Search Documents

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division OFFICERS AND COMMITTEES S D Michaelson, President J W Woomer, President-elect Elmer A Jones, Past President C E Lawall, Eastern Regional Vice-President G Donald Emigh, Central Regional Vice-President J D Forrester, Western Regional Vice-president R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1958

By J. T. Burwell

THE crystal orientation in silicon iron that has been given a particular treatment described by Goss,1 has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualita-tive. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200, It is now generally agreed that Goss's original conclusion' that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom.

Jan 1, 1940

ROBERT H. LEACH, Chairman ROBERT F. MEHL, Past-Chairman D. K. CRAMPTON, Vice-Chairman E. M. WISE. Vice-Chairman W. M. CORSE, Treasurer LOUIS JORDAN, Secretary 29 West' 39th St., New York, N. Y. Executive Committee 1940 1941 ARTHUR PHILLIPS W. P. SYKES L. E. SCHUMACHER E. A. ANDERSON CARL E. SWARTZ D. L. COLWELL 1942

Jan 1, 1939

By R. B. Adair, J. S. Browning

The Bureau of Mines conducted laboratory research to determine the applicability of heavy liquid separation to the evaluation of certain mica ores and plant products. After careful standardization of the particular mica ores and associated gangue, accurate analysis of muscovite content could be obtained from results of heavy liquid separation. Where applicable, the method should be particularly suited to the analysis of ores and control of plant operations wherein savings in time would be of considerable advantage. Specifically, there are many instances where a quick plant control method should enable the production of a more uniform grade of mica concentrate. The laboratory use of various heavy liquids for separating minerals of different specific gravities has been recognized for many years.1-8 Sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations. A standard method of analysis for mica in ore samples has not been published or generally accepted by the mica industry. Recently, the U.S. Bureau of Mines investigated methods for analyzing mica by heavy liquid separation. This report has been prepared to make the methods available to others who may need simple, relatively rapid methods of determining the mica content of ores and plant products. The heavy liquid method of mica determination has recently been adopted by one of the major mica producers for evaluating exploration and mill control samples. DESCRIPTION OF THE ORES AND HEAVY LlQLllD The weathered mica pegmatite ores used in the investigation were obtained from commercial mica op erations in Alabama, Georgia, and North Carolina. The major mineral constituents of the ores were muscovite, quartz, kaolin, and minerals of the feldspar group. The ores also contained minor quantities of biotite, limonite, and tourmaline. A comparison of the specific gravities of the major constituents of the ores (muscovite 2.76 +, quartz 2.65, kaolin 2.61, and feldspar 2.57), indicates that an effective separation of muscovite from the other minerals can be made in heavy liquids at a specific

Jan 1, 1968

By C. K. Rose, J. H. East

Proved oil shale reserves in the Green River formation in Colorado, Utah, and Wyoming dwarf present U. S. petroleum resources. Indications are that the appetite for petroleum products will continue to grow and that this potential source of liquid fuels and related byproducts cannot be disregarded. As a part of its synthetic fuels program, the U. S. Bureau of Mines has opened a mine in the richer beds on the naval oil shale reserves. In addition to supplying material for retorting and refining studies, the development of methods, procedures, and equipment for mining oil shale on a large-scale commercial basis is of the greatest importance.

Oct 1, 1955

By H. R. MacMichael

IN the Chihuahua district of Mexico the first smelting was that inaugurated by the early Spaniards for the production of silver bullion. The ores treated were high in silver and lead. Silver-lead bullion was first produced and the lead then cupelled to waste, with the slag produced running from 5 to 10 per cent in lead and about 25 to 40 per cent silica. The ore was mined by peon labor, often being carried out of the mine on the backs of the men, and then transported by burros. Furnaces were of primitive construction, adobe or rock being used in the earlier period and some iron later when it became available. Blast was originally supplied by bellows manually operated. Such smelting was carried on to a greater or lesser extent until the latter part of the last century, and so extensive was it that many hundred thousand tons of leady slag remained to be treated in modern furnaces. In 1908 a smelter was placed in operation at Chihuahua by the American Smelting & Refining Co. At that time the ore was practically all oxidized and by a little selection, self-fluxing mixtures could be made, but with an average lead content usually under 10 per cent and sometimes as low as 7 per cent. The bullion produced would carry from 150 to 300 oz. silver per ton. The slag made approximated 30 per cent SiO2, 42 per cent FeO, 21 per cent CaO, and perhaps 3 per cent Zn. The ores varied from hard, coarse material which was passed through a crusher, to a considerable quantity of fines which had to be smelted as it came, as crushing the coarse was the only preparation for smelting.

