Search Documents

JAMES DOUGLAS Dr. James Douglas, twice President of the American Institute of Mining Engineers, and one of its principal benefactors, died in New York on June 25, 1918, at the age of 81 years. After a life of extraordinary activity, failure of his health compelled him to retire about 2 or 3 years ago, and in view of his advanced years his death was not unexpected. His funeral was held at the Church of the Mediator, on June 26, and was attended by representatives of the American Institute of Mining Engineers and of the Canadian Mining Institute. His body was then taken to Quebec for burial in the family plot. An extended notice of Dr. Douglas, prepared by Dr. R. W. Raymond, will be presented in the September issue of the Bulletin. LEWIS NEWTON BAILEY Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., April 30, 1918, at. the age of 34 years. He was Master Engineer, .Senior Grade, in the Fourth Regiment, U. S. Engineers; and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character.

Jan 8, 1918

By H. O. Hofman

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. IN a previous paper,1 The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation, into the behavior of calcium sul-phate in air; that, is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Moissan,3 and Abbegg,4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851 with carbon monoxide; Gmelin Kraut 5 add Leplay and Laurent (1848) as third investigators. Metallurgical authorities confine their statements to the known fact of reduction by carbon. II. PREPARATION OF RAW MATERIALS. 1. Calcium Sulphate.-This salt was prepared in the same manner as described in our previous paper,6 and was found to be chemically pure. * Professor of Metallurgy, Massachusetts Institute of Technology. + Metallurgical Instructor, Imperial Technological Institute. 1 Trans, xxxix., 628 to 653 (1909). 2 Handbuch der anorganischen. Chemie, vol. ii., part 2, p. 309 (1894). 3 Traité de Chimic Minérale, 1904, vol. iii., p. 543. 4 Handbuch der anorganischen Chemie, vol. ii., part ii., p. 116 (1905). 5 Handbuch der anorganischen Chemie, vol. ii., part 2, p. 233 (1909). 6 Trans., xxxix., 630 (1909).

Nov 1, 1910

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

Organization Place Date 1919 American Railway Engineering Association Chicago, 111. Mar. 18-20 Society of Industrial Engineers New York, N. Y. Mar. 18-21 American Electrochemical Society New York, N. Y. Apr. 3-5 National Foreign Trade Council Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y. May American Institute of Electrical Engineers Lake Placid, N. Y. June

Jan 3, 1919

By H. O. Hofman

WITH the exception of lead sulphate, all common metallic sulphates are completely decomposed upon heating into metallic oxide, sulphur trioxide, sulphur dioxide and oxygen. Some give up their trioxide readily at a low temperature, others require considerable heat and much time to be completely freed from sulphur. Kerl in 1881 arranged the principal metallic sulphates as they are decomposed by a rising temperature in the following order: silver, iron, copper, zinc, nickel, cobalt, manganese and lead, lead sulphate being decomposed only slightly at a white heat. The researches of Bradford, published in 1903, show, however, that ferrous sulphate is decom¬posed at 590° C., cupric sulphate at G53° C. and argentic sulphate at 1,095° C. By the present investigation it will be seen that zinc sulphate is decomposed at 739° C. As far then as our present knowledge goes, the order in which the decomposition of the leading metallic sulphates takes place is the one given in Table I.

Jan 1, 1905

By Elmer W. Pehrson

NINETEEN FORTY-SIX was an eventful year for the mineral industries. Perhaps the most significant development was the socialization of industry in Great Britain, initiated in 1945 but carried to fruition in the coal industry in 1946. On Jan. 1, 1947, management of the coal industry will be vested in a National Coal Board, responsible to the Ministry of Fuel and Power. A sum of £164,660,000 has been provided to compensate private owners for assets transferred to the Board. The British coal industry has been a problem for many years. Production has declined to a point where serious shortages of fuel for domestic needs have developed. Exports have dwindled to a small fraction of the previous trade. Costs have increased greatly, and quality has deteriorated. The industry's physical plant has not kept pace with the rapidly mounting wage scales in recent years. Some claim that the best and most accessible coal reserves of Britain are heavily depleted. The industry has been harassed by difficult labor problems, including bad morale among the workers and a shrinking labor force.

