Search Documents

By J. D. Defilippi, E. M. Gilbert, K. G. Brickner

FCC chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Transformation to martensite is considered to be responsible for this behavior in some metastable Cr-Mn-N steels. However, very stable Cr-Mn-N steels also exhibit a ductile-to-brittle transition. The results of this study indicate that deformation faulting is the probable cause of the brittle behavior of stable Cr-Mn-N steels. Deformation faulting accounts for the ductile behavior of these steels in a tension test at -320°F and brittle behavior in an impact test at -320°F. Deformation faulting also accounts for the toPological features observed on the fracture surfaces of impact specimens of these steels. FACE- centered- cubic chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Many Cr-Mn-N steels transform to martensite during deformation,l-5 and several investigatorsl-3 have suggested that the brittle behavior of these steels is caused by martensite formation. However, very stable Cr-Mn-N steels also exhibit brittle behavior. Schaller and Zackeyl reported that a very stable Cr-Mn-N steel (less than 3 pct martensite formed at -320°F) exhibited a transition temperature higher than that for steels in which large volume fractions of martensite formed during testing. The explanation given by Schaller and Zackey for this observation was that in the very stable steel the martensite, because of its higher interstitial content, was more brittle than that formed in their other steels. This explanation was questioned by Tisinai and samans4 and Baldwin.6 Moreover, because the toughness of stainless martensite at cryogenic temperatures is generally very low, this explanation does not account for Thompson's7 observation that small additions of nickel (1 to 3 pct) greatly improve the toughness of high nitrogen (0.35 pct) Cr-Mn-N steels. The present paper summarizes the results of an investigation of the low-temperature brittleness in very stable Cr-Mn-N steels. The importance of the mode of deformation on the toughness of these steels is discussed. Table I. Compositions of the Steels Invertigated, Pet Steel C Mn P S Si Ni Cr N - A 0.09 14.70 0.018 0.011 0.47 0.22 18.40 0.54 B 0.12 14.90 0.001 0.008 0.48 0.14 17.80 0.38 C 0.12 14.95 0.004 0.005 0.62 3.95 18.43 0.38 MATERIALS AND EXPERIMENTAL WORK The compositions of the steels investigated are shown in Table I. Steels A and B had compositions within the limits of a proprietary Cr-Mn-N stainless steel,* whereas Steel C was similar in composition to the proprietary steel except for its 3.95 pct Ni content. All steels were hot-rolled to 1/2-in. thick plate. The plates were subsequently annealed for 1 hr at 2000°F and water-quenched. Standard longitudinal and transverse Charpy V-notch impact specimens were machined from the annealed plates. Duplicate longitudinal and transverse impact specimens were tested at 212", 80°, 32", 0°, -100°,-160°,-200°,-256", and -320°F. Longitudinal tension-test specimens were also machined from the plates and tested at a crosshead speed of 0.05 in. per min at the aforementioned temperatures. The fractured impact and tension-test specimens of all three steels were examined to determine whether martensite had formed during testing. Magnetic, X-ray, electron-diffraction, and electron-microscopy techniques were used to detect the presence of martensite in the highly deformed areas of these specimens. Metallographic examination of highly deformed areas of impact and tension-test specimens revealed the presence of dark-etching bands, such as those shown in Fig. 1. These bands were observed only in deformed samples and were thought to be associated with the low-temperature brittleness of the Cr-Mn-N steels. Accordingly, a sample 1 in. wide by 3 in. long was cut from the 1/2-in.-thick plate of Steel C. This sample was surface-ground to a in. and then cold-rolled 60 pct at -320°F. Thin foils were prepared from the cold-rolled sample and examined in a JEM electron microscope. Brightfield, dark-field, and selected-area diffraction techniques were used to determine the cause of the dark-etching bands. Fractographic experiments were also performed. Impact specimens Of Steels A, B, and C were broken at -320oF, and the fracture surfaces of these specimens were immediately shadowed with carbon. The carbon replicas were examined in a Siemens electron microscope, and attempts were made to correlate the topological features of the fracture surfaces with the deformation mechanisms that could be occurring during an impact test of these steels.

