Search Documents

By C. M. Wayman, M. Miyagi

COMPARED to many of the binary alloys of iron, Fe-Ir alloys have received very little tud.'' Virtually nothing is known about the Fe-Ir equilibrium diagram' except for a few details concerning the liquidus-solidus positions for dilute iron-based alloys. It is reported1 that the y to a transformation temperature in Fe-Ir alloys (up to 40 wt pct Ir) is composition-dependent, varying from -900°C for pure iron to 0" to 100°C for Fe-40 pct Ir in an almost linear manner. The y to a transformation appears to be reversible,' the transformation hysteresis width increasing with increasing iridium content. In a qualitative way, the composition dependence of the y to a (and vice versa) transformations appears similar to those in the widely studied Fe-Ni system. In that the y phase (in Fe-40 pct Ir) can transform at -1000C, it

Jan 1, 1967

By I. N. Zavarine

THE observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accom-panied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observa-tions that constitute the subject of the present paper.

Jan 1, 1939

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By R. C. Thompson

THE lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 45o-ton operation. GENERAL DESCRIPTION The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1947

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

By Walter Harvey Weed

Introductory.............449 Summary oF Types............452 I. The Virgilina Type...........452 The Virgilina mines...........452 Location.............452 History.............453 The rocks of the district..........453 The veins.............454 Notes on the mines.... 458 The Holloway. 458; Yancey and Durgy. 465 ; Copper World. 467 ; Frazier. 467 ; Thomas. 467 ; Anaconda. 468; Blue Wing. 468; High Hill. 472; Dorothy.......474 II. The Gold Hill Type...........474 The Gold Hill mine...........475 Location.............475 History............• 475 Surface improvements.......... 476 The rocks............478 Vein.phenomena...........478 Character of the ore..........481 Origin of the ore...........481 Notes on the mine.workings.........482 Other occurrences of ore-deposits of the Gold Hill type.. .. 483 III. The Ducktown Type..........484 The Ducktown mines...........485 Other examples of the Ducktown type....... 494 Alabama mines...........494 North Carolina examples : Ore Knob.......496 Virginia examples..........497 IV. The Catoctin Type.. ......... 498 General characteristics,......... 498 The Linden district...........499 General distribution of the Catoctin type.......503 Introductory. In the early history of this country the existence of copper in the Appalachian region was well known. but no mining mas attempted until the discovery of the Ducktown deposits in

Jan 1, 1901

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

By Tommy Wilson

OIL well drilling fluids have become a vital part of the drilling industry during the past 25 years. From chance usage of drilling mud at the fabulous Splindletop field in 1901, drilling fluid control has become an extremely technical and exacting science. Drilling for oil today involves exploration at depths ranging to 21,000 ft, nearly 4 miles. Geological formations encountered at these depths offer a tremendous challenge to the production, research, and service facilities of any drilling mud company.