Jan 1, 1947

By Donald L. Katz

THE Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July 1, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produces 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand' indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplification and generalizations are necessary to give the over-all picture in so short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, r, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City. Wilcox Secondary Recovery Association on Sept. 5;.1940. Some information is taken from a report to the Association by C. V. Sidwell on March 1, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." HISTORY OF WILCOX ZONE The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. 12.1 .4 and areal map of Fig. 2. The sand is of Ordivician age and is composed of well assorted, rounded' sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 was dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1937 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1941

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By C. Laird, C. E. Feltner

IN previous workif2 we have shown that the steady state cyclic stress response of pure copper tested in the low cycle fatigue range was determined only by the plastic strain amplitude and the test temperature. hus, copper, at any given temperature, has a unique cyclic stress-strain curve independent of prior history. Cu-7.5 wt pct Al, however, showed a stress response for a given plastic strain amplitude and temperature which depended sensitively on prior history. From this work we predicted that all wavy slip mode materials, typified by copper, would have a unique cyclic stress-strain curve; whereas all planar slip mode materials, typified by Cu-7.5 pct Al, would not. This prediction has now been tested for a number of materials of widely varying crystal structure and slip character. Wavy slip mode materials studied include: Fe. Al, Cd, disordered FeCo-V, and Cu-3 pct Co (quenched and aged). Planar slip mode materials investigated include: Fe-3 pct Si, ordered FeCo-V, disordered Ni3Mn, ordered Ni3Mn, and Zn. The treatment and properties of these materials are listed in Table I. Cyclic stress-strain curves were determined by controlled plastic strain tests (see Ref. 1 for details) at room temperature for all materials in both the initially annealed and cold worked conditions. The results obtained for iron and Fe-3 pct Si are typical of wavy and planar slip mode materials, respectively. The cyclic stress-strain curves for these materials are shown in Fig. 1 and it can be seen that iron has a unique cyclic stress strain curve while Fe-3 pct Si does not. Aluminum, Cu-3 pct Co, and disordered FeCo-V showed a behavior like that for iron, while Ni3Mn in both the disordered and ordered condition behaved in the same manner as Fe-3 pct Si. These results therefore support the general conclusion drawn in Refs. 1 and 2 that. for wavy slip mode materials, a cyclic mechanical equation of slate it =t.(hcp, i. T) is approximated in which the satura-

Jan 1, 1970

By L. S. Birks

The bainite transformation in a 3.5 pct Ni-1.25 pct Cr steel was studied under various conditions of cooling and stress. Several characteristics may be specified: 1) transformation in the bainite region (925° to 575°F) is very little affected by the manner of cooling from the austenitizing temperature at 1600°F to 575°F)tothe upper limit of bainite transformation at 925°F; 2) starting time for the bainite transformation is the same order of magnitude for either isothermal transformation or continuous cooling, but the rate of transformation is somewhat greater for isothermal transformation; 3) tensile stress accelerates both isothermal and continuous cooling transformation, and 32,000 psi stress changes the form of the isothermal transformation diagram to correspond in appearance to the continuous cooling diagram; 4) transformation for nonlinear, continuous cooling may not be determined directly from the linear, continuous cooling transformation diagram, but may be predicted by assuming first that the fractional amount of austenite transformed in a given small temperature interval depends on the approximate linear cooling rate during that temperature interval and then by summing stepwise over the whole temperature range. IN a previous publication' an X-ray spectrometer was described with which the X-ray diffraction from a specimen could be observed continuously under controlled temperature and tensile stress. This instrument has now been applied to a study of the austenite-bainite transformation in a Ni-Cr steel for both isothermal and continuous cooling conditions, with and without stress. Certain characteristics of the transformation lead to a method of predicting the amount of transformation to be expected at a given temperature for any type of cooling curve. Material and Specimen Preparation The steel chosen for the investigation was a Ni-Cr steel having the composition in the following percentages: 0.30 C, 0.27 Mn, 0.019 P and S, 3.50 Ni, and 1.25 Cr. In order to fabricate specimens suitable for the X-ray spectrometer, a 1/4 in. plate was ground down to 0.060 in. and then cold rolled to about 0.035 in. Next it was heat treated by quenching in oil from 1650°F and tempering at 1200°F for 1 hr. Then it was etched in dilute nitric acid to reduce its thickness to 0.014 in. and cut into blanks in the shape of flat tensile specimens 3 1/4 Vi in. long, 7/16 in. wide, with a notch % in. long and 7/32 in. wide; see Fig. 1. X-Ray Technique Since the X-ray spectrometer has been described in detail elsewhere,' only a brief outline of the principles will be repeated here. A focusing, pow- der-diffraction arrangement' was used, as shown schematically in Fig. 1, and the specimen was mounted vertically in a vacuum furnace (not shown in the figure). The X-rays, moving in a horizontal plane, enter and leave the furnace through beryllium windows. As shown in the figure, X-rays diverging from the line source A are diffracted by the specimen B and converge at the detector slit C. The detector D and the slit C may be set at the proper angle in the horizontal plane to receive X-rays diffracted by either the face-centered phase (austenite) or the body-centered form (ferrite, bainite, martensite). The specimen is heated by electrical conduction between connectors E, and E,, and a Pt—Pt-10 pct Rh thermocouple spot-welded to the center of the notched region on the side away from the X-ray beam indicates the temperature continuously on a Brown recorder. Temperature control is exercised manually with a variable transformer on the input to E,-E,. Any desired time-temperature relationship is easily obtained by first drawing the desired curve on the temperature recorder chart and then adjusting the variable transformer during the run so that the thermocouple

