Search Documents

By S. R. Elliott

The Spies mine is located in the eastern half of the northwest quarter of section 2443-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope. From crosscuts 1, 2, and 3, raises were completed to a height of 32 ft., or the elevation of the first sublevel. They were then connected by east and west crosscuts to the main foot-wall raises 30, 40, 50, and 60, shown in Fig. 4. The crosscuts in raises 1 to 5 were then driven west and the

Jan 1, 1923

By E. S. Wheeler

The conversion plant of the Clirnax Molybdenum Co. is at Langeloth, Washington . County, Pennsylvania, approximately 30 miles west of Pittsburgh. The molybdenite concentrates converted originate in the company's mine and mill at Climax, Co1orado.l They are delivered to the Langeloth plant by rail packed in 175-lb. bags. War production of concentrates at the mill started in 1918 but it was not until about 1920 that any peacetime uses of the metal began to develop. Early conversion of Climax concentrates was mainly into ferromolybden um, produced for the company by a custom smelter. Chronology of Plant Development In 1924 a small hand-rabbled roaster was built at Langeloth, the roasted concentrates being used principally in the production of calcium molybdate by a conventional wet method. The size of the original plant is indicated by the fact that during 1925 about 400,000 lb. of molybdenum was converted. In 1925-1926, a multiple-hearth roaster was erected (12-ft. 0.d. 8-hearth Nichols-Herreshoff); also the first experimental ferromolybdenum was produced at Langeloth. At this time sa.1cium molybdate was produced in the furnace by a process to be described. With continued interest in and increased use of molybdenum, it was necessary to arrange for enlargement of plant facilities. Although only one 12-hearth 16-ft. 0.d. roaster was erected at this time (1929), plans were prepared for a duplicate unit, which was completed in 193 5, giving a potential roasting capacity of some 16,000 lb. Mo per day under the then prevailing roasting practice. Shortly after this second unit had gone into production, increased demand overtaxed the plant, and as a result two 12-hearth 18-ft. 0.d. roasters were placed in operation in 1936 and 1937. This gave the plant a potential roasting capacity of 40,000 to 50,000 lb. Mo per day, and necessitated major changes in auxiliary handling equipment as well as improved facilities for producing ferromolybdenum. Following the introduction (1938) of a new product—molybdic oxide briquets— and because of the constantly growing demand for molybdenum, plant facilities were again enlarged in 1940 and 1941 by the erection of two 16-hearth 18-ft. 0.d. roasters. These two new units, along with a change in roasting practice, brought the potential roasting capacity to 150,ooo to 190,000 Ib. Mo per day, based on about 15 lb. per sq. ft. of hearth area. Other departments of the plant have necessarily grown, until today the plant is modern throughout and completely mechanized, with equipment geared to produce marketable products as follows:

Jan 1, 1944

IN A broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SiO2, MnO, and other oxides charged as such, and (3) lime charged or fed to the heat to neutralize the “acidic”: oxides present (Si02 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, we have only a somewhat. imperfect control over these factors, so that beginning at about the lime-boil period in the heat, and later in the early refining period, it becomes necessary for the first helper, as the heat progresses, to make quick estimates of the composition and physical state of development of the slag (as well as of the amounts of phosphorus, sulphur, and carbon in the metal) from which he can judge how much extra lime, roll scale, fluorspar, and other additions will be needed not only to give the desired final slag composition, but also to hasten the complete fusion or shaping to a desired viscosity in the liquid state. The discussion in this chapter is limited essentially to those more or less practical rapid methods of slag estimation that have been used, or at least tried, for these purposes under actual open-hearth shop conditions. Another aspect of importance here is the extent to which the freedom of choice to the operator is limited by available charge materials, product specifications, and the oxidation and other chemical- reaction effects which inevitably occur under the conditions of this furnace process. For a better understanding of these control limitations and of the chemical and physical background of the subject, the reader is urged to read at least part of the discussion in Chapters XVII and XIX. Charge materials are discussed in Chapter IV, and many of the details of charging, melting, and refining practice closely related to slag control are given in Chapters VI and VII.

