Search Documents

By O. W. Ellis

Recently there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2 alone gave reliable information in this regard. Even today his determinations of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time—their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systernatic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington, 16 Smalley33 and Thiband 45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper. The situation in regard to these alloys in 1926 was very clearly stated by an anonymous writer,47 in The Metallurgist of February of that year, whose remarks were so to the point that they are well worth quoting: It will he seen that there are still large fields remaining to be studied in each of these systems (those of the aluminum, iron, nickel and manganese brasses) before our knowledge is adequate. When we come to the more complicated systems the position is even less satisfactory, and on account of the very incomplete nature of the work which has been

Jan 1, 1929

By J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation, sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher. The

Jan 1, 1976

By O. W. Ellis

THE question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,1 Iwasé,2 Lobley and Jepson3 stand preeminent. SOLUBILITY OF . GASES IN. COPPER Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate-possibly 30° to 60° C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1928

By Jerry G. Rose, Robert C. Howell

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14 000 kPa (2000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room and-pillar mines so that a substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction became of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal- crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 3, 1979

Photographs of Officers

Jan 1, 1923

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'" Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence.

Jan 1, 1955

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By S. E. Maddigan, B. R. Zimmerman

MOST metallurgists are well acquainted with the contributions already made to the study of metals by the use of X-rays. On the one hand, the radiographic method is constantly becoming of increasing importance as a nondestructive testing procedure, while on the other hand the techniques of X-ray diffraction have made important contributions to the fundamental knowledge in studies of phase diagrams, stress conditions, and so forth. A new, and as yet insufficiently appreciated, tool exists in the application of microradiography to alloy structures. This new procedure in many respects bears the same relation to microscopic investigations as does macroradiography to the gross inspection of metal surfaces. However, where macroradiography is used ordinarily to determine the soundness of the metal structure, this new method can be used not only to investigate micro-un- soundness but also to examine the distribution of the constituent elements within the body of the alloy. When combined with the normal procedures of microscopy, this offers a technique of great potential power. It is intended in this paper to present a few examples of copper-base alloys demonstrating the additional knowledge obtained from the microradiographic method. The detection of micro-unsoundness is demonstrated in Fig. I for a sample of cartridge brass as cast. The sample appeared quite sound when viewed under the microscope, but in reality was thickly populated with minute voids. This application of the method conforms in every way to conventional large-scale radiography and has been used to facilitate production of metal for vacuum devices.1 The true potentialities of the technique are revealed by comparison of Figs. 2a and 2b, which are respectively a- photomicrograph and a microradiograph of a cast alloy of 80 per cent Cu, 10 per cent Sn, 10 per cent Pb. The remarkable difference in appearance provides some concept of the additional information this method may yield when used as an auxiliary to microscopic studies. Fig. 2a shows two phases of the copper-tin system plus segregated lumps of lead. Fig. ab, on the other hand, shows with exceptional clarity the actual dendritic growth of the metal crystals during solidification. The practice of microradiography depends upon the laws of absorption of X-rays. This subject has been reviewed thoroughly in recent papers,1,2,3 but for clarity a brief resumé will be given here. As is well known, when a beam of X-rays is transmitted through a layer of homogeneous material, the intensity is reduced according to the relation:[ ]

Jan 1, 1944

By Frederic Dewey

IT IS common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no. real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when, arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupellation, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy1 says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 says that at a proper temperature no silver is lost by volatilization.

Jan 2, 1920

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65' to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

