Search Documents

By O. F. Walker, W. C. Hahn, V. A. Johnson, J. D. Wood

The diffusion coefficients of zinc in single-crystal zinc and carbon in single-crystal and poly crystalline nickel were measured by means of radioactive tracer techniques both with and without the application of ultrasonic vibrations under conditions such that the temperature of the sample was closely controlled. The results of this investigation indicate no enhancement of diffusion in any of the samples. It is suggested that previously reported enhancement may have been due either solely to temperature increases caused by ultrasonic vibrations or in combination with changes in the boundary conditions. A number of observations have been reported in the literature in which it has been implied or inferred that the application of ultrasonics enhances diffusion (see, for example, Refs. 1-5). The present study was undertaken in an attempt to observe this effect under carefully controlled conditions, particularly with regard to measurement and control of the temperature of the sample. Two different types of systems were studied; these were the self-diffusion of zinc and the diffusion of carbon in nickel. EXPERIMENTAL For diffusion with ultrasonic energy applied, the samples were included as part of a resonant ultrasonic system operating at 58.5 kcps. The ultrasonic generators used were rated at 100 and 250 w and could be tuned over a frequency from 10 to 100 kc. A PZT (lead titanate/lead zirconate) ceramic transducer provided the driving vibration. This system requires no metallurgical joining of the specimen to the acoustical transmission line since the ultrasonic driver and the follow-up section clamp the specimen in position by means of a constant pressure of 50 lb developed by an air cylinder. The ultrasonic driver and follow-up section, both made of titanium, were 4 in. in length from clamping point to the end in contact with the specimen. Using the relationship given by Mason,6 A = V/f, the resonant wavelength, A, in titanium is calculated to be 3.3 in. at a frequency, f, of 58.5 kc, taking the velocity of sound in titanium, V, as 1.95 X 105 in. per sec. The 4-in. driver and follow-up section, therefore, are each 4.0/3.3 =1.21 times the resonant wavelength. Clamping pressure must be applied at stress nodes of the transmission line in order to preserve resonance. Therefore, a specimen length of 0.58 times the wavelength in the specimen was required to place the clamping pressure application points at stress nodes exactly three wavelengths apart. A stress antinode was contained in the center 3 in. of the specimen. A small PZT ceramic disc attached to the follow-up section provided an output voltage proportional to the intensity of the standing wave. This output voltage was monitored on an oscilloscope and the ultrasonic system was tuned to resonance by varying the frequency until the output signal was a maximum amplitude. The amplitude of the output signal was maintained constant throughout the diffusion anneal. A split cylindrical stainless-steel chamber, which was purged with argon prior to and during the runs, was placed around the specimen. The chamber in turn was surrounded by a movable furnace whose temperature could be controlled to 7C. Heat exchangers were used to cool the driver, follow-up section, and ultrasonic transducer. Great care was taken to obtain the true specimen temperature in all cases. Several different methods were tried; the most successful was that in which the thermocouple was held in contact with the midlength of the specimen by means of an asbestos insulating pad and wire straps. In the case of zinc, single-crystal specimens of 99.999 pct purity were used. The samples were 0.25 by 0.25 in. square and of the proper length for resonance, that is 1.1 in. long with the c axis parallel to the long dimension of the specimen for the case of diffusion perpendicular to the c axis and ultrasonic motion parallel to the c axis, and 1.9 in. long with the c axis perpendicular to the long dimension of the specimen for the case of diffusion parallel to the c axis and ultrasonic motion perpendicular to the c axis. In each case, one of the rectangular faces was electroplated with a thin film of zinc containing Zn The constant pressure used to clamp the specimen in place in the ultrasonic system caused some deformation in some of the samples. For these samples the deformation was concentrated in either end of the specimen; thus, for all samples (both zinc and nickel) the center in. was cut from the specimen after the diffusion anneal to be used for sectioning and counting. The nickel single-crystal samples, of 99.999 pct purity, were used in the form of rods 0.25 by 0.187 by 2.07 in. long with the (100) direction parallel to the rod axis. The polycrystalline nickel samples of 99.97 pct purity had an average grain diameter of 0.007 in. and were used in the form of rods 0.25 by 0.125 by 1.87 in. long. The direction of ultrasonic motion was parallel to (100) direction (bar axis) for the single-cqstal samples and parallel to the bar axis for the polycrystalline specimens. A thin film of c14 suspended in methanol was applied to the diffusing face of the specimen. Two specimens were butted together lengthwise for each diffusion anneal to minimize oxidation. After diffusion, a precision lapping device similar to the one described by Goldstein7 and a radiation detector were used to obtain a plot of specific activity vs penetration distance for each specimen. (A scintil-