Jan 1, 1970

By Donald B. Gillies

PROBABLY the most critical and difficult period in an engineer's career is that between the completion of his college work and his attainment of professional recognition and accepted status in the industrial world. Upon leaving school the young graduate breaks his immediate ties with his educational institution and in a sense finds himself adrift. At this time in his life a society like our Institute has both the responsibility and the privilege of meeting a vitally important need in his professional life. Some of these young men are Student Associates, in the year after graduation, and some are Junior Members, but all need advice and assistance. In some respects this situation will be accentuated by the war. Not only will thousands of young engineers be mustered out of military service but the process we describe generally as industrial reconversion will make necessary many readjustments in personnel. About two years ago the Institute recognized the opportunity of helping the younger member to help himself by appointing a new standing committee to be known as the Committee on Professional Development of Junior Engineers. Herbert Hoover is Honorary Chairman and it is my privilege to serve as Chairman. The name of the Committee is not entirely satisfactory but it expresses the general objective. The present article is in the nature of a progress report of the work of this Committee.

Jan 1, 1945

By J. W. Spretnak, D. A. Chatfield, G. W. Powell, J. R. Eifert

In nzost cases, the driving force for a lattice transformation is produced by supercooling below the equilibriunz transformation temperature. The interfnce reaction in isothermally annealed, multiphase diffusion couples may involve a luttice transformation which also requires a driving force. Direct experinzental evidence has been obtained for the existence of the driring force in the form of a supersaturated phase at the aocc)-0@cc) interface in Cu:Cu-12.5 ult pct A1 couples; the super saturation is equivalent to an excess free energy of approximately 3 cal per mol at 905. A tentatiue interpretation of the dynanzic situation a1 the interface based on the free energy-composition diagram is proposed. THE presently accepted theory of diffusion in multiphase couples1 states that there will be a phase layer in the diffusion zone for every region which has three degrees of freedom and which is crossed by the diffusion path in the equilibrium phase diagram. For binary systems, this restriction excludes all but single-phase fields and, for ternary systems, only one- and two-phase fields are included. In addition, Rhines"~ as well as other investigators3 6 have reported that the compositions of the various phases adjacent to the interfaces are, for all practical purposes, the compositions given by the intersections of the diffusion path with the solubility limits of the single-phase fields of the equilibrium phase diagram. Some studies of the rate of thickening of these intermediate diffusion layers indicate that the thickness of the layer changes para-bolically with time, or: where x is the position of the interface relative to an origin xo, t is the diffusion time, and k is a temperature-dependent factor. crank7 shows mathematically that, if the compositions at an interface are independent of time and the motion of the interface is controlled by the diffusion of the elements to and from the interface, then the segments of the concentration penetration curve for a semi-infinite step-function couple will be described by an equation of the form: hence, Eq. [l] follows from Eq. (21 if the interface compositions are fixed and if the motion of the interface is diffusion-controlled. Although the concept of local equilibrium being attained at interfaces has assumed a prominent role in the theory of diffusion in multiphase couples, experimental evidence and theoretical discussions which challenge the general validity of this concept have been reported in the literature. arkeen' has stated that strict obedience to the conditions set by the equilibrium phase diagram cannot be expected in any system in which diffusion is occurring because diffusion takes place only in the presence of an activity gradient. Darken also noted that it is usually assumed that equilibrium is attained locally at the interface although the system as a whole is not at equilibrium, the implication being that the transformation at the interface is rapid in comparison with the rate of supply of the elements by diffusion. ISirkaldy3 indicates agreement with Darken in that he believes the concept of local equilibrium is at best an approximation because the motion of the phase boundary requires that there be a free-energy difference and, hence, a departure from the equilibrium composition at the interface. Seebold and Birks9 have stated that diffusion couples cannot be in true equilibrium, but the results obtained are often in good agreement with the phase diagram. The initial deviation from equilibrium in a diffusion couple will be quite large because alloys of significantly different compositions are usually joined together. Kirkaldy feels that the transition time for the attainment of constant interface compositions (essentially the equilibrium values) will be small, although in some cases finite. Castleman and sieglelo observed such transition times in multiphase A1-Ni couples, but at low annealing temperatures these times were quite long. Similarly, ~asing" found departures, which persisted for more than 20 hr, at phase interfaces in Au-Ni and Fe-Mo diffusion couples. Braun and Powell's12 measurements of the solubility limits of the intermediate phases in the Au-In system as determined by microprobe analysis of diffusion couples do not agree with the limits reported by Hiscocks and Hume-Rothery13 who used equilibrated samples. Finally, Borovskii and ~archukova'~ have stated that the determination of the solubility limits of phase diagrams using high-resolution micro-analyzer measurements at the interfaces of multiphase couples is not an accurate technique because of deviations from the equilibrium compositions at a moving interface; diffusion couples may be used to map out the phase boundaries in the equilibrium diagram, but the final determination of the solubility iimits should be made with equilibrated samples. The purpose of this work was to investigate the conditions prevailing at an interface in a multiphase diffusion couple and to compare the interface compositions with those associated with true thermodynamic equilibrium between the two phases. Microanalyzer techniques were used to measure interface compositions in two-phase Cu-A1 diffusion couples annealed at 80@, 905", and 1000°C for various times.

