperature in an amorphous or glassy state. The intermetallic BizSe3 is rhombohedral, of the space group jm;&apos; however, for convenience it is usually represented by a hexagonal struture. A pronounced plane of cleavage, which lies perpendicular to the main axis of the rhombohedral unit cell or parallel to the basal plane of the hexagonal cell, exists in the structure. The usual monotectic reaction product consists of rod-like particles of LII embedded in a single-crystal matrix of BizSe3, although at certain crystallographic orientations of the matrix BizSe3 other more complex shapes are assumed by LII. A similar rod-like, or cylindrical, morphology for the carbide phase has been reported by westbrook7 in the a Cr-Crz3Ce eutectic structure. In this paper the morphological characteristics of the LII particles, as retained to room temperature, have been examined under conditions of varying growth rate and crystallographic orientation of the matrix BizSe3 with respect to the growth direction. EXPERIMENTAL PROCEDURE Alloy specimens corresponding to the monotectic composition, 72 at. pct, or 50 w pct Se, were prepared from 99.999 pct pure bismuth and selenium obtained from the American Smelting and Refining Co. The two elements, corresponding to a total specimen weight of approximately 30 g, were encapsulated in 13 mm OD Vycor tubing under a vacuum of 5 x X mm of Hg. The capsules were suspended on a fine platinum wire in a Bridgman-type furnace which exhibited a temperature gradient of

Jan 1, 1963

By D. H. Gieskieng

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely Werent materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected capacity data. Recording instruments are connected to crushers in such a manner that a continuous record is produced which discloses the inherent maximum capacity of the crusher and shows capacity decreases caused by hangups. The capacity effects of various crushing conditions are made more evident by this arrangement. The recording instruments were first applied to a standard sized 10 by 7 in. Blake-type jaw crusher in the laboratory. Suficient tests were run on this with various combinations of setting, throw, speed, feed sizing, shapes of jaw plates, and other operating features, to establish the individual effect of each on the capacity. The instruments later were applied to much larger crushers in the field, through the excellent cooperation of the managements in the Mesabi Iron Range, and data were obtained which closely corroborated the established trends. The capacity equation resulting from the test work is made up of a series of factors, each representing the contributing effects of setting, speed, width of chamber, nip angle, feed density, type of jaw plates, stroke, and the overall operating technique. Fortunately, most of these factors were revealed to be in direct proportion to the capacity for straight plate chambers. This equation is also applicable to chambers using curved plates, with slight modifications resulting from the capacity limitation of the upper portion of the crushing chamber. The equation has been derived from tests covering a very wide range of feed density and hardness. It has been found valid, providing that the feed material is either nonpacking in character, as is usual, or allowance in designing the crushing chamber shape has been made to accommodate this characteristic. Preliminary investigation has shown that the equation is also applicable to single-toggle jaw crushers. Conditions of this are that the top of the flywheel rotate towards the top of the crusher opening, and that the horizontal motion of the swing jaw relative to the stationary jaw at the discharge opening be considered as the stroke. The relatively large upper chamber jaw motion would probably result in realiza-

Jan 1, 1950

By R. A. Stauffer

The chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll&apos;s and Dr. Schlecten&apos;s recent paper1 has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000ºC in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating-to about 1000ºC in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. The Replacement of Li2O in Spodumene A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide Present in the Ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh&apos; Analysis of the spodumene was as follows: PCT SiO2......................... 62.7 Al2O3........................ 29.9 Li2o......................... 4.9 Na2O........................ 0.89 CaO......................... 0.75 MgO........................ 0.49 K2O......................... 0.44 Lime (cp —200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000ºC in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1949

By E. F. Bradley, R. I. Jaffee, H. R. Ogden, E. S. Bartlett, D. N. Williams

The mechanical properties of solid-solution-strengthened columbium alloys have been assessed as a function of alloying additions. Studies included the effects of tungsten, tantalum, molybdenum, and vanadium. Elevated temperature fabrication was required at alloying levels above about 15 pct W or 10 pct Mo. Tungsten, molybdenum, and vanadium additions increase tensile strength at room temperature and 2200°F, but tantalum additions exert little strengthening. Similarly, tungsten, molybdenum, and probably vanadium additions increase the ductile-to-brittle transition temperature, and tantalum additions decrease this parameter. The 2200°F stress-rupture strength is increased by tungsten and molybdenum additions; with 20 to 25 at. pct additions, 100-hr rupture strengths of 30,000 psi are obtainable. Small vanadium additions exhibit mild stress-rupture strengthening, and tantalum additions are innocuous. At 2500°F, tungsten additions retain stress-rutpure strengthening capability, but molybdenum additions are much less effective. Tantalum additions augment the stress-rupture strengthening of tungsten plus molybdenum additions at 2500°F. Of the refractory metals, columbium possesses specific potential for structural use in the temperature range from 2000" to about 2500°F. Desirable features of columbium are its good low-temperature ductility, ease of fabrication, oxidation mechanics (lack of a volatile oxide at moderate temperatures), good availability and reserves, and relatively low density. However, alloying is required to provide attractive strength at elevated temperatures. Published information concerning alloying be- havior of columbium relative to mechanical properties is sketchy, particularly in consideration for long-time applications at temperatures in excess of 2000°F. Only a few stress-rupture data at temperatures from 2000" to 2500°F have been reported;&apos;-&apos; these are too meager to allow rationalization of the effects of various alloying additions on creep or stress-rupture properties. Additional published data do, however, give some insight toward understanding of systematic alloying behavior for columbium relative to low-temperature strength4-&apos; and ductility,&apos; and elevated temperature tensile behavior.4,6 This paper is intended to augment previous knowledge, and to promote understanding of the alloying behavior of columbium for long-time structural service at elevated temperature. BASIC CONSIDERATIONS Solid-solution strengthening is recognized to be of prime importance in improving strength in columbium-base alloys. Other strengthening mechanisms may be (and are, in current alloys) used to augment solid-solution strengthening. As strengthening results primarily from lattice distortion, the strengthening effectiveness per atom depends upon atomic size mismatch between solvent and solute. Another factor in this regard is conformance to ideal solution behavior in the solid solution. Thus, for example, despite appreciable differences in the degree of mismatch between tungsten (5 pct), molybdenum (5 1/2 pct), and vanadium (7 1/2 pct) in solution in columbium, all are about equally effective in straining the columbium lattice at room temperature.&apos;-&apos; Similarly, tantalum additions do not strain the columbium lattice, and little strengthening is expected. Size effects being equal, maximum solution strengthening at high temperatures is anticipated to result from the addition of elements that increase the melting temperature of columbium. This expectation is based on an increase in the electronic bonding forces exhibited in the transition metal series as electronic structures approach those of the Group Vl metals. Of the metals that exhibit ex-

Jan 1, 1963