Jan 1, 1944

By F. D. Weeks

The Salida smelting plant, owned by the Ohio & Colorado Smelting & Refining Co., is situated at an altitude of 7,000 ft., about 2 miles west of Salida, Colo., and 215 miles southwest of Denver. Salida is a division point on the Denver & Rio Grande R. R. where the narrow-gage line serving the San Juan region joins the through standard gage. This narrow-gage road also serves the coal and coke companies at Crested Butte and the lime quarries and mines at Monarch and Garfield, which are only 20 miles distant. These facts, together with the possibility of an appropriate site, doubtless influenced the builders to locate at this point. The smelting plant and yard occupy 80 acres of land on the northeast side of the Arkansas River. The slope of the ground is such as to permit of the ore being delivered by cars at a point 25 ft. above the feed floor; and in front of the furnaces there is a fall of 50 ft. for the slag dump. A recent purchase of river bottom has provided slag room for 20 years. As originally constructed, the plant consisted of four blast furnaces, 40 by 144 in. at tuyéres, two copper-matting furnaces, dust chamber, stack, power plant, blowers, sampling works, and one railroad trestle about 16 ft. from bed floor to rails. Later 12 hand roasters of excellent design were added and the practice of smelting leady matte in a copper-matting furnace was abandoned. Since the plant passed under the present management the equipment has been increased so that the following is a brief description of the same at this date: Two lead blast furnaces, 48 by 180 in. at tuyéres, 17 ft. 6 in. tuyéres to feed floor; four lead blast furnaces, 40 by 144 in. at tuyéres, 17 ft. 6 in. tuyéree to feed floor; two copper-matting furnaces, not used; blast-furnace flue, 900 ft.; area 245 sq. ft.; blast-furnace stack, 150 ft.; above furnace floor, 190 ft. When smelting a 500-ton charge per day, the gases approximate 63,700 cu. ft. per minute and travel at a speed of 260 ft. per minute. The slag is hauled by a 10-ton electric locomotive; the slag shells and settler refuse are elevated to a bin on the feed floor by an electric hoist. The matte is tapped in 1,600-lb. cakes and loaded into cars

Jan 1, 1916

By D. D. Button, L. D. Jaffee

INTEREST in the use of graphite as a high-temperature engineering structural material has recently increased markedly. However, actual use of this material has been limited, in part because information about its high-temperature mechanical properties has been lacking. The information needed includes not only reliable values for the properties, but also how to control these properties. Malmstrom, Keen, and Greenl have reported on the tensile and creep properties of some graphites above 2700° F (1500°C). They observed measurable creep under tensile loading at 4000 OF (2200 °C) and higher, with elongations of about 7 pct at 4500°F. Their typical elongation-vs-time curve showed the normal three stages of creep found for many metals at elevated temperatures. The specimens used were heated by passing an electric current through them. This method of heating caused a significant difference between the surface and axis temperatures, and may have affected the results. More recent work by kattus, in which the specfinens were also heated by their own resistance, showed very little plastic deformation for either slow or fast tensile testing or for creep testing. Work at this Laboratory, already reported,3 showed that for temperatures above 4500 "F and under conditions of slow tensile loading some commercial graphites exhibited elongations up to 20 pct. The work reported here is the continuation of a study of the tensile creep behavior of some commercially available synthetic graphites at temperatures up to 5300°F, and is preliminary to a more systematic investigation of the variables governing the high-temperature mechanical properties of graphite. MATERIALS TESTED The tests were conducted on six blocks from four lots of synthetic graphite bearing four different commercial-grade designations. These blocks were selected because their tensile stress—strain properties had been determined in previous work.3 Table I pre- sents the available information, supplied by the producers, on the processing of these materials. Also included in this Table are the densities and the tensile strengths at room temperature and 4500°F determined by the authors. EXPERIMENTAL TECHNIQUE The furnace used to heat the specimens for testing is shown in Fig. 1. The heating element was a graphite tube, 3-in. OD by 2 1/2 in. ID by 24 in. length. A spiral was cut into the 6-in. center portion of this tube to provide a high-resistance sec-

