Search Documents

By Walter S. Weeks

The process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the JouleThompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. C, Specific heat of air at constant volume, B.t.u. per lb. per deg. F. C, Specific heat at constant pressure, B.t.u. per lb, per deg. F. T1 Absolute temperature of air in pipe, deg. F. T8 Absolute temperature of air outside after expansion and mixing and coming to rest. j Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By F. F. Aplan

INTRODUCTION Coal is a solid combustible mineral substance resulting from the alteration of vegetable matter largely in the absence of air. It occurs in nature with varying percentages of mineral matter associated with and incorporated into the coalified material. If the amount of this inorganic mineral matter is sufficiently small, and if selective mining can be practiced so as to avoid the incorporation of ash- bearing material from adjacent strata and/or parting seams, the coal can be used as-mined. Otherwise, it must be given a preparation treatment. In 1980 the bulk of the approximately 525 coal preparation plants were located in the eastern half of the U.S., largely in the Appalachian and to a lesser extent in the midwest coal fields (1). Only 17 of these preparation plants were located in the west; these were in Colorado, New Mexico, Utah, Washington and Wyoming. In the past, however, a great many more preparation plants were operated in these and other western states. The upsurge in both the domestic and world- wide demand for quality coking and steam coal will certainly lead to an increase in the number of preparation plants in the west. In fact, there has been a massive development of coal mines and their associated preparation plants across our northern border in Alberta and British Columbia, largely to serve the export coking and steam coal market. Most of the tremendous increase in newly-mined coal in the western U.S. has come from thick seams of inherently low-sulfur, low- ash coal, easy to mine selectively without significant contamination with ash-forming minerals and requiring no preparation. Because of

Jan 1, 1983

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of' impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company's Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By A. L. Mular

lnput energy-size modulus relation at small reduc-tion ratios is expressed by Et = (M, -Mt) k;. In some cases 13 is close to Schuhmann's distribution modulus a in value. Experimental results in conjunc-tion with the equation demonstrate the fact that energy input which produced fracture is not expended on unbroken starting material inside the mill at any time. Recently, schuhmann1 derived the Charles equation2 using the postulate that complex com-minution operations can be considered as a summa- tion of many comminution events. The fragments resulting from each event are assumed to follow the Gaudin-Schuhmamn distribution. In his derivation, Schuhmann implies that the size distribution of the total mass of a material is determined by the fraction of that mass actually subjected to comminution. Consider a feed to contain a volume, Vo, of uni- formly sized homogeneous material. After t seconds of grinding, let the volume of broken material be Vo - Vt where Vt is the volume of starting material not yet broken. The size distribution of the broken material is given by: where V is the cumulative volume less than size X, and k, is the size modulus of the broken material at time t. The distribution for the total volume at this

Jan 1, 1962

By Joseph Chalmers

The Petroleum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., has for the past three and a half years maintained a laboratory with the necessary personnel for conducting research on methods of increasing the recovery of oil. Some of the preliminary problems encountered in starting this work, with the data obtained, were discussed in A. I. M. E. Technical Publication No. 144, "Oil Recovery Investigations of the Petroleum Experiment Station of the U. S. Bureau of Mines," which was presented at the October meeting of the Institute at Tulsa, Okla., in 1928. Scope of Paper The following discussion gives some of the results of the more recent work at the Oil Recovery Laboratory. These experiments were conducted to obtain laboratory data pertaining to the relative merits or efficiencies of various pressure media in the recovery of oil from a sand reservoir. Two general types of experiments were conducted. In one the various pressure media were passed through an artificial body of sand partly saturated with oil at a constant input pressure; in the other the pressure media were passed through the body of sand partly saturated with oil at a constant volume rate. No attempt will be made to discuss the ramifications of economic problems which enter into the choice of a pressure medium. Apparatus and Materials The two 6-in. by 6-ft. flow tubes described in Technical Publication 144 were used in these experiments. They consist of 6-ft. sections of 6-in. casing with a blind flange at each end. There are three 1-in. well openings in each tube, spaced 2 ft. 4 in. apart, the end wells being

