Search Documents

By Kent W. Pilz

Wet dust suppression can be achieved by 1) confinement of the dust within the dust producing area with a curtain of moisture, 2) wetting of the dust by direct contact between the particles and droplets of moisture or 3) the formation of agglomerates too heavy to remain airborne, or too heavy to become airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid; however, it is not as effective for dust suppression as when small percentages of specially formulated dust control compounds are blended with it. Performance of dust control com pounds is related to surface active agents and surface activity. In all liquids there is an attractive force between molecules which varies inversely as the sixth power of the distance between molecules. Thus, in the liquid phase where molecules are crowded together, the intermolecular forces are powerful; whereas in the liquid-vapor phase where the molecules are relatively far apart, these forces diminish rapidly. In the body of a fluid there is an uneven distribution of forces resulting in an inward pull called surface tension. The force which keeps two surfaces apart or causes them to coalesce is termed interfacial tension. Fluids of high surface tension exhibit poor wetting, spreading and penetrating qualities. Water has the unusually high surface tension of 72.75 dynes per cm at 20°C.

Jan 7, 1972

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By AUGUSTUS J. MONKS, Norman L. Weiss

THE Santa Barbara Unit of the Compania Minera Asarco, of which the San Diego mill is a part, is in the Parral District of southern Chihuahua. Although the concentration of sulfide ores has been practised in Santa Barbara since 1900, the San Diego mill, completed in 1921, was the first plant in northern Mexico to attempt the treatment of oxidized lead ores. From the milling point of view the many ores that have been treated at San Diego are very similar, the differences among them being rather of degree than type. Since 1921 the number of ores from different sources treated simultaneously has varied from four to eleven; in no case have any distinctive characteristics warranted the separate treatment of any of these. The zone of oxidation, source of the ores milled at San Diego, extends to a depth of 300 to 400 ft. below the surface. These ores carry more gold and less silver, lead, copper, and zinc than the underlying sulfide ores; the gangue minerals appear comparatively unchanged by oxidation and leaching. Lead occurs in diverse minerals, chiefly in cerussite, galena, and angle-site, the proportion of the lead in galena varying considerably in the different mines. An average of the feed to the mill would show the following approximate distribution of the lead content:

Jan 1, 1930

By Walter White

THE measurement of the reading of a thermoelement is the measurement of an electromotive force extraordinarily small compared to those generally used in commercial work. Of the various possible methods of measuring such a quantity, the most advantageous is always a delicate galvanometer. Since a galvanometer measures current, it is necessary to adopt some scheme by which its current reading shall indicate electromotive force. There are two general methods of doing this. One is to use the delicate galvanometer as a "direct reader," that is, to let the electromotive force of the thermoelement furnish the power and produce the current measured. If the resistance is constant the reading will, after a suitable calibration, give the electromotive force of the thermoelement which, by means of a table or of a suitable scale in the galvanometer itself, will FIG. 1.-SIMPLIFIED POTENTIOMETER. POTENTIAL DROP ACROSS THE PART PIN or CIRCUIT OF BULL CELL BALANCES THAT OF THERMOELEMENT TC WHEN GALVANOMETER G READS ZERO. give the temperature. The other method, that of the potentiometer, is to balance the electromotive force of the thermoelement by means of another electromotive force, using the galvanometer to tell when the balance is made. The usual way of getting this other electromotive force is to have a battery, the "bull" cell, send a current through a series of resistances, which 'may in a special case be the resistance of a single wire. The fall of potential along this circuit will then, by Ohm's Law, be proportional to the resistance; the potential difference between any two points, proportional to the resistance between the two points. This is represented in Fig. 1, where M and N are the two points in the circuit AZ of the battery. If M or N, or both, is movable so that the resistance

Jan 9, 1919

By W. C. MENDENHALL

THE problem of maintaining the mining industry is two-fold; finding new supplies in the face of increasing difficulties, and making such advances in the arts of extraction and preparation as to use supplies of lower grade. Progress in mining and reduction methods and in transportation makes ore today of that which was waste yesterday. These are the fields of the metallurgists and the transportation engineers. The geologists and mining engineers must work together on the problem of ore finding. As the old prospector fades from the scene, men with equal hardihood and patience and equal power to meet the physical obstacles which confront the seeker after ore, must take his place, armed with all that has been learned from human experience about the causes, the controlling conditions, the indications, and hiding places of the metals. Such a seeker is dealing with some of the most complex and obscure of natural phenomena. In nature's laboratory, tremendous forces are at work. Tempera-