Jan 1, 1961

By John Campbell

An approximate theoretical model is proposed to quantitatively predict freezing ranges Tf and hydrostatic tensions P developed within solidifying binary alloys, allowing for a certain amount of diffusion of solute in the solid during solidification. The maxima in ATf and AP as functions of composition are shorn to occur at smaller solute concentrations than would be expected from the equilibrium diagram, and are found to correspond closely to experimentally observed maxima in microporosity. THE freezing range of simple binary alloys appears to have been little studied, except for certain indirect observations on the defects, particularly microporosity and hot tearing, arising in long freezing range materials. Two theories relating to the freezing range of alloys and its effect upon porosity are reasonably well established, and appear to have been held in isolation from each other: a) From purely equilibrium considerations early researchers expected that an increase in solute content of an alloy should increase the freezing range (defined here as the equilibrium freezing range ?Tf = Tl-Ts where TL and Ts are the liquidus and solidus temperatures, respectively) and thereby increase the width of the pasty zone for a given set of conditions. This in turn should increase the difficulty of feeding the residual liquid through the dendrite mesh to compensate for the contraction on solidification, and consequently tend to increase the observed amount of porosity. From qualitative observations on steels Czikel1 reports an increase in porosity with increasing carbon content up to 0.46 pct C. More careful measurements by Whittenberger and Rhines2 on fourteen different alloy systems showed an approximately linear relation between ?Tf and pct porosity (although unfortunately the precise experimental data is not given). b) Conversely however, other authors3"5 propose that porosity is reduced by the presence of increased amounts of eutectic present at the final solidification temperature. Lees7 and Bochvar6 claim that the hot tearing of alloys is similarly reduced. Scheuer8 has put forward a theory to explain this effect, Fig. 1. The argument is basically that solidification progresses on a plane front through a relatively open dendrite network and is thus (the argument is not developed more explicitly) easier to feed. One would expect effect a) to operate at low solute contents, and b) to be important at higher solute contents, so that at some critical composition a max-

Jan 1, 1970

By Jay Carpenter

THIS paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator. This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with aTrent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. .These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and. delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 8, 1915

By L. Zwell, H. A. Wriedt

In describing their procedure for measuring the lattice parameters of solid solutions, Abrahamson and Lopata report (p. 77) the final heat treatment of their alloy specimens as "700°C for 100 hr, followed by a furnace cool". The isothermal part of this treatment may be expected to precipitate solute in excess of the stable a solid-solution limit at 700°C; the subsequent slow cooling is likely to reduce the dissolved solute still further. Fig. 1 (upper) presents the data for titanium alloys so he;rt-treated and shows the lattice parameters of solid solutions containing up to 3.5 at. pct Ti; Fig. 17 (lower) shows 2 at. pct Ti as the solubility limit in a iron at 700°C. Figs. 1 and 17 are thus incompatible. The paper contains comparable incon~patibilities for zirconium alloys, for niobium alloys, and for tantalum alloys. The final heat treatment at 700°C may also be responsible for the anomalous "knee" in the lattice-parameter data for nickel alloys, Fig. 3. The "knee" composition is located near the 700°C limit of the stable a solid-solution field;37 alloys of the experimental composition range with more nickel than the "knee" composition are two-phase at 700 C and prolonged heat treatment of them at 700°C would tend to produce inhomogeneity rather than homogeneity. In Figs. 4 and 7, the composition ranges of the zirconium, hafnium, and niobium alloys examined terminate at alloy concentrations of 0.1 to 0.2 at. pct. These metals form very stable oxides and their partial removal from solid solution in iron by impurity oxygen may be expected. We believe that the authors should have reported the procedure by which they distinguished the amounts of alloying elements in solution and in oxide. The diagrams pertaining to copper in Figs. 3 and 18 (lower) are almost certainly incorrect. Three recent investigations of this system38-40 all substantially agree on the solubility of copper in a iron, finding it to be much larger than that reported by Abrahamson and Lopata. The change of the lattice parameter with composition reported by Abrahamson and Lopata is too large by a factor of three to five, as seen by comparison with the findings of other investigators.41738 Moreover, the authors violate, in Fig. 18, the accepted Fe-Cu constitution diagram37 by ignoring the eutectoid at about 850°C.