Jan 1, 1969

By M. W. BERNEWITZ

DURING my recent extended visit to Australia and New Zealand, these notes on oil and gas prospecting in that part of the world were compiled from recent reports-press and government, from conversation with one of the financial leaders in the search for oil, and from personal observation of operations of the principal importers, blenders, and distributors of oil products; also from the astonishing testimony given by them to the Petrol Commission. Australia and New Zealand have practically no petroleum production beyond a few thousand gallons a year from wells in the latter Dominion. Everything is imported, Table 1. showing the quantities for 1929-30 in Australia and for 1930 in New Zealand,

Jan 1, 1934

Illustrated guidebooks treating in a popular descriptive way of the geology and other features of the Western United States have been issued by the U. S. Geological Survey. They will be of much interest to mem¬bers in connection with the Arizona Meeting of the Institute and espe¬cially the guidebook of the Santa Fe Route, with side trips to the Grand Canyon, containing as it does relief maps, topographical and geological maps, covering the entire route of the railroad, illustrations from photo¬graphs and other interesting descriptions of this great country. The method of treatment is adapted to the lay-reader, although it includes much valuable and interesting technical information concerning the geographical and other features. The books are well indexed. These volumes sell for 50 c. each and may be obtained from the Superintendent of Documents, Washington, D. C. These guidebooks originally sold for $1 each, but the reprint edition has been reduced to 50 c. A list of the different guidebooks follows: Bulletin 611. Guidebook of the Western United States, Part A, The Northern Pacific Route, with a Side Trip to Yellowstone Park, by M. R. Campbell, and others. 1915. 212 pages, 27 route maps, 27 plates, 39 text figures.

Jan 6, 1916

By W. B. Mather

R. G. Wuerker (University of Illinois, Urbana)—Mr. Mather is to be congratulated for stressing the most urgent need for a program of testing the physical properties of rocks, as they are encountered by the petroleum engineers on their drilling jobs and by the miners on their excavating, roof control and mineral preparation tasks. Another valuable source of information is the Handbook of Physical Constants.22 It stresses the physicist's approach rather than the engineer's procedure. The study of hardness, and rock hardness in particular, is beset with many difficulties. There is no satisfactory definition of hardness yet, and the term hardness is used to describe a number of quite dif- ferent properties. Hardness tests are grouped into static and dynamic determinations. They should be expressed with reference to the mechanical action of the applied force, like indentation hardness, scratch hardness, abrasion hardness, rebound hardness. A discussion of all these various hardness tests and of the special difficulties encountered in hardness testing of such heterogeneous material as rocks is given in the U. S. Bureau of Mines' standard proposal. The more critical student may be referred to the book by D. Landau: Hardness, which is in my opinion the best existing treatise on this subject.

