Search Documents

By S. H. Williston

IT is not often that bore hole surveys can be checked by actual civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bisbee, Ariz., drilled a 1245 ft, 8 in. diam, churn drill- hole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in- the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Be- cause of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results ' of doubtful value.

Jan 1, 1950

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By Charles G. Maier

It has long been supposed that when crystalline materials are comminuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1.t The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chemical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the corrected heat of solution was less for fine material than for coarse. Continuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by Rosenhain and Stott4 and by Taylor and Quinney9 The results obtained by the different investigators were not satisfactorily consistent, but the experiments of Taylor and Quinney constitute by far the best figures obtained to date. The previous paper1 presented evidence to show that if energy is stored in the surfaces of crystals the densities of fine crystals should differ

Jan 1, 1936

By M. H. Merriss

IN THE last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: In the series system, the electrodes in a single tank are in series, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 6, 1925

By A. N. Diehl

IT is the object of this paper (1) to deal with the elements in blast-furnace gas from the standpoint of their importance, and the part they are to play in future consumption, and (2) to give detailed information about the construction and operation of a plant designed among the first in this country for washing gas on a large scale.

Jan 5, 1914

By F. F. Peng, A. D. Walters, M. R. Geer, J. W. Leonard

INTRODUCTION Washability characteristics derived from float-and-sink analysis in Chapter 4 demonstrate that coal is intrinsically heterogeneous, and this heterogeneity is also evident in the proximate, ultimate, and size analyses. A range of particles from high to low specific gravity is usually seen in the run-of-mine coal. One objective of coal preparation is to recover the high quality float material (the particles of lower specific gravity) such that the recovered product meets certain quality specifications, as well as to reject or recycle low quality particles of higher specific gravity. The maximum recovery of cleaned coal at the required quality is of major concern to plant operators. However, the quantity and quality of products of coal cleaning, determined in the operation of actual commercial cleaning plants and by theoretical calculation based on run-of-mine washability studies, are known to be different with each coal. Therefore, during the last half century, coal preparation engineers have repeatedly sought methods to predict the technical and economical efficiency of separation of cleaning equipment and systems. Many formulas have been proposed by international investigators to evaluate the efficiency of various coal cleaning operations, primarily based on the yield and/or ash of the various products of coal cleaning. Performance criteria in use today are capable of defining all of the important aspects of a given concentrating operation; however each criterion has certain restrictions or limitations. It is important, therefore, to understand how such formulas can be used and the problems involved in their construction. Technical Measure of Plant Performance Conventional means for evaluating a preparation plant's performance are generally approached through the use of equipment performance mea-

Jan 1, 1979

By D. C. Seidel, M. C. Fuerstenau, R. J. Roman

The existence of a surface charge on the alkali halide salts is shown, and a flotation mechanism involving surface charge and collector solubility is developed. Data suggest that KC1 is positively charged and that NaCl is negatively charged in saturated brines, and that the neutral molecule RNH,Cl is the collector in the amine-KC1 system, RSO, is the collector in the sulfonate-KC1 system, and RCOONa) is the collector in the fatty acid-NaCl system. A number of hypotheses have been advanced to explain the mechanism of soluble salt flotation; one of these involves exchange between collector ions and surface cations. With this mechanism Gaudin1 suggested that the differences in flotability of halite and sylvite with primary amines are due to the ionic size of the RNH;, Kt, and Na t ions. Fuerstenau and Fuerstenau expanded this hypothesis to include many other alkali halide salts. Several exceptions to this hypothesis are known. That is, this model does not explain why salts containing the same cation, or why salts of different degrees of hydration, respond differently to flotation. For example, why NaI is floated with an amine whereas NaI .2H,O is not. Further, no correlation between ionic size and flotation response can be made with sulfonate or car-boxylate as collectors. In addition, this hypothesis does not explain the effect of magnesium or lead activation, nor does it offer any explanation of the role of temperature in salt flotation. Rogers and Schulman3 realized some of the inadequacies of the ion exchange mechanism and proposed another mechanism based on the heat of solution of the salts. They concluded that weakly hydrated salts can be floated with alkyl amines and sulfonates, that strongly hydrated salts can be floated with fatty acids, and that excessively hydrated salts cannot be floated at all. Their work was not limited to the al-

Jan 1, 1969

By W. B. Price

AT the New York meeting of the American Institute of Mining-and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."§ The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. PROTUBERANCES ON ADMIRALTY BRASS In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig.. 1a) and upon analysis was found to contain 66.66 percent. copper, 4.02 per cent. tin and .03 . per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and .01 per cent. lead. A sample of the shaggy-rough protuberances at the -very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had -revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation."