Jan 1, 1967

By P. W. Ramsey, G. L. Werley

THERE have been numerous examples in recent years of the similarity between aging behavior and diffusion behavior, where a plot of the logarithm of the aging rate versus the reciprocal of the absolute temperature yields an approximate straight line, analogous to a similar plot of the diffusion coefficient D (log D vs. 1/T). Austin and Rickettl have pointed out that this linear relationship holds empirically for the de- composition of austenite into pearlite and bainite in carbon steels, and Robertson' has shown similar trends in the aging of 24S-type aluminum alloys. Jenkins and Bucknall³ have also demonstrated the association between aging and diffusion rates for nickel-silicon-copper alloys. Jetter and Mehl,4 however, have shown that the maximum rate of dilation of a series of aluminum-silicon alloys does not show this linear relation and Mehl5 has pointed out that careful study of available knowledge indicates that "aging rates increase with temperature approximately exponentially, whereas D increases precisely exponentially." He further notes that "the rate of aging at a given temperature is the greater the lower the melting point of the alloy, which is also true for D." This paper describes the aging changes occurring in a zinc-25 pct manganese-15 pct copper-0.1 pct aluminum die casting alloy. It was found that this alloy does show this linear relationship and use was made of this relationship to estimate aging rates at low temperatures from data acquired at elevated temperatures. It should be noted that the aging reaction is being studied only indirectly, using changes in certain properties as criteria of the progress of the phenomenon. This alloy is purely an experimental one and is not available commercially. Zinc-Manganese-Copper System: The zinc-rich portion of the zinc-manganese-copper diagram which is of significance in the present work is quite uncertain. X ray examination of the alloy as die cast shows a phase similar to the epsilon phase (hexagonal close packed) of the copper-zinc system. All of the data accumulated indicate that the epsilon phase of the zinc-manganese-copper alloy is stable at high temperatures; that is, 500°C or above. Below this temperature a new phase is precipitated on annealing, and a decrease in specific volume occurs. At elevated temperatures this phase change occurs quite rapidly, while at room temperature the alloy has shown no change after several years. According to X ray data, this precipitated phase resembles the gamma phase (cubic) of the copper-zinc system, a hard and brittle structure. From examination of the microstructure and from X ray examination of the alloys annealed at

Jan 1, 1951

By C. L. Baker

The district of Catoree, San Luis Potosi, ranks among the first half-dozen silver-producing camps of Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapnni, Mazapil, Palomas, Musquiz, Minas Viejas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (610 m.) in 41/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catoree from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catoree, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to crosivc forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstone?, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains: some of this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution of the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebblcs, and finer detritus. According to tradition, the higher portions of the Sierra Catoree were forested with pines and cedars but none remain within the mining district, although cedar is found farther south in the range. The vegeta-

Jan 1, 1922

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By Martin Epner, Eric Gregory

DURING the past decade, considerable work has been carried out on various cermet systems in an effort to produce materials suitable for high-temperature applications in gas turbines. Most of the materials have not, as yet, met the requirements of the engine manufacturers, primarily because of their lack of room-temperature ductility and thermal shock resistance. In the field of tool materials, however, although ductility is still of prime importance, much has been accomplished by improving design parameters and the quality of carbide materials with a view to using cermet compositions successfully. The systems described in this paper were designed primarily for application in this field, although their development was a natural outcome of work on similar compositions designed for high-temperature service. In steel-bonded titanium carbide, the steel binder imparts heat treatability to the system while the carbide provides abrasion and wear resistance. Combining the carbide and the steel matrix in carefully controlled proportions results in a composite material which, when the steel is hardened, has man of the properties of cemented tungsten carbide. In the annealed condition, this material can be readily machined by the conventional chip-removal techniques. Titanium carbide has certain distinct advantages over many of the other carbides when combined with a steel matrix. It is among the hardest of the carbides and is one of the most stable. Liquid iron wets titanium carbide, and this wetting assists in the formation of a dense cermet. Once the composite structure has been formed, the titanium carbide acts as a relatively inert phase during the heat treatment of the matrix. PREPARATION OF ALLOYS The steel-bonded titanium-carbide materials described in this paper were prepared by the liquid-phase sintering technique. The titanium carbide used had an average particle size of 6 to 7 p, a total carbon content of 19.4 pct and 0.35 pct free carbon. This was blended with the elemental metal powders by ball milling them together in a hexane medium. After drying, paraffin wax was added to the blend to provide green strength in the pressed briquettes, and compacting was performed at 15 tsi. Liquid-phase sintering was carried out in vacuum at temperatures which depended on the chemical composition of the system involved, but which were usually around 2640° F. The resultant materials had a density approaching 100 pct of theoretical. The

