Search Documents

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson's3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970

By K. S. TWITCHEEL

THE different lines leading out from the vocation of a mining engineer are,' perhaps, the most' varied of all the professions. The expedition sent by Charles R. Crane of New York 'as a gift to the Imam Yahia, king of the Yemen, Arabia, was probably unique. Mr. Crane made a visit, in January,1927, to the Imam Yahia at Sanaa, capital of the Yemen. He was received with the utmost cordiality and respect, as his friend- . ship for the ,Arab world is famous; He was 'greatly impressed by the desire of the Imam to develop his country. The Imam stated that he had heard that there were minerals in his country and that he would like to secure engineers to advise him about them and other natural resources.. This seemed such a practical idea, and so greatly appealed to Mr. crane, that he offered to furnish an engineering 'expedition. Naturally the Imam gratefully accepted. This expedition was to study (as far as possible in 'the limited time) the natural resources of the ,Yemen, advise the Imam of what these consisted, and make suggestions regarding the most practical methods for their development. As agriculture is always such a fundamental part of a country's wealth, I first went to Indio, California, to study water-well drilling and the date industry, and eventually arrived at Hodeidah, the principal Yemen seaport, on Oct. 21, 1927.

Jan 1, 1929

By P. Linehan, J. F. Wiss

Vibration and air blast noise from blasting were evaluated during a research program sponsored by the US Bureau of Mines. Blast variables were studied wing small scale model (SCM) tests to evaluate specific variables as well as interactive effects, followed by experiments with production blasts at the surface coal mines. Experimental data showed that the primary variables affecting the ground vibration amplitude are the charge weight per delay and the length of delay interval. Blast variables having a significant effect on the overpressure amplitude include the charge weight per delay, the length of delay, burden and spacing, stemming amount and type, direction of initiation, charge depth, and amount of detonating cord and cover.

Jan 1, 1983

By Kenneth C. Vincent, A. M. Gaudin

TEN years ago Taggart, Taylor and Ince1 described a workable, convenient apparatus for the measurement of contact angles between cleaved, ground or polished particles and captive bubbles. Wark and Cox2 and Wark and Sutherland3 have done an immense amount of experimental work with this apparatus. Their work has had as principal object the determination of "contact curves." Contact curves are cartesian charts in which pH (or some other variable) is plotted against quantity of modifying agent. The rectangular area is broken into two or more curvilinear areas separated by the contact curve. The curve indicates that a sharp demarcation exists between conditions that bring about sticking of particles to bubbles and conditions that do not produce sticking. The type curve appears in the TRANSACTIONS as Fig. 1, page 248, volume 112. Wark and Cox offer data to show that the contact angle has a value determined by and characteristic of the agent used. Wark and Cox also make the statement that they believe this value is independent of concentration (ref. 2a, p. 209). They say: It is suspected that, given sufficient time and provided that there are no disturbing factors, the full ethyl xanthate angle (corresponding to a complete xanthate film) would be obtained in every case where contact occurs. Such a conclusion, if correct, would tend to substantiate the hypothesis of flotation collection by metathesis championed by Taggart and his associates4-8 and would argue against the adsorption hypothesis now adopted by Wark7 and by one of us.8 However, the data of Wark and Cox do not bear out the conclusion that there is a sharp passage from conditions of contact to conditions of noncontact. Rather, they indicate the existence of a transition zone of reagent concentration across which the contact angle varies with changes in reagent concentration from zero to a value near the maximum. This may be seen, for example, from Fig. 195 in the new text by one of us (ref. 8, p. 380), which presents the data of Wark and Cox in graphical form. The object of this study has been to explore the nature of the transition from conditions of contact to conditions of noncontact. The data of Wark and Cox to which reference has been made as showing that a gradual transition exists are marred by the fact that the region of critical-agent concentration is at an extremely small concentration. This condition suggests that diffusion may have played such a preponderant role that equilibrium was not reached within the time alloted. In the Wark and Cox data, the critical concentration was at about one part of xanthate per million parts of water. To form a monolayer of xanthate on the mineral surface would therefore require depletion of xanthate in the liquid to a depth of the order of

Jan 1, 1940

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By J. T., Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas on the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has- also developed very rapidly recently and the various processes to which metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles.

