Search Documents

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By George H. C. Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable apparatus, which can rapidly give a sufficiently reliable indication of the relative dust hazard. HISTORY OF DUST DETERMINATION IN ONTARIO The first record of mine-dust determination in Ontario is given in an article by Dr. J. H. Elliott,' in which he records a few dust counts made with the Palmer spray apparatus. There were insufficient data from which to draw any definite conclusions or reasonably compare with present-day counts using the konimeter. The first konimeter dust sampling was started in the Porcupine district in 1926, using light-field counting without adhesive and with no sample treatment before counting. A method of semidark-field counting was used from about 1928 to 1931 and dark-field illumination was adopted permanently about December 1931. The konimeter has been continued as the principal means of dust sampling in the mines of Ontario, where South African practice has been adopted because in South Africa most careful study has been given the problem of silicosis, and very complete records of work done there are

Jan 1, 1937

Jan 1, 1922

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,' and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By W. B. Daly, A. S. Richardson

The application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable. The Ventilating Problem at Butte The main obstacle to satisfactory ventilation in the Butte mines is the normally high temperature of the granite country rock. In the present operating zone, rock temperatures as high as 120' F. have been noted, and in some parts of the district the rate of increase of temperature with depth has ranged as high as 3.5" F. per 100 ft. Other factors, such as the decay of mine timber and the oxidation of sulfide minerals in the ore bodies, contribute to raise the temperature of the air in the working places but, particularly in the development of the mines to greater depth, the naturally high temperature of the rock is of predominant importance. In few other places, probably, are the ordinary ventilating measures more hindered than at Butte. At an operating depth now exceeding 3000 ft., all of the air required for ventilation must pass through timbered shafts which, because of heavy ground, are of small size and offer great resistance to the flow of air. Shaft compartments are rarely more than 4.5 X 5 ft., and the shaft area open to the flow of air usually does not exceed 65 sq. ft.; in only two shafts is the area as great as 85 sq. feet.

Jan 1, 1934

By Robert E. Delavault, Harry V. Warren

Geochemistry in all its branches is playing G an increasingly important part in the business of mine finding. Although geochemical studies were commenced more than 50 years ago, interest in this subject did not become widespread until the late 1930's when in Scandinavia and the U.S.S.R. a whole series of investigations were initiated. Unfortunately for those in North America, the results of these investigations have only recently become available. In Canada and the U.S. geochemistry as a serious mine finding tool dates back only to the period following World War II. This article deals primarily with soils, which have found widespread acceptance as a useful tool in geochemical prospecting. Actually soils vary greatly in texture, structure, profile, and mineral background. Soil sampling poses no hardship for normal intellects, but it does assume an elementary knowledge of soil science and of the chemical problems involved in determining the absolute and relative amounts of a particular element in any particular soil.

Oct 1, 1956

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By N. Brown

From the theories of flow and fracture it is shown that the difference in reciprocals of the transition temperatures (OK) is a quantitative measure of temper ernbrittlement. Experimental data are given which support this conclusion. STUDIES of temper embrittlement have been made with various viewpoints; some involved a study of the kinetics of the reaction,',2'" others were concerned with changes in the mechanical properties," . and still others investigated the structural differences between the embrittled and unembrittled states by means of the microscope," -ray ,' measurements of electrode potential," and electrical resistivity." In all these studies, the difference in impact properties was the criterion for distinguishing between the embrittled and unembrittled states. By common agreement the difference in transition temperatures is now taken as a measure of the degree of embrittlement, and this measure is used as the quantitative measure upon which studies of the phenomenon are based. Vidal and Jolivet"' suggested that the degree of embrittlement was the same whether measured by impact or by a slow bend test. Their conclusion was based on tests at constant temperature. Jaffe and Buffum" using the impact and slow bend test showed that, for a given degree of embrittlement, the difference in transition temperatures varied with the method of testing. Hultgren and Chang" showed that the difference in transition temperature produced by the V-notched Charpy impact test was not the same as the value produced by the keyhole-notched impact test. This is a very fundamental point because there can be no true measure of temper embrittlement unless it is invariant with respect to the test method. Theory The purpose of this analysis is to show how the transition temperature depends on the stress distribution and the state of the material. The criterion for fracture may be stated as follws: where iF is some function of the principle stresses and F is a critical condition depending on the state of the metal. Similarly yielding occurs when Where is another function of the prin-ciple stresses and Y is a critical value depending on the state of the material. There is some controversy as to the exact form of the function f,.(u,, u,, us) but most experimental data give the following criterion:= where 8, and 6, = 21 or 0. Combinations of 6, and 8, give the various criteria such as the normal stress, the hydrostatic tension, and the maximum shear stress laws. Agreement is general that the octahedral shear stress law adequately describes the yield condition. where the bracketed factor will be called the design factor and depends on the stress distribution. Whether the metal decides to yield or fracture is given by the condition that The effect of temperature and strain rate upon Y has been studied by various investigators, It has been shown by MacGregor and Fisher" that

