Search Documents

By J. M. Smith, D. Kunii, P. Adivarahan

Effective thermal conductivities were measured for seven samples of porous rocks through which gases or aqueous salt solution were flowing, parallel and countercurrent to the flow of heat. The results are analyzed in terms of the contributions of the solid and fluid phases to the total energy transfer. The solid contribution for the sandstone samples studied was found to be a Junction of the porosity and an effective thermal conductivity for the solid phase. The fluid contribution was a function of the Peclet number. Based upon the equations presented, the effective conductivity of the system can be estimated from the properties of the fluid, the flow conditions, and the porosity and pore-size distribution of the rock. INTRODUCTION Heat-transfer characteristics of porous media containing fluids are needed for the design and evaluation of thermal methods of petroleum production. The study reported here considers the problem of countercurrent flow of fluid and heat in sandstone rocks, and is a continuation of previous studies concerned with parallel and radial flow of energy and fluid in both rocks517 and beds of fine particles.6,10 In addition to these earlier works, Asaad,1 Kimura,4 Preston,8 Zierfuss and vlietll and waddams9 have reported effective conductivities for systems filled with stagnant fluids. There appears to be no published data on rocks through which fluids are flowing. The purpose of this study was to present such information and, particularly, to investigate the effects of properties of the rock and the flow rate on the results. The rock samples were naturally occurring sandstones from different locations and were similar to petroleum-bearing formations. The properties of the seven samples showing the range in porosities and permeabilities are given in Table 1. The mean pore sizes were calculated from mercury penetration data by averaging the radius with respect to pore volume. The details of this method and comparison with other procedures for estimating 7 are given elsewhere. Four fluids, nitrogen, carbon dioxide, helium and 10 weight per cent sodium-chloride solution were used with each sample. For Bartlesville sandstone, BA-5, runs were made at mean pressures from 15 to 250 psig using nitrogen. The other measurements were carried out at a mean pressure of 100 psig. The maximum temperature range eacountered was 70° to 300°F. The flow rate of fluid ranged from about 1.0 to 130 Ib/(hr)(sq ft), and this corresponded to a modified Reynolds-number range of 5 x 10-4 to 1.0. The variation in Prandtl number was 0.70 to 4.1. EXPERIMENTAL WORK The equipment consisted of apparatus to supply a constant flow of gas, or salt solution, at constant pressure to the bottom of a vertical test section, and metering and flow-regulation apparatus after the test section. The flow of salt solution was

By Paul H. Hunt

MANY MISUNDERSTANDINGS have arisen regarding -Al the purchase by the Government of 24,000,000 oz. of domestically produced silver annually for the next four years at a price of 64 1/2c. to the producer. Some editorials have an¬nounced rather sarcastically that be¬cause of the strong western silver bloc in Congress, the Administration is paying a bonus of approximately $22,000,000 to a few large silver produc¬ers of the West, the amount being figured on the total purchase of about 100,000,000 oz. and the difference between the Government price and the world price for silver. Actually the Government will make a profit on this purchase, due to seigniorage, of something over $60,000,000. The 96,000,000 oz. of silver, for which the producers will receive approximately $62,000,000, will be produced in association with at least $100,000,000 worth of lead, zinc, copper and gold; the greater part of this $162,000,000 worth of metal will be produced at little profit to the mining companies, as will be shown later, because of the low prices for lead, copper and zinc. This amount of money will be spent largely for labor and supplies, thus greatly relieving the national burden of unemployment. Certainly, western mining, in the purchase of this silver, is not victimizing the Federal Government.

Jan 1, 1934

By A. B. Johnson, J. S. Browning

The USBM has developed new and improved physical beneficiation techniques for economically recovering potash minerals from high-clay and low-grade ore from the Permian Basin of New Mexico. With the depletion of the high-grade ores a need for changes in industry's standard methods of recovery is a must. Technology may be improved in the beneficiation of the ore prior to mineral flotation and in brine clarification from the desliming phase to effect a reduction of losses of fine potash and brine in the disposal of the clay slimes. This report summarizes the results of these tests and demonstrates the feasibility of producing products that meet the requirements of the agriculture market, namely, 95% KCl equivalent to 60% K2O with recoveries ranging between 80 and 90%.