Jan 1, 1927

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By J. D. Cooner

Since my working life of 32 yr has been spent in and about the anthracite mines of the Hudson Coal Co., and the previous 4 yr in a college school of mines, I can write best about the safety program of a coal mining company. However, most of the suggestions, statements and practices mentioned herein are applicable to the members of a safety organization and program of almost any industry. It is realized that industrial officials actually interested in real safety work are fully acquainted with the requirements of a practical safety program. Therefore, for such persons there may be nothing new in this paper. The Hudson Coal Co. of Scranton, Pa., employs 7000 men and produces 5,000,000 tons of anthracite annually at nine collieries scattered for a distance of 40 miles throughout the Lackawanna and Wyoming valleys of northeastern Pennsylvania. For the past 17 yr of the above mentioned 32, I have been engaged in safety work as a safety inspector, assistant mine superintendent, and at present the safety engineer. I have also had the privilege of visiting coal and metal mines in other parts of the United States and Canada. We Americans are the most careless people in the world. If any one doubts this statement why are 100,000 of our people killed accidentally annually? Or why during the almost four years we were engaged in World War II were more of our people killed accidentally at home than were killed in our army, navy, marine corps, coast guard, and other services during the same period? We are careless everywhere— in our homes, on the highway, at work and at play. The purpose of this paper is to outline the requisites of a safety department and its program to stop the accidents occurring to employees at work in mines or industrial plants. The first requisite for a safety program is that the management must be convinced of the need and value of a real safety program. By "management" is meant each department head from the president down. Otherwise a good safety department with a good safety program will not succeed because it will not have the proper personnel and equipment to work with, its rules and regulations will not be enforced, and the members of the safety department will be belittled in the eyes of most of the workmen and supervisors. Next, a safety engineer and his inspectors should have worked in the production end of the mines as workmen and also in an official capacity. They are then in a position to have practical and first hand knowledge of the accident hazards of the industry, how to prevent them, and in general the problems of both the workmen and officials. Some men are appointed as safety inspectors when they are physically unable to carry on as mine officials. Such men may know the safety end of the industry and even be safety-conscious, but if they are physically unable to be mine officials they are also physically unable to be safety inspectors, as a safety inspector in our mines must walk from 2 to 4 miles on each daily inspection and visit each working

Jan 1, 1949

By Beverley S. Randolph

The coal-measures of George's Creek coal-region, in Maryland, lie in a comparatively flat synclinal basin, about 4 miles wide. The dip of the measures is, in places near the edge of the basin, as much as 20 feet in 100. The Pittsburgh seam, known locally as the " Big Vein," is the only seam worked at the present time. Ocean No. 3, one of the large mines of the Consolidation Coal Company, has its opening on the outcrop of the Pittsburgh seam, in a ravine which cuts into this seam to such an extent as to bring this opening to within a mile of the axis of the basin. After working all the coal to the rise of this point, the mine was further developed by extending a slope down the dip of the seam, making such an angle with the line of greatest dip as to give a grade varying from 1 to 10 per cent., down which the empty cars carry a rope from a single-drum winding-engine. The coal was worked from each side of this slope in successive Iifts during its progress. From the top of the slope, for a distance of 4000 feet to the fourth lift, the " make " of water is drained by gravity through a heading into the adjoining mine. Below this point the water was pumped into this same heading, at the fourth lift, from which point, as before mentioned, it flowed by gravity.