Jan 1, 1955

By M. W. Lightner

IN 1947 the steel industry rebounded from its wartime effort and produced a record-breaking peacetime tonnage of steel ingots. During the first six months of the year the industry produced 42,000,000 tons of ingots and expected to produce 85,000,000 tons for the year. With a rated capacity of some 91,000,000 tons, production was at a rate of about 93 per cent of capacity. Credit must be extended to the steel producers who have maintained this steady state of operations while faced with many problems, not the least of which was a continued shortage of satisfactory scrap. Furthermore, the steel industry started a record-breaking peacetime expansion program at a total cost of more than $1,000,000,000. This program will increase the ingot-making capacity of the country by 2,500,000 tons and should be completed in 1948.

Jan 1, 1948

By John V. Beall

THIS is not simply the story of how a water filled shaft was developed into a million-ton- a-year producing mine in the space of four critical years, although it is reason enough for telling it, but it is also the saga of an engineering achievement in which knowledge nurtured by years of experience in coal and ore mines was blended together and the best from each type of mining selected. The entire system of mining was detailed on maps by the mining engineering department before the shaft was unwatered, and subsequent development followed these plans nearly to perfection. The selection of machinery was particularly critical as it was necessary to push production from only a few headings in the early stages of development and metal mine machinery was being used in a coal panel-system of mining.