Jan 1, 1973

By Edmund C. Pechin

The Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

By J. L. Whitlock

An attached growth aerobic biological treatment process has been developed at Homestake Mining Co.'s Lead operation which not only oxidizes free and complexed cyanides, including the stable iron complexed cyanides, but also thiocyanate, and the oxidation byproduct ammonia. Through the employment of a mutant strain of bacteria which has been gradually and specifically acclimated to the waste, these potential pollutants are mineralized to relatively harmless sulfates, carbonates, and nitrates. The resultant effluent, through toxicological testing, has been shown compatible with the receiving stream, which serves as a cold water marginal trout fishery.

Jan 1, 1985

By C. A. WARNER

IN all the meetings of the Petroleum Division, emphasis was placed on the essential importance, in the successful furtherance of our war effort, of efficiently producing, transporting, refining, and utilizing maximum quantities of crude oil and natural gas with the minimum expenditure of critical material. With representatives present from all branches of the petroleum industry, from all parts of the United States, the sessions were opened Tuesday morning with Commander Harry P. Stolz. U.S.N.R., Chairman of the Division, and A L. Haider as associate chairmen. From that time until the symposium on petroleum economics was closed Thursday afternoon papers of exceptional interest and importance were presented and discussed in a most frank and open manner.

Jan 1, 1943

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Apr. 10, 1916; to May 10, 1916: Philip P. Baily, New York, N. Y. George W. Otterson Seattle, Wash. John M. Brooks, Jr., Knoxville, Tenn. C. Q. Payne, New York, N. Y. C. A. Burdick, New York, N. Y. Charles F. Potter, Los Angeles, Cal. W. N. Crafts, Oberlin, Ohio. Albert E. Rhoads, Harrisburg, Pa. Andrew B. Crichton, Johnstown, Pa. M. F. Sayre, Schenectady, N. Y. 0. P. Hood, Pittsburgh, Pa. H. V. Smythe, Northpines, Ont., Canada. W. McA. Johnson, Tulsa Okla. W. 0. Snelling, Long Island City, N. Y. G. H. Morgan, New York, N. Y. W. H. Staver, Ophir, Colo. E. G. Norton, Chicago Ill., A. W. Tucker, Salisbury, N. C. M. L. O'Neale, Coal City, Ala. Andrew Weisenburg, Philadelphia, Pa. Arthur H. Brown has resigned his position with the Dome Lake Mining & Milling Co., South Porcupine, Ont., Canada. Robert Sterling has resigned his position as chief engineer of the Goldfield Consolidated Mines Co., Goldfield, Nev., to accept the position of assistant manager of the vanadium mines of the Primos Chemical Co., Vanadium, Colo.

Jan 6, 1916

By John L. Watson

A conceptual model (MAGSEP) is described to simulate the beneficiation characteristics of a drum magnetic separator in terms of the probability of an individual grain being recovered in the magnetic concentrate. This probability is determined as a function of particle magnetic composition and magnetic field strength and is modified by particle size and the separator operating conditions. The model predicts the size, magnetic grade and distributions of magnetic and gangue minerals in the concentrate and tailings produced by the drum separator. The configuration of the magnetic concentration circuit may be altered to permit single or double drum units in parallel or series operation. The characteristics of the feed material, in terms of a magnetic parameter, are essential in permitting the determination of individual grain recovery probabilities upon which the model is based. Thus the model requires input data relating to the distribution of composite grains in terms of magnetic grade and particle size. To illustrate the use of the conceptual model an example is given for the beneficiation of New Zealand iron sands.

Jan 1, 1984

By F. E. Bedale

STUDY of several severe mine explosions that occurred during the winter of 1907 led to the belief that coal dust was a definite explosion hazard. The Consolidation Coal Co. was a pioneer in the early work to' eliminate this hazard and to combat the dangers incident to poor ventilation and the presence of methane. Maintenance of high humidity throughout the mines was one of the first measures adopted, later to be superseded by rock-dusting. In the twenty years from 1907 on, many safety measures were developed and adopted, and several prizes were won, though the practice was crude by present-day standards. But in 1927, the company went to work in earnest, and organized a Department of Safety with adequate personnel and with authority to enforce all approved rules for the prevention of accidents and the preservation of company property. All plans for new construction work, changes in mining systems, and proposals for the purchase of new mining equipment had to receive the approval of this Department. A set of operating- and safety standards was written to govern the activities of all employees, and physical examinations for them were required.

