Search Documents

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By L. D. Ricketts

Discussion of the paper of L. D. RICKETTS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 711 to 737. FREDERICK LAIST, Anaconda, Mont.-I am going to tell you of some of the results we have been getting in Anaconda during the past two or three months in a large plant which was finished in May. We commenced work in Anaconda a year and a half ago on the construction of a leaching plant which was to have a capacity of 2,000 tons per day. The plant was to treat tailings from the concentrator, containing about 12 1b. of copper to the ton. During the past year we changed our plans and decided to use the flotation process on the tailings from the concentrator, which contained no oxidized copper, and apply the leaching process only to tailings which had accumulated in a large dump below the works. This dump contains about 15,000,000 tons of tailings, and since some of the copper in it is oxidized, we felt that the application of the flotation process would result in the loss of too much of the oxidized copper, particularly as time went on. In starting up we had a number of difficulties to overcome, as is usually the case. They were not of a serious character. The results obtained, so far, have been decidedly encouraging. During July the plant treated a total of 50,000 tons of tailings, or an average of 1,610 tons per clay. The extraction was about 83 per cent., which, on material of the grade treated, meant a. tailing assaying under 0.1 per cent. copper. The acid consumption was about 65 lb. per ton, and the fuel percentage in. roasting was about 4 ¼ . We expect to cut the fuel percentage in the next month or two to about 3 per cent., the high percentage during July being clue to starting up and shutting clown furnaces. We find that iron builds up in the solution to a marked degree. This is not a serious platter with us, because we have cheap sulphuric acid and can reject solution whenever it gets too foul. The extraction of silver has been remarkably good in the large plant. It has averaged better than 75 per cent. It seems that so long as we maintain salt in the solution to a percentage of 10 per cent., the extraction is good. We allowed the salt to fall off in order to find how low a percentage we could use. At about 7 per cent. the silver extraction fell to 65 per cent. This was to be expected, because silver chloride is soluble in strong brine, but not in weak brine.

Jan 12, 1915

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By Ralph E. Esarey, George V. Cohee

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By George V. Cohee, Ralph E. Esarey

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By Tell Ertl, Ernest E. Burgh

The Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental Processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose—that of finding out how to mine oil shale most cheaply—entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, fattors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing, when the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. Procedure Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 141 in. in diameter was used in 6, 12, and 18 ft lengths with 1/8-in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton, During the experiments air pressure varied between 75 and go psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings TO facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-stee1 sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a I-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1949

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By D. C. Porterfield

ProUuction of crude oil in Venezuela increased from 186,134,000 bbl. in 1940 to 2~8,131,ooo bbl. in 1941, or 22.6 per cent, to establish a new all-time high for the country. While the average production for the year was 625,000 bbl. per day, production during the month of December 1941 averaged 751,000 bbl. per day, and during the last week of the year, 766,000 bbl. per day. Production from the Lake Maracaibo basin averaged 454,000 bbl. per day during the year, or 72 per cent of the total for the country, compared with 73 per cent of the total produced in 1940. Drilling during the year was approximately on the same scale as in 1940, with 438 wells completed in 1941 as compared with 429 the year before. Exploratory completions decreased from 18 in 1940 to 6 in 1941. Of the drilling operations in 1941, 56 per cent was concentrated in the Lake Maracaibo basin and 44 per cent in eastern Venezuela, success being 98 per cent in the Lake basin and 83 per cent in the east. Successful completions for the country as a whole amounted to 92 per cent of the total wells drilled. Exploratory drilling in 1941 resulted in the discovery of three new fields, all in eastern Venezuela; viz., Guara, about II km. to the northeast of the Oficina field but on a separate structure; Santa Rosa, which is east of El Roble field on a structure forming a part of the major Santa -Ana- San Joaquin-El Roble uplift; and Santa Barbara, which is southwest of the Jusepin field on an extension of the main Jusepin anticline. At the close of the year three wildcats were drilling, all of which showed prospects of obtaining production; that is, Mercedes No, 2 in central Guarico, Las Ollas No. I on the Anzoategui-Guarico border near the town of Zaraza, and Quiamare No. I in Anzoategui northeast of the town of San Mateo. In spite of heavy withdrawals and the resultant natural decline in the potentials of older producing areas, new drilling during the year increased the potential production of the country from an estimated 780,000 bbl. per day at the end of 1940 to an estimated 810,000 bbl. per day at the end of 1941, or approximately 4 per cent. Since domestic consumption of petroleum products is insignificant compared with total production, exports of crude and products during the year increased in line with production. Crude exports totaled 196,800,000 bbl., compared with 158,400,-000 bbl. in 1940, and exports of products were 26,100,000 bbl., compared with 21,900,000 bbl. the year before. Exports of crude from Venezuela to the United States amounted to 36,500,000 bbl. In addition, about 2,200,000 bbl. was imported in bond into the United States for transfer to Canada. Total refining capacity of the country in 1941 was approximately 125,000 bbl. per day, including a crude-conversion plant with a capacity of 32,000 bbl. per day, capable of making fuel oil only. Three plants with a capacity of 121,000 bbl. Per

