Search Documents

By AIME AIME

AN entirely new type of classifier is being put on the market by The Dorr Co., following three years of development and the experimental use of thirty machines of the improvement design in various parts of the world. It is known as the Multizone classifier. Compared with the older type the lower or overflow end has been decked over and is surmounted by one or more circular overflow columns. Feed is introduced near the middle of the machine and passes downward and under a vertical baffle, then along the underside of the deck to the base of the overflow columns. Under the baffle there is a restricted turbulent zone of high pulp velocity which holds the fine and critical size particles in suspension, preventing

Jan 1, 1937

By Luke L. Y. Chang, Bert Phillips

ThE tendency toward further oxidation of the intermediate oxides and the high volatilization rates of the higher oxides have prevented direct attainment of equilibrium data for the system tungsten-oxygen. As a result, St. Pierre et al.1 have proposed a phase diagram (to 800°C) based on thermody-namic data to 1200°C for the known tungsten oxides (WO2z, W18O49, W20O58, and WO3) and a report on a tungsten suboxide W3O.2 Recent modification of a technique previously described3 5 now permits adequate preservation of compositions of mixtures of metallic tungsten and metal oxides (e.g., of tungsten, cobalt, calcium, samarium, titanium) in order that condensed phase relations may be established to 1700 This method has been applied to study the high-temperature stability of tungsten oxides. In the method used, the desired compositions were sealed in nonreactive containers such that only a small gas volume remained. Each sample then established its own equilibrium atmosphere at temperature. This method has advantages in the study of systems of the W-0 type where knowledge of the condensed phases is desirable but for which composition and pressure of the gas phase are not readily attainable because of oxide volatility. Mixtures of 99.99 pct tungsten metal powder and purified tungsten anhydride (WO3) or in some cases W18O49* were equilibrated in pellet form in sealed

Jan 1, 1964

By Thomas Read

AMONG the large number of deep mines in the world there are several which do not differ much in depth. The St. John del Rey mine, in Brazil, has reached a vertical depth of 6726 ft. below the top of its shaft; miners enter it, however, through an adit which intersects the shaft 324 ft. below its top, wherefore it might be said that the mine is really only 6400 ft. deep. In the Kolar gold field of India there are a number of deep shafts, one of which reaches to a vertical depth of 6140 ft. below surface. In South Africa also there are a number of deep shafts, the Village Deep being 6100 ft. early in 1921. The City Deep, Ltd., proposes to sink to a depth of 7000 ft. but pre-sumably by the time it does so the St. John del Rey will be deeper than that, since it has been increasing in depth at an average rate of about 150 ft. per year. The deepest shaft in the United States, the Tamarack No. 5, although it is only 5308 ft. deep, actually approaches nearer to the center of the earth (4100 ft. below sea level, as against 3958 ft. , at St. John del Rey). The deepest workings in the Calumet & Hecla go down to 4600 ft. below sea level. The St. John del Rey is not only the deepest, mine in the world, but it also is worked by the oldest registered English mining company, which was organ-ized in 1830 to work a mine at a considerable dis-tance from this one. That mine proved unprofitable, and in 1837 operations were transferred to the. deposit now under discussion, where operations have been prac-tically continuous ever since.

Jan 6, 1923

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

By Maynard O. Serbousek, James R. McVey

IS there a quick way of assessing the conditions of a newly exposed roof in a coal mine? This has always been a nagging question. The problem is that unless effective controls are established as soon as possible, it becomes extremely difficult to extract coal safely and economically from conventional underground milling operations. Until recently, little has been done to provide a means of measuring the structural behavior of a coal mine roof while the face advances during actual production. (In fact, most measurements have always been made after the fact or during a roof pull-down where the roof is actually caused to fail with no support.)

Jan 9, 1976

By G. M. Schwartz, J. N. Gundersen

John W. Gruner (Professor Emeritus, College of Science, Literature, and the Arts, Dept. of Geology, University of Minnesota, Minneapolis) — It is surprising that two men as well acquainted with the taconite rocks of the Mesabi District as Drs. J. N. Gundersen and G. M. Schwartz should have concluded that the taconite of the Eastern Mesabi before the intrusion of the Duluth gabbro consisted largely of quartz and magnetite. These minerals were "locally reconstituted" into "a wide variety of silicate mineral assemblages" by the gabbro. It is well known, of course, that the silicate mineralogy of the Eastern Mesabi ('about 14 miles in length) is quite different from that of the Main Mesabi which is over 60 miles long. The change from one to the other is abrupt and cannot be attributed to any other cause than the thermal effects of the gabbro. Are we to assume or believe that the taconite of the Eastern Mesabi was radically different from that of the Main range before the gabbro metamorphosed it?

