Search Documents

By C. Schlumberger, M. Schlumberger

The object of this paper is to clarify the idea, so important when exploring by potential methods, of the depth of investigation attainable by electrical measurements. After defining, with some precision, .the term "depth of investigation'' in geophysics, the authors show how it is possible to regulate this depth in potential methods and to obtain an 'electrical drilling" from surface observations. They consider also the difficulties encountered in deep measurements and indicate how it is possible to reach greater depths than those having an industrial interest. Depth of Investigation The term, depth of investigation, in its general sense, is easily understood. For instance, a driller who can pull cores from a depth of 2000 m. is capable of working, with accuracy, to that depth. By means of a properly placed drill, he may locate an orebody at a depth of 1999 m., however small this orebody may be. On the contrary, the term as used in geophysics requires precise elaboration. As a matter of fact, no geophysical method, irrespective of the physical property studied (density, magnetic permeability, conductivity), can discover a very small body at a great depth because, in practice, the physical parameter upon which such a geophysical method is based is never regular enough, throughout the ground, to distinguish the feeble anomaly caused by the small, deep-lying body from the numerous anomalies due to irregularities of the encasing terrains. Aside from this question of the ratio between the size of the body being hunted for and its depth of burial, a second factor plays its role in the possible depth of investigation; that is the difference, for the parameter under consideration, between the body and its surrounding material. The greater this difference, and the more homogeneous the encasing terrains, the greater is the possible depth of investigation. This being generally established for all geophysical methods, it is possible to distinguish two main classes of these methods, from this same point of view

Jan 1, 1932

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By T. S. Hutchinson, C. E. Kemp

The bottom water drive analysis presented by Muskat has been extended to include fields with wider well spacings. Curves are presented from which volumetric sweepout, water-oil ratio, and rate relations may be calculated. The effects of non-unity ratios on sweepout eficiency and productivity decline have been studied by an approximate method. Also, the effect of gravity on volumetric sweepout has been approximated for a particurlar geometry. INTRODUCTION The purpose of this paper is to report work done in applying the analysis of bottom water drive reservoirs given by Muskat1 to a larger class of reservoirs, to extend this analysis to include the effects of gravity and non-unity mobility ratios in an approximate manner, and to investigate the rate of decline of productive capacity. The bottom water drive type reservoir is one where the oil is underlain by a water zone of sufficient thickness that water movement is essentially vertical. This system is defined in more detail in the appendix and a one well element is shown diagrammatically in Fig. 1. Muskat obtained solutions to the equations describing the volumetric displacement efficiency of idealized bottom water drive systems by assuming that gravity effects due to differences in density betwecn oil and water were negligible and that the mobilities of oil and water were the same. If either of these assumptions is not made, the complexity of the system makes an analytical solution well nigh impossible at the present stage of mathematical development. Coles and Stade' developed an approximation to consider these factors. The authors have refined approximations, starting with the same basic assumption, which should give a somewhat quantitative picture of bottom water drive performance when mobilities are not equal and the effects of gravity are not negligible. The results of these approximate calculations can then be used to obtain the decline in well productivity as the field is depleted.

Jan 1, 1957

By M. A. Mahtab, T. M. Yegulalp

This paper presents the development and application of an approach for clustering fracture orientation data. Data are projected on the surface of the unit upper hemisphere and the clustering approach is applied in three steps: (1) randomness test and identification of dense clusters, (2) estimation of cluster statistics, using Bingham distribution, and (3) rejection of extremal data based on Chauvenet's criterion.