Jan 1, 1957

Jan 1, 1929

[A AALSETH, Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Monl ABADIE, Henry G (M 43) Asst to Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif ABBE, T Waldo (A 56) Asst Dist Oper Supt Sun Oil Co PO Box 66, Stowell, Tax ABBOTT, Fred E Jr (M 59) Abqaiq Dist Mgr Arabian American Oil Co Dhahran, Saudi, Arabia ABBOTT, Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT, J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT, Richard H (J 51) Partner Abbott & Howard 422 W Hermosa San Antonio 12, Tex .ABBOTT, William G (M 50) Div Mgr Rice Engrg & Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN, Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carmi, III ABEL, Malcolm D (J 50) Gen Partner Abel & Bancroft PO Box 865, Midland, Tex ABEL, Ramond L (M 28) Prof of Chem Eng Univ of Pittsburgh, Pittsburgh 13, Pa ABEL, Wayne K (M 57) 1513 Patton Drive, Odessa, Tex ABELL, Joseph M (J 55) Petr Engr Tennessee Gas & Oil Co Box 1772, Casper, Wyo ABELS, Thomas A (J 60) Exploit Engr Shell Oil Co Box 193, New Orleans 3, La ABENDROTH, G F (M 46) Dring Prod Supt Lyons & Logan 1500 Beck Bldg, Shreveport, La ABERCROMBIE, Bolling A (M 60) Mgr Product Planning Axelson-Garrett PO Box 2427, Longview, Tex ABERCROMBIE, C T (160) Prod Engr Cities Ser Petr Co Box 472, Brownfield, Tex ABERCROMBIE, H L Jr (J 55) Prod Engr Mobil Oil Co Room 1800 Gr PI Life Bldg, Lubbock, Tex ABERCROMBIE, Robert (J 57) Prod Engr Mobil Oil Co PO Box 1770 Shreveport, La ABERG, Richard S (M 57) Area Prod Geol Shell Oil Co of Canada, Box 100 Calgary, Alta, Canada]

Jan 1, 1961

By M. M., Fine

In a laboratory study of grinding and classification' of silica sand, a satisfactory means of producing the medium-fine specification sand desired by producers of flint-glass containers was developed. The best procedure consisted of ball-mill grinding and double classification, which gave a properly sized sand containing less iron than the feed.

Jan 1, 1950

By M. C. Manderson

The sharp drop in world phosphate demand that took place in 1975 due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1979

By AIME AIME

THE following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1903, have been withheld from publication until now, in order to make them as accurate and complete as possible. They will be published in Volume XXXV. of the Transactions in their proper place at the end of the said Annual Report. Franklin Ballou was born in Pittsburg, Pa., May 29, 1845. He was the son of an old resident, Arthur Ballou, a manufacturer and wholesale dealer in vinegar. In early youth Franklin attended the Western University of Pittsburg, but left school at the age of 16 to become book-keeper for his father, upon whose retirement from business, in 1868, he associated himself with Walter C. Childs, of Pittsburg, in the manufac¬ture of furnace-grates and asbestos-cement for blast-furnaces. This firm was known as W. C. Childs & Co., and did a success¬ful business for several years. In 1869 Mr. Ballou married Miss May S. Wilson, daughter of Judge Wilson, of Lewistown, Pa. In 1876 he spent several months traveling in the West and studying the mining industry, which greatly interested him. In consequence of this journey, he wound up his business in Pittsburg and removed in 1877 to Georgetown, Colo., where for several years he conducted a sampling-works, and built up an extensive business as an agent for the sale of ores, besides engaging to some extent in mining enterprises. , It is said that he controlled at one time about one-eighth of the output of the Leadville mines. In the early 80's, he became Vice-President and General Manager of the Bimetallic Smelter at Leadville, of which Mr. David H. Moflat was the principal owner. This was practically the first successful demonstration of pyritic smelting in Colorado. Upon the sale of the works in 1897 to the American Smelting and Refining Co., Mr. Ballou retired