Jan 1, 1962

By E. L. Spain

The deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respectively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewelll and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a 'general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance. Location of Tripoli Deposits Fig. 1 shows the locations of deposits of tripoli in a long belt that extends from northeast Wayne County southwestward into northwest Alabama and thence passes into Mississippi, where the formations carrying it are finally covered by Cretaceous sand and gravel of the Mississippian Embayment. Occasional deposits occur also in the southeastern corner of Hardin County, Tennessee. While tripoli is found at nearly all points along this axis where the related formations are exposed, the largest deposits are grouped about three different centers. Waynesboro-Collinwood District.—In the area between Waynesboro and Collinwood, in Wayne County, Tennessee, tripoli of various grades outcrops in the valley of Green River and in tributary valleys on either side. This district is roughly 12 miles long in a northeast-southwest direction and has a maximum width of 5 miles at its northern end. Exposures are found in road cuts, highway chert pits, in the beds of some of the streams, and on hillsides. The greatest number of high-grade

Jan 1, 1938

By E. L. Spain

The deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respectively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewelll and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a 'general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance. Location of Tripoli Deposits Fig. 1 shows the locations of deposits of tripoli in a long belt that extends from northeast Wayne County southwestward into northwest Alabama and thence passes into Mississippi, where the formations carrying it are finally covered by Cretaceous sand and gravel of the Mississippian Embayment. Occasional deposits occur also in the southeastern corner of Hardin County, Tennessee. While tripoli is found at nearly all points along this axis where the related formations are exposed, the largest deposits are grouped about three different centers. Waynesboro-Collinwood District.—In the area between Waynesboro and Collinwood, in Wayne County, Tennessee, tripoli of various grades outcrops in the valley of Green River and in tributary valleys on either side. This district is roughly 12 miles long in a northeast-southwest direction and has a maximum width of 5 miles at its northern end. Exposures are found in road cuts, highway chert pits, in the beds of some of the streams, and on hillsides. The greatest number of high-grade

Jan 1, 1938

By Paul M. Musgrove, Larry S. Diaz

Recent tests conducted at Inspiration Consolidated Copper Co. examined some aspects of the value of a continuous measurement of particle size to the operation and control of a mill grinding circuit. Inspiration's control objectives and kinds of control systems developed in recent years to attain these objectives are outlined. A description is given of the arrangement of the test circuit at Inspiration and also of the systems used to measure particle size of the cyclone overflow product in these tests. Use of on-line size measurement for the analysis and improvement of grinding circuit performance is illustrated by relating how two important relationships were detected. Finally, the performance of a particle-size-based control system is described, including preliminary conclusions as to increased productivity.

Jan 1, 1974

By Rizo-Pairón Alfonso, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector The results obtained indicate that a I I ratio of collector ion to activator ion gives optimum results, and that a 2 I ratio almost fails to achieve activation and flotation Yet, a 2 I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids, they confirm that an adsorbed coating is inescapable APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz The flotation machine was built according to the design of D W McGlashan It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine The air intake is controlled by a valve, and the cell consists of a beaker The quartz was obtained from vein quartz stored in large chunks It was first crushed to 20 mesh, then sized on a 28-mesh screen The 20 to 28-mesh size alone was retained for use This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used The barium was used as barium chloride, Baker's analyzed C P The oleate was used as sodium oleate It was prepared from sodium hydroxide, Baker's analyzed C P , and oleic acid purified by R R de Arellano3 in the laboratories at the Massachusetts Institute of Technology The purification procedure was elaborated from the recent researches of Brown and Shinowara 2 It consisted in (I) saponification of olive oil with potassium

Jan 1, 1942

By AIME AIME

THE value to the engineering profession of a liaison between the engineering societies of Russia and America, through Engineering Council, was the subject of a meeting in the Engineering Societies Building attended by over 500 persons. In introducing the subject, Mr. N. A. Stephanoff, President of the Russian Society of America, said: In Russia, engineers were divided into two classes: those who had graduated from the high technical schools and the practical engineers who had graduated from special technical schools. These technical schools were divided into three groups: The first corresponded to the German polytechnical schools with many departments, mechanical, chemical, metallurgical, mining, etc. The second group corresponded to the French special schools of the "Écoles des Ponts et Chaussées." "École des Mines." The third group was formed by the Military and Naval Academies of Engineers. In 1910, Russia's high technical schools had about 45,000 students, whose training covered a period of not less than five years, and who enjoyed all opportunities afforded by laboratories in no way inferior to those of Germany.