Jan 1, 1969

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By H. R. Shidel

THIS paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. S. Bureau of Mines; Magnolia Petroleum Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by fine-grained, well cemented sand, which is barren. Possibly two, or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 10, 1918

By A. H. Larson, L. G. Twidwell

The influence which Au, Ag, Sb, Bi, Sn, and Cu have, both individually and collectively, on the activity coefficient of sulfur in liquid lead at 600"C zuas studied by circulating a H2S-Hz gas wlixture over a specific lead alloy until equilibrium was attained. Subsequently, the H2S concentration in the equilibrium gas mixture and sulfur concentration in the condensed phase were deterruined. The elements gold, silver, and antinzony (above 8 at. pct) increased the activity coefficient of sulfur. Bismuth had no apparent effect. Tin (above 3 at. pct) and copper decreased the coefficient. The influence of an individual element, i, on sulfur is best reported as the interaction parameter, riS, which is defined as The values o these first-order interaction zus are: ESzu = —55.0. These interaction parameters are used to predict the activity coefficient of sulfur in six fouv-component alloys and one seven-component alloy. Comparisons are made with direct experimental determinations. INTERACTIONS in dilute solution have been studied by many investigators. Most of the experimental work has been confined to solute-solvent interactions in simple binary systems and solute-solute interactions in ternary systems. Dealy and pehlke"~ have summarized the available literature on activity coefficients at infinite dilution in nonferrous binary alloys and have calculated from published data the values for interaction parameters in dilute nonferrous alloys. Interaction parameters are a convenient means of summarizing the effect of one solute species on another in a given solvent. Only a few investigators have studied interactions of the nonmetallic element sulfur in a metallic solvent. They are as follows: Rosenqvist,~ sulfur in silver; Rosenqvist and Cox,4 sulfur in steel; chipman, sulfur in alloy steels; Alcock and Richardson,% ulfur in copper alloys; Cheng and Alcock,' sulfur in iron, cobalt, and nickel; Cheng and ~lcock,' sulfur in lead and tin. The only reported work on the Pb-S system in the dilute-solution region is that of Cheng and Alcock.' Their investigation involved a study of the solubility of sulfur in liquid lead over the temperature range 500" to 680°C. The results may be summarized by the following relationship: S (dissolved in lead) + Pb(1) = PbS(s) log at. %S = -3388/T + 3.511 Experimentally, it was found that Henry's law was valid up to the solubility limit of sulfur in lead, i.e., at 600°C up to 0.43 pct. Their investigation did not include the study of sulfur in lead alloys. More accurate calculations could be made in smelting and refining systems if activity coefficients of solute species could be accurately predicted in complex solutions. One of the objectives of this study was to compare the experimental data with the values calculated from the equations derived from models for dilute solutions proposed by wagner9 and Alcock and Richardson. A temperature of 600°C was chosen as the experimental temperature to attain reasonable reaction rates and to minimize volatilization of the condensed phase. EXPERIMENTAL Materials. The Pb, Au, Ag, Sb, Bi, Sn, and Cu used for preparation of the alloys were American Smelting and Refining Co. research-grade materials. All were 99.999+ pct purity except the antimony and tin which were 99.99+ pct. The initial alloys prepared for this study consisted of twenty-one binary alloys, eleven ternary alloys, and one six-component alloy. The constituent elements were mixed for each desired alloy and were placed in a crucible machined from spectrographically pure graphite. The crucible was placed in a vycor tube which was evacuated with a vacuum pump and gettered by titanium sponge at 800°C for 8 to 12 hr. After the gettering was completed, the chamber containing the titanium was sealed and removed. The remaining sample chamber was placed in a tube furnace at 800°C for 2 hr and quenched in cold water. The final operation consisted of homogenization of the alloy for 1 to 2 weeks at a temperature just below the solidus for the individual system. The resulting master alloys were sectioned into small pieces and a random choice made for individual equilibrations. Cobalt sulfide (Cogs8) used to control the gas atmosphere in the circulation system was prepared by passing dried HzS for 24 hr over a Co-S mixture heated to 700°C in a tube furnace. This material was then mixed with cobalt metal to give a two-phase mixture which, when heated in hydrogen to a particular temperature, produced a desired H2S/H2 gas atmosphere in the circulation system. A Cu2S-Cu mixture also used in this study was prepared in a comparable manner. Apparatus for Equilibrium Measurements. The experimental technique of this study required apparatus

