Search Documents

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By George A. Guess

THE increasing demand for greater speed and more accuracy, in making daily assays of ores and products from mills treating material containing but very small quantities of lead and copper, has caused the older analytical methods to be supplanted by new ones devised to meet the needs of modern work. For " control " work in copper analyses, I had, previous to the present equipment, introduced in my laboratory the ordinary electrolytic method, using hollow cylindrical electrodes, and with these I began a series of experiments in determining the lead-content of daily mill-samples and controls. The results, proving accurate and satisfactory, I then devised, with Mr. H. E. T. Haultain, a cheaper electrode than the ordinary jacket electrode, which costs from $15 to $20,-the expense of the older form making the installation of many units very costly. The form of cathode finally adopted as the most satisfactory, shown in Fig. 1, is cut from 0.001-in. platinum foil. It is 12.5 cm. long, and is divided into a blade 4 cm. wide and 6.25 cm. long, and a tongue 0.7 cm. wide and 6.25 long, the immersion area being 50 sq. cm. and weight 1.5 grams. The blade is first sand-blasted and then corrugated lengthwise, in order to impart the necessary rigidity. Strips of platinum foil 0.001 in. thick, 12.5 cm. long and 0.5 cm. wide, having a median corrugation, form the anodes. Three electrodes are used in each cell, one anode in the middle and one cathode oil each side of the anode. These electrodes are connected to slotted alumi¬num terminals, in which they are held by contact pressure. The terminals are -in. rods, projecting 2 in. horizontally in front of the wall of the cabinet.; at the back the middle electrode (anode) is connected with one pole of the current, and the two outer ones (cathodes) with the other pole.

Nov 1, 1905

CONTENTS PAGE East Texas, except the Gulf Coast-H. Vance 3 Gulf Coast-L. P. Teas 8 Texas Panhandle-C. C. Rae 16 North Central Texas-H. F. Smiley 23 North Louisiana, South Arkansas and Mississippi-B. C. Craft 25 Oklahoma-C. H. Pishny, Raymond M. Carr and E. J. Dickinson 31 Kansas-E. A. Koester 35 Rocky Mountain District-C. D. Johnson 46 Illinois and Indiana-T. Wasson 49 Michigan-T. Wasson 52 Eastern States-P. D. Torrey and W. H. Young, Jr 58 West Texas and New Mexico-W. V. Vietti. Published as a Supplement.

Jan 1, 1933

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical specifications, color demands must also be met. The firm of which I have the most knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By Frederick T. Williams

The purpose of this paper is to discuss the relative merits of the large 31/8-in. machine and the small 2 1/4-in. tappet machine in driving development-headings; and although the data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winzing. Recently we drove two parallel cross-cuts through the same formation, using a 3 1/8-in. machine at the breast of one crosscut, and a 2 1/4-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties, the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, the air-pressure or the experience of the operating crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to "pull " the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated andesitic or pho-nolytic breccia, true massive andesite, trachytic phonolyte, tuffs, and along dikes of decomposed basalt and hard phonolyte. In every instance a satisfactory record was made. The headings here describe? mere driven through highly indurated andesitic breccia, having a hardness of from 5.2 to 7.2 and a sp. gr. of from 2.2 to 2.8. The action of the breccia under the drill was not materially different from that of ordi-

Jan 1, 1907

By C. W. Mac Gregor

THE observation of the flow layers, or Lüders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-steel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are in reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45° to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ner, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45° to the principal stress direc-tions at the point. As examples of the latter may be mentioned the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subjected to internal pressure only, etc. Hence if the flow layers are observed from an experiment, the shear-stress trajectories -the curves indicating the directions of the maximum shearing stresses in the body-may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45° to the principal stress directions, the family of principal stress trajectories, or the curves indicating the directions of the principal stresses, may be thus obtained. Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowan;1 in duralumin and other aluminum alloys, by Dawidenkow, 2 Elm,3 Fell, and others; in copper and copper-alloy crystals, by Elam;5 in brass by Elam;5 in brass wires by deForest;6 in higher carbon steels, tungsten steel, and