Jan 1, 1895

* The greatest and richest iron ore body in the world was discovered by U. S. Steel in Venezuela in April 1947, and is disclosed for the first time in this issue (p. 178), One solid mountain of ore, Cerro Bolivar, will furnish more tonnage than the famous Hull Rust pit at Superior has, or can produce. Total resources are on the order of 2 billion tons plus. Big Steel is now moving with great speed on construction to bring out this ore, and 10 million tons are scheduled for shipment into Baltimore and Birmingham by late 1952. This ore will arrive at, Pittsburgh at a price lower than present natural ores from Superior. The Venezuelan properties will be completely mechanized. •U. S. Steel and independent companies are embarking on a taconite beneficiation program of tremendous proportions, which must be speeded to completion in the 1950's (see p. 185). By 1960 over $l.2 billion dollars will be spent on Venezuela, taconite, and Labrador to solve the United States iron ore crisis. In addition, U. S. Steel will spend another $300 million plus for a new steel mill at Trenton, N. J., before 1955. •The Deister Concentrator Co. gave $500 to the 1950 Coal Division Scholarship Fund. •Howard N. Eavenson, in analyzing the bituminous coal situation (see p. 193), suggests that anti-trust laws be extended to labor unions, disinterested trustees to administer pension funds, begin pension funds now and stop the collection of all "check-offs" for union dues or funds. •Minerals and metals worth 13.9 million dollars were produced in the United States in 1949, Secretary of the Interior Oscar L. Chapman announced. Although this value was 11 pct less than in 1948, it was the second greatest in history. Nonmetallics was the only major group that in 1949 equaled the 1948 production high. Mineral fuels decreased 12 pct and metals 15 pct. • Prospects for making gas from coal are seen to be unattractive by the Pittsburgh Consolidated Coal Co. because the success of operation depends on price and supply of coal which presently are not attractive. The company has shut down its gasification plant at Library, Pa. * Economic prospects for the immediate future in the United States are good and business probably will continue at its present high levels throughout at least the early part of 1950, Secretary of Commerce Charles Sawyer said in his year-end report to the White House based on his personal survey of business conditions. •A 467-ft well 34 miles north of Rock Springs, Southwestern Wyoming, is said to be flowing a 5 pct solution of nearly pure trona (sodium carbonate) at the rate of 10,000 barrels a day. Trona, natural soda ash, is mined for the chemical trade at Searles Lake, Calif., and from about 1500 ft underground near Green River, Wyo., and has been in short supply. •The AEC is "very much interested" in a discovery of radioactive material that has been made in Baraga County bordering Lake Superior in the Upper Peninsula of Michigan, reported F. G. Pardee, Michigan State mining engineer. The material has been identified as uranium oxide in the form of pitchblende or uraninite. The discovery, made by a geologist of the Jones & Laughlin Ore Co., is the only instance in which the commission has certified samples of Michigan rock.

Jan 2, 1950

By Hans Haalck

PRACTICAL or applied geophysics-as we designate the border region between physics and geophysics on one hand and practical geology on the other-has as its object the application of physical or geophysical methods of investigation to problems of practical geology. Its field of operation comprises all methods of physical measurement that are used in the problem of determining, from the geophysical influences of the subsoil that can be measured at the surface of the earth, the special characteristics of the association of strata, faults, etc., to detect the presence of deposits and to investigate underground structures. It therefore represents an aid, a physical method of research in practical geology, and is inseparably connected with geological studies; for this reason, it is also called geophysical prospecting. Formerly research methods of practical geology were based on observation exclusively: first, on the observation of the strata and formations at accessible parts of the surface of the earth, especially in shafts, borings and mines if such were available; then on the observation of the tectonic conditions in so far as these were already known at places directly visible; and finally, by estimation of the importance of formations of the terrane. Later, there were added in special cases, analytical chemical crystallo-graphical, petrographical and similar investigations of rock samples which were taken from the places under consideration. The knowledge thus obtained is of value and is expanded by hypotheses and constructions that are supported by geological theories of origin and by laws of the sequence of formations and rock systems, which are based on long experience.