Jan 1, 1933

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By W. L. Fink, L. A. Willey

This paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium relations have been determined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and aluminum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith † suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extentl,2,3 The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are distinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns. Previous Investigations The solid solubility of magnesium in aluminum has been well established by the work of Dix and Keller4, Schmid and Siebe15, and Saldau and Sergeev6. There is no agreement as to the composition of the magnesium constituents at the aluminum end of the binary aluminum-magnesium system. Hanson and Gayler7 report Mg2Al3; Boyer8 found that the alloy

Jan 1, 1937

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By H. H. Uhlig

SINCE its first mention in the literature in the eighteenth century1,2 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ? Faraday,7 in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the poten-tial at which a negative ion (e.g., Cl-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By P. E. Phillips

INTRODUCTION Rocky Mountain Energy is the mining subsidiary of the Union Pacific Corporation, and has been active m uranium exploration since 1966. Since 1970, RME's uranium activities have been funded 50% by Mono Power, the fuels supply division of Southern California Edision. RME and Mono recognized the need for development of new methods for recovering low grade uranium deposits, and contacted Halliburton Services in regard to in situ leaching, because of Halliburton oil industry experience. As a result, a joint venture between the three parties was formed in 1974. BEAR CREEK The first ISL test was at the Bear Creek deposit in the Powder River Basin of Wyoming, about 60 miles north of Douglas. The mineralized sand is the tertiary Wasatch formation, which is an arkosic sandstone. The sand typically contains about 10% clay. The predominant clay being montmorillonite with some kaolin and illite. The roll front type trends occur along the flanks of old stream channels. This deposit was being considered for exploitation as an open pit mine. Routine amenability testing indicated it was quite amenable to a conventional acid leach, consuming about 50 lbs. of sulfuric acid per ton of ore in an agitation leach, while recovering more than 95% of the uranium. Hydrology testing indicated a permeability of about 1 darcy. The groundwater has a pH of about 8. 0 and TDS of about 1200. Test Facility The Bear Creek test was a summer-only operation, with no effort towards weather-proofing. Uranium was removed from the recovered leach solution by fixed bed ion-exchange columns. Loaded resin was eluted with strong sulfuric acid. The recovery plant was designed for simplicity of operation, with little concern for the grade or form of the yellowcake product. The plant was constructed of PVC piping and valves, fiberglass reinforced tanks, and stainless steel pumps. All waste streams were directed toward a lined evaporation pond. Wellfield The test pattern was a 30 foot radius 5 spot, with wells fully penetrating the 30 foot ore sand to a total depth of about 165 feet. The injection wells were three-inch PVC with slotted casing, while the producer was eight-inch I. D. , with a stainless steel screen. The eight-inch well was necessary in order to accommodate a six-inch stainless steel pump. Wells were cemented using cement baskets, at the top of the sand, to contain a latex acid resistant cement. Leach Conditions The lixiviant generally contained from five to seven gpl sulfuric acid, and about 0. 5 gpl hydrogen peroxide. The pH was generally 1.4 and EMF was usually -550 millivolts. Injection rates were rather variable from well to well, with a total injection rate between 12 and 25 GPM. Production rate was set at 25 GPM, since the production pump could not be throttled more than that. Approximately two pore volumes of solution were injected during the three-month test. Leach Results Injectivity was quite variable, but was generally rather poor, because of poor completion techniques. The problem stemmed from injecting before the injection wells had been completely cleaned of drilling mud. Pregnant solutions averaged about 50 ppm U308, with groundwater dilution varying from 10 to 50%, depending on the injection rate. Injectivity did decline with time, probably as a result of contamination of the well faces. A total of 1000 lbs U308 had been recovered when the test was shut down. This probably represented about 10% of the mineral under leach.