Jan 1, 1939

By Will B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 5, 1960

By George W. Maynard

For an account of the discovery and the determination of chromite on Port au Port Bay I am indebted to Mr. Obalski, Government mining engineer for the Province of Quebec. He writes: " In June, 1894, with the authorization of our Government, I went to Newfoundland to examine some asbestos property. Passing through Halifax, I had interviews with some gentlemen who told me that besides the asbestos there was in the same district a big deposit of iron-ore. They handed me some specimens, and, after ascertaining that they were not magnetic, and learning that they were found in serpentine, I said they were chromic iron. I visited the place on June 27, 1894, and confirmed my opinion, pointing out at the same time the importance of the deposit, as appears in my report of July 9, 1894. I do not claim any credit for the discovery of chrome-ore in Newfoundland; but, as a matter of fact. when I came in contact with the Halifax gentlemen they did not appear to know the nature or the value of the mineral until I mentioned to them that it was chromite. "' Mr. Obalski's report was mainly devoted to the asbestos-deposits. That portion relating to the chromite was as follows: " On the right side of the creek there is a show of chromic iron of good quality, which appears scattered through the serpentine in several places on the face of the cliff for 40 to 50 feet. A few boulders are found farther up at a distance of 100 feet, and also in the ckeek itself. From this point the deposit exists on a relatively large area, the widest exposures being from 6 to 7 feet. Chromic iron deposits in serpentine rock have no regularity, and are merely pockets. In the case of the property in question this rule is not changed, but the pockets look to be of large extent, and could be easily worked." My own preliminary investigation of the property was made

Jan 1, 1898

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

Jan 1, 1957

By Charles P. Williams

THE successful production of zinc white or oxide on a commercial scale in this country dates from the issue of the patent of Samuel Wetherill, for the preparation of the material (November, 1855), and

Jan 1, 1877

By Charles P. Williams

The successful production of zinc white or oxide on a commercial scale in this country dates from the issue of the patent of Samuel Wetherill, for the preparation of the material (November, 1855), and

By C. K. Leith

CERTAIN ideas on iron and steel sanctions to follow originated in a series of conferences held under the joint auspices of the War Department and Brookings Institute in Washington last spring. The views presented may be regarded as those of substantial segments of the steel industry. In view of the fact that steelmaking capacity can be so quickly converted to the production of armament, any effective control must necessarily include the entire steel industry and not solely the parts devoted to the production of implements of war. It must also be exercised all the way from production and shipment of raw materials through their ultimate conversion into finished products and use. Control will be dis- cussed under two main headings: (I) control of raw materials at the source; (2) control of steel capacity within the Axis countries.

Jan 1, 1944

Some 15 years ago, Dr. Adolf Schmidt, director of the Magnetic Observatory in Potsdam, Germany, developed an instrument, which was a modification of Lloyds balance, for the measurement of the vertical component of the earth's magnetism in the field. There was a keen demand for this because (1) it was desirable to have a field instrument that would measure the component of the earth's magnetism which stands in the closest and simplest relation to the configuration of the subterranean magnetic formations-the vertical component; (2) it was desirable to have an instrument that was not only more sensitive but also more reliable than the existing vertical magnetometers (the dip needle, for instance). The application of the magnetometer in oil geology demanded such an instrument, because the magnetic disturbances produced by most types of magnetic formations associated with the occurrence of oil (salt domes, faults, anticlines with crystalline core, etc.) are too small to be detected with the ordinary dip needle. The writer can prove, by some investigations recently made for the U. S. Bureau of Mines, that these instruments may be used also to very great advantage in mining, because they are capable of measuring anomalies which are as great as twice the normal strength of the earth's magnetic field. Even for such anomalies, the field balance is more advantageous than the dip needle. First, the instrument rests on a firm support and can be adjusted in the proper azimuth, which insures measurement of the vertical intensity only, without a part of the horizontal intensity, which is very important for the interpretation. The readings give the vertical intensity in linear terms and not as a function of an angle; and the field balance is insensitive to temperature when used with scale values that are adequate for the determination of large anomalies. In another phase of mining, the gold placer work, the field balance has also shown excellent results for which the dip needle is not adequate. What has been said about the dip needle holds also, though to a lesser extent, for two other types of vertical variometers recently used, the Tiberg balance and the Thomson-Thalen magnetometer.

Jan 1, 1929