Jan 1, 1930

By W. C. Clarke

An empirical study of the nature of the embrittle-ment which occurs in martensitic and semiaustenitic precipitation hardening stainless steels upon exposure at temperatures of from about 550" to 875°F has been undertaken. This work was aimed at determining cazusation and means of controlling this phenomenon. A commercial copper bearing precipitation hardening alloy was used as a basic material for study. The effect of heat treatment variables was studied as was the effect of variations in analysis. It is concluded from the evidence that martensitic and semiaustenitic precipitation hardening stainless steels are subject to 885°F ernbrittlement similar to that observed in the straight chromium stainless steels. A characteristic of precipitation hardening stainless steels which has limited their use in certain applications is that they embrittle when held at temperatures in the range of from about 550" to 900°F. This is true to a more or less degree in all currently available alloys, either the basically martensitic type or the semiaustenitic type. The rate of embrittlement varies markedly with exposure temperature, being low at 550" to 600°F and in-creasing as the temperature increases. In spite of this embrittlement, these alloys with their unique combination of high mechanical strength, reasonable toughness, and good corrosion resistance are used in many hundreds of applications. Nevertheless, there are potential applications where the embrittle-ment described is a limiting factor. The purpose of this investigation was to study the embrittlement of these alloys and to find a way to control or eliminate it. GUIDELINES USED IN PRESENT WORK The work reported in this paper is based on a study of 17-4 PH*, a very widely used alloy. It has been used *Trademark of Armco Steel Corp., licensor. in pressurized water and boiling water atomic reactors operating at about 550°F for a number of years. As the life of such equipment is extended or operating temperatures are raised, the possibility of embrit-tlement becomes of increasing concern to materials engineers. Much investigation work was done with respect to the use of 17-4 PH at 550°F. K. C. Antony' states "Such estimation" (of an activation energy for the diffusion of chromium in iron) "would indicate W. C. CLARKE, Jr. is Senior Research Engineer, Advanced Materials Division, Armco Steel Corp., Baltimore. Md. This manuscript is based on a talk presented at the symposium on New Developments in Stainless Steel, sponsored by the IMD Corrosion Resistant Metals Committee, Detroit, Mich., October 14-15, 1968. significant secondary aging is improbable at temperatures less than 700°F within normal component service life". This statement is modified however by the recognition of the accelerating tendencies of applied stress and internal stress as well as the possible effect of irradiation. In this investigation of 17-4 PH, the H 1100 (1900°F-1 hr oil quench or air cool + 1100°F-4 hr-air cool) condition was used, partly because this condition is normally used in atomic reactors. As shown later, the precipitation hardening temperature has no real bearing on the rate of embrittlement. An exposure temperature of 800°F was selected since embrittlement at 800°F is rapid, permitting development of relative data in time periods of 400 to 500 hr. For those not familiar, a nominal present day analysis of 17-4 PH is: C Mn P S SiCrNiCuCbN 0.04 0.30 0.015 0.015 0.60 16.00 4.30 3.25 0.23 0.030 TYPICAL BEHAVIOR OF 17-4 PH Figs. 1 and 2 show the behavior of a commercial heat of 17-4 PH under the conditions defined. Characteristically, 800°F exposure causes a rapid drop in Charpy V-notch impact strength. Tensile and yield strengths gradually increase and a gradual loss of elongation and reduction of area occur, accompanied by an increase in hardness. Notched tensile strength increases to 125 hr exposure and then sharply decreases after exposure for 500 hr. The notched vs un-notched tensile ratio remains virtually constant to exposure for 125 hr (1.67 to 1.56) but drops to 1.15 after 500 hr. Tensile ductility is not alarmingly affected even after much longer exposure times than these. For example, samples aged at 1100°F for 1 hr exposed at 800°F for 4000 hr showed a drop in elonga-tion of from 13 to 11 pct and in reduction of area of from 58 to 37 pct. Notched impact is the property SmIgth KSI 3JJ[/__________^UTS-Nrteh 260 ;/- 240 —^ 200 UTS-Smooth________._, o ioo mo Sob" m Too Hours Exposure Fig. 1—Effect of exposure at 800°F for various times on notched tensile strength and smooth tensile and 0.2 pct yield strength of 17-4 PH in the H 1100 condition.

Jan 1, 1970

[ ]

Jan 1, 1938

By Frederik P. Agterberg

This paper deals with frequency distributions in the field of mineral resource evaluation when a grid is superimposed on the study area and metallogenetically significant attributes are coded with respect to the cells of the grid. It is shown that the parameters of a negative binomial distribution for frequency of mineral deposits per cell can be derived from the parameters of a gamma distribution for the coded attributes. It is also shown that an exponential model for spatial correlation of cell values and Matheron's discrete Gaussian model for indirect transfer functions may provide a suitable methodology for relating cell value distribution to cell size.