Jan 12, 1950

By Y. C. Liu, G. A. Alers

The effect of rolling reduction on the textures of Cu-A1 alloys has been investigated both by pole figure and by modulus methods. In alloys which exhibit complete copper or brass types of rolling texture, the rolling reduction has little effect on the texture except to increase the degree of preferred orientation. In alloys which exhibit a transition texture, however, increased rolling reduction increases the amount of brass-type texture at the expense of the copper-type texture. The present experimental results show that there is no one-to-one correspondence between the SFE and the rolling texture of fcc metals. Additional data taken from the literature for fcc metals also support this conclusion. On the other hand, the present and previous experimental results are shown to be in good agreement with the suggestion that the texture transition occurs at a critical value for the separation distance between two partial dislocations—a consequence of the "dislocation interaction" hypothesis for texture. formation. This critical separation occurs when the parameter .r/ub is 3.75 x 10'3. From this, a value for the SFE of 39 ergs per sq cm may be deduced for a Cu-2.85 at. pct A1 alloy. ThE correlation between the rolling texture of fcc metals and the stacking fault energy, SFE, was one of the first attempts to relate atomistic properties with the type of rolling texture.' This correlation gives a qualitative explanation for the experimental observation that the addition of alloying elements, which generally lower the SFE, changes the copper-type texture to a brass-type texture. The simplicity of this correlation had led to its general acceptance and even its quantitative use.' However, it is only a correlation and is largely based on descriptive features of pole figures, and on the poorly known SFE values in dilute alloys. Quantitative verification of this phenomenologi-cal correlation is, in fact, completely lacking. One purpose of the present study is to test this correlation. Another atomistic description for the formation of rolling texture is the "dislocation interaction" hypothesis of texture formation.3 In this hypothesis, the factor controlling the type of rolling texture depends on whether or not the separation distance between two partial dislocations exceeds a critical value. Materials having a separation of less than the critical value are supposed to exhibit a copper-type texture while those with a separation above the critical value are supposed to have a brass-type texture. At the critical value, it is expected that the material should show equal amounts of copper- arid brass-type orientations in their textures, i.e., a 50 pct transition texture. The SFE appears in this hypothesis as only one of several factors which determine the separation distance between partial dislocations. It is possible to test the validity of these two concepts by studying the rolling texture as a function of rolling reduction. Since the SFE per se is an intrinsic property of the metal, it should not, by definition, be influenced by local irregularities, such as variable stress conditions. Thus, no change in texture-type is expected to occur with changes in rolling reduction. On the other hand, according to the "dislocation interaction" hypothesis, any factor that effectively influences the separation distance of partial dislocations would be expected to change the rolling texture. Since the separation distance between partial dislocations is known to depend upon local stresses,4-6 it is anticipated that there would be an effect of the degree of reduction on the texture-type. Also, since applied stresses are more likely to increase, rather than to decrease, the separation between partials,4'5 the overall effect would be to increase the amount of material in the brass-type orientations as rolling reduction is increased. Furthermore, this reduction dependence would be most prominent in alloys exhibiting the transition texture since the distance between partials in those alloys is thought to be close to the critical value. Experimental data in the literature is insufficient to distinguish between these two alternatives. Haessner studied the effect of rolling reduction on textures in a series of Ni-Co alloys by means of the X-ray intensity-ratio technique,' and found that while one texture parameter indicated no reduction dependence the other indicated a slight dependence of the rolling texture on reduction in the range of 96 to 99 pct. As has been noticed previously, the intensity-ratio technique is a convenient but controversial method7 because there is no a priori reason to suggest which intensity-ratio would describe the texture most meaningfully. A more quantitative method of describing textures is found in terms of the orientation dependence of Young's modulus. Here, the type of modulus aniso-tropy associated with the copper-type texture is sufficiently different from that observed for the brass-type texture to allow the two types to be easily distinguishable and a quantitative measure of the amount of each can be deduced from the numerical results. This ability to provide quantitative data is particularly valuable when the two textures occur simultaneously in one alloy as is the case for the transition textures. In this paper the modulus method, supplemented by pole figure data, is used to look for an effect of roll: ing reduction the texture. Also by combining the texture measurements with recent determinations of the SFE in Cu-A1 alloys'0'" it should be possible to test for a relationship between the SFE and textures.

Jan 1, 1970

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U308 /t) (0.80 lb U308) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling.

Jan 3, 1978

By Joseph Cervik

INTRODUCTION Common methods of controlling gob gas in U.S. mines are by means of ventilation of gob areas and gas drainage through surface boreholes. Costs of drilling surface gob holes increase as deeper coal- beds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States. This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1981

By Robert Henderson

SEVERAL very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. THE ORE BODY The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. MINING SYSTEMS For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the

Jan 1, 1944

By C. K. Leith

THE outstanding fact of the mineral world today, at home and abroad, is the surplus of current production, and particularly of capacity for production, over current requirements. This is not by Any means a new condition, but never before has it loomed up in such' menacing form. - Those of us who have devoted most of our professional efforts to the discovery and development of 'new mineral supplies now suddenly find ourselves with the job apparently accomplished, waiting for some one else to find an outlet for excess mineral production before we can further. The management of the industry is in much the same boat. The psjrcho16gy of the industry has been so grooved in the direction of acquisition of, minerals that at the present moment the mineral industry confronts the new problem of surplus in more or less of a daze.