Jan 1, 1967

By R. B. Kelly, Paul Martin

Central Texas added 76 producing oil and gas wells during the year, abandoned 378 wells in the same period, and produced 10,359,905 bbl. of oil in the 12 months under consideration. The oil production represents a decline of only 3 per cent as compared to 1934, but it must be remembered that much new production was added during the year. The activity in new work centered in Frio, Bexar, Williamson and Cald-well counties, with development in the Pearsall, Von Ormy and Byersville fields taking first importance. New discoveries in 1935 were confined to Pearsall area of Frio County and an extension to the Darst Creek field in Guadalupe County. The Red Lake field, in eastern Freestone County, proved itself of importance from the standpoint of a gas reserve but no oil production has yet been obtained. In Bexar County, the Von Ormy field, in which the discovery well was drilled early in 1934, completed 22 oil producers during the year. (A map of Central Texas showing location of oil and gas fields was published in Volume 114 of the A.I.M.E. Transactions.) New Fields Pearsal1.—The Amerada Petroleum Corporation, in developing its 60,000-acre block in Frio County, has definitely proved the existence of commercial oil production in four separate horizons; namely, the Navarro, the Austin Chalk, the Buda and the Georgetown. The discovery well, a two million cubic foot gas well, was tompleted in 1934. A test of the Trinity sand at 10,050 ft. found salt water but later was plugged back and finished as an oil well in the Navarro sand. Most recent of their discoveries has been in the Austin Chalk at a depth of 5666 ft., where a 24-hr. gage through 1-in. choke showed 2640 bbl. of pipe line oil. The oil has a gravity of 28.0" A.P.I. and is brownish in color. Because of lack of pipe lines in the area, the wells are produced only for short periods of time, and it is predicted that development will be slow until the district is entered by pipe line purchasing companies. Von Ormy.—In March, 1934, Umbren et al. completed their Wentz

Jan 1, 1936

By Paul Martin, R. B. Kelly

Central Texas added 76 producing oil and gas wells during the year, abandoned 378 wells in the same period, and produced 10,359,905 bbl. of oil in the 12 months under consideration. The oil production represents a decline of only 3 per cent as compared to 1934, but it must be remembered that much new production was added during the year. The activity in new work centered in Frio, Bexar, Williamson and Cald-well counties, with development in the Pearsall, Von Ormy and Byersville fields taking first importance. New discoveries in 1935 were confined to Pearsall area of Frio County and an extension to the Darst Creek field in Guadalupe County. The Red Lake field, in eastern Freestone County, proved itself of importance from the standpoint of a gas reserve but no oil production has yet been obtained. In Bexar County, the Von Ormy field, in which the discovery well was drilled early in 1934, completed 22 oil producers during the year. (A map of Central Texas showing location of oil and gas fields was published in Volume 114 of the A.I.M.E. Transactions.) New Fields Pearsal1.—The Amerada Petroleum Corporation, in developing its 60,000-acre block in Frio County, has definitely proved the existence of commercial oil production in four separate horizons; namely, the Navarro, the Austin Chalk, the Buda and the Georgetown. The discovery well, a two million cubic foot gas well, was tompleted in 1934. A test of the Trinity sand at 10,050 ft. found salt water but later was plugged back and finished as an oil well in the Navarro sand. Most recent of their discoveries has been in the Austin Chalk at a depth of 5666 ft., where a 24-hr. gage through 1-in. choke showed 2640 bbl. of pipe line oil. The oil has a gravity of 28.0" A.P.I. and is brownish in color. Because of lack of pipe lines in the area, the wells are produced only for short periods of time, and it is predicted that development will be slow until the district is entered by pipe line purchasing companies. Von Ormy.—In March, 1934, Umbren et al. completed their Wentz

