Search Documents

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By C. W. Volek, J. E. Chappelear

The injection of a hot liquid into initially cool porous media, saturated with the same liquid and surrounded by two impermeable but heat conducting media (cap and base rock), has been studied both experimentally and theoretically. The temperature dependence of the viscosity was included in the theoretical model, but it was assumed that the specilic heats and densities of the various materials were independent of the temperature. Solutions to the theoretical model were approximated by numerical methods. Both theoretical and experimental results indicate that center-line temperatures are significantly higher than boundary temperatures. Comparison of experimental and theoretical results with a cold/hot viscosity ratio 01 19:1 were in reasonable agreement. Theoretical calculations show that the effect of the temperature dependence of viscosity was very significant at ratios of 100:l to 1000:1, which are typical of those that occur when injecting hot water to flood heavy oil reservoirs. INTRODUCTION We consider the problem of prediction of fluid flow and temperature distribution in an initially cold-fluid-filled reservoir on the injection of the same hot liquid by the use of mathematical and physical models. The results reported are for a two-dimensional rectangular section of the reservoir, as shown in Fig. 1. The injection and withdrawal faces are assumed to be equipotentials for fluid flow. The ultimate purpose of such models would be to predict hot-water injection performance. However, we note that in the work presented here, one of the most significant aspects of the problem — the instabilities resulting from two-phase, water and oil flow — is not included. We will not give a historical review, but refer instead to the paper of Spillette and Nielsen,1 which contains a rather complete bibliography and critical discussion. The physical problem is exactly the same as Spillette and Nielsen, except for certain simplifications in our assumptions. The mathematical details are somewhat different, and we will present the details of our method here. The mass flow equation, which is elliptic in character, is handled by successive overrelaxation. The heat flow equation, which is parabolic in character, is handled by a straightforward explicit approximation. Some difficulty arose in the over-all heat balance due to small errors in the solution of the mass flow equation, and we feel that a different formulation of the heat flow equation would be desirable for future work. In addition to the mathematical solutions for the temperature distributions in a porous medium due to the injection of hot liquids, experimental data are presented to check the validity of these solutions. A schematic diagram of the model is shown in Fig. 2. Certain qualitative physical conclusions were obtained from our numerical and experimental results. These are: 1. Assuming high (infinite) conductivity normal to the bedding plane in the reservoir is a poor approximation, and may lead to overestimates of the total heat losses (to cap and base rock) of as much as 50 percent. 2. More heat is retained in the reservoir (per unit of heat injected) for higher viscosity changes. 3. Any particular temperature isotherm moves more rapidly along the center line for higher viscosity changes. Consequently, the approximation of temperature independent viscosity is not suitable for obtaining quantitatively correct results. MATHEMATICAL MODEL Our mathematical model is that of a reservoir of thickness 2h. The problem is idealized from that of a linear hot-water drive, and we imagine that the input face is sufficiently far away from the injection wells that the stream lines enter it normally. Similarly the production wells are far enough from the outflow face that the flow lines leave it normally. The reservoir and surrounding cap and base rock

Jan 1, 1970

Organization. Place Date 1915 American Institute of Mining Engineers New York, N. Y. Feb.18-21 National Society for Promotion of Industrial Educa- tion New York, N. Y. Feb. American Institute of Architects.... Washington, D. C. April American Iron and Steel Institute New York, N. I? May New York Electrical Society: New York, N.. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept.9-13 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic City, N. J. Sept.

Jan 2, 1918

By James W. Guider

Of all the technology available to the iron blast furnace operator, raw materials preparation [(Fig. 1)] is by far the most important. Superior raw materials have been basic to the success of the Japanese steel industry, and they are just as essential to the American steel industry in winning its competitive battle against foreign government subsidized steel imports. Therefore, the mine operator and the ore beneficiation engineer must strive to produce the highest quality raw materials possible to meet the precise demands of the modem blast furnace and steel plant.

Jan 1, 1982

By Ali Altway, M. E. Tunison, T. W. Chapman

Simulations of various contactor configurations for simultaneous extraction or stripping of two metals reveal the dependence of conversion and selectivity on operating and design parameters A two-film mass transfer model is used to provide the rates in countercurrent column and stirred-tank cascade calculations Even in these mass-transfer-limited cases the stoichiometry of the extraction reactions introduces nonlinearities and interactions between the two metal transfer rates, but these can be represented In a suitable model One conclusion is that a countercurrent column should be considerably more efficient than a cascade of mixer-settlers of comparable size.