Jan 5, 1954

By A. E. Jenkins, L. A. Baker, N. A. Warner

The electromagnetic levitation technique has been successfully applied to rate studies of the de-carburization of liquid Fe-C alloys from 5.5 to zero pct C at 1660°C using gas mixtures containing 1 to 100 pct CO2 with CO or helium as diluents. The rate was shown to be independent of carbon concen -tration in the melt and only slightly affected by total pressure. The results were shown to be consistent with control either wholly or predominantly by gaseous diffusion. As well as avoiding side reactions with the crucible, levitation allowed precise calculation of reaction rates since the geometry of the system was accurately known. It also enabled interpretation using the established mass-transfer correlations for a gas flowing past a single sphere, The existence of gaseous-diffusion control and the extremely high rates of reaction reported for gas flowing past small spheres are of great practical significance in relation to current investigations into the use of spray-refining techniques in continzcous steelmaking. PREVIOUS work on the kinetics of carbon removal from liquid iron has generally involved the use of oxygen as the gaseous oxidant. Investigations have been made on commercial steelmaking furnaces and in addition laboratory-scale experiments have been attempted with a slag phase present. The general lack of agreement and the obvious difficulty in interpreting the results is at least partly due to the complexity of the systems used. This work has been reviewed by carter1 and more recently by Bods-worth2 and ward.3 The gas-liquid metal reactions have also been studied with slag-free melts by the conventional technique of blowing oxygen onto the melt contained in a crucible. The reaction between the oxidant and carbon could be followed by sampling either the melt or the gas phase. Side reactions with the crucible material have precluded direct interpretation of the results. Fujii, 5-7 using O-A mixtures, attempted to correct for the crucible reaction and reported that the reaction between carban and oxygen occurred at the melt surface and was controlled by gaseous diffusion for carbon contents greater than a critical value and by carbon-diffusion control in the metal for carbon contents less than the critical. The critical value was given as approximately 0.15 pct C. However, whereas this was the case for oxygen contents in the gas stream up to 10 pct, between 10 and 20 pct the rate was found to be approximately independent of oxygen content, and Fujii attempted to explain this observation by postulating the presence of an oxide "film".7 Turkdogan et a1.' have studied iron fuming during decarburizing and suggested gaseous-diffusion control of the reaction above a critical carbon concentration, given as approximately 2 pct C. Filippov9-12 reports in a similar manner to Fujii but makes no mention of the crucible reaction with the carbon in the melt, even though this would be expected with the temperature, crucible material (MgO), and carbon contents used. Both CO2 and O2 were used as oxidant gases. In the present work the decarburization of liquid Fe-C alloys was studied using an adaptation of the electromagnetic levitation technique, and thus the complexities introduced by crucible side reactions were eliminated. In this technique a single sphere of the Fe-C alloy is freely suspended and heated by electromagnetic induction in a flowing stream containing the oxidant gas. The full range of carbon levels up to saturation was studied, the temperature of the melts in this instance being held constant at 1660°C. The oxidant was CO2 which was used either pure or in association with a diluent gas, the total gas pressure being maintained either at 1 atm or at a reduced pressure. Thus the reaction under study was:

Jan 1, 1964

By Joseph W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles, as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain.

Jan 3, 1960

New York Meeting, October 16 and 17, 1913.-The One Hundred and Sixth meeting of the Institute for the reading and discussion of professional papers will be held in New York City, on Thursday and Friday, October 16 and 17, 1913. Headquarters will be at the Institute office in the Engineering Societies Building, 29 West 39th Street. The sessions will be held in one of the assembly rooms of the building. Because of the many valuable papers on iron and steel obtained with the assistance of the Iron and Steel Committee, which papers could not appropriately be presented and discussed at the Montana meeting, this October meeting of the Institute is held for the purpose of reading and discussing these papers, most of which will be printed and distributed in advance. The members of the following societies have been invited to attend the meeting, and several have accepted and declared their intention of taking part in the proceedings: American Society for Testing Materials, American Iron and Steel Institute, American Society of Mechanical Engineers, American Society of Civil Engineers, American Institute of Electrical Engineers, American Foundrymen's Association. The meeting will be conducted under the auspices of the Iron and Steel Committee, and the latest revised program of the proceedings will be found on page xi, under the notes of this Committee.

Jan 10, 1913

By T. D. Yensen

It is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current losses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that, indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use. Until the beginning of the present century, Swedish charcoal iron was regarded as the best grade of iron for magnetic purposes, and even now it ranks high among the various grades used. About that time Sir Robert Hadfield1 produced a number of iron alloys that revolution-

