Search Documents

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By D. C. McLean

This report summarizes the work that has been done during the past several years in adapting resins for use as auxiliaries in mine roof support. The resins were applied in two ways: 1) by injection into the strata, and 2) as a bonding agent for roof bolts and reinforcing bar. The Explosives and Mining Chemicals Department of the American Cyanamid Co. has worked during this period in cooperation with the Roof Control Research Group of the U.S. Bureau of Mines, the Pattin Manufacturing Co., the J. H. Fletcher Co., the Homestake Mining Co., the U.S. Steel Corp., the National Mines Corp. and the Pocahontas Land Corp. in an effort to create resin formulations and methods for applying them as a practical and sate type of roof support for mining areas particularly where conventional support is inadequate, yet expensive. This, work has involved much pioneering in a field where theory, speculation, and pure mythology predominates, and little basic engineering data is available. It is strange butt true that, despite the importance of roof control both from an operational and safely standpoint, there is scarcely a mining' company in this country that has an engineer, or anyone, assigned to the study of roof support problem, except temporarily--after a bad roof fall. The responsibility for improving roof control methods seems to have been placed entirely upon the shoulder, of the USBM, various State departments of mines, and individual roof bolt manufacturing; companies. It was in cooperation with the USBM that Cyanamid first developed resins for mining use.

Jan 1, 1964

By G. L. Oldright, Henry de Rycker, S. F. Ravitz

The upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the operation of sintering. A sinter feed with normal gangue constituents, containing more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead concentrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1944

By S. Harries Daddow

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway tyfanage1-s determined 011 and have long applied a test of 1000 pounds falling 101/2 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails fro; our most reliable makers, break under a G foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 138 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent. of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. I n England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariablyPILLAR of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the Common wealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

By John E. Riddell

This review is based on a questionnaire sent out in 1959 to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geo-chemical techniques in Precambrian terrains. Of the companies questioned, 21 returned completed questionnaires and of these, 15 companies stated that they had some experience in this type of work. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only three have reported that they do not use applied geochemistry at all. The others have reported that they make use of applied geochemistry in New Brunswick and in the Cordillera in areas of light glaciation. Their opinion is that it is a useful aid when accompanied by other techniques in evaluating mineralized areas. GEOCHEMICAL SURVEYS Table I reviews the type of geochemical surveys used by these companies, and the following points of interest should be noted.

Jan 11, 1960

Executive SIDNEY J. JENNINGS, Chairman. GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 6, 1918

WILLIAM L SAUNDERS, President GEORGE H PEGRAM, 1st Vice-president ALFRED D FLINN, Secretary J V W REYNDERS, 2d Vice-president JACOBS LANGTHORN, Treasurer HENRY A LARDNER Assistant treasurer Finance Committee House Committee GEORGE H PEGRAM, Chairman ; ALFRED D FLINN. Chairman J VIPOND DAVIES FREDERICK F SHARPLESS BANCROFT GHERARDI JOHN H DUNLAP WILLIAM L SAUNDERS CALVIN W RICE W F M GOSS, ex-officio F L HUTCHINSON

Jan 1, 1923

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.' At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir's work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.' Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By Ralph Arnold

Since 1915, when Elk Basin field was brought in, eight oil fields have been developed in Montana and the production has arisen from 50,000 bbl. in 1916 to 8,000,000 bbl. in 1926. The production for 1927 was 5,121,600 bbl. and the total up to the end of 1927 was 27,138,239 barrels. The eight fields, with their year of discovery are: Elk Basin, Carbon County (1915); Devil's Basin, Petroleum County (1919); Cat Creek, Petroleum County (1920); Soap Creek, Big Horn County (1921); Kevin-Sunburst, Toole County (1922); Lake Basin, Stillwater County (1924); Pondera, Pondera and Teton counties (1927); and Bannatyne, Pondera and Teton counties (1927). About 170 wildcat wells have been drilled in the state of which 8 were successful and 162 gas wells or dry. Hence, only one out of 21, or 5 per cent. of the wildcats have been successful. The average depth of the wells has been 1600 ft. and the average cost $32,000 apiece. • Up to Jan. 1, 1927, a total of 1376 wells have been drilled in the producing oil and gas fields of the state, of which 904, or 66 per cent., were successful oil wells; 82, or 6 per cent. were gas; and 390, or 28 per cent, were dry. The percentage of dry wells is excessive as compared to the wells in other states, due to the uncertainties of limestone reservoir rocks. The total production of oil to Jan. 1, 1927, has been 22,016,639 bbl. and of gas 7,265,330,000 cu. ft. The average price at the well for the oil has been $1.47 per bbl. and for gas about 4 c. per 1000 cu. ft. The value at the point of consumption has been about 23 c. per 1000 cu. ft. The total revenue derived from crude oil has been $32,277,119, and from gas 8350,613, or a total income to the producer of $32,727,832. Each well drilled in the state has already (to Jan. 1, 1927) averaged a return of over $21,000. The total number of domestic (Montana) oil and gas companies organized, since the first in 1885, has been 844, of which 702 are still alive and 142 dead. Oil and gas companies registered for operation within the state to Jan. 1, 1927, but with outside charters, are 143, of which 66 are alive and 77 are dead. Outside the few distributing companies, which are included in these figures, the grand total of 997 companies which have