Jan 1, 1981

Edward Leonce Dufourcq, mining engineer, President of Dufourcq & Co., Inc., New York, and Assistant General Manager of the Teziutlan Copper Co., New York, was attacked by bandits and mortally wounded on Wednesday, Apr. 16, while trying out a' gasoline motor car on a line of railroad between Teziutlan and the company's mine, twelve miles away. Word of his death was received Friday by Mrs. Effie Mason Dufourcq of 227 Riverside Drive and by D. C. Brown, Vice-president of the Teziutlan Copper Co.

Jan 5, 1919

By W. F. Laverty

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By R. H. Sweetser

THERE are SO many conditions affecting blast-furnace results that it is hard to get satisfactory comparative data on the working of two furnaces, and much more difficult to get comparable results from the use of two entirely different fuels. The several advantages of charcoal over coke as a blast-furnace fuel have doubtless been apparent to many managers; but probably the conditions for comparative tests of the two were never so favorable as during the year 1905, at the works of the Algoma Steel Co., Sault Ste. Marie, Ontario, which comprise two modern blast-furnaces, well equipped, though of comparatively small capacity. For four consecutive months one of these furnaces was run with charcoal and the other with coke. Then the charcoal-furnace ran for a while with part charcoal and part coke; and, still later, with coke only. The ore-mixtures were about the same in the two furnaces, and, of course, all the climatic conditions were identical. The dimensions of the two furnaces, and their work with the different fuels, are given in Table I.

Jan 5, 1908

By William E. Ford, Edward Salisbury Dana

1. Normal Class (28) Gypsum Type 2. Hemimorphic Class (29) Tartaric Acid Type 3. Clinohedral Class (30) Clinohedrite Type Mathematical Relations of the Monoclinic System Crystallographic Axes. - The monoetinic system includes all the forms which are referred to three unequal axes, having one of their axial inclinations oblique. The axes are designated as follows : the inclined or clino-axis is a; the ortho-axis is b, the vertical axis is c. The acute angle between the axes a and c is represented by the letter 0; the angles between a and b and b and c are right angles. See Fig. 331.

Jan 1, 1922

By C. O. Brawner

Simple, specific rules for achieving slope stability in open-pit mines are impossible to devise. Each pit has a different mining program and a different set of environmental conditions, and its final slope design must be based on an individual evaluation of the actual site. The overall philosophy of pit stability, however, is tending towards a limit design concept. Since slope angle has a great influence on the economics of most open-pit mines, efforts are being made to reduce the theoretical factor of safety for slope stability to very near 1.0. (Factor of safety is here defined as shear strength/shear stress on the most probable plane of failure.) Actually, where detailed, statistically significant testing has been done and a comprehensive ground control program is being instituted to warn of movement at an early stage, safety factors as low as 1.1 or 1.2 may be justified. The cost of the necessary procedures, however, is high. There are many factors that influence stability, but this article will be confined to three-rock structure, groundwater, and blasting.

Jan 8, 1969

By F. Milton Lewis, Roshan B. Bhappu

In Part I of this article, published in the September issue of MINING ENGINEERING, Edward S. Frohling and Robert M. McGeorge of Mountain States Mineral Enterprises, Inc., reviewed the general overall financial aspects and methods of raising the necessary capital for developing the mine. In Part 2 of this two-article series, we will present several case histories to show how realistic feasibility studies are used for evaluating the choices and options entailed in mining ventures. Basically, after a potential ore body has been discovered, and the necessary funds obtained for the development of the deposit, the next major problem is one of ascertaining what specifically is to be produced, and the costs of production. The profit potential of the mining venture can then be accurately assessed by the mine owner, operator, or loan officer.