Jan 10, 1926

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack-poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet-for indeed the instrument is easier levelled, and, more-over, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity ; on the other hand, however, that correction

Jan 1, 1873

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope ; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet for indeed the instrument is easier levelled, and, moreover, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure Any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity; on the other hand, however, that correction

By W. F. Chiao

With the application of dislocation damping theory an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. A ductile steel was compared with a brittle stee1 by simultaneously measuring the ultrasonic attenuation and velocity during tensile test, and the density of free dislocations and their mean loop length were then calculated as a function of strain. The results showed that in the ductile steel there was always a large generation of dislocations and great extension of loop length occurring at some stage within the early plastic region. In contrast, the brittle steel showed very little or no such sudden changes in dislocation dynamic states after the onset of plastic deformation. Furthermore, a strong temperature dependence of dislocation dynamic states was also observed in the ductile steel and a hypothesis was suggested that a thermally activated process of dislocation rearrangement could occur at higher deformation temperatures. The activation energy of dislocation rearrangement at room temperature was estimated as about 2030 cal per mole.C. DUCTILITY is an indispensible property in the application of engineering materials, especially steel. During the past two decades the theoretical and experimental approach to the understanding of flow and fracture of metals has been constantly undergoing changes and progress." while the fracture behavior of metals can be influenced by many factors such as chemical Composition,3 second-phase particle mor-phology,4 and dislocation arrangement,5 it is now a general belief that the fundamental understanding of the ductile-brittle fracture phenomena of solid materials must stem from the study of dislocation dv-namics developed under stress conditions.6,7 Most of the traditional ductility tests, such as Charpy impact test, slow bend test, and tensile fracture test, cannot by themselves reveal directly the mechanisms of ductile to brittle transition of materials. In the experimental investigation of tensile ductility it would be ideal to be able to study directly the dynamics of dis-locations in a bulk specimen during the process of deformation. Since the ultrasonic pulse technique is the only satisfactory method for studying dislocations and the fine details of deformation characteristics in metals in the course of a tensile test, it would appear that a comparative study of ultrasonic attenuation changes during tensile tests of metallic materials exhibiting different ductility might be very informative. So far no work comparable to this study has appeared in the literature. Recent progress in both theory and experiment has indicated the feasibility of studying the dislocation mechanisms of ductility behaviors by ultrasonic measurements during tensile test. Granato and Lucke8 have developed a quantitative theory that enables the calculation of dislocation density and their average loop length from the measurements of ultrasonic attenuation and velocity, and several investigators, including Chiao and Gordon,9'10 have shown that simultaneous ultrasonic measurements can be successfully made during a tensile test. Furthermore, many investigators11-13 have repeatedly proposed in the past several decades that deformation and fracture are mutually self-exclusive, and that the ability or inability of a material to deform plastically, i.e., to generate dislocations, is a major factor in determining whether the material will be ductile or brittle. Thus, in the present work an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. This article is principally concerned with the study of the relation between the propagation of ultrasonic waves and tensile deformation in a steel series which displays quite different toughness at room tempera-turk. changes in attenuation and velocity of ultrasonic waves have been measured as a function of strain during the deformation process. The results have been interpreted in terms of the vibrating string model for dislocation damping as developed by Granato and Lucke, and it has been found that some of the more subtle predications of the model are in good agreement with the experiments. This would be especially meaningful because most of the previous experiments in testfying the model were carried out with single crystals of high-purity materials and little work has been done with polycrystalline steel alloys. EXPERIMENTAL PROCEDURES AND RESULTS Specimen Materials. The tensile specimens used throughout this experiment were of two compositions selected from a series of Fe-Mo-0.77 pct Mn-0.22 pct C steels prepared for a ductile-brittle fracture transition study. One steel contains 0.21 pct Mo and the other 1.03 pct Mo. These two compositions were chosen for the present study because they possess quite different toughness properties at room temperature. The 0.21 pct Mo steel is quite ductile while the 1.03 pct Mo steel is rather brittle, as measured by the standard Charpy impact test. The alloys had been prepared by vacuum induction melting and chill casting in steel molds. The ingots were hammer-forged into 1/2-in.-sq bars from which tensile specimen blanks were cut. These blanks were first normalized under argon atmosphere at 1700°F and then reaus-tenitized and isothermally transformed at 1050°F to a bainitic microstructure. The chemical compositions, heat treatments, hardness measurements, and Charpy transition temperatures of the two steels are listed in Table I.

Jan 1, 1970

By R. Schempp

DURING the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these char-acteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and empha-sized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent cart on. The discrepancies encountered in the determination and classification of the austenitic grain size led to in investigation of some of the variants influencing the austenitic grain size as determined by standard methods.

Jan 1, 1937

By W. R. Johnson

In the spring of 1935 the writers undertook to compare the geomagnetic and direct-current earth-resistivity methods of tracing a concealed dike along its strike. As far as they are aware no such direct test has been attempted.# The area surveyed lies along United States Highway number 15 about one and one-half miles east of Chapel Hill, North Carolina, and northeast of Bolin Creek (Fig, 1). To the south of the highway is the flood plain of Bolin Crook, and to the north is a hill that rises almost to the elevation of Chapel Hill. A diabase dike, which strikes slightly west of north, out-crops in a. gully just south of the highway. Southward it has been covered by alluvium but northward outcrops again on the southeastern slope of the hill north of the highway. South of the highway the country rock is Triassic shale and sandstone, the northern limit of which is slightly north of the road. On the Geological Map of the United States I the pre-Triassic formations are shown as lower Glenarm and assigned a pre-Cambrian age. Since the ago of the Glenarm has been called into question in Pennsylvania 2, the writers prefer not to commit themselves as to the ago of these rocks further than to say that they are definitely pre-Triassic.