Jan 1, 1979

By L. B. Gittinger

Sulfur is a nonmetallic element widely distributed in nature. It constitutes 0.06% of the earth's crust but only a very small portion occurs in sufficiently concentrated amounts to justify mining. Sulfur occurs in practically all animal and plant life. It constitutes approximately 0.09% of the elements in the oceans; it has been found in meteorites. Sulfur was known and used by man before recorded history. The American Chemical Society approved spelling for the element is sulfur. The English spelling sulphur is used commercially in the United States. In ancient times, sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Sulfur is found naturally in the elemental form in subsurface deposits associated with gypsum and anhydrite in salt domes and sedimentary formations in evaporite basins and in solfatara-type deposits associated with volcanoes and mineral springs. Sulfur occurs also in molecular combination in ferrous sulfides (pyrites and pyrrhotite) and nonferrous sulfides (copper, lead, zinc, and nickel), and in mineral sulfates (gypsum and anhydrite); as hydrogen sulfide contaminant in natural gas; as organic compounds in crude oil and tar sands; and as pyrite and organic compounds in coal and oil shales. Sulfur resources are abundant and exist throughout the world but the extent to which they can be classified as reserves is greatly circumscribed by prevailing prices and technology. Estimates of world sulfur reserves are compiled by the U.S. Bureau of Mines. A compilation of reserves by area and source of sulfur published in 1970 and presented here as [Table 1] totaled 2.47 billion tons (Lewis, 1970). The effect of the decline in prices which has occurred since the earlier estimate is dramatically illustrated by the 1972 estimate of the U.S. Dept. of the Interior which shows world sulfur reserves of only 1.2 billion tons (Anon., 1972d). Sulfur is produced commercially from one or more sources in nearly 70 countries of the world. World production of sulfur in all forms totaled 41.6 million tons in 1971. (Sulfur statistics given in this chapter are long tons.) Native deposits, sulfides and oil and gas contributed, respectively, 31, 41, and 25% of world production (Table 2). Of the sulfur produced from native deposits, salt domes accounted for 54% and evaporite basin deposits, 44%. Volcanic deposits are of little significance except for local consumption. The past two decades have seen important shifts in the world's sulfur sources. In 1950, native deposits and sulfides each supplied about one-half of the world's production. During the 1950s, sulfur recovered from oil and natural gas grew rapidly, representing about 10% of the total by 1960. Since then, the petroleum industry has continued to increase its relative importance as a source of sulfur, representing more than 30% at 1972 year-end. Sulfur is generally classified as elemental or nonelemental for statistical purposes. Elemental sulfur is sulfur produced in the pure, uncombined form. It includes production from native deposits, as well as that recovered in the elemental form from oil and natural gas or other sulfur-bearing materials. When produced from other than native deposits, it is generally referred to as recovered elemental sulfur. Nonelemental sulfur is that which is utilized commercially in molecular combination with other elements, such as sulfides or sulfates. Elemental sulfur is being produced from salt dome deposits in the Gulf Coast region of the United States and the Isthmus of Tehuantepec in Mexico, and from evaporite basin deposits in west Texas, Poland, Sicily,

Jan 1, 1975

By E. V. Daveler

THE milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. CHARACTER OF ORE The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver 0.10 oz. Magnesia 0.4 per cent. Silica 59.7 per cent. Sulfur 1.2 per cent. Iron 5.2 per cent. Lead 0.1 per cent. Alumina 21.4 per cent. Zinc 0.2 per cent. Lime 5.0 per cent.

Jan 1, 1920

By G. R. M. Del Giudice, A. M. Sadler, Arthur F. Taggart, M. Hassialis

FLOTATION of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest days of flotation that certain of the nonsulphide nonmetal minerals-e.g., sulphur and graphite-would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection, 1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis. 4 5-1 Air levitationt of certain oxidized minerals, both metalliferoust and nonmetalliferous, and separation thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years .7 This paper presents evidence that the principles underlying the air levitation of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentration, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levitation. The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material. By using large quantities of oil, it is possible to form substantially air-free oil-bound masses or granules of nonsiliceous minerals and to

Jan 1, 1937

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth's surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By George Sachs

THE process of recrystallization has not as yet been explained satis-factorily. Some definite conclusions could be drawn from recent investi-gations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth 1and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a sheet is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a-simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found., It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation." Such deviations

Jan 1, 1940

By William B. Plank

STATISTICS just released by the American Society for Engineering Education and given in the table, show that the total current enrollment of 200,227 in the 220 engineering schools of the U. S. and Canada represents a gain of 9.8 pct over a year ago, while the mineral engineering enrollment in the U. S. of 9826 shows a gain of only 4 pct in that field. The spurt in the mineral group shown last year is thus slowed down to less than one half of that in the whole engineering student body. Last year, it was growing more rapidly than the whole engineering group.