Jan 1, 1952

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By Akio Suzuki, P. G. Wahlbeck

AS a part of a study of the vaporization of transition metal-chalcogen systems, the vaporization reactions for the Ti-Se system have been studied. In order to establish vaporization reactions it is important to determine the identity of vapor species in equilibrium with the condensed phases. In some cases, it is possible to deduce the identity of vapor species through observations of composition change of the condensed phase with which the vapor is in equilibrium. Determination of vapor species in equilibrium with condensed phases should precede vapor-pressure measurements and is necessary for proper thermodynamic analysis of vapor-pressure data. Bear and McTag-gart' reported that vacuum heating ot TiSea at 950°C produced a residue with a composition of 1.7 Se/Ti atomic ratio units. Analyses of condensed phases existing for the Ti-Se system have been performed by Bernusset,2"4 Gron-vold and Langmyhr,5 Hahn and Ness,' and Ehrlich.~ Results and conclusions of two types of experiments are described herein: 1) experiments where samples of known composition were vaporized followed by chemical analysis of residues and 2) experiments where the vapor species were identified by means of a mass spectrometer. Experimental Section. Sarnple Preparation. Samples of TiSe2 were prepared in a sealed, evacuated quartz ampule by heating to 1000°C stoichiometric amounts of selenium of 99.999+ pct purity obtained from the American Smelting and Refining Co. and titanium of 99.2 pct purity obtained from A. D. Mackay, Inc. After heating, the sample was ground and reheated to insure homogeneity. Samples containing less selenium than TiSez were prepared by mixing amounts of titanium powder and TiSez appropriate for the desired composition; the titanium and TiSez mixture was heated in the same manner as described for TiSe2. Analyses of titanium selenide samples contained in quartz crucibles were performed by gravimetric oxidation in oxygen at 800°C; the products of the oxidation were solid TiOz and gaseous Se02. The mass of the original sample and the mass of TiOn determined the Se/Ti atomic ratio. The sample of TiSen used in these experiments had a composition of 2.04 Se/Ti atomic ratio units. The compositions for all samples reported were analyzed by this method. Va/!orization Experiments. Samples of titanium selenides were vaporized in tungsten Knudsen crucibles. Some vaporization experiments were carried out in glass vacuum lines followed by chemical analyses of residues, and some vaporization experiments were performed with a Bendjx mass spectrometer as described previously.8

Jan 1, 1967

Book Review Mexico, TODAY AND Tomorrow. By E. D. Trowbridge, Detroit. The McMillan Co., New York, 1919, 353 pp., 7;2 X 5 in. $2.00. The first eight chapters are devoted to an historical narrative of the Mexican peoples from the earliest times to the close of the war with the United States in 1345. "In dealing with events antedating what may be termed modern Mexico" the author has "made no attempt at original research, and so far as concerns anything prior to 1900, the work here presented is a repetition, a reflection, of the findings of opinions of Fiske, Prescott, Bancroft, Luis Perez Verdia and other authorities." The remainder of the hook deals with Mexico during and since the Diaz regime. It is interesting throughout but is not always convincing or consistent. Social conditions are described in a way illuminating and possible only to one who is familiar with the peon and his hitherto seemingly hopeless position in reference to the wage system and church oppression. In fact, the author makes the hold accusation that the "primitive rather than immoral" condition of the peons in the matter of their marital relations is due to the disregard of the church for their welfare and capabilities. The true accounts of the Madero revolution and the Huerta regime read like fascinating medieval fiction. The reason given for men remaining in the Madero army is still the controlling one regarding any of the armies there. "They had horses, arms, all the food they wanted, money to spend and no work." The discussion of Mexican financial schemes is wholly from the Carranza viewpoint. To meet a monthly deficit of ten million pesos the author says "the government forced loans from the National Bank, and Bank of London and Mexico, and repeated the operation several times, finally practically exhausting their bullion and cash reserves. Hostile foreigners refer to this operation as the looting of the hanks! Drastic as this action was, there was good ground on which to justify it." However, that necessity knows no law is never an acceptable tenet except to him who applies the screws. The discussion of the economic problems and their solution is rather chimerical and presupposes a civil and national virtue in the present government not discernible except to one ultra friendly. The book is an interesting exposition of the very much involved situation from the viewpoint of approval of both the Carranza government and the attitude of the United States in its dealings with him. The editing of the book leaves something to he desired. P. E. B.