Jan 1, 1928

By W. Lawrence Austin

It has been suggested to me that some data, bearing on the treatment of silver ores in Southern Arizona, would be in accord with the objects of the present meeting. I have, therefore, made a few notes, gathered from practical experience at some of the best known works of that district. Presuming the general arrangement of a silver mill to be familiar to members, the subject having been repeatedly brought to the notice of the Institute, it is my aim in the following description of the modus operandi at the different mills to which I would invite your attention, to give simply such salient points of the apparatus as have a direct bearing upon results, together with the cost of materials, labor, etc. I have gone somewhat deeply into detail in my descriptions of machinery, thinking that possibly some of our members engaged in this branch of the profession might find something of interest among them. In an industry such as silver milling, where the various works are scattered over a vast extent of territory, and the conditions under which results are obtained are subject to the greatest variations, it is essential to go into rather minute details in describing plants, processes, etc., in order to afford a clear idea of the operations. Not only should results be given, but also the means by which such are attained. The milleralogical and chemical constituents of the ore, and its physical properties, throw a flood of light upon the success or failure of a process Figures representing totals I have subdivided as much as possible, so that the cost per ton for labor, castings, chemicals, etc., are apparent. Unless all these Factors are known, no accurate comparison can be drawn, since in this branch of metallurgy, more perhaps than in others, the weakness of any one link in the chain of operations demoralizes the remainder. That it costs $10 to mill in one

Jan 1, 1883

By James Hall

A geological map of a State involves very much, and its pre sentation to the public incurs grave responsibilities. It has been for a long time my earnest desire to bring out and place before the pub lic a geological map of New York which might be creditable to the State and worthy of a place among her scientific publications. We have done much for the advancement of geological science in this State—very much, and in many directions—but unfortunately, this feature, which should have been made the basis of all our work, has been too long neglected and delayed. For twenty-five years I have been laboring and looking forward to this consummation. I have recorded the field-work, systematic and desultory, upon such maps as were available for this use; and notwithstanding their imperfec tion, I have been able to transfer this recorded information to a more perfect base, which it is hoped will be completed during the early months of the next year. In 1883 I had combined, upon a small map of the State, the in formation which we possessed at that time, and communicated the same with my annual report to the Legislature. The report mas published in the regular course, but the special appropriation made for the map was vetoed by the Governor. Not discouraged by this untoward and unexpected circumstance, I continued my work, and made every effort to render the map more complete, preparatory to its communication with the next annual report. I brought together all the information within my reach, whether published or unpublished, reviewing and revising, as far as practicable, the work done by myself and assistants in southern and southeastern New York.

Jan 1, 1893

By B. Alexander, G. Derge W. Peifer

This is part of a research project in the Metals Research Laboratory of Carnegie Institute of Technology, sponsored by the Carnegie-Illinois Steel Corporation. In organizing our program it became apparent that the problem of analyzing molten steel for hydrogen must be divided into two parts: (I) the correct analysis of a given sample, and (2) the correct sampling of the bath. Emphasis has been placed upon these divisions in the order named because methods of sampling cannot be evaluated until a satisfactory method of analysis is available. Vacuum fusion was selected from the list of possible analytical methods because it seemed to us to offer the best possibilities for giving rapid, accurate results on solid steel samples. A number of objections have been raised against this method as usually practiced. We have sought to meet some of these by proper design of the apparatus. Experiments will be described which show that others are not valid. In the conventional apparatus the sample is held under high vacuum for a period of several hours before it is actually analyzed and one might expect considerable hydrogen to escape during this period. We have provided a means of introducing the sample to the vacuum just before analysis. Another difficulty has been that the entire apparatus has been designed primarily for the purpose of analyzing for oxygen, which constitutes upward of go per cent of the total gases evolved from the sample The volume and pressure measurements have therefore been insensitive to the relatively small amounts of hydrogen present. This difficulty obviously can be taken into account in any apparatus designed especially for the amounts of hydrogen expected. Analysis in Vacuum-fusion Apparatus A number of experiments were carried out to determine the importance of several factors that have been stated as possible sources of error or uncertainty in vacuum-fusion analysis for hydrogen; namely, that hot graphite will absorb some of the gases, that metal vapor will cause discrepancies, and that low results may be obtained as a result of the water vapor (produced by the oxidation of the hydrogen) dissolving in the butyl phthalate of the manometer, or that the blanks obtained from the apparatus are so great as to make the method inaccurate. The experiments also checked on the accuracy and feasibility of using differential freezing as a method of gas analysis in a vacuum-fusion apparatus.