Jan 1, 1936

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967

For many years it has been known that large bodies of iron ore existed in Iron and Washington counties in Utah. The ore is chiefly hematite-both hard and soft-though some magnetite is found. No definite and complete estimate of the iron ore reserves of the state have been made. The U. S. Geological Survey estimated that 40,000,000 tons of ore were disclosed by development work averaging only 35 feet below the surface of the ore. The ore is found along an area about one and a half miles wide by twenty miles long, and for the most part on the eastern and southern slopes or foothills of Three Peaks. Granite Mountain and Iron Mountain. Later estimates by others have gone as high as ore in sight 164,000,000 tons, probable ore 300,000,000 tons and possible ore 1,000,000,000 tons. Whether this last estimate is too great or not there is sufficient iron ore in Utah to justify the starting of an iron industry. Two companies are now mining iron ore in Utah, the Columbia Steel Corporation and the Utah Iron Corporation. The mine of the Columbia Steel Corporation is at Iron Springs a few miles west of Cedar City. About 650 tons, of ore a day is being shipped to the blast furnace at Ironton. The ore is mined by the glory hole method. After being drilled it is blasted to the bottom of the several glory holes and is dropped through chutes into cars on the ore haulage level below. It is then hauled by electric locomotives to the crushing plant, where it is crushed to blast furnace size before going to storage bins. Some of the softer ore is brought to the chutes by Fresno scrapers.

Jan 1, 1925

By F. V. Lenel, G. S. Ansell

The creep behavior of an aluminum -aluminum oxide alloy, A T 400, fabricated by compacting an atomized aluminum powder, extruding the compact, cold working, and recrystallizing the extrusion, was investigated. This alloy has a dispersion spacing of 1 . Previously Ansell and Weertman determined the steady-state creep rate of a recrystallized aluminum-aluminum oxide SAP-type alloy, MD 2100, with a 0.48-p dispersion. This alloy was found to have a steady-state creep rate of less than 10-6 min-1, too small to be measured accurately. By employing a more sensitive method of measuring creep rate, it was possible to determine the steady-state creep rate of AT 400 alloy, which is somewhat faster than that of MD 2100, at a series of temperature and applied stresses. Above a stress of Burger's vector, A = dispersion spacing, u = is a shear modulus) the rate follms an equation of the type: Steady-state creep rate K = A exp. where A is a constant, Q is the activation energy for sey-diffusion, and is the applied stress. At stresses lower than the steady-state creep rate drops off sharply and is no longer in agreement with this equation. This behavior is in good agreement with that predicted by the model for dispersion strengthened alloys in the stress and temperature range investigated. The absolute value of the creep rate is, however, four orders of magnitude lower than that predicted if the normal number of active dislocation sources are assumed to be present. It is concluded that in this SAP-type alloy the usual three-dimensional dislocation network is not present. Instead, short dislocation segments extending from one dispersed particle and terminating at a neighboring particle may act as dislocation sources. With this provision the creep model proposed by Ansell and Weertman reasonably accounts for the creep behavior which was observed. RECENTLY, Ansell and Weertman1 proposed a dislocation model from which they derived creep equations to describe the steady-state creep behavior of dispersion - strengthened alloys. Following Schoeck,2 they assumed that the rate controlling process for steady-state creep is the climb of dislocations over the dispersed particles. In order to verify their creep model, Ansell and Weertman determined the steady-state creep behavior of an aluminum-aluminum oxide SAP-type alloy, MD-2100, in both the fine-grained as-extruded, and coarse-grained recrystallized conditions. Since the grain size was the order of the dispersion-spacing, their model was not applicable for the as-ex- truded alloy. It should, however, be applicable to the coarse-grained recrystallized alloy. The results they obtained were rather unexpected. No meas-ureable steady-state creep was observed for the recrystallized MD-2100 alloy. If their model is correct, and if the second-phase particles act solely to hinder dislocation motion, then some measureable steady-state creep would have been expected. On this basis, they postulated that, in this SAP-type alloy, the main effect of the fine dispersion was to inactivate dislocation sources rather than to hinder the movement of dislocations. In order to understand more fully this unusual creep behavior, and to determine the validity of the model proposed,' the steady-state creep behavior of an aluminum-aluminum oxide recrystallized SAP-type alloy, with a somewhat coarser dispersion spacing, was investigated. The results of this study are presented in this paper.

Jan 1, 1962

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress' four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver's new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers' courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952

By W. D. Faulkner, J. E. Urbanic, R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in carbon-in-pulp and carbon-in-leach circuits has been investigated. Carbons from two US mines, one Canadian mine, and a South African pilot plant operation were characterized before and after regeneration. Thermal regeneration of the carbon was investigated using factorial analysis to determine the effect of interaction of furnace temperature, retention time, and use of supplemental steam. The operation of acid washing the service carbon was investigated, including a comparison of the use of nitric and hydrochloric acids. The effect of quenching regenerated carbon was also briefly studied. Prom the data obtained, guidelines are given for effective regeneration operation.