Jan 9, 1919

By A. H. Geisler, J. H. Keeler

Preferred orientations in rolled and annealed titanium sheets were determined by the Geiger counter spectrometer X-ray diffraction technique. Five annealing textures dependent upon the temperature range of annealing were found, and in order of increasing annealing temperature pendent upon the temperature range are: 1—a deformation like texture, 2—a rotated inorder a-recrystallization temperature texture, 3-a retained u-recrysraIlization texture, on annealing at lower temperatures of the ß-region, 4—a transformation texture based on recrystallized a and predicted by the Burgers' relationship, and 5—a ,ß-cube texture. These results are examined in terms of current theories of recrystallization textures. UMEROUS investigators have described the tex- ture obtained by cold rolling the hexagonal metals, titanium, zirconium, and beryllium, which have c/a ratios less than that of ideal packing, 1.633. The basal planes are rotated out of the rolling plane, about the rolling direction, so that the basal poles are tilted toward the transverse direction as shown schematically in Fig. la. In all instances but one,' it was also reported that the [1010] direction was parallel to the rolling direction (see Fig. lb). Hot rolling has been reported as causing a similar tilt of the basal poles in the transverse direction (see Fig. la) and causing the [1010] direction also to be parallel to the rolling direction as shown schematically in Fig. lb. Annealing after deformation does not appreciably change the tilt of the basal poles in the transverse direction." Beryllium2-7 continues to have the [1010] direction in the rolling direction after annealing, and similar observations for titanium and zirconium' . have been reported for annealing at fairly low temperatures, again as in Fig. lb. At higher annealing temperatures, however, the recrystallized grains of titanium" and zirconium have an orientation such that the [1120] direction is approximately in the rolling direction, although the basal poles are still inclined in the transverse direction. Figs. la and lc show the resulting orientations schematically. This change in orientation has been described as a nominally ±30° rotation of the hexagonal crystallites about the basal poles of the cold rolled texture and is apparent from the results which are summarized in Table I for investigations with the X-ray diffraction technique employing film. The angles y, , and ß are indicated in Fig. 2 which represents the stereographic projection of (1070) poles for the mean orientation of a pole figure. Texture determinations for titanium using the Geiger counter spectrometer have provided similar results except that in some instances additional components of the texture were proposed, as shown by the summary of data in the upper half of Table 11. On the other hand, the spectrometer technique, when applied to zirconium,* has revealed a splitting Recently completed studies of the textures of annealed zirconium", show zirconium to possess textures very similar to those reported here for titanium. Therefore, much of this discussion will include zirconium by virtue of its close similarity to titanium in pref erred orientations. of the intense areas of the pole figure for samples annealed at 600°C. This splitting could be described by a 7" rotation of the tilt axis about the normal to the rolling plane. Such a splitting for the annealed texture relative to the cold rolled texture was not observed in other determinations for either zirconium or titanium using the less sensitive film X-ray methoe and makes the relationship between the two types of texture more complex than the simple rotation about the (0001) pole based on film work. The more precise investigations on zirconium permit the descriptions in the lower part of Table 11, which show that the texture depends quantitatively on the temperature of annealing. When zirconium is annealed at temperatures up to 400°C, the texture is similar to the cold rolled texture, while annealing in the range 500" to 900°C produces a texture which is only approximately described as [11%] in the rolling direction. More precisely described results for zirconium show that the two types of splitting ( 1—about an axis in the rolling plane through an angle given in the second column in Table II and 2—about the normal to the rolling plane through an angle given in the third column of Table 11) depend on annealing temperature. The [1120 is the rolling direction only when the annealing temperature is in the vicinity of 900°C