The following is an incomplete list of members and guests who called at Institute headquarters during the period May 10, 1919, to June 10, 1919. Victor C. Alderson, Golden, Colo. E. Fleming L'Engle, Joplin, Mo. H. Foster Bain, Washington, D. C. W. D. Mainwaring, Philadelphia, Pa. J. J. Beeson, Master Engr. Sr. Gr. W. G. Matteson, Fort Worth, Tex. Gunnar Bergstrom, Stockholm, Sweden. C. E. MacDonald, Toronto, Can. Corry T. Brown, Socorro, N. Met. Francis Nicholson, Charlotte, Va. Geo. W. Brymer, Scranton, Pa. Richard A. Parker, Denver, Colo. W. Burns, Santa Fe, N. Mex. S. B. Patteson, Jr., Allentown, Pa. H. C. Carlisle, The Pas, Manitoba, Can. G. W. Ponton, Ottawa, Canada. J. Carson Adkerson, Va. W. H. Reber, Ensign, Dallas, Tex. C. A. Cheney, Madison, Wis. T. C. Roberts, New York City. J. M. Clark, Toronto, Canada W. A. Rukeyser, Ensign, N. F. Corps. John J. Doyle, St. Louis, Mo. W. H. Staver, New York City. H. S. Emlaw, Grand Haven, Mich. D. B. Sterrett, Washington, D. C. E. Francis, Birmingham, Ala. T. V. Smirnoff, Russia. Rudolf Gahl, Denver, Colo. E. C. Templeton, New York City. Emit Gthmann, Baltimore, Md. H. A. Toblemann, Ajo, Ariz. A. B. Hardie, Philadelphia, Pa. Priestley Toulmin, Birmingham, Ala. Clarence M. Haight, Franklin, N. J. M. R. Walker, Baltimore, Md. N. V. Hansell, New York City. H. A. Wheeler, St. Louis, Mo. C. A. Heberlein, Nacosari, Mexico. D. B. Whitaker, Santiago, Cuba. Pierre Hines, Milwaukee, Wis. A. W. G. Wilson, Ottawa, Can. J. S. Hollings, Brymoba, Wales. Oba Wiser, Hanover, N. Mex C. Vey Holman, Maine. Harry J. Wolf, Denver, Colo. H. H. Howry, Denver, Colo. F. H. Wood, Mt. Vernon, N. Y. W. Spencer Hutchinson, Boston, Mass. J. P. Wood, New York, N. Y. W. B. Kunhardt, Reading, Pa. Lawrence Addicks sailed on May 17 for London; lie expects to be absent from this country for several months. Roy H. Allen has accepted a position in the research engineering department of the National Aniline & Chemical Co., Buffalo, N. Y. H. Foster Bain has gone to Shanghai, China, where he expects to remain for some time. Percy J. Bandy has accepted a position with the Cia. Minera del Mirasol S. A., at Cusihuiriachic, Chihuahua, Mexico. J. H. Batcheller is now with the North Midas Copper Co., St. Helena, Alaska.

Jan 7, 1919

By W. A. Hustrulid, N. A. Ross

An analysis of the design of medium to hard rock tunneling machines is presented. The developed equations are used to compare performances and machine requirements using kerf and fixed pick cutters to bore a given rock. With the use of pick cutters, required thrusts can be greatly reduced and still achieve the same boring rate as with present day tooth or kerf cutters. It appears that the cutting coefficient, which for most boring machines is of the order of 0.1, should be increased to one or larger to facilitate rock removal by cutting rather than grinding. The depth of cut and the indexing distance should be greatly increased to make use of inherent rock weakness.

Jan 1, 1971

By H. M. Howe

It has seemed to the writer that one important, and indeed sufficient reason, for our slow progress in learning the relation between the chemical composition and the physical properties of cast-iron, has been that the problem has not been attacked properly. It would be well to select the most probable working hypothesis which we can find, and proceed to test that hypothesis by comparison with observed facts, and by making new observations specially designed for such a test. Our first step, then, is to select the most probable working hypothesis ; and to attempt this selection, to state the hypothesis and its immediate corollaries, and to take some first steps toward testing it, is the object of the present paper. Its chief purpose is to bring the hypothesis to the attention of those who are more familiar with the evidence than the writer can pretend to be, and in a better position both to present new evidence and to discuss it. The hypothesis here selected is, that composition governs properties in the case of cast-iron, in the same general way and for the same reasons as in the case of steel, mutatis mutandis. This hypothesis, which of course makes no claim to originality, certainly seems reasonable and probable; its exposition and discussion are made easy by our existing knowledge of the constitution of normal or " carbon " steel; it therefore seems worthy of consideration.