Jan 1, 1945

NORTH AMERICA ALASKA Anchorage,-Ames, M. B. Culver, H. W. Fiedler, H. L. Fox, E. F. Gallemore, W. A. Kreitlow, E. J. Layfield, R. A. Saarela, L. H. Strandberg. H. Candle,-Bobbins, J. S. College.-Fackler, W. C. Joesting, H. R. Swift. R. E. "Wilcox, H. G.. Crooked Creek-Lyman. R. F. Fairbanks.-Beistline, E. H. CANADA Canadian Army Overseas,¬ Ball, H. D. Brides, C. Butterill. H. J. M. Ladner, F. E. Lane, H. C. Millar, R'. A. Murchison, R. G. Passow, F. M. ALBERTA Calgary-Allen, R. E. de Hart. J. B. Dingman, C. W. Furnical. G. H. Gray, J. G.

Jan 1, 1943

By J. M. Dumore

If in a vertical, downward miscible displacement, the transition zone between the displacing and displaced fluids is neglected, a criterion for stable displacement can be obtained by considering a small hypothetical protrusion of one of the fluids into the other. This criterion leads to the definition of the well-known critical rate, uc = kg p/p. The consideration is further extended by taking into account the transition zone that develops as a result of diffusion and mixing. A generalization of the previous criterion leads to the definition of another characteristic rate, the stable rate, which in actual miscible drives will be less than the critical rate. In such drives, the entire transition zone is stable at rates less than the stable rate. At rates between the stable and critical rates, the displacement is only partly stable, i.e. part of the transition zone adjacent to the displaced fluid is in an unstable position. From that part of the transition zone viscous lingers will develop. At rates greater than the critical rate the entire displacement is unstable and viscous lingers will develop more strongly. Results of laboratory experiments are in agreement with the expected behavior based on the theoretically deduced stability of the displacement. INTRODUCTION The simplest form of miscible drive in an oil-bearing formation is the injection of a fluid that is completely miscible* with the oil under reservoir conditions. In general, such a fluid, a solvent for example, is less dense and less viscous than the oil present in the formation. If it is injected into a horizontal homogeneous layer, gravitational forces will lead to the formation of a gravity tongue of solvent in the upper part of the layer and the adverse solvent-oil viscosity ratio will cause viscous fingers to develop. If, however, the solvent is injected up-structure into ,a dipping layer, gravity has a favorable effect, because it tends to keep the less dense solvent up-structure. Tongue formation and viscous fingering are consequently reduced and it is even possible that they will be suppressed completely. Viscous fingering and gravity tonguing are the consequences of the instability of the displacement. A stable displacement cannot result in growing viscous fingers and/or growing gravity tongues. Since large amounts of oil can be bypassed if there is viscous fingering and/or gravity tonguing, the stability of a miscible drive is very important with respect to the recovery efficiency of the drive. The stability is of particular importance in miscible-slug drives, as it determines how quickly the miscible slug between the displaced and displacing fluids will be distorted and broken up, after which the drive is no longer completely miscible. Stability is thus a most important factor in determining the success of a miscible drive, and it is considered that the aspects of stability considered in this paper will make a useful contribution to existing theories. Consideration is given only to vertical downward displacements, in which no gravity tongues can develop and which are therefore simpler than downward displacements in sloping layers. THEORY CRITERION FOR STABLE DISPLACEMENT Let us consider a vertical column of a homogeneous permeable medium saturated with oil. A solvent less dense and less viscous than the oil is injected at the top of the column at a constant rate; in the column the velocities of oil and solvent are assumed to be uniform. Diffusion and mixing of oil and solvent will at first be neglected, i.e. we assume that solvent and oil are divided by a sharp interface. An additional assumption is that the interface is horizontal. Continuity of pressures exists at the interface, because no capillary forces are present between the two miscible fluids. Consequently, at the interface (Z = I)):** Ps = Po - P-where Ps is the pressure at the solvent side and

Jan 1, 1965

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for Predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale); Condition C (Rolling Sandstone with Shale in Pockets); and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1979