Jan 1, 1957

By C. A. Stetefeldt

IK the dry-crushing of ores, either by stamps, rolls, or other machinery, it is essential that the material should be free from moisture. Hence a contrivance which effects this with economy, and is of durable and compact construction, is a great desideratum. It is claimed for the below-described shelf dry-kiln, that it possesses these qualifications in a high degree. The construction of the shelf dry-kiln is based on the Hasenclever principle. That is to say, a number of inclined shelves are arranged zig-zag above each other in a vertical shaft, having openings or slits where they meet, on which the ore rests in a stratum, the thickness of which is governed by the width of the slits and the inclination of the shelves. If a portion of the charge is removed at the end of the bottom shelf, a sliding motion of the ore takes place on all shelves above, and the top shelf is replenished from a hopper set over it. It will be seen that the shaft is divided by the shelves into a number of triangular prismatic spaces. Through these the hot gases from a fireplace are made to circulate, each space communicating with the next one by a flue arranged in the sidewall of the shaft. These flues being located on alternate sides of the shaft, a continuous passage is formed through the whole structure. After thus stating the principle of the construction, its details will be easily understood by reference to the drawings, Fig. 1 to Fig. 5. The drawings, Fig. 1 to Fig. 4, represent two kilns united into one structure. The cast iron shelves(a) are 2 feet 4 inches wide and 5 feet long, with sides and a back 4 inches high, and are cast a full halfinch thick. How they rest on the brackets(d), and interlock each other, is shown in Fig. 5. Three such shelves, with an inclination of 38') are placed in one row in a brick shaft 7 feet 1/2 inch wide and 4 feet deep. The ore hoppers(g) rest on the iron bems(f). At the end of the bottom shelves are the discharge-doors(b), with shoots projecting beyond the front wall. A swinging apron(e) keeps the ore in place. By dropping it a car below the shoot is filled with dry ore. A number of extra-large pieces of ore may cause a stoppage in the slits ; for such an emergency the openings(e) are provided, through

Jan 1, 1884

By Oliver Ralston

DURING experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent, zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 lb. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: PER CENT. PER CENT. Oz. PER TON Cu 0.695 A1203 0.83 Ag 1.30 Zn 6.17 S...:: 43.35 Au 0.02 Fe 36.23 CaO 0.46 Si02 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: PER CENT. PER CENT. Chalcopyrite 2.0 Schist 3.2 Marmatite 10.32 Quartz 8.2 Pyrite 73.0 Calcite 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as. to render impossible the preparation of commercial grades of concentrate:

Jan 1, 1929

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By Robert Glass Cleland

DURING the closing month of 1929, Walter Douglas found his health impaired by the strain of many difficult years of alternating prosperity and depression, and in April 1930 resigned the presidency of Phelps Dodge. Douglas was succeeded by Louis S. Cates. The choice broke a tradition that had been held inviolate for almost a hundred years. For the first time in its long history, the direction of the company's policies and operations was entrusted to a stranger without previous Phelps Dodge background, training, experience, or tradition. But the choice was wisely made. For a time at least, the path of Phelps Dodge was to run through rough and dubious ground, and no man in the United States was better qualified to blaze that trail than Louis Cates. After graduating from the Massachusetts Institute of Technology, Cates had served a rough and financially un- profitable apprenticeship at one of the century-old mining camps of Chihuahua, Mexico. Following his return to the United States and a brief interlude as assistant to the president of the National Steel and Wire Company, he had resumed his mining career, first as timekeeper, then as