Jan 10, 1975

By W. A. Sheaffer

Electric furnace installation and tough-pitch copper-casting operation at Canadian Copper Refiners Ltd. are described. General layout, power supply and control, refractories, induction pour hearth, casting equipment, metal temperature control, and oxygen-content control are discussed. E LECTRIC furnace at Canadian Copper Refiners Ltd. was put into operation in August 1949. The installation was designed primarily to melt electrolytic copper cathodes and to produce vertically cast tough-pitch shapes. To meet emergencies during reverberatory furnace shut-downs, provision was made for casting horizontal tough-pitch wire bars. Due to the ease with which metal temperatures, melting rates, oxygen content, and casting hours can be altered to suit production demands, the electric furnace has met the requirements admirably. General Layout The plant has been described by H. S. McKnight' and by J. H. Schloen and E. M. Elkin.2 Since these papers were written, the electric furnace has been installed in a 140 ft extension of the original casting building. The extension, 264 ft in width, is divided into one 24 ft and four 60 ft bays, each a continuation of similar bays in the older building. Fig. l, a partial floor plan of the extension, shows the location of major equipment. Power Supply and Control Power for the electric furnace and its auxiliary equipment is delivered by Quebec Hydro over two 12 kv three-phase, 60 cycle pole lines. One line is in use, while the second serves as an emergency standby. Connections for the electric furnace from these lines, which also feed the refinery power house, are made to a substation on Canadian Copper Refiners Ltd. property. Connections between this substation and the furnace transformer room are in underground conduit. The are-furnace transformer, 550 v auxiliary-equipment transformer, and 12 kv switchgear are in the transformer room near the furnace. Stepdown from 12 kv to are-furnace voltages is done by a 7500 kva oil-immersed water-cooled three-phase 60 cycle transformer. This unusually high kva rating is available because the arc furnace and transformer were adapted from a steel-melting unit. Secondary voltages are available in 16 steps between 251 and 95 v (across phases). A four-position tap changer, operated from the furnace switchboard is connected to taps yielding 199, 164.5, 127, and 115 v, respectively. The transformer primary feeder is equipped with a General Electric Magne-Blast circuit breaker. The pour hearth, casting wheel, bosh conveyor, and other auxiliary equipment are fed by a 12 kv to 550 v, 750 kva three-phase 60 cycle transformer. Graphite electrodes, 14 in., with tapered nipples are held in the are-furnace electrode arms with steel wedges. The arms, fed from the transformer secondary busbars by flexible cable bundles, are actuated by winch cables. Direct-current motors operating the winches are supplied by a 250 v motor-generator set. Power input to the furnace is controlled from the furnace switchboard. The board has the usual combination of remote controls for the 12 kv breaker and transformer tap changer, meters, overload relays, automatic and manual electrode motion controls, switchgear, etc. When power is on the furnace, automatic electrode feed is used; the power draw on a given voltage tap then is governed by current-limiting rheostats. The rheostats work through a Westinghouse bal-lanced-beam control circuit which, in turn, operates reversing contactors in the winch motor circuits. Arc Furnace The arc furnace is a standard-type NT Pittsburgh 'Lectromelt with inside shell diameter 12 ft 3¾ in. By hydraulic-lift cylinders, the furnace can be tilted forward to 39 ½ ° and backward to 5" from horizontal. A roof-swing cylinder is also installed but not used. Fig. 2 shows refractory-lining details. With the lining as shown, operating life between repairs is 6 to 9 months of two-shift casting operation. Charge slot, skim door, and roof refractories then are replaced completely, and any necessary repairs made to side walls. Bottom life is longer and the original under courses are still in service, while the top course was replaced in October 1951. The launder is lined with high chrome-magnesite trough brick backed by fireclay and insulating brick. The trough is covered with fireclay brick and asbestos sheet. At intervals, openings 12x6 in. are left in the permanent covering. These are covered with

Jan 1, 1956

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10 to Aug. 10, 1915: Members ALBERTSON, MAURICE MERTON, Mine Surveyor, Mining Corporation of Canada, Cobalt, Ont., Canada. ARMSTRONG, GEORGE CHANDLER Mgr., Indian Refining Co., Lawrenceville, Ill. BARBER, MAX HAYDEN, Min. Engr Supt., Crosby Mine, Nashwauk, Minn. BARNESON, JOHN Merchant, 310 Sansome St., San Francisco, Cal. BENSEL, JOHN A., Cons. Engr 111 Broadway, New York, N. Y . BORGESON, ANSHELM CYRUS, fin. Engr Shenango Mule, Chisholm, Minn. BROOKS, CHARLES PETER, Min. Engr 228 Dooly Bldg., Salt, Lake City, Utah. BROWN, FRANK HAROLD, U'011',. Min. Engr., Federal Co., Inc., 50 Broad St., New York, N. Y. CLARK, DOUGLAS Kellogg, Idaho.