Jan 1, 1938

By AIME AIME

ALFRED WILLIAM GAUGER ??Al" or '?Doc" to his many friends in the coal and chemical industries- is known for his research talents and organizing ability. Appropriately the first public recognition of his technical ability was by the A.I.M.E. in the publishing of a paper by George A. Burrell and Alfred W. Gauger in the "Transactions" for the year 1916. "Al" Gauger was born at St. Paul, July 31, 1892. He graduated in chemistry at the University of Minnesota in 1914. A year later he began his initiation into the mysteries of coal mining when he joined the safety division of the U. S. Bureau of Mines at Pitts- burgh, serving from 1915 to 1917.

Jan 1, 1944

By Edwin Ludlow

EDWIN LUDLOW, president of the American Institute of Mining and Metallurgical Engineers for the year beginning Feb. 15, 1921, is a well-known figure in the state that was the birthplace of the Institute-Pennsylvania-although he was born and educated in New York and is again one of its residents, after years of active work in the field. Mr. Ludlow was born at Oakdale, Long Island, and was graduated from the School of Mines at Columbia University with the class of 1879. After graduation, he became a civilian worker with the U. S. Engineer Corps under General William Ludlow, his brother, and for two years did river and harbor surveying along the New Jersey coast.

Jan 1, 1921

Jan 1, 1931

By J. C. Kerkering, J. C. Franklin, T. O. Meyer, R. W. McKibbin

A continuous survey of radon gas was made in two interconnecting stopes in a southwestern U. S. uranium mine to determine how the various phases of the mining cycle affected the radon concentration. The radon was monitored continuously with five detectors. One detector monitored the intake air, one the exhaust air, and three the stope air. The radon concentrations present during slushing, blasting, and exhaust fan shutoff were compared with concentrations on a nonwork day as a base level. Inside the stope, the radon concentration increased about 40% during slushing and 425% after blasting. Intake air radon increased 1600% and the stope air increased 550% while the surface exhaust fan was off.

Jan 1, 1979

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940

By Charles M. Brinckerhoff

When I first went to Arizona in 1925, mining was primarily an underground job. Ajo, Sacramento Hill in Bisbee and Jerome were the only open pit operations in the state. Thousands of men, however, were employed in underground mining at Morenci, Miami, Inspiration, Globe, Ray, Bisbee, and Superior. The grade of ore in the larger operations was about 1-1/2% copper while a few of the smaller ones mined ore better than 2% Cu. In Utah, the Bingham pit was doing well and growing; in Montana, the vein mines of Butte still yielded ore running 6% Cu.