Jan 1, 1986

By Peter N. Calder, G. H. Blackwell

The development of an open pit slope monitoring system, from equipment selection and justification to complete computer data storage and analysts, Is described. Methods of overcoming the Limitations of the electronic transit/distance measuring device and survey system selected are discussed. Results of the monitoring program showed that blasting was a major cause of Instability, and, after much experimentation, suitable blast patterns for mine production and pit wall integrity were designed. The experiences gained with double benching 'and wall cleanup procedures are discussed . The monitoring program also indicated that water was a contributor to instability, and methods of dealing with water In a rock with a low storage coefficient and transmissibility are described. Because of the danger of falling rock, photogrammetric methods are used for joint mapping and analysis, this work being contracted out. Joint strengths are measured on-site using a portable shear tester. Finally, a discussion of a complex failure is given.

Jan 1, 1983

By W. R. Hansen, F. W. Boulger

Twenty-nine laboratory steels were studied to determine the effects of composition and ferrite grain size on drop-weight and Charpy V-notch transition temperatures. The experimental steels covered the following ranges in composition.. 0.10 to 0.32 pct C, 0.30 to 1.31 pct Mn, 0.02 to 0.43 pct Si, md nil to 0.136 pct acid-soluble Al. Although most of the data were obtained on hot-rolled samples, some plates were heat-treated in order to cover a wider range in ferrite grain size. The experimental data were used for a multiple-correlation analysis conducted with the aid of an electronic computer. The study showed that carbon raises and that manganese, silicon, aluminum, and finer ferrite grains lower both drop-weight and Charpy transition temperatures. Quantitatively, variations in composition and grain size have a more marked effect on V15 Charpy transition temperatures than on the drop-weight transition temperature. Useful correlations were found between transition temperatures in drop-weight tests and those defined by seven different criteria for Charpy tests. Evidence was accumulated that the conditions ordinarily used for drop-weight tests are more severe for 1-1/4-in. -thick plate than for 5/8- to 1-in. -thickplate. PROJECT SR-151, to study quantitatively the effects of metallurgical variables on performance in the drop-weight test, was established by the Ship Structure Committee late in 1958 on recommendation of the National Academy of Sciences, National Research Council. This project was initiated as a result of the increasing use of the drop-weight (nil-ductility) test in predicting the ductile-to-brittle behavior of steel. Qualitative data indicated the drop-weight was not as sensitive to metallurgical variables as the Charpy V-notch test. Furthermore, the available information indicated that the drop-weight test did not show the superiority of killed steels over semikilled steels reflected by Charpy tests. This difference in sensitivity to brittle fracture is considered important because the drop-weight transition temperature has been reported1 to correlate better with service-temperature failures than the V-notch test does at a constant energy level. Therefore, this project was concerned with establishing quantitatively the effects of metallurgical variables in the drop-weight test. For comparison, Charpy V-notch data were obtained for the steels investigated. This paper summarizes the results of the investigation. Most of the steels used for the study were made and processed in the laboratory. However, some tests were also made on commercial killed steels available from Project SR-139 (SSC-141). During the course of the investigation, data were obtained on the effects of carbon, silicon, manganese, and aluminum on transition temperatures of drop-weight and Charpy specimens. In addition, the effects of heat treatment which changed the ferrite grain size and the transition temperatures were also investigated. Finally a few exploratory studies were made on commercial killed steels to evaluate the effects of plate thickness, grain size, and heat treatment on the performance of drop-weight specimens. EXPERIMENTAL PROCEDURES Preparation of Materials. A total of twenty-nine 500-lb induction-furnace heats were made and processed in the laboratory for the investigation. Carbon, manganese, silicon, and aluminum contents were systematically varied. Melting and rolling techniques proven satisfactory in a previous project2 were used as a guide for the current investigation. Composition. The composition of the twenty-nine laboratory heats made for this project are given in Table I. The steels are divided into three groups. The first group consists of ten aluminum-killed steels similar in composition to Class C ship-plate steel. The second group consists of ten semikilled or Class B type steels. In both of these groups the carbon and manganese contents were intentionally varied over a wide range. This wide range in composition was helpful in obtaining quantitative data from a limited number of steels. The primary purposes of these two groups of steels was to determine the effects of carbon, manganese, and deoxidation practice. In addition, one steel in each group (Steels 2-2 and 9-2) were made about 1 year after the start of the program in order to check consistency of melting practice. The third group of nine steels listed in Table I was intended for studies on the effects of silicon and aluminum. In eight of these steels carbon and manganese were held relatively constant at levels of about 0.2 and 0.8 pct, respectively, while silicon and