Jan 9, 1915

By F. G. McCutcheon

UNTIL about 1930, the universal practice of horizontal-retort zinc smelters in the United States, as far as the writers are aware, was to operate the retort furnaces on a 24-hr cycle; that is, the retorts were charged in the early morning of one day, and in the early morning of the following day the residues were cleaned out, the retorts recharged, and a new cycle started. During the business depression of the early thirties, zinc production fell off to the extent that zinc smelters had idle retort capacity. Rather than continue to run some of the retort furnaces on a 24-hr cycle and shut down the remainder, a few companies decided to try out a longer cycle. Although the output of zinc per retort per day is lower, the longer cycle permits a larger charge per retort and improved zinc recovery. Advantages of the longer cycle were soon evident, and the practice spread rapidly. Various lengths of cycle were used, typical examples being 28-hr, 32-hr, 36-hr, and 48-hr. The 48-hr cycle fits in best with the standard routine of smelter practice that was built up on the basis of the 24-hr cycle; that is, the retort furnace "maneuver" always comes at the same time of day, and can be performed in the cool hours of the early morning. Under some conditions, particularly in some of the older plants, where the retorts are smaller than in newer plants, a 48-hr cycle is longer than necessary, and some intermediate length of cycle may theoretically be most economical. Use of an intermediate cycle, however, means that the maneuver comes at different times on consecutive days, and that sometimes it comes during the hottest part of the day. The work on the retort furnaces is extremely hot and arduous at best, and it is much worse, of course, if it is done during the heat of a summer day. When labor was plentiful and tractable, many plants were able to operate on cycles of intermediate length, but the workmen did not like the working hours. Under present labor conditions, it is hardly practicable to operate with a cycle of intermediate length, so the choice has narrowed down to the alternatives of 24-hr or 48-hr cycles. In any discussion of economics, too comprehensive generalization is not warranted, because local conditions affecting economics vary greatly. The best economic practice at one plant at any given time may be uneconomical at another plant, or even at the same plant at another time. To determine the length of cycle that is the better practice at a given plant at a given time requires a weighing of the advantages and disadvantages of each cycle, taking into consideration all the local conditions. Some of the factors that must be considered in making the comparison are discussed briefly in the following paragraphs.

Jan 1, 1947

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By Harold V. Pearce

THE plant of the Boston and Colorado Smelting Company, at Argo, Colo., has not received special notice in technical or scientific publications for some time past. Dr. Peters' described the development of the reverberatory furnace used at Argo, but he dealt almost exclusively with the increase in size and the corresponding gain in capacity. Since the time of his description the changed conditions have led to a modification of the former smelting practice, and this modification forms the basis of the present paper. No claim is made for personal originality in connection with these improvements, in fact, I expressly disclaim any such intention, since nearly every successful step in the development of the process now used at Argo has been suggested by Dr. Richard Pearce at various times during the past 12 years, though perhaps in a different manner of exe¬cution. These changes would undoubtedly have been made before, were it not that many problems of greater metallurgical importance and momentarily of more urgent need thus had to be solved. At the time to which I refer, economic conditions demanded mainly an increase of capacity. Moreover, the determination and placing of exact losses in smelting were not so imperative as they now are. About three years ago, the time of my appointment to the - management of. the works of the Boston and Colorado Smelting Co., the great decline in the price of copper occurred; the Argo plant, in common with all others engaged in the copper-industry, lost heavily in the market-value of the stocks on hand of ore and furnace-products. Added to this was the unfortunate circumstance that the copper-supply of the Argo plant from general sources began to dwindle; in fact, it almost entirely ceased. About this time the smelting-plants in the west-

Mar 1, 1905

Jan 1, 1915

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.1

Jan 10, 1953

By W. L. McMorris, Shiou-Chuan Sun

The Convertol process was first described in Ger- many by Muschenborn1 in 1952. In the U. S. Fraser2 reported this new process in 1953, and Brisse and McMorris-resented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals.

Jan 11, 1959

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 (2.09 rad) apart into the outer surface of a hollow cylindrical steel, tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau of Mines on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U.S. patent (3,914,992) assigned by the author to the Dept. of the Interior was granted Oct. 28, 1975.

Jan 1, 1978