Jan 1, 1977

By Oswald J. Heinrich

THE great improvements which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance must be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for ex¬ploration at least, we may assert this rule Any borehole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and * The drawings illustrating this paper are one-half the size of the tools represented, with the exception of the instrument used to reverse the current in the bore-hole (Fig. 17), which is one-third the actual size.

Jan 1, 1874

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By Walter S. Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case 1 If compressed air is allowed to expand to the atmospheric pressure through an orifice in an sir line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. Cv Specific heat of air at constant volume, B.t.u. per lb. per deg. F. Cp Specific heat at constant pressure, B.t.u. per lb. per deg. F. T1 Absolute temperature of air in pipe, deg. F. T3 Absolute temperature of air outside after expansion and mixing and coming to rest. J Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By John V. Beall

Cutting costs and increasing safety with new ideas is the byword with The Cleveland-Cliffs Iron Co. on the Marquette Range in Michigan. Among the new ideas being tried out are mechanical shaft mucking, prefabricated lagging to replace timber poles, Carset bits in shaft sinking, and rubber tired guide wheels on the ore skips. Plans are being made to stockpile ore with conveyor belts during the winter. In sinking the Mather "B" Shaft a 3/8-yd clamshell-type bucket is used for mucking. The clamshell is opened and closed by means of a verticallymounted hydraulic ram actuated by 5000 psi oil pressure. An Ingersoll Rand-type hoist is used to raise and lower the clamshell. The hoist is controlled by one member of the crew on the floor of the shaft. When the bucket is raised, the men swing it over the muck pile to the desired position and then it is lowered on to the broken rock. The 1400-lb weight of the bucket causes it to sink into the broken rock and it digs as the ram closes the bucket. The hydraulic ram is operated by a man on the lowest shaft steel set who controls a specially designed oil pump which supplies oil pressure. The clamshell is emptied.

Jan 1, 1949

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

By W. L. Zeigler

THE gravity concentrator of the Hecla Mining Co. was originally constructed in 1888 by the Milwaukee Mining Co., which was operating the Gem of the Mountains mine. It was purchased by the Hecla Mining Co. in 1900, and placed in operation 2 years later. At that time FIG. 1.-HECLA MINING CO. GEM CONCENTRATOR, GEM, IDAHO. the capacity was only about 200 tons a day, but many additions and changes in equipment have been made so that the present capacity is about 800 tons. One of the outstanding improvements made was the substitution of Callow flotation cells for vanners, which occurred in 1915. The recent building of a flotation plant for treating jig tailings, and the construction of a modern surface plant at the mine, following the

Jan 1, 1927

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.o.b. mines, the output in 1948 was 1,568,848 tons worth $19,756,738.

Jan 6, 1950

By F. J. Smit

The Tintic Division of Kennecott Copper Corporation operates the Burgin Mine in the East Tintic District near Eureka, Utah, approximately 75 miles south of Salt Lake City. The Division was organized in 1963 to develop concealed replacement orebodies in the area located by Bear Creek Mining Company, Kennecott's domestic exploration subsidiary. Several accounts of the discovery of these orebodies and the general geology of the area have been given (1, 2). The ore is very complex and of varying degrees of oxidation and alteration. The principal metal values are lead, zinc, silver, and cadmium. The Burgin No. 2 shaft was sunk in 1963 to provide access for mining the orebodies. Much of the ore mined after this shaft was sunk was high grade and shipped directly to smelters, but concurrently it was recognized that concentration would be required to upgrade the lower grade ore in the deposits. Accordingly, in January 1967, authorization was received to construct a 500 tpd concentrator. From the beginning it was expected that the characteristics of the mill feed would vary widely and unpredictably as mining progressed. This paper summarizes the characteristics of the ore, the test work upon which the plant design was based, the engineering and construction, and the present operation of the facility eighteen months after startup. ORE CHARACTERISTICS The Burgin ore is a complex assemblage of minerals from replacement of limestone. The replacement and alteration occurred in at