Jan 1, 1961

By M. B. Ramachandra Rao

THE spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° I7' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1-the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous micachlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, lithomargic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. METHOD OF SURVEY AND APPARATUS EMPLOYED The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1944

By Howard V. Sears

ArcHodrilling (Arcuate Hole Drilling) of short radius overhead curved holes from within the working level with a new, small-diameter in-the-hole drill produces tangible, assayable chip samples from the entire height of the projected mine level where the hole arcs down immediately in front of the working face. Drilling through the projected level with diamond coring tools produces samples showing the competence of roof and floor strata as well as the geological and economic characteristics of the ore. Hand-portable solid state electronic surveying instrument has been developed to survey the ArcHole and a convenient nomograph plotting record sheet converts survey digital readouts to hole inclination in degrees, to radius of curvature in feet, and to attitude of the plane of curvature from vertical in degrees, all without calculation. The ArcHodrilling system offers a tool with which the exploration geologist can more nearly assess the true potential of old mining properties being reexamined and to reduce the number of surface diamond drill holes needed to secure development data about new ore bodies. It gives the mine geologist an opportunity to secure those data at a fraction of the cost of drilling from the surface. The mining supervisor has a convenient, cheap tool to look ahead to know what he will be mining tomorrow. The mill supervisor has an opportunity to reduce his mineral loss in tailings by being able to anticipate the grade of his mill feed.

Jan 1, 1973

The world's production of petroleum in 1926 amounted to nearly 150 million long tons, of which India contributed 0.72 per cent. In 1927, this figure jumped to some 172 million long tons, of which the Indian proportion, on a practically stationary production, fell to 0.64 per cent. In 1928, there was another substantial rise in the world's production, which reached the figure of over 181 million tons. In 1929, there was another jump to over 202 million tons, but in 1930 the world's production fell to about 193% million tons, in 1931 to about 187 million tons, and in 1932 to about 183 million tons, while in 1933 the production rose again to about 202 million tons, in 1934 to about 215 million tons, and in 1935 to 233 million tons1. Decreases were shown by Poland, Sarawak, Egypt, Rumania and France. All other important producers showed an increase in production, by far the largest being due to Iraq, as a result of the opening of the pipe line to the Mediterranean. The United States contributed 60.9 per cent of the world's supply in 1935, Russia 10.7 per cent, Venezuela 9.4 per cent, Rumania 3.9 per cent and Iran 3.1 per cent. In 1928, India contributed 0.64 per cent, which fell to 0.60 per cent in 1929 and rose to 0.62 per cent in 1930, 0.63 per cent in 1931, and 0.64 per cent in 1932, and fell again to 0.62 per cent in 1933, to 0.60 per cent in 1934 and to 0.50 per cent in 1935; her position on the list of petroleum-producing countries fell from eleventh in 1929 to twelfth in 1930 to 1933, her place being taken by Trinidad and to thirteenth in 1934 and 1935, owing to the production by Iraq. The production of petroleum in India (including Burma2) increased slightly from 322,025,280 gal.3 in 1934 to 322,662,336 gal. in 1935, the highest figure in the history of the industry. The increase in 1935 is due to an increase of some 4 million gallons in Assam, almost offset by a decrease of 31/2 million gallons in Burma. This increase in output in 1935 was accompanied by an increase in estimated value amounting to Rs. 22,73,550 (£170,944).