Jan 1, 1982

By George A. Roberts, Robert F. Mehl

WHEN austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.1 This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced,4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ae1.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. EFFECT OF INHOMOGENEITIES ON REACTIONS NEAR Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously;1,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional quantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a "fine-grained steel." These steels can be compared at the same grain size by heating C to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By Milnor Roberts

CORNWALL, a Mecca for metal miners the world over, is easily reached from the southern coast of England. Passengers who land at Plymouth or Southampton can connect with a fast train from London called the "Riviera express," which traverses the beautiful counties bordering the English Channel. In Cornwall the traveler soon notices the pits and stock-piles of white china clay, and the metal mines, both placer and hard rock. The deposits are associated with granite batholiths, of which there are four principal ones, each a few miles in diameter. Tin mines are especially worked in the granite near its borders and also in the immediately surrounding Paleozoic slates. Copper and lead are no longer of importance here but tin is being produced steadily from several mines, with arsenic and tungsten as by-products. At the close of the war the man-power available. for these mines had been reduced to one-third of normal, and only now is it again reaching full strength. As mining in Cornwall antedates the Christian era, even a Nevada prospector would have to admit that "she's a permanent camp." SUB-TROPICAL CORNWALL Redruth and Camborne are industrial centers of the tin mining industry, but more tourist hotels are found in neighboring resorts such as St. Ives, a quaint fish-ing town on the Atlantic-side of the peninsula of Corn-wall, where the numerous cats descended from those mentioned in the ancient riddle-rhyme about St. Ives now occupy every doorstep and wall. Another charm-ing resort. Penzance on the shore of the English Channel, is known by name to the public through the opera "The Pirates of Penzance," but is of especial in-terest to students of nature for its palm trees and other subtropical plants, which thrive owing to the nearness of the gulf stream, although the latitude is that of northern Newfoundland, Winnipeg, and the northern end of Vancouver Island. Among the industrial plants at Camborne are those of Holman Brothers, Ltd., where drills and other forms of mining equipment are manufactured. At the Corn-wall School of Mines, which specializes on the district, the staff has assembled excellent collections of local ores, which repay study by a visitor.

Jan 1, 1928

By Ionel I. Gardescu

In connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,' an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the displacement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S6, R4, the sand reservoir R, R1, R², F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415Ib. per sq. in. with no free gas present. This was ascertained by closing off all the outlet valves and determining the coefficient of compressibility of the system by means of the displacement chamber D. Much difficulty was encountered in eliminating all of the free gas masses from the oil reservoir. The dead oil originally present in the

Jan 1, 1932

By R. R. Webster, H. T. Clark

The side-blown converter has been investigated as a possible commercial process for the production of low nitrogen steel. During this work, two converters of 3-ton and 22-ton capacity were operated on a pilot plant basis for a total of 214 heats. The steel made in these converters was low in nitrogen and possessed good cold working properties. Some problems of converter operation remain to be solved. IN plants operating with a high iron capacity, sev-eral different refining methods are used in the conversion of the molten pig iron to steel. These include various ore practices in stationary and tilting open-hearths, the duplex process employing the Bessemer converter and open-hearth, and the Bessemer process. At J&L, a considerable part of the iron produced is handled by the Bessemer process, either alone or in conjunction with duplexing, and therefore an appreciable portion of the steelmaking research effort has centered about the method. This paper covers research work on the development of the side-blow converter for the commercial production of low nitrogen ingots and includes descriptions of the operation of a 3-ton and a 22-ton experimental converter at the Aliquippa Works. The refining of iron to produce steel requires the removal of a large portion of the carbon and silicon and the control of manganese, phosphorus and sulphur which are present in the iron in varying amounts. The first large-scale means of refining iron was the acid Bessemer process which was brought into use almost 100 yr ago. This method, using compressed air as the refining medium, accomplishes substantially complete removal of carbon, manganese and silicon. Phosphorus and sulphur are not affected but, by choice of an iron composition sufficiently low in these elements, a commercial product can be produced. Since the process will handle large tonnages rapidly, operates without external fuel and with a minimum of additional equipment, it quickly became the major tool in the early expansion of the steel industry. Later, the basic open-hearth process, by affording control of phosphorus and sulphur and by consuming the large quantities of steel scrap that were becoming available, forced the acid Bessemer process into a secondary position in the industry. During the past two decades the demand for steel to be used in cold forming and drawing operations has gradually increased. Bessemer steel, because of its work hardening and aging characteristics, is not as suitable for these applications as basic open-hearth steel, consequently the decline of the process was accelerated. More recently, because of changing economic conditions, this long range trend appears to have been arrested or perhaps reversed. Ingot production data for recent years furnishes only an incomplete picture of the importance of the converter in the American steel industry; open-hearth furnaces utilize large tonnages of blown metal for which no published statistics are available. Metallurgical Aspects The fundamental difference between Bessemer and open-hearth steels apparently lies not in the method of manufacture but, rather, in the differences in chemical composition of the two steels. It is further believed that the principal features distinguishing Bessemer from open-hearth steel are the higher nitrogen and phosphorus contents of the former. Evidence supporting this position is supplied by tests on laboratory induction furnace heats that were made to contain varying amounts of phosphorus and nitrogen but were otherwise similar to normal low carbon silicon-killed steels. Fig. 1, 2 and 3, summarizing the test results, are taken from G. H. Enzian's paper titled, "Some Effects of Phosphorus and Nitrogen on the Properties of Low Carbon Steels."' Fig. l indicates that phosphorus has a marked effect on the cold work embrittlement of steel as shown by the work brittleness test of Graham and Work.' In the low nitrogen steels, which as a group have the better cold working properties, the effect of phosphorus variations is the more pronounced.