Jan 1, 1970

By Jasper L. Stuckey

It is not known when kaolin mining was first begun in North carolina, Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some Of the early English porcelains. In 1744,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply Of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage Of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. 'Or some 20 years, kaolin mining was carried On chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 Yea's most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. Distribution The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Ire-dell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. Geology With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1948

By Jasper L. Stuckey

It is not known when kaolin mining was first begun in North carolina, Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some Of the early English porcelains. In 1744,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply Of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage Of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. 'Or some 20 years, kaolin mining was carried On chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 Yea's most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. Distribution The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Ire-dell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. Geology With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1948

By J. A. Knox, R. M. Lasater, J. M. Tinsley

Chemical squeeze treatments have been used to provide temporary relief from certain production problems. The chemical fracture-squeeze technique, combining the effects of a fracturing treatment and a squeeze operation, has been more successful than conventional squeeze operations. Knowledge derived from well stimulation and reservoir engineering research provides a means for predicting the theoretical effective life of such a treatment. Analysis of theoretical equations and concepts developed allows selection of improved treatment techniques based on specific formation conditioins. Theory used in this analysis was developed as an extension of previous electrical model studies made to establish the expected flow and pressure profiles adjacent to a fracture system. The chemical fracture squeeze technique can be utilized in the economic application of corrosion inhibitors, emulsion breakers and paraffin and scale inhibitors. Application of this technique is shown to be effective. The slow return rate of injected chemicals, controlled by the resultant flow profiles and treatment variables, permits extended periods of chemical effectiveness. Results of field treatments are given, showing that the concepts outlined above for chemical fracture-squeeze treatments are valid and that applying this technique can help alleviate many current production problems. INTRODUCTION Much progress has been made in the last 10 to 15 years in developing chemicals for use in stimulating wells, maintaining production and protecting well equipment from damage due to corrosion. Not too many years ago, some wells seemed to dry up or wear out. In many cases the wells were produced as long as possible without any attempt at maintaining productivity. Even with the advent of new and better stimulation techniques, a rapid decline in production was observed. Methods of removing and, in some instances, preventing damage have been developed. Among thosc factors responsible for uneconomical production are scale, paraffin, corrosion, bacteria, water blocks and emulsions. Soluble scale-prevention chemicals have been developed1,2 that can be placed in a formation along with frac- turing sand. As the water produces back across this bed, the solid material dissolves slowly and can provide long-term protection from scale. However, bottom-hole temperature and salinity of produced water vary widely and both these factors influence the rate of solubility. Scale inhibitor composition is also a controlling factor. Some of the solid material may be crushed, increasing the surface area exposed to water and increasing the rate at which it dissolves. Some of the material may never be contacted by water and can be lost. However, this type of treatment has been very successful in many instances and has helped maintain economical production for extended periods of time. Liquid scale inhibitors, which are more widely applicable and more stable, have been developed in recent years; however, because they are liquids, their use has been restricted to treatment down the annulus, using metering pumps to provide proper concentrations in the produced fluid. This has prevented use in wells containing packers, in dually completed wells and in gas-lift and flowing wells. Wells that operate with an open annulus may also experience severe corrosion problems due to introduction of oxygen. Paraffin inhibitors3 have been developed that can be fractured into a well as particulate solids to be slowly dissolved in the produced fluid. These materials are not usually effective in wells with a bottom-hole temperature in excess of 120F since solubility rate may be too fast if that temperature is exceeded or if aromatic content of the oils is unusually high. Corrosion inhibitors have been developed that can be fractured' into a well for long-term feedback, but development of a material with proper solubility or feed rate has been difficult. Corrosion inhibitors are available in many different forms. Liquids have been lubricated down the annulus or sticks or pellets dropped down tubing. Inhibitor squeeze treatments5 devcloped a few years ago led to development of inhibitors with particularly strong film-forming properties.6,7 This technique basically involves displacing a highly concentrated solution of the inhibitor into the formation through the tubing. Kerver and Hanson8 studied the adsorption properties of inhibitors on various types of formations. They showed that, even though the inhibitor was displaced radially into the true permeability, it could be produced back for a long period of time because of slow desorption from the rock. Methods developed for monitoring the return of these inhibitors generally have established 1 to 6 months as the effective limit before retreatment is necessary.9 Inhibitors displaced into the interstices of the formation sometimes cause emulsions that either hamper production or cause treating problems on the surface.