Jan 1, 1916

Arizona Bureau of Mines and College of Mines and Engineering, University of Arizona, Tucson, Ariz. Lists of the maps and bulletins available will be sent upon request to G M Butler, Director, Arizona Bureau of Mines, Tucson, Ariz Bulletin 119, A resume of the geology of Arizona, by N. H Darton, is sold for $1, postpaid Fourteen other bulletins, any five of which may be had free of charge (additional numbers may be purchased for 10 cents each) are available as follows - 106, A geological reconnaissance of the Tucson and Amole Mountains, by Olaf P Jenkins and Eldred D Wilson, 114, Fluorspar, by M A Allen and G M Butler, 120, Gold and copper deposits near Payson, Arizona, by Carl Lausen and Eldred D Wilson, 122, Quicksilver resources of Arizona, by Carl Lausen and E D. Gardner, 123, Geology and ore deposits of the Courtland?Gleeson region, Arizona, by Eldred D Wilson; 125, The mineral industries of Arizona, by J B Tenney, 126, Asbestos deposits of

Jan 1, 1933

By C. W. Parmelee

THE ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its used except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample' of coal commonly used in pottery ovens has something like this quantity of sulfur." PER CENT. Total sulfur 1.20 Sulfur in the ash 0.11 Volatile sulfur a 1.09

Jan 9, 1919

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By J. L. Wyatt

The electrical resistance of titanium as a function of purity and temperature was measured from —325" to 2800°F. Two points of inflection in the data plots were found, and an increase in resistance with increase in temperature above the transformation was observed. IN 1948 Greiner and Ellis' reported on the thermal and electrical properties of titanium, including a study of the effect of temperature on the electrical resistance. The materials used in the research were obtained from the United States Bureau of Mines, where powder metallurgy techniques were being employed for consolidation purposes. These authors found a decreasing resistance with increasing temperature above 1625°F, and concluded that the latter temperature represented the point of transformation from hexagonal close-packed to body-centered cubic structure on heating. They reported a specific resistivity value of 55x10-6 ohm-cm, and showed that dp/dt was positive, decreasing with increasing temperature above ambient. In one of his early texts Hume-Rothery2 mentioned that certain metals, including titanium, exhibited minima in plots of resistance vs temperature. He indicated that this occurred at 212°F. Reporting many years ago on the effect of temperature on the electrical resistance of zirconium, de Boer and Fast³ showed that phase transformation in this sister metal occurred over a range of temperatures, the extent varying with its purity. Graphs of resistance vs temperature, showing transformation effects over a range of several hundred degrees, were presented for relatively impure metal. In the latter case the resistance decreased with increasing temperature throughout the region of partial phase transformation, thereafter increasing as predicted for normal metals by modern theories of the solid state. Since the quality of metal used in previous studies was substandard compared with iodide-type titanium, and in view of the fact that there seemed to be some rather unusual observations in the reported literature, it was decided to undertake a more extensive study of the thermal effects using high purity titanium, and to include temperature ranges beyond those which had been studied in order to ascertain whether or not the characteristics of zirconium would be duplicated. Experimental Materials Materials used in this investigation included commercial quality titanium (Ti-75A produced by the Titanium Metals Corp. of America) in the form of ¼ in. diam rods, and high purity iodide titanium (produced by the Foote Mineral Co.) in the form of crystal bar of irregular size. The latter was cold-swaged into rod form and machined to the desired size. Lead wires to all specimens consisted of 18 gage Ti-75A. Chemical analyses of the stock materials are given in Table I. Experimental Procedures Specimens 2½ to 3 in. in length were prepared with diameters nominally 0.15 to 0.20 in. Two holes,

Jan 1, 1954

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

By ir. H. Eraly

The allocation of miners to teams, and of teams to production faces, is complicated by the high degree of absenteism of miners in Belgium. Therefore, the exact knowledge of who is actually present at the beginning of a shift and of the exact skills of those present, enables the foremen and mine captains to constitute their teams before all men go down into the mine in the most effective way possible. This paper describes the system of attendance recording and of displays which the foremen use to constitute their teams and/or to interrogate the personnel data base in order to do so. It shows how the foremen dialogue with the computer, to change the function of a miner within a team, to another team, or the function of a team as a whole. The implementation of the system, data bases, and data communication equipment and procedures, is described. The benefits obtained are presented for each level of the company: foremen and team supervisors, engineers, mine management.

Jan 1, 1977

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. 'She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943