Jan 1, 1945

By K. L. Young

The general energy equation, including change in kinetic energy, was solved by numerical integration and used to evaluate simplifying assumptions and application practices over a wide range of conditions. When extreme conditions were encountered, sizable errors were caused by large integration intervals, application of Simpson's rule and neglecting change in kinetic energy. A maximum error of only 1.31 percent was caused by assuming temperature and compressibility constants at their average value. It was discovered that a discontinuity can develop in the integral for the injection case. This discontinuity indicates a point of zero pressure change and is an inflection point in the pressure traverse. INTRODUCTION When a pressure in a gas well is to be calculated, one of the first decisions is to select a method of calculation. In many instances, this selection becomes a problem because the literature, at best, provides an evaluation of any method for only a limited range of conditions. Once a method has been selected, a question often arises as to the size of the calculation interval which should be used. The question regarding calculation interval arises because an analytic solution is not obtainable and approximate solutions must be used. This paper presents an evaluation of major assumptions and application practices of probably the two most widely used methods for calculating steady-state single-phase gas well pressures. The two methods are Cullender and Smith1-" (numerical integration), and average temperature and com-pressibility. The Cullender-Smith method assumes that change in kinetic energy is negligible and is normally applied in two steps with a Simpson's rule correcton. The average temperature and compressibility method, in addition to neglecting kinetic energy change, asumes that temperature and compressibility are constant at their average values. This method is normally applied for wellhead shut-in pressures of less than 2,000 psi, and in one step. Computer programs were written to compute bottom-hole pressure with and without the assumptions, using various approaches. Values of input parameters investigated are shown in Table 1. Flow rate was limited to a maximum of 5,000 and 10,000 Mcf/D for tubing sizes of 1.610 and 1.995 in. ID, respectively. Flow rate was also limited to 10,000 Mcf/D for a tubing size of 2.441 in. ID when wellhead flowing pressure was 100 psia. These limitations were imposed on flow rate so as not to exceed sonic velocity. The z factor routine available necessitated limiting bottom-hole temperature to 240F and wellhead pressure to 3,000 psia. Pressures were compared on the basis of percent deviation from the trapezoidal integration of Eq. l or 2 at 100-ft intervals. A preliminary investigation indicated that a 1,000-ft interval solution would differ from a 50-ft interval solution by less than 0.25 percent; therefore, the 100-ft interval was chosen for a base. For the purpose of comparison, deviations less than 1 percent were considered insignificant. where 111.1 qeC2/d p = kinetic energy term. Eqs. 1 and 2 can be evaluated numerically at specific depths using the trapezoidal rule as shown by Cullender and Smith. If change in kinetic energy is neglected and temperature and compressibility are assumed constant at their average values, Eq. 1 can be integrated to give the average temperature and compressibility equation,

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?', phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?' layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By Charles W. Carter, Alfred H. Bell

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Alfred H. Bell, Charles W. Carter

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Robert L. Frantz

Progress and improvement continue to be the bywords of a dynamic coal industry. The industry continues to gain strength and expand its horizons in the face of competition from atomic energy and the problems of restrictive legislation. The direct contribution of coal mining and transportation to the national economy is about $3 billion a year ac- cording to a study made by the National Coal Policy conference. Coal remains the backbone of the power industry producing almost two-thirds of all the electrical energy generated by fossil fuels and one-quarter of all the energy consumed in the nation. Power supplied by electric utilities increased 6.9% last year. The chairman of the Federal Power Commission predicted a 7.5% growth rate until 1980 for the nation's electric output. Some 80,500 MW of fossil fired power plant capacity are on order or under construction before 1974, compared to a present capacity, all sources, of about 290,000 MW. The comparable new additions of nuclear power plants is expected to total about 51,000 MW.

Jan 2, 1969

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933