Jan 3, 1972

By M. E. Shank, J. Wulff

At the present time, the designer of dies for metal powder pressing is handicapped by relative ignorance of stress distribution and frictional effects at the interior surface of the die. Unckell was the first to develop a method for the study of wall friction. He used three Brinell balls on which the die rested during pressing. The total frictional wall force was determined by the size of impression these balls left on a soft metal plate. Since the method does not give radial pressures, or distribution of such pressures, coefficients of friction could not be determined. Although Unckel measured density distribution, he was not able to determine radial or shear stresses. Shaler2 has proposed theoretical expressions for the stress and density distribution within cylindrical compacts during pressing, in accordance with the experimental results of Kamm, Steinberg, and Wulff.3 By application of Siebel's method,4 Kamm et a13 plotted stress trajectories for two compacts. From the stress trajectories they calculated coefficients of friction from point to point along the die wall. As pointed out by Shaler in the discussion of Ref. 3, these values are based on progressive point-to-point calculations on finite size grid squares across the compact. In the region of the die wall such calculated values may therefore have considerable cumulative error. The purpose of the present paper is to develop an experimental method by which the nonhydrostatic pressures and shears acting on the interior wall of a cylindrical die can be measured. Such measurements can then he correlated with existing data to aid in the explanation of the pressing process. The method used is based on the elastic: properties of the thick-walled tube used as the die. The principle of super-position of force systems on an elastic body is assumed to hold. Electric strain gauges were mounted in adjacent positions on the exterior die wall in order to get an exact measurement of the variation of tangential strain over the length of the die during pressing. While in this paper, measurements in terms of only tangential strains are considered, it is well to note that similar calculations may be set up for axial strains. The latter are not preferred, since they tend to be smaller than the tangential strains and therefore permit less sensitive measurements. Discussion in this work is restricted to compacts pressed from both ends, since the elastic deformation of the die is then more amenable to analysis. Before choosing the electric strain gauge method, a more direct line of attack was considered and discarded. The discarded idea was the insertion of a pressure gauge through a hole in the die wall.* The gauge would have been in the form of a small piston. If pressure were exerted against such a gauge, it would move outward along a radius of the die. One disadvantage of the scheme is its inability to measure shears along the die wall. Another more serious disadvantage is the disturbance caused by the device itself. It would serve to change the forces it was designed to measure. No matter how small the movement of the gauge, when pressure is applied a discontinuity would exist in the wall surface at that point. Due to the stress concentration caused by the hole, abnormal deflections of the die wall would occur around the gauge. During pressing, powder would be forced into the resulting depression. The depression would then become larger with increasing compacting pressure. Powder, not being a fluid, is capable of supporting shear. The ease with which it would flow into the die wall depression to further move the piston is an indication, not of the radial pressure at that point, but of the state of shear retarding the movement. Thus the "pressure" gauge is really a criterion of flowability, and of the capability of the powder to support shear. For these reasons, it was decided that the electric strain method, herein employed, was more reliable, if more indirect. The gauges and lead wires, mounted on the external die wall do not in any way affect the behavior of the metal powder or the die during pressing. Theory of the Method THE EFFECT OF RADIAL PRESSURE ON THE DIE WALL Effect of a Single Small Band of Hydrostatic Pressure Consider a die which is a thick-walled cylinder of outer radius R. and inner radius Ri. If over a small finite length L there is a normal pressure P, a tangential strain distribution at the outer wall results. This is shown schematically in Fig 1. The exact shape of the curve may he predicted by an extension of the theory of a semi-infinite beam on an elastic foundation.6 This

Jan 1, 1950

By Ta M. Li

Expanded mine-mill capacity and greater operating flexibility are part of the dramatic changes taking place in the Tennessee mining operations of Asarco, Inc. Climaxed by the recent start-up of the $6.3 million Young mill in September 1975, Asarco has pushed Tennessee back into number one position as the leading zinc mining state. Furthermore, start-up of the Young mill is expected to insure a much-needed and continuing domestic zinc supply, at a time when US mines can only supply one-half of 1975 domestic consumption.

Jan 5, 1976

By Lawrence Addicks

ONE of the properties of copper, which has done much to give it its present prominent place among the useful metals, is its electrical conductivity, a property which has now become the chief criterion of 'the value of the commerical product. In pursuance of that distinctively American principle that, 1' the best is none too good," metal of the highest conductivity is usually called for even where such extreme purity is of no advantage, for instance, in the making of brass and other alloys. The average brass-founder feels nervous unless his copper is so very pure that it shows a conductivity of 99 or 100 per cent., while the character of the zinc used is usually overlooked in his anxiety. Electrolytic refining has made it possible to produce copper of a' very high degree of purity, the metallic impurities averaging but a few thousandths of 1 per cent.; oxygen, usually present in the form of cuprous oxide, bringing the total up to about a tenth of 1 per cent. The published data bearing upon the relationship between chemical purity and electrical conductivity is, however, very scant,' nearly all the work that has been done having dealt with alloys carrying considerable quantities of the foreign elements. In this paper I have brought together the results of experiments extending over a period of several years that have been carried out with the idea of determining the amount of various elements which would lower the conductivity 3 or 4 per cent.-a series of impure coppers rather than alloys. There are many precautions necessary to keep the conditions

Mar 1, 1905