Jan 5, 1954

By J. H. Bechtold

Tensile properties of annealed molybdenum were investigated from 1000" to—200°C. In the vicinity of room temperature a well-defined transition in tensile properties occurs. Reduction in area decreases from over 80 pct to 0 pct and, simultaneously, the yield strength increases about 60,000 psi. MOLYBDENUM, tungsten, iron, and many other metals and alloys with the body-centered cubic and hexagonal close-packed crystal structures change from ductile to brittle behavior over some relatively narrow temperature range. The temperature at which this transition in ductility occurs depends on chemical composition, microstructure, and method of testing. When fine grained, completely recrystallized molybdenum of commercial purity is tested in uniaxial tension at a slow strain rate, the transition occurs at slightly below room temperature.&apos; Iron2 and tungsten3 tested under similar conditions become brittle at temperatures close to the boiling point of nitrogen, — 195°C and at about 200°C, respectively. A sharp change in ductility is uncommon in metals with the face-centered cubic crystal structure, however, a relatively sharp transi- tion in notched bar impact properties has been observed below room temperature in a face-centered cubic copper-antimony alloy.4 A transition from ductile to brittle behavior is usually explained by the concepts originally developed by Ludwik,5 and discussed and elaborated on by others including Orowan,6 Hollomon and Jaffe,7 and Gensamer8 In brief, there are two aspects to strength, first the resistance to flow and second the resistance to fracture. Both are functions of temperature, strain, strain rate, stress system, composition, and microstructure. With decreased test temperature the flow stress required to initiate plastic deformation increases more rapidly than the fracture strength and brittle fracture occurs at that temperature where the yield strength equals or exceeds a brittle fracture strength. This investigation was conducted to determine the effects of temperature, strain, and rate of straining on the flow and fracture strengths of molybdenum above, through, and below the ductile-to-brittle transition. Other variables were held constant during testing. This information is believed to show

Jan 1, 1954

By Carl Keuffel

THE manufacture of optical glass is a new industry in this country. In 1914, after the war started, the supply of optical glass from Europe was cut off, but as there was a fairly large stock of glass on hand, it was not until the end of 1915 that the optical instrument makers made serious efforts to produce their own glass. These early attempts were generally made by practical glass men and, due primarily to the fact that very little scientific help was used, the first attempts were unsuccessful. It was not until the whole problem was attacked by technically trained men who used advanced methods of research that good results were obtained. These researches proved that the accurate control of the temperature was a most important factor in the manufacture of optical glass. The early glass maker judged temperatures with his eyes; later, Seger cones were introduced into the furnace at various stages of the melt. Then radiation, indicating and recording pyrometers with rare-metal thermocouples were introduced. Now, in addition to these, an optical pyrometer every hour or so is sighted right into the pot and on the molten glass. Figs. 1 and 2 show how pyrometers are used to control the melt. InFig. 2, Y is the clay pot in which the batch is melted to glass within the furnace X. The rare-metal thermocouple S, protected by a clay tube, extends through the wall and about 4 in. into the furnace. This couple is connected to an indicator T and a recorder U so that a complete record of the furnace temperatures is obtained. The section of the curve ABCD, Fig. 1, shows how gradually and carefully the clay pot must be heated to get rid of moisture AB and during the calcining at CD. The stem of an expansion pyrometer R is extended through a hole in the door Z of the furnace and into the pot in order to more closely follow the temperatures of the clay pot itself during the burning process, that is from A to D. After the pot is calcined, the temperature can be rapidly raised to E (about 1430° C.); from E to F this temperature is much higher

Jan 9, 1919