Jan 1, 1963

By P. Chiotti, J. T. Mason

Thermal, X-ray, metallographic, and resistivity data were obtained to establish the phase diagram for the Yb-Zn system. Six intermetallic compounds and five eutectics have been identified. The compounds position at 695°C. No evidence for the compound YbZn,, was observed. Whether this compound is stabilized or inhibited by small amounts of impurities is uncertain. SEVERAL aspects of the Yb-Zn system have been reported in the literature. Much of this work deals with the crystallographic identification of some of the compounds. The YbZn compound has been reported by Iandelli and palenzonal and the YbZn, structure and thermal data for the composition range between YbZn and Yb3Znll have been reported by Michel et al. A compound of uncertain stoichiometry in the range 60 to 68 wt pct Zn with a cubic structure has been reported by Kuz'ma et aL4 The YbzZn17, YbZn,,, and YbZn13 compounds have been reported by both Kuz'ma et a1 and Iandelli and Palenzona.' YbnZn17 has also been identified by Laube. This investigation was undertaken to establish the phase diagram of this system. Ytterbium in many respects behaves as an alkaline earth rather than a rare earth metal6 and it is of interest to note the resemblance between the Yb-Zn system, the Ca-Zn,' and typical rare earth-zinc systems.g'10 MATERIALS AND EXPERIMENTAL PROCEDURES The materials used in this investigation were Ames Laboratory ytterbium and Bunker-Hill slab zinc, 99.99 pct pure. Analyses of the ytterbium showed 38 ppm Ta, 82 ppm 0, and 15 ppm N with Ca, Cu, C, Mg, Al, Si, Cr, Fe, Ni, Sc, Y, Er, Tm, and Lu all less than 50 ppm. The ytterbium was dehydrogenated by heating in tantalum under vacuum for 8 hr at 900°C. The metal was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys in the composition range between ytterbium and Yb2Zn17. With higher zinc concentrations the tantalum was penetrated by the alloy and failed after several days at temperatures of 600" to 700°C. Approximately 20 g of zinc and ytterbium metal were sealed under argon in *-in.-diam tantalum cruci- bles equipped with thermocouple wells. The crucibles were in turn sealed in stainless-steel jackets. The alloys were equilibrated in an oscillating furnace and given various heat treatments in a soaking furnace. The steel jackets were removed and differential thermal analysis data were obtained under an atmosphere of argon. The thermal analysis apparatus was calibrated against the melting points of pure zinc, aluminum, silver, and copper and found to give thermal arrests within 1°C of the accepted melting temperatures for these elements. The thermal analysis apparatus has been described in an earlier paper.g Alloys were further heat-treated as necessary and subjected to metallographic examination and X-ray diffraction analysis. Most alloys were etched with Nital (0.5 to 10 pct nitric acid in alcohol). EXPERIMENTAL RESULTS The results of the thermal analysis are summarized by the points on the phase diagram, Fig. 1. Six compounds and five eutectics were observed. The eutectic temperature and compositions in weight percent zinc are 491°C and 12 pct, 645°C and 32 pct, 687°C and 54 pct, 742°C and 67 pct, and 750°C and 77 pct. The compounds YbZn, YbZn2, Yb2Zng, Yb2Zn17, and YbZnll melt congruently at 650°, 751°, 75Z°, 754", and 755"C, respectively. The compound Yb3Znll undergoes a peritectic decomposition at 695°C. The transformation and melting temperatures for the ytterbium were observed to be 797" and 817°C. re-

Jan 1, 1969

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By W. A. Alexander, L. M. Pidgeon