Jan 1, 1926

By F. W. Jessen, R. W. Durie

The development in the laboratory of mall salt cavities illustrated that the rate at which salt dissolved was affected by the rate at which fresh water was injected into the cavity. Experiments carried out with small salt cores indicated, however, that the rate of salt removal with forced convection was not significantly different from that with natural convection, provided the flow was in the laminar range. The rate of salt removal was apparently controlled by the water salinity, which was indirectly determined by the rate at which fresh water was injected. With turbulent flow at the salt surface, the rate of salt removal could be increased several-fold with the same salinity in the cavity. A quantitative evaluation of the rate of salt removal under natural convection was attempted by using techniques developed for the analogous heat convection system. The values of the rate of salt removal obtained experimentally were considerably greater than the calculated values due to surface irregularities. To determine the effect of these irregularities, the rate of salt removal was found for a smooth surface by experimentally determining the rate of salt removal as an irregular surface developed and then extrapolating this trend back to initial time. Excellent agreement between the experimental and calculated values then were obtained. INTRODUCTION Underground cavities leached from massive salt formations have been used extensively for many years for storing LPG products. The development techniques for storing methane gases in the liquid state at a low temperature leads to speculation that underground salt cavities of controlled geometry may be quite important in this field. In any case, the increasing number of salt cavities used for storage indicates an impending need for a better knowledge of the washing process to efficiently develop maximum storage volumes within specified regions. It is the purpose of this paper to discuss some aspects of -the mechanism of the dissolution of salt in the formation of cavities of controlled geometry. Although no attempt is made to resolve the problems that may be associated with the storage of methane in the liquid state in salt formations, the fact that salt cavities can be formed at reasonable cost would appear to justify investigation in this direction. Further, underground cavities have the advantage of allowing storage at higher pressures (and hence higher temperatures) than surface installations. Although the thermal conductivity of salt is somewhat higher than frozen earths, 0.017 cal/(sec) (cm)(c) for salt at 32F vs 0.005 cal/(sec) (cm) () for ice at this temperature, this disadvantage is offset by the higher storage temperature in underground cavities. For example, at atmospheric pressure, the temperature of liquid methane would be —258F. In a storage cavity at 2,000 ft, the pressure would be approximately 1,000 psia, which would allow a storage temperature of -9OF. The formation temperature would be roughly 110F at this depth, hence the total temperature differential would be 200F. Under surface storage conditions the corresponding temperature difference would be some 333 F (75 F + 258 F). The results of this difference can be compared more readily by substituting the appropriate values of thermal conductivity, temperature difference, heat capacity and density into the solution of the diffusion equation for the unsteady linear conduction of heat. For the underground salt storage, the heat flux is 15cal/(sec) (sq cm), where t is the time in seconds from the initiation of the cooling. For the surface system, and using the thermal properties of ice at the average temperature, the corresponding figure is 21cal/(sec) (sq cm). Hence, the heat losses through ice under surface conditions would be some 30 per cent higher than the underground salt storage. This ratio would vary, considerablv. Of course, for other conditions, but it indicates that an advantage over surface facilities may be obtained by storage in underground salt cavities.

Jan 1, 1965

By H. A. Bauman, T. S. Spicer, C. C. Wright

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 2, 1950

By E. C. Houston

The phosphate ores mined in middle Tennessee typically consist of granular rock phosphate particles disseminated in a clayey matrix. In the TVA plant near Columbia, Tenn., the phosphate ore is mined, made into a slurry with the addition of a small amount of sodium hydroxide as dispersant, and treated in a hydroseparator to remove minus 10 micron material. The hydro-separator underflow, comprising a rough concentrate, is transported by pipeline to the plant; the hydro-separator overflow, comprising a tailing, is flocculated by addition of calcium sulphate and is discharged to settling ponds at a rate of about 1400 gpm. Sedimentation in the ponds produces a clarified effluent, which may be recycled for use as process water or discharged to surface drainage. This method of tailing treatment is not entirely satisfactory since poor sedimentation characteristics of the tailing result in poor ultimate utilization of pond storage volume.

Jan 1, 1949

By C. G. Rhodes

A technique for producing etch pits in uranium monocarbide has been developed. The pits, which are assumed to be associated with dislocations, appear individually and as arrays delineating sub-boundaries, as seen in Fig. 1. The samples used were single crystals prepared by the technique described by Nadler.* Uranium