Jan 1, 1928

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The initiation of localized cracking in hydrogenated high strength steel was dependent on the developmeni of a critical hydrogen conceniration and relatively insensitive to the magnitude of the applied stress. The stress was believed to influence the deluyed failure process by providing the means for grouping the hydrogen. On the basis of an assumed distribution law the observed changes in the lower critical stress as a function of notch acuity, yield strength, and temperature were predictable over a significant range of these variables. THE phenomenological characteristics of delayed failure in high-strength steel have been comprehensively investigated and the behavior has been attributed to the strong embrittling action of hydrogen.1-3 Delayed failure or, as it is also termed, static fatigue, is the most sensitive means of detecting hydrogen embrittlement since it allows the maximum time for hydrogen diffusion during a test.3 The nature of delayed failure cail be aptly described by four parameters which are schematically depicted in Fig. 1. The upper critical stress corresponds to the rupture stress in a conventional notch tensile test. The lower critical stress or static fatigue limit is the stress below which no delayed failure will occur. The incubation period is the time required for the formation of the first crack and the fourth parameter is the failure time. An increase in hydrogen content, notch acuity, or strength level of the material increases the susceptibility for delayed failure by decreasing the lower critical stress, the incubation period, and the time to failure.lY3 A decrease in test temperature prolongs the incubation period in accordance with the lower diffusion rate of hydrogen, and also de-

Jan 1, 1961

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By D. Swan

Industrial research may be defined as a critical and exhaustive investigation to create new and better ways of doing things. The results of industrial research are new and improved products, processes, and techniques. This broad definition, of course, covers investigation of all subjects by either individuals or groups of people, and this chapter aims to examine the purpose (what research tries to do), and methods (or how research is done) as applied in the mineral industries. Concepts and History The idea or concept of organized research probably originated in the universities of Europe. There, groups of scholars banded together for discussion and application of their particular specialty to a common problem. Publication of the conclusions drawn from such investigations gave scholars in other areas the opportunity to review and criticize the work of their colleagues, and one of the hallmarks of scientific research work is the publication and criticism of the results of the investigation. It was not until the late nineteenth century that the concept of organized research for the profit of industry was recognized. During the late nineteenth and early twentieth centuries, a large number of industrial enterprises sponsored organizations to study the application of the physical sciences with the aim of making discoveries that would result in profit to the sponsoring organization. The tangible benefits accruing from these activities were so great that they, in turn, fostered several other methods for the support of organized research activities. For the large problems involving public interest, United States Government scientific re- search laboratories were set up. As the demand of smaller enterprises for research activities increased, research institutes and consulting laboratories were organized. In Europe the idea of common industry sponsorship of research centers grew and many large research organizations there were sponsored by associations of manufacturers. Finally, in the United States

Jan 1, 1959

By William Glenn

In their account of chromium, Roscoe and Schorlemmer (Treatise on Chemistry, London, 1879) state that "In 1762 Lehmann, in a letter to Buffon, de nova minerœ plumbi specie crystalline rubra, described a new mineral from Siberia, now termed crocoisite." In 1786 Lehmann analyzed it (Nicholson's Jour., Dee., 1798) and found that it contained chiefly lead, and that the " mineralizers " were arsenic and sulphur. It was next examined in 1189 by Macquart and Vauquelin, who stated that it contained an intimate mixture of iron, alumina, and lead peroxide. The account of their work was published over the name of Macquart. Vauquelin (Louis-Nicolas) was a Norman peasant, who had studied in the village school, and at the age of fourteen was a laboratory-boy in a pharmacy at Rouen. Later, he found his way to Paris, and in 1789 was assistant to Fourcroy, a pharmacist and a teacher of note. It was here that he met Macquart, with whom he did the work on Siberian red lead, and at this time his friend Cheradame taught him his Latin.