Jan 1, 1920

By A. D. Marlin, A. J. Gentile, E. F. Jordan

Metallurgical changes in SAE 52100 ball-bearing components resulting from overload testing are described. Changes in microstructure, hardness, and resiclctal stresses crre discussed zuitlz re.ference to material cleanliness obtained by various steel-melting practices and are compared with work by otlzer investigators. Evidence is presented to show that the initialion and development of microstruc-tural alterations are characterized by two separate reactions: the appeavance of a "dark etchingJ' constituent, and "gray lines" or a light etclzing constituent. The dependency of these tzvo reactions on material cleunliness, running tirne, and contact stresses is discussed and a failure mode related to material cleanliness and microstructural transformation is proposed. THE study of ball- and roller-bearing contact fatigue has been paced by a strong emphasis on bears ing application performance. Particular attention has been paid to conditions that effect the spalling-type failure that is characteristic of rolling contact fatigue in through-hardened components. Some of the conditions investigated are lubrication and atmosphere,1-3 material characteristics and finish,475 and speed and design fa~tors."~ A typical spalling-type failure is shown in Fig. 1. The arrow shows the motion of the ball relative to the inner-ring race surface. The leading edge of the spall is usually sharper than the trailing edge. The race surface near the trailing edge also shows small dents caused by debris from the spall. In this type of testing very little metallurgical investigation is done on failed bearings. Emphasis is placed on test conditions and statistical analyses of endurance data. More basic work has been done relating micro-structural changes to fatigue performance. Dyer" and Wood, Cousland, and sargant9 have used mostly simple materials, such as single crystals and single-phase polycrystalline specimens, under simple alternating strain to identify a systematic process of fatigue damage. drutowski" was concerned primarily with the relationship between steel structure, contact stress, and energy losses in rolling contact. dones11 and Bush, Grube, and Robinson12 utilized changes in microstructure and residual stress in overload-tested rolling contact elements as a means of investigating the fatigue process. Work is being done on an ASME-sponsored contract,13 using both simple and complex materials, but there is still a long way to go before such theories as pore and void growth in simple structures can be applied to the relatively complex bearing steel microstructure. The purpose of this paper is to report on an investigation into the effect of steel cleanliness on the structural alteration and residual stress changes found in overload-tested ball bearings. Using these results and those of previous investigators, we will propose probable failure mechanisms in both overload- and normal load-tested ball bearings.14,15 PROCEDURE Ball bearings? 3208 size, were fabricated from SAE 52100 steel obtained by five different melting practices. The melting practices, chemistry, and inclusion ratings for the five lots of steel are summarized in Tables I and 11. The nonmetallic inclusion ratings were determined by the Jernkontoret method described in ASTM E45-51 Method A. This technique consists of microscopically examining a series of polished samples taken from specified locations in the ingots, billets, or bars. Each sample is surveyed at XlOO magnification and the inclusion types and sizes are compared to standard fields. Because of the nature of these ratings all values in Table I1 are rounded to the nearest half. The elec-

Jan 1, 1965

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By M. W. Hayward

THE object of this paper is to record and tabulate the data and field observations obtained by the writers and their associates during 10 years of intensive study of lead-zinc deposits in the Cretaceous limestone areas in Northern Mexico, particularly in mines owned by the Cia. Minera de Peñoles, S. A. At the El Paso meeting of the Institute in October, 1930, J. G. Barry made the suggestion that a committee be appointed to correlate the ideas and theories which have been put forth by the numerous engineers and geologists who, during recent years, have made a study of the ore deposits in the area under consideration. The first step in a work of this nature would be to record all of the observed facts, and these facts would have to be accepted by those who attempted to formulate a theory of ore deposition. It is with this idea in mind that the writers have described as accurately as possible the actual, observed facts pertaining to the occurrence of the lead-zinc ores in dolomites or dolomitic horizons. By most writers the term "dolomite," is loosely used to designate magnesium-bearing limestones, regardless of the percentage of MgO present. Since no, true dolomites exist in the areas to be described, we shall also loosely use the terms dolomite or dolomitic limestone to designate those beds having a magnesia content of 5 per cent MgO or more. For a number of years the writers have been impressed with the fact that in areas where dolomite beds occur a large percentage of the lead ore is found in these beds, in spite of the fact that such beds may be overlain or underlain by pure limestone, which one would assume to be just as favorable for replacement as the dolomite, if not more 'so on account of its being more soluble in acid solutions than the dolomite. It is true that in some limestone areas, such as the Erupcion-Ahumada districts, Chihuahua, and Providencia, Zacatecas, where no dolomite beds have been found, large tonnages of lead ores have been mined. We venture to predict, however, that had there been dolomitic beds in these areas, the

Jan 1, 1931

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By AIME AIME

THE MODEL LAW previously referred to', in these columns several times, prepared by Engineering Council, to be o ered in any state where legislation is introduced for licensing engineers, is given in abstract below. , Mining engineers throughout the country should watch legislation of this sort and see that the draft prepared by Engineering Council is in the hands of any state legislative committee which proposes to frame a licensing law. So far as this office is informed, the mining engineers are a unit against licensing, but if we must be licensed the most innocuous law that has been submitted is the draft prepared by Engineering Council. ABSTRACT OF MODEL LAW -FOR REGISTRATION OF PROFESSIONAL ENGINEERS, ARCHITECTS, AND LAND SURVEYORS

Jan 1, 1920

By F. Forward, H. Veltman, A. Vizsolyi

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By Richard R. Klimpel

The role of dispersion is described in the wet grinding of ores using tumbling media mills and the flotation of coal, sulfide, and non-sulfide ores. Emphasis is placed on characterizing the effects of dispersion in laboratory tests using engineering models which provide information useful for the improvement and control of existing plant operations. Significant economic gains in the above named operations have been realized using these models as guides for full- scale plant testing.

Jan 1, 1980

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before break-age, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 8, 1950