Metallic magnesium and similar meta!s near the top of the electromotive series have been commercially produced by the electrolysis of a suitable molten salt. Despite the success of electrolysis, sufficient inherent objections exist to justify the search for a direct reduction method. Such a method would widen the choice of raw materials, relax the rigid electrolytic requirements of raw-material purity, and, by obviating direct current, over simplicity of plant equipment. This paper describes the pilot-plant development of one such method, which has subsequently formed the basis of operation of six commercial plants-—one in Canada and five in the United States. Unlike aluminum, magnesium is volatile at relatively low temperatures. This physical property, which produces its greater inflammability, also offers possibilities of direct reduction that are not available with aluminum. In the basic reaction MgO + X = XO + Mg if X is nonvolatile, the reaction may be forced to the right at high temperatures by the evolution of magnesium vapor, despite the large negative value of the heat of reaction which is almost bound to follow the use of any available commercial reducing agent. The cheapest X, of course, is carbon, but this notable advantage is modified by the production of a volatile oxide CO, so that both Mg and CO are evolved simultaneously. Elaborate devices are required to shock-cool the equilibrium mixture in order to prevent back reaction. At best, a pyrophoric powder is produced, requiring redistillation to provide marketable metal. The practical development of this process, is due to F. Hansgirg, and his methods have recently been given a trial on a grand scale in the plant at Permanente, California, and smaller plants were previously built in Austria, England and Japan. A second class of reducing agents is available, those which produce nonvolatile oxides. When XO and X are relatively nonvolatile, magnesium is the only volatile member of the system. It may be evolved in a simple distillation step and condensed without the formation of powder. Two basic requirements must bc fulfilled in order that such a reaction may proceed: I. The reducing agent when heated to a reasonable temperature in presence of MgO must cause the production of an appreciable equilibrium vapor pressure of magnesium. This magnesium must be removed continuously. z. A supply of heat must be maintained. In order to fulfill the first requirement, operations must be conducted in vacuo or in a stream of Hz. Owing to its greater efficacy and relative safety, vacuum has been employed in the work to be described. The choice of a suitable reducing agent formed the subject of an extensive series

Jan 1, 1944

By G. R. M. Del Giudice, A. F. Taggart, Othon A. Ziehl

In a previous paper1 in which one of the authors collaborated, it was postulated that All dissolved reagents which, in flotation pulps, either by action on the to-be-floated or on the not-to-be-floated particles affect their floatability, junction by reason of chemical reactions of well recognized types between the reagent and the particle affected. This generalization, apparently, like many pioneer structures, had for certain observers a flimsy appearance, and these, judging its stability rather by the number than by the character of its foundation posts, have attempted variously to overthrow it, either by the frontal attack of general denial, or by the flanking movement involved in assuming that those cases in which the facts were unknown or unproved were, therefore, discordant. But as time has passed and further evidence on the question has accumulated, it has become apparent that the results of verifiable experiments add stone by stone to the substructure of the hypothesis, and that the super-tructure has lost nothing in weathering. The present paper constitutes an examination of the opposing positions in the light of the more recent evidence developed. It will clarify the discussion if, at this point, we state more fully the implications of the disputed hypothesis. In the first place, it is explicitly limited to reagents that are dissolved in the water of the flotation pulp. Next, it refers only to such of these dissolved reagents as act on the solid particles in the pulp to affect their floatability. This includes the collectors, activators, and certain depressors and gangue-control reagrnts, but not the pure frothers, and not, necessarily, conditioners whose function seems to be merely that of pH control, although in certain cases it has been demonstrated that such control has the effect of regulating the primary reaction of the collector, depressor, or the like. Finally, there is no limitation as to the nature of the chemical reaction postulated.

Jan 1, 1935

By E. J. Haug, M. M. Fine

FOR several years work has been carried on by the U.S. Bureau of Mines at Rolla, Mo., to develop improved methods of concentrating the oxidized ores of lead and zinc. Various samples have been investigated, and results on some have been published 1,2 lished.l, 2 Details of the progress to date are given in a mineral dressing study now being conducted for an extensive oxidized lead-bearing tract in southeast Missouri, property of St. Joseph Lead Co. These oxidized ores present problems typical of many encountered in modern mineral dressing research in that recovery of very fine particles is of

Jan 1, 1956

Secretary Membership Committee Increase of Membership Papers and Publications Committee Library Committee Treasurer Report of the Secretary TO THE BOARDOF DIRECTORASN D THE MEMBEROS F THE AMERICANIN STITUTE OF MINING AND METALLURGICAENL GINEERS GENTLEME:N As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining industries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has restricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metallurgy have a greatly increased necessity for i,dormation and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowledge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrolment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1928

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921