Jan 1, 1896

By Fred L. Morritz, Harold M. Manasevit, Richard Nolder, Arnold Miller

Experimental evidence is presented which confirnis the epitaxial relationship between the deposited silicon and the sapphire substrate. Four distinct modes of orientation relationships have been established. These have been shown to be Single-crystal gvowth retention as a function of surfaces oriented off ideal has been qualitatively indicated. Both full-circle goniometer X-ray techniques and replica electron microscopy have indicated varying amounts of microtwinning in the silicon. film, which may he caused by the mode of silicon formation. Parameters have been found where twin density is less than I pct. The early stages of' epitaxy of silicon m sapphire have been examined by electron-microscope techniques... and mechanisms have been proposed. THE first report of the deposition of single-crystal silicon on sapphire (single-crystal aluminum oxide) was made at the American Physical Society Meeting in Canada' by one of us and was subsequently published in the Journal of Applied physics.* This paper summarizes some of the work carried on in this area since that time, in addition to reviewing some of our earlier observations. The initial single-crystal deposits of silicon on sapphire reported were obtained on sapphire planes produced by cutting a sapphire rod perpendicular to its fastest growth direction, which is approximately 60 deg from the C axis. Direct correlations between the microstructure and X-ray data as to the single crystallinity as shown in Fig. 1 are evident. These deposits were identified as (111) silicon on the substrate oriented near the (1123) of sapphire. (Sapphire notations are designated according to the c over a ratio of 2.73.) It became evident that substrate quality and surface play an important part in successful epitaxy. For example, in Fig. 2 we observe an interesting

Jan 1, 1965

By John D. Roach

DURING an investigation of the yttrium-hydrogen system aimed at producing solid yttrium hydride specimens containing various amounts of hydrogen, it was observed that yttrium containing approximately 2 wt pct H exhibited a tendency to crack and crumble to a powder on standing in air at room temperature. It was also observed that longer hydriding times, at a given temperature, increased this susceptibility to powdering without an increase in hydrogen content, also that moisture in the air is necessary for the observed effects to occur. Even if cracking did not occur, there was a continual formation of a light gray powder on the as-treated surface of the hydrided yttrium and this reaction continues until the entire hydrided piece has been reduced to a powder. Storing the hydrided specimens in the absence of air or removing the surface either by machining or grinding were effective means of preventing this disintegration of hydrided yttrium. In an attempt to determine the reason for this powdering phenomenon, the surfaces of a number of as-hydrided yttrium specimens were examined by X-ray techniques. In all cases the X-ray pattern obtained showed the major phase to be yttrium hydride (YH2) as would be expected since the specimens contained 2 to 2.2 wt pct H. In some cases a trace of yttrium oxide was observed. There was also a third phase present on the surface of these hydrided specimens which could not immediately be identified. This unknown phase was a face-centered cubic material, NaC1-type structure, with a lattice parameter of 4.855 and a calculated density of 5.914 g per cc. Very slight hand polishing of the surface of the hydrided yttrium specimens completely removed both the unknown phase and the traces of oxide so that only the yttrium hydride pattern remained. Based on the X-ray patterns the quantity of the unknown phase on the surface of the hydrided yttrium appeared to be directly related to the susceptibility of the material to powdering. Work at the Denver Research Institute on the yttrium-nitrogen binary system showed that yttrium nitride (YN) is a face-centered cubic material with a lattice parameter of 4.878A and a density of 5.890 g per cc. They also noted that this compound rapidly disintegrated to a powder on standing in air. The unknown pattern observed in the above specimens corresponds very closely to that of the nitride—fcc structure, 4.885 parameter, and density of 5.914 g per cc. The presence of this thin film of nitride on the surface of the hydrided specimens probably accounts for the observed powder formation and crumbling. The nitride reacts with the water vapor in the air (verified by private communication from Dr. C. Huffine, General Electric Co.) to yield yttrium oxide and ammonia. Ammonia is readily detected when hydrided yttrium specimens were allowed to stand in bottled moist air. The powder formed on the surface of the hydrided specimens was shown by X-ray analysis to be yttrium oxide. This reaction appears to occur primarily at the grain boundaries since discrete particles of yttrium hydride separate from the specimens during this powdering process. The reaction of yttrium nitride with water vapor is believed to be as follows: 2YN + 3H2O - Y203 + 2NH3. Despite the fact that this nitride is present only as an extremely thin surface film, if the above reaction is not prevented by removing this film from the surface either by machining or grinding, the reaction continues until the entire hydrided piece has been reduced to a powder. To account for this continuation of the reaction, it is believed that the following reactionalsooccurs: 2YH2 + 2NH3 -2YN + 5H2. The nitride produced by the latter reaction reacts in turn with water vapor. The reaction therefore becomes autocatalytic and continues until the hydride has been consumed and the entire piece reduced to oxide powder. The amount of nitride required to initiate this reaction is quite small and this nitrogen contamination can occur from a number of sources—hydrogen gas employed, minute leak in the hydriding apparatus or even from degassing of the reaction vessel itself. Longer hydriding times increase the possibility of nitrogen contamination and this is especially true when a dynamic gas system is employed in the hydriding process. The production of stable, solid hydrided yttrium is dependent on the complete absence of nitrogen contamination during processing. If such contamination does occur, powdering of the hydrided product can be prevented by removing the nitride from the surface e.g. grinding or by preventing access of air to the pieces e.g. sealing in wax or plastic. The author wishes to express his appreciation to General Electric Co. for sponsoring this research and for permission to publish the results of work under Subcontract AT-93.

Jan 1, 1962

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935