Jan 1, 1905

By AIME AIME

PLANS are now well advanced for the joint meeting of the Institute and over a dozen other engineering societies in Chicago during the week beginning June 26: Engineers' Week at A Century of Progress. All engineers planning to visit the Fair will find it to their advantage to be present at this time so far as the Chicago attractions are concerned, and Eastern members will also have the advantage of special transportation arrangements on June 24 and 25. The tentative program is given at the bottom of the next page. Monday morning, June 26, will be reserved for registration of members and guests and the Woman's Auxiliary at the Stevens Hotel, where special rooms will be provided. A luncheon will also be served there, and in the afternoon, a technical session on nonmetallics. Instead of having the big family dinner that evening at the Stevens, as at first proposed, the local committee has planned to have it at the Fair Grounds, where special facilities have been arranged. A meeting of the Board of Directors and a few invited guests will precede the dinner. All members and guests are likely to be interested in visiting the Museum of Science and Industry, so that will be the sole event on the program for Tuesday morning, June 27. The big attraction there at present is the model coal mine, the first operative coal mine ever built for exhibit purposes. It is based on the Deutsches Museum mine at Munich, but goes far beyond that in realism, and takes the visitor on an extended tour underground. It shows him in half an hour more types of modern mining machinery and coal geology than he would be likely to see in a week's underground study in the coal fields. The Institute members will be the first group to go through this mine.

Jan 1, 1933

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

At the meeting of the Board of Directors of the Institute on Jan. 26, 1917, the following actions were taken: Messrs. A. C. Clark, Lawrence Addicks and G. D. Van Arsdale were appointed Tellers to count ballots for Officers and Directors. Messrs. T. T. Read, V. S. Harper, and. E. J. Hall were appointed Tellers to count ballots on revised spelling. The Finance Committee's audit for the year 1916 was approved and ordered filed. The Report of the Finance Committee upon the method of raising this Institute's share of the deficit on the additions to the building was approved and accepted. Upon the recommendation of the Secretary, increases in the salaries of some of the employees were approved. The St. Louis Section received an appropriation of $200 for the year 1917. The Columbia Section received an appropriation of $150 for the year 1917. The Montana Section received an appropriation of $100 for the year 1917. The Colorado Section received an appropriation of $175 for the year 1917. The Utah Section received an appropriation of $125 for the year 1917. The Puget Sound Section received a set of Transactions in standard binding. The International Engineering Congress received a loan of $300 until the Congress can realize upon some of its assets.

Jan 3, 1917

CONTENTS PAGE BAIN, EDGAR C.-The Nature of Martensite. Discussed by Ancel St. John, Henry S. Rawdon, Jerome Alexander, Howard Scott 1 FEILD, ALEXANDER L.-Effect of Zirconium on Hot-rolling Properties of High-sulfur Steels and the Occurrence of Zirconium Sulfide. Discussed by Beram D. Saklatwalla, Bradley. Stoughton, Andrew M'Cance, George F. Comstock, Alexander L. Feild 12 SAUVEUR, ALBERT and KRIVOBOK, V. N.-Use of Sodium Picrate in Revealing Dendritic Segregation in Iron Alloys. Discussed by George F. Comstock, John H. Hall 17 KINNEY, C. L., JR.-Economic Significance of Metalloids in Basic Pig Iron in Basil Open-hearth Practice. Discussed by V. J. Pazzetti, George B. Waterhouse, C. L. Kinney, Jr 19 NEAD, J. H.-Absorption of Sulfur from Producer Gas in Open-hearth Furnaces.. Discussed by George B. Waterhouse, C. L. Kinney, Jr 26 PRIESTLY, WILLIAM J.-Effect on Steel of Variations in Rate of Cooling in Ingot Molds. Discussed by Emil Gathmann, Paul E. McKinney, George A. Dornin. 27 MONYPENNY, JOHN H. G.-Stainless Steel, with Particular Reference to the Milder Varieties (Stainless Iron). Discussed by P. A. E.-Armstrong, Beram D. Saklatwalla 33 ROYSTER, P. H., and JOSEPH, T. L.-Effect of Coke Combustibility on Stock Descent in Blast Furnaces. Discussed by Ralph H. Sweetser,. Richard Franchot, Sidney Cornell, T. L. Joseph 41 DAVIS, F. W., and BOLE, G. A.-Observations on Requirements of Refractories for Open Hearth. Discussed by C. L. Kinney, Jr., L. F. Reinartz, P. E. McKinney 46

Jan 5, 1924