Jan 1, 1951

By R. W. Hyde, S. E. Eaton, B. S. Old

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

By R. W. Hyde, B. S. Old, S. E. Eaton

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By NEWTON B. KNOX

PERU, lying south of Ecuador and having common frontiers with Brazil, Chile, and Bolivia, includes over a thousand miles of the Andean mountains. The coastal plain is arid and narrow and the Amazonian jungle region is of interest only on account of its oil and gold placer possibilities. The mountain zone, however, here forms one of the world's most highly mineralized regions. The Peruvian Andes, like their Bolivian and Ecuadorian counterparts, form two distinct chains separated by the great Apurimac and Maralion valleys; but these rivers cut through the Eastern range to join the Amazon drainage, and the central valley is missing north of the passes thus formed by these rivers; the localities where the ranges are joined are aptly called knots. In addition, in central Peru, there exists a third range lying to the east of the first two and separated from them by the Urubamba and Huallaga Rivers. The Eastern range, however, is of little importance to the miner for few metal deposits are to be found therein except for the gold mineralization in the South. In general, deposition of metals in the Peruvian Andes accompanied igneous intrusions which invaded the folded Paleozoic and Mesozoic rocks during the Tertiary; thus the ore bodies are all typical of shallow or moderate depths.

Jan 1, 1945

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnXTe have been grown from The melt under liquid B2O3 using the Czochralski technique. The PbTe-SnTe crystals were grown from near-stoichiometric melts and from melts with slight deviations from sloichiometry. Crystal growth rates ranging from 1 mm per hr to 1 cm per hr were employed, the latter being generally used. Several investigations were performed to characterize the single crystals grown In this study. The phase diagram of the PbTe-SnTe system was examined. X-ray analyses verified the single-crystal character of the crystals, and powder pattern lattice parameter determinations showed that Vegard's law was followed within the limits of the experimental error. The as-grown crystals were p-type with apparent carrier concentrations of -8 x 1018 to -8 x 1020 carriers per cu cm. Hall coefficients, resistivities, and carrier mobilities were determined as a function of composition. Dislocations were revealed by an electrolytic etch, and the crystals were found typically to contain 2 to 4 x 105 dislocations per sq cm. Microhardness measurements were performed; no maximum in the Vickers hardness us composition curve was seen. Mass spectrometry was used for impurity analyses, and the crystals were found to contain 1 to 2 x 1017 total p-type impurities per cubic centimeter. Distribution coefficients were calculated for the major impurities which were Na, Mg, Al, Si, Cl, and Zn. RECENTLY interest has been stimulated in the preparation and characterization of many alloys of the binary compound semiconductors. This interest is due primarily to the almost unlimited possibilities of adjusting the semiconducting characteristics of these materials by varying the alloy compositions. One alloy system which has been receiving extensive investigation is the PbTe-SnTe system, since these alloys show promise of being useful as emitters and detectors of electromagnetic radiation in the spectral range of 8 to 14 µ. This paper reports on the growth of PbTe-SnTe single crystals by the Czochralski technique and investigations of the general properties of these crystals. The phase diagram of the PbTe-SnTe system was investigated so that specific alloy compositions could be attained. I) CRYSTAL GROWTH The PbTe-SnTe single crystals were pulled from the melt using the Czochralski technique. Generally, the crystals were grown from near-stoichiometric melts, although special growth runs were made from both lead-rich