Jan 1, 1937

By J. J. Bodmer

The substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pitsand—siliceous sand, as it commonly occurs mixed with gravel—and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order. to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (unslaked) lime with sulphate of lime, or plaster of Paris. The graystone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By ALEXANDER S. CORSUN

THE main orebody in the Hecla mine, Burke, Ida- ho, occurs along a nearly vertical shear zone in the Burke quartzite, with a substantial gouge and lamprophyre dike occurring in an irregular manner throughout the lode. The veins range from 3 to 40 ft. wide and dip from 70 deg. to 90 deg. There is 110 definite line of demarcation between the lode and the wall rock. Stringers of ore are often found in the wall rock for irregular distances. Horizontal but irregular quartz stringers are also found running into the walls and positions of the wall have a tendency to break to the quartz stringers and the accompanying gouge, which causes indefinite, uneven and extremely heavy side and top pressures.

Jan 1, 1930

By W. Mont Ferry

It is impossible to speak in exact terms of the effect that selective flotation has had, is having, and may have on the State of Utah. Its results enter into the economic structure of the state in so many ways and its ramifications are so widespread, that every line of industry is affectcd. Some effects can be definitely determined; others can be reasonably approximated; but the effect as a whole can not be set out in exact figures. Utah is essentially a mining state; mining is its basic industry and always will be. Agriculture, equally a basic industry, and of course, equally vital, can be practiced on only 6 per cent. of the 85,000 square miles of its area. It follows, therefore, that the economic future of this state depends upon a development of its natural resources. About 6 or 7 years ago, the mining industry in Utah was at a low ebb. This condition was caused partly by postwar conditions and other temporary causes, but prevailed also, which was most important, because the direet-smelting ores of the state were being rapidly exhausted and the cost of treatment of complex ores was almost prohibitive. Furthermore, the wet concentration of low-grade ores was unsatisfactory and did not result in producing a good smelting product. On visualizing this situation, one of the large smelting companies in the valley had the courage, ability and faith to develop and expand the principles involved in selective flotation of complex ores. This example has been followrd by other smelting and reduction companirs and the result has changed the entire aspect of the mining industry in Utah. The utilization of the zinc in the low-grade, lead-zinc-silvrr ores was the principal prob1t.m to be solvcd. The average yearly production from the State of Utah for the 10 years beginning 1914 and ending 1923, was something less than 10,000 tons of zinc corlcentrates. This period includes the world war, when abnormal priccs stimulated production. In 1924, selective flotation began to be practiced on a considerable scale, replacing concentration by gravity and bulk flotation which had been used generally until this time. Production and Value of Zinc Concentrates The production of zinc concentrates during 1924 was approximately 24,000 tons, or twice the average yearly production of the previous 10

Jan 1, 1928

By A. Lee Barrett

THE Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting as a part of this report the second of a series of maintenance cost comparisons. The committee's purpose is to assemble maintenance costs on all equipment connected with mechanical operations at the face of coal mining and to arrange these costs by districts so that comparisons can be made between districts and within districts. The committee, this year, sent 35 questionnaires to representative coal companies who either reported last year or had advised specifically of the inability to report to last year's questionnaire primarily because of limited time. The response to the questionnaire this year was not as good as last year, only 20 of the 35 selected companies returning a completed questionnaire. This year's data has been .compiled and combined with last year's data to present a comparison of the 1945 and 1946 costs of loading machines, shortwall cutting machines, universal cutting machines, service locomotives, shuttle cars, and mine cars. The same tabulation by districts is used as was used for 1945. As was indicated by last year's report there is considerable variation in the maintenance cost of mining machinery in the various coal mining districts and due to this high variability it was not felt practical to attempt to Arrive at weighted averages. Consequently, all average figures used in this report are straight averages. An analysis was made of companies reporting both this year and last year in an attempt to determine the trend in maintenance costs for different classes of equipment. Ten representative companies are used in this computation. Table I shows the average cost for 1945 and 1946. It is felt that the negative trend in the maintenance cost of universal cutting machines probably represents the effect of the purchase of a relatively large number o new machines in 1946 with little maintenance cost appearing during the first yeas of operation. The grand total figure indicates an upward trend amounting to plus 18.7 pct. However, this figure is viewer with some suspicion because of the effect of the universal cutters decreasing maintenance cost and it is concluded that direct application of percentage increase should be made to types of equipment. In Table 2 covering maintenance costs of various types of mining equipment for 1945 and 1946 the results, obtained in Table I indicating trends were applied to those

Jan 1, 1948