Jan 1, 1931

By J. A. Eisele, D. J. Bauer, L. E. Schultze

Approximately 100 million mt of magnetic reject tailings, which contain apatite and about 1% yttrium and rare-earth elements, exist in the eastern U.S. as a result of iron ore mining operations. At the present time, no economic process is available for recovering yttrium from this material. The U.S. Bureau of Mines (USBM) studied the problem to determine if an effective low-cost method could be found, thereby increasing our domestic yttrium reserves. [Fig. 1] is a line drawing of a photograph taken during microprobe analysis of a sample of the tailings, and shows the distribution of yttrium. Typical analysis of this material is 0.14% yttrium and 1.1% rare-earth elements (mainly lanthanum through neodymium). Over half of the yttrium is present as a hydrated Ca-Y silicate deposited along interfaces in the grain structure; whereas, the remainder of the rare-earth elements occur as Ca-Fe-RE silicates. The remaining yttrium and rare-earth elements are in solid solution with the

Jan 1, 1977

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952

By G. E. Agar, P. L. De Bruyn

Flotation is an important example of a chemical process by which one solid may be separated from other solids in a mixture. In contrast to other chemical processes such as leaching and smelting, separation of solids by flotation is characterized by the establishment of contact among three phases. In froth flotation these three phases are the solid to be floated, an aqueous electrolyte solution, and a gas, usually air. The gaseous phase may be re- placed by an organic liquid phase or this organic liquid phase may be added deliberately as a fourth phase. To gain an understanding of the flotation sys- tem, it is therefore necessary to study the chemical and physical properties of surfaces and to establish the effect of changes in composition of the bulk phases on the nature of the three interfaces, solid-gas, solid-liquid and liquid- gas. With very few exceptions inorganic solids are completely wetted by the aqueous phase so that the first step in flotation is to replace partially the solid-liquid interface by a solid-gas interface. This displacement process is accomplished by the addition of suitable reagents to the aqueous phase. The resultant surface reaction leaves the solid surface with a hydrophobic film. Although the primary objective of these reagent additions is to alter the solid surface, chemical reactions between the added chemical species and those species derived from the dissolution of the solids are unavoidable. For a quantitative description of such reactions and for the determination of the feasibility of a proposed reaction, we rely on available thermodynamic data. The application of thermodynamic principles to flotation systems has contributed much to our understanding of flotation. The changes in thermodynamic properties such as free energy and chemical potential are accessible to experimental determination, and a knowledge of their magnitude allows us to develop and predict a chemical mechanism oy which a solid becomes floatable. In this chapter it will be assumed that the reader has a working knowledge of the general principles of thermodynamics and solution chemistry. A complete discussion of the physical chemistry of flotation must include a treatment of solubility relations, complex ionic equilibria, reaction potential, and the elements of electrochemistry, especially those dealing with reversible electrical cells. The principles related to all of these features of the flotation system will not be discussed in this chapter. The discussion will be concerned with the thermodynamics and electrochemistry of surfaces and the electrical double layer model of the interface.

Jan 1, 1962

By K. L. Komarek

Based on theoretical and experimental evidence a discussion follows of the behavior of phosphorus -bearing iron ores in the R-N Direct Reduction Process and suggestions are made of methods of reducing the amount of phosphorus in the metallic end product. In ferrous metallurgy a direct reduction process is one in which iron ores are reduced to metallic iron with gaseous or solid reductants without the appearance of a liquid phase. A number of attractive features have induced several companies and government agencies to invest in the development of direct reduction processes. A summary of all direct reduction processes up to 1954 has been given by Barrett,' and Wiberg,2 and Willems3 have reviewed the most recent developments in this rapidly expanding field. Many difficulties have been encountered in direct reduction processes and the nature of these difficulties has varied from process to process. One problem common to almost all of them is the removal of phosphorus which is one of the reasons for the rather pessimistic outlook given by some government publications4'5 to direct reduction processes. In this paper an attempt is made to give a theoretical explanation of the variations in phosphorus removal observed in the R-NY Direct Reduction Process. However, many conclusions are general enough to be applicable to other processes. Most iron ores treated by the R-N process yield products lower in phosphorus than the original ore. A qualitative account of the factors has been given by Stewart, Reed, and Herasymenkoe but the erratic removal of phosphorus from some ores and the general importance of this problem make a more careful analysis of the theoretical aspects desirable. In the R-N process mixed ore or balled fines, ex-

Jan 1, 1963

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980