and tellurium-rich melts. Growth of single crystals from up to 5 pct lead-rich melts presented no problems; however, melts with tellurium in excess of -1 pct caused volatilization problems which generally made crystal growth impossible. All melts were prepared from high-purity materials as follows: 1) lead— 6 N— Cominco (Cominco Products, Inc., Spokane, Wash.); 2) tin—5N—Cominco; and 3) tellurium— 5N+— American Smelting & Refining Co., Plainfield, N.J. No further purification of materials was undertaken in this study. The elements were reacted at -1000°C in a vacuum-sealed silica tube for a few hours, a gentle rocking action being used to ensure thorough reaction. The cast ingots were then transferred to a silica crucible for crystal growth. A schematic diagram of the growth apparatus is shown in Fig. 1. The Vycor tube is sealed at both ends by O-ring flanges so that a vacuum or a positive pressure may be maintained in the growth chamber. The pull rod and crucible may be rotated; all crystals produced in this study were grown with the crucible sta-

Jan 1, 1969

By Floyd Kelley

THERE is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the .high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensation of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is, little gained by using specially purified gas, because it becomes contaminated after reaching the furnace.

Jan 1, 1931

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series,1 for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship [p] to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distribution line is w = Cxm [I] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983

By Eugene McAuliffe

The mining press, as well as certain federal and state bulletins, refer from time to time to the relative hazards that attach to loading bituminous coal by hand when compared with the so-called "mechanical loading" process. Much of the coal coming under the head of hand-loaded coal is won in part by the use of machinery; the coal-cutting machine is in general use, the electric power drill employed to a lesser extent. Therefore it may be said that the principal difference in the process employed, mechanical loading versus hand loading, lies in the fact that some type of loading machine is employed in the mechanical loading process to lift the coal from the face of the room, place or entry, after it is mined, placing it in the pit cars for transport to the tipple. It is a common practice to compute accident records on the basis of tons mined per fatal and per nonfatal accident, disregarding the fact that it is possible to produce by the aid of coal-loading machines the same daily, monthly and annual tonnage with a much smaller force than is required where the coal is all shoveled by hand. Inasmuch as the men who are released by the substitution of machinery for hand labor must find employment elsewhere, suffering some measure of hazard in their new occupation, we are of the opinion that the true relative hazard that attaches to the processes of mechanical loading and hand loading can be determined only by using as the basis of comparison "man shifts worked" or "hours of exposure" experienced per accident. The Union Pacific Coal-Co., beginning with the year 1929, undertook to maintain a true record of man shifts worked per compensable accident, giving equal weight to fatal and nonfatal accidents. Accidents lacking sufficient severity to come under the compensable terms of the Workmen's Compensation Act were not included in the compilation, the Act providing that "no compensation, except the expense of medical attention, shall be allowed for the first seven (7) days of disability, unless the incapacity runs beyond the period of twenty-one (21) days, in which case the compensation shall run from the time of the injury." With the further thought that all accidents suffered by employees engaged in any service, in or about the place where the loading process

Jan 1, 1931