Jan 1, 1902

By C. H. Jr. Herty

ALMOST every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gaug-ing of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanli-ness of forging steels, both carbon and alloy. In this problem the oxidiz-ing characteristics of the slag are of prime importance.

Jan 1, 1940

By Paul M. Tyler

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance.

Jan 9, 1953

Unlike the bituminous part of the coal industry, the production of anthracite has been fairly well publicized; in fact until about 1845 whenever the coal industry of Pennsylvania was mentioned in papers, magazines or books, anthracite only was meant. Beginning with shipments by river in 1820 fairly complete records of shipments were published each year, and as this variety of coal was the only one used for domestic purposes east of the mountains and north of the Potomac, there was considerable interest in the producing fields on the part of the public. Transportation of anthracite was the cause of the building of the early canals in the state, and later, of some of the earliest railroads. In most publications it has been assumed that commencement of shipments in 1820 was the beginning of the industry; this is far from being so, and it is with the earlier developments this chapter will deal, leaving the later and better known records to existing publications. (See Table No. 53.) The first reference to coal in Pennsylvania by Gabriel Thomas in 1698 has already been mentioned,1 it could only have been anthracite in that section; although of course, he never saw any coal there. Little coal was used excepting by smiths for many years after that. In 1728 the Coventry Forge paid the expenses of a man "to town for Sea Coall and Steell for ye hammer;”2 in 1729 New Castle coal was sold in Philadelphia;3 in 1740 an advertisement mentioned, "very good Pitt and Sea Coal at 18 pence a bushel; at which price 'tis allowed to be cheaper Fewel for Hearth Fireing than Wood at the present Rates,"4 a view not shared by most of the people there for about eighty years; in 1752 Newcastle coal was again mentioned.5 There are no references to coal in the writings of any of the Moravian missionaries, although some who settled near Mauch Chunk in 1746 said that the Indians there made their pipe heads of a soft black stone, which was much more apt to have been slate than anthracite." Several stream

Jan 1, 1942

By Edward O’Toole

THe Pocahontas district occupies the extreme southern end of West Virginia, principally McDowell, Mercer and Wyoming counties, and a part of Tazewell county, in southwestern Virginia. The first record of the coal field is a report by Prof. J. P. Lesley, of Pennsylvania, about 1880, in which he mentions a coal opening at the upper end of Abbs Valley, Tazewell county, Va. C. R. Boyd, a mining engineer of Wytheville, Va., published a series of articles in 1881, mentioning coal on Indian Creek, Tazewell county, and on Horse Pen creek, which coals, he stated, extended toward the Ohio River. He also mentions the Abbs Valley coal reported by Lesley. In 1881, F. J. Kimball (who became president of the Norfolk & Western R. R. in 1883)) after examining the Scott mine in Abbs Valley, went northward across Abbs Valley Mountain to the place now known as Pocahontas, where he located what has since been called No. 3 vein of Pocahontas coal. In November, 1882, Jed Hotchkiss and others prepared a cross-section of the Flat Top Mountain coal measures, some notes on which were published by Mr. Hotchkiss, between 1880 and 1892, under the title of " The Virginias.' In May, 1881, the Norfolk & Western R. R. was organized through the purchase of the Atlantic, Mississippi & Ohio R. R., an old line running from Norfolk, Va., to Bristol, Tenn., with branches from Petersburg to City Point and from Glade Springs to Saltville. At that time, charters had been granted for three railroads tributary to the New River Valley, but their proposed routes would indicate that the promoters were concerned with minerals, timber, and a connection with the Chesapeake & Ohio R. R., rather than the development of any coal in the Pocahontas district. One of them was projected to extend up Bluestone River a short distance, but not far enough to reach the coal in the Bluestone Valley, and a little grading was done for a narrow-gage road between New River Station and a point in Giles county, Virginia, near the West Virginia line. All charters and railroads in this district were acquired by the Norfolk & Western R.R.

Jan 1, 1925

By V. R. Degner

The trend in both the metallic and nonmetallic mining industry is toward processing increasingly higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This Paper reviews the R&D approach used in translating smaller flotation machine experience to the configuration of a 28.3 m3 (1000 cu ft) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1981

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924