Jan 1, 1937

PRESIDENT GEORGE OTIS SMITH, District 4 WASHINGTON, D. C. PAST PRESIDENTS SAMUEL A. TAYLOR, District 3 PITTSBURGH, PA. E. DEGOLYER District 0 NEW YORK, N. Y. FIRST VICE-PRESIDENT W. H. BASSETT District 1 WATERBURY, CONN. TREASURER KARL FILERS NEW YORK, N. Y.¬ SECRETARY H. FOSTER BAIN NEW YORK, N. Y.

Jan 1, 1923

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di'rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956

By C. Schlumberger

SINCE the, beginning of the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.1 Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods.

Jan 1, 1932

By Rudolf Gahl

THE history of flotation in America is very short, at least as far as the large-scale application of the process is concerned. It is remarkable how many important developments have taken place inn the last few years and are already being extensively utilized. What was new a year ago, seems almost commonplace now. For this reason it is with hesitation that I follow the suggestion: of Dr. Ricketts, President of the Institute, to describe the experiences of the Inspiration Consolidated Copper Co. with the flotation process. TESTS CONDUCTED IN SMALL TEST-MILL When the Inspiration company first decided to build a concentrating plant, nothing was known about flotation, and the process was to be gravity concentration pure and simple. Demonstration Tests Conducted by Minerals Separation Co. While plans were being prepared by H. Kenyon Burch (who had been intrusted with the design and construction of the concentrator) the Minerals Separation Co., a concern at that time little known in America, asked and obtained permission to demonstrate the value of its flotation process for Inspiration ore. As. a consequence, a small 50-ton flotation machine of standard design was added to the company's test plant and started to operate in the beginning of 1913. This marks the beginning of flotation at Inspiration. The results obtained with this machine, which was operated by members of the Minerals Separation staff, so far surpassed what this company anticipated that it was decided to continue flotation tests for this purpose, and two of the flotation experts of the Minerals Separation Co., I. L. Greninger and G. A. Chapman, were retained. L. R. Wallace, now superintendent of the Miami works of the International Smelting Co., was at that time metallurgist of the Inspiration company and in that capacity took an active part' in these tests. Great credit is due to him for his quick recognition of the possibilities of flotation.

Jan 9, 1916

By M. J. Stewart, F. Weinberg

PREVIOUS investigations into convective flow in molten metals have examined systems in which the length-to-height ratio of the enclosure is large, usually using long graphite boats.''2 In normal castings this ratio is generally small and it is not possible to extrapolate the results of previous work to casting configurations. The present investigation was undertaken to examine liquid flow in systems of low length to height ratio. The apparatus used for the experiments is shown in Fig. 1. The molten zone of tin is contained in an aluminum mold of inside dimensions 6.4 by 6.4 by 0.31 cm. A heating block containing a resistance coil is attached to one end of the mold and a cooling block is attached to the other end. These are used to produce a wide range of temperature differences across the mold. The mold is contained in a stainless steel tank which is heated from the outside by resistance heaters to give the required operating temperature during the experiment. Temperature measurements in the molten tin are made with an iron-constantan thermocouple PT equal to 5 atm. The phase diagram derived by us was the same as that found by Krivsky and Schuhmann, except for a similar discrepancy in one boundary line representing the gas composition in equilibrium with SO a. The vapor pressures of the pure components can be neglected at 1700°K, 1 atm and 2500°K, 5 atm. There-fore, in these cases PT is essentially the total pres-sure in the system. This is valid for all the diagrams presented by Krivsky and Schuhmann except for the one at 2500°K and 0.01 atm, where the vapor pressure of silicon is comparable to PT.6 This work was supported in part by the American Iron and Steel Institute. 'C. E. Wicks and F. E. Block: Thermodynamic Properties of 65 Elements, U S. Bur Mines, Bull. No. 605, 1963. R. P. Elliott: Constitution of Binary Alloys, 1st supplementary, McGraw-Hill Book Co., New York, 1965. 3W. A. Krivsky and R. Schuhmann, Jr.: Trans. TMS-AIME, 1961, vol. 221, pp. 898-904. 4M. F. Ancey-Moret, M. Olette, and F. D. Richardson: Mem. Sci. Rev. Met., 1964, vol. 61, pp. 169-76. 5J . F. Elliott and M. Gleiser: Thermochemistry for Steelmaking, vol. 1. Addison-Wesley, Reading, Mass. 1960. 6 J.Drowart, G. De Maria, and M. G. Ingraham: J. Chem. Phys., 1958, vol. 29, p. 1015. probe of 0.4 mm diam inserted into the open top of the mold. Radioactive sn113, in the form of a small sphere, was gently lowered into the molten tin at point A in Fig. 1 THERMOCOUPLE> WATER ARGON END HEATER QUENCH ARGON Fig. 1—Apparatus for detecting liquid flow. Point A indicates position the tracer was introduced.

Jan 1, 1970