Jan 1, 1963

By Joseph Gurland

EVERAL carbide-cobalt compositions were pre-^-5 pared for the purpose of determining the transverse rupture strength of various carbide-binder systems. The binder content was held at 10 and 37 volume pct Co, so as to be representative of low and high bjnder compositions. The carbides used, WC, Tic, TaC, CbC, VC and ZrC, were selected on the basis of availability, knowledge of their properties, and small solid solubilities in the binder metal at room temperature. The methods of preparation and carbon analysis of the carbides are summarized in Table I. The carbides with cobalt added were ball milled, pressed, and sintered. vacuum sintering was used throughout, except for the WC-Cs alloys, which were sintered in hydrogen. The sintering temperatures ranged from 2500" to 2750°F for the low binder alloys and from 2300" to 2550°F for the high binder alloys. Compositions and properties of the sintered com- pacts are presented in Table 11. For the transverse rupture strength, the average and range of the five best samples of each alloy are listed. Discrepancies between the actual and theoretical densities are attributed to carbon deficiencies in some samples. The theoretical densities were calculated by assuming mixtures of carbides of stoichiometric compositions and cobalt. Representative microstructures are shown in Figs. 1 to 6. The porosity was A-2 or better' in all alloys except those with ZrC. A grain size of about 3 p was

Jan 1, 1958

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By AIME AIME

INDUSTRIAL Pittsburgh, the center of the coal and iron and steel industry of the world, was host to the Coal Division at its Fall Meeting held there on Oct. 21 and 22 at the William Penn Hotel. The past year has witnessed remarkable progress in new methods of mining and burning of coal and many of the papers on the program discussed these developments. Nearly 100 had registered at the time of the first session on Wednesday morning and this number increased to 168 on Thursday. Owing to the large number of papers on the program, eighteen in all, it was necessary to hold group meetings on Thursday morning, with a capacity attendance at each meeting. . Chairman McAuliffe was on hand early Wednesday morning to open the meeting. George Otis Smith, representing President Lovejoy, came over from Cleveland where he attended the meetings of the Institute of Metals Division. Secretary Parsons arrived later from Cleveland and spent the whole morning with the executive committee of the Division. Doctor Smith, Secretary Parsons, and J. T. Breunich were the official representatives from Institute headquarters.

Jan 1, 1936

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

Bellows Connector Fabricated of chemically inert Teflon, the new bellows type connector has many pipe line applications where vibration, expansion and electrolysis exist in the handling of corrosive liquids or gases and solvents. The new connector is electrically non-conductive, flexible even at 94°F and as strong as 480°F as at 70°F, according to the manufacturer. This bellows connector serves as a [ ] vibration dampener as well as an expansion joint and connects misaligned couplings and insulates flanges electrically. End flanges of the joint are French-type envelope gaskets made integral with the joint for easy assembly between companion flanges and a tight, leak-proof seal on installation. Circle No. 1

Jan 1, 1952

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By Clyde E. Williams

MUCH has been said recently concerning the depletion of the Lake Superior iron ore re- serves. Estimates given indicate a total life of the present known reserves of twenty to thirty years. Some argue that there is no need to concern ourselves about the possible depletion of the Lake Superior iron ore supply because foreign ores can be brought in to this country at a lower price than rich agglomerated ore can be produced from the lean domestic ores. Some fear, as a result of this, a displacement of the steel business from present districts to the Atlantic seaboard. Others show that foreign ores will be brought to interior points via the projected Great Lakes-St. Lawrence waterway. Others believe that the South, given better freight rates, will extend its iron and steel market into northern territory.

Jan 1, 1931

[ ]

Jan 1, 1938

By H. J. Booss

THERE is a considerable lack of data on thermody-namic properties of hard-metal alloys. Only two papers 1,2 give mean values of specific heat in an unknown temperature range; more recently the author3 gave more detailed information on the mean specific heat in the temperature range from 20" to -190° C.. EXPERIMENTAL 1) Method—Experimental procedure followed a method suggested by Oelsen and coworkers.4 It requires samples of some 100 g of weight. The time of measurement is prolonged (30 min) but one run allows the measurement of a lot of positions on the heat-content curve. Results4 were found to be in good agreement with "best values" given by kelley,5 Kubaschewsky and Evans,6 etal.

Jan 1, 1960

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of March, 1913 BAECHTOLD, CHARLES A., Engr 9G Liberty St., New York, N. Y. BRANTLY, JOHN E., Instructor in Geology Tuscaloosa, Ala. CADDY, JAMES P., Net., ,Lake View & Star, Ltd Fimiston, West. Australia. LONERGAN, PHILIP J., JR., Prof. of Mining, Government University, Peking, China. MCKANNA, EDWIN A., Min. Engr P. 0. Box 834, Oklahoma City, Okla. MACDONALD, ANGUS W., Supt. Labor Dept., Dominion Coal Co., Ltd., 21 Queen St., Sydney, N. S., Canada. TSUBOI, Yoshio, Min. and Met. Engr., Kosaka Mine, Fujita Co., Akita-ken, Japan.

Jan 4, 1913