Jan 1, 1952

By H. A. Jr. Koch, C. A. Hutchinson

Miscible phase displacement of oil from reservoirs has been emphasized in the past few years. The reason for this emphasis lies in the high oil recovery attainable by this process. Removal of capillary effects in the reservoir leads to recoveries approaching 100 per cent in the area contacted by the miscible phase. The miscible slug process is one means of obtaining a miscible displacement. Here a band or slug of I,PG is injected into the reservoir prior to gas injection. The idea is to maintain the band of LPG "wedged" between the gas and oil phases and thus achieve a miscible phase displacement. A second method lor achieving miscibility is through the injection of a gas which is not miscible with the reservoir fluid but which develops a zone of miscibility in [he reservoir through mass trans-ier with the reservoir oil.' This mass transfer results in either an enrichment of the lean injected gas by intermediates from the oil or an enrichment of the oil by intermediates from a rich injection gas or one that has been enriched on the surface by LPG addition. We are interested here in discussing the process in which miscibility is developed at the displacement front by the evaporation of interrnediatcs from the oil phase into the gas phase. This process "builds up" its own slug of miscible material at the displacement front and therefore does not require the injection of LPG to obtain miscibil-ily. Each process has its own area of applicability. Generally, the high pressure gas process is applicable only with reservoir fluids which con-!ain a high concentration of inter- mediates. If the high pressure gas process is technically feasible at pressures less than 4,500 psi, it is probably more desirable economically than the slug process. The slug process has broad applicability in the shallower reservoirs and with reservoir fluids which contain a relatively low concentration of LPG and natural gasoline constituents. This paper deals with some new concepts of the high pressure gas injection process where it is proposed that flue gas can be substituted for hydrocarbon gas without sacrificing our goal of miscibility. MECHANISM Introduction Considerable effort has been devoted to study of the mechanics ot the high pressure gas injection proc-one generalization result-ing from some of these studies was that the composition of the injected gas is relatively unimportant in establishing the miscibility pressure* for a given reservoir fluid. This generalization is correct for the composition range of gases typically encountered in the field. Two such gases are a gasoline plant tail gas containing 85 per cent methane and 15 per cent ethane, and a field separator gas containing 70 per cent methane and 30 per cent heavier components. The most important factor which sets the miscibility pressure in the operation is the reservoir fluid composition, particularly the concentration of LPG-natural gasoline constituents. The injected gas is the agent by which the LPG-natural gasoline constituents are concentrated at the displacing front to create a miscible displacement. Based on these results, it appeared feasible that some inexpensive gas, such as flue gas, might be substituted for hydrocarbon gas for use in the high pressure gas process. A re-examination of the phase relations of the high pressure gas injection process should clarify the principle behind using flue gas (essentially nitrogen) as an injection gas. Three Component Diagram The phase relations of the high pressure gas injection process have been illustrated by the use of the three component diagrams.'," In Fig. 1 we have arbitrarily represented the multi-component reservoir system by three components; methane, ethane through hexane, and heptanes plus. The solid curve ABC is the phase boundary curve. It represents the locus of compositions which have fixed saturation pressure at a fixed temperature; the lower branch AB shows bubble point compositions, the upper branch BC, the dew point compositions. Point B is the coniposition of the critical mixture at this temperature and pressure. The dashed lines (tie lines) connect vapor and liquid compositions which are in equilibrium. Let us consider Reservoir Fluid D which we wish to displace in 21 miscible manner by gas injection. Let us further restrict the discussion to the case where miscibility between an injection gas and the reservoir fluid at the displacement front is developed by gas enrichment in the reservoir. For this case, any gas whose composition lies between Points C and E on the right side of the three component diagram can be used to give a miscible displacement of Reservoir Fluid D. This is true because the more mobile injected gas moves faster than the displaced oil and is in continuous contact with virgin oil at the displacement front. This leads to a continuing enrichment 01' the gas at the displacement front by evaporation of the C, - C,

By Ward C. Smith

The industry of producing and processing boron compounds is called the borax industry because the chief product is borax, the decahydrate of disodium tetraborate. For the same reason, it is common to speak of borax mining. Reference to borate mining also is common, and while appropriate where it emphasizes the diversity of borate minerals that are mined in various countries, it is rather unsatisfactory where used in a general sense, because it seems to exclude the important production of borax from brine at Searles Lake, California, and of boric acid from steam vents in Tuscany, Italy. The terms "boron industry" and "boron mining" might seem more comprehensive, but are little used, and this is fortunate because they would be misleading-the element boron is manufactured only in small amounts for special uses, and it is not found free in nature. In most occurrences, boron is combined with oxygen and is in a borate or borosilicate material. The history of the modem borax industry starts with the introduction into Europe of borax from Tibet in the 13th century, about the time of Marco Polo, if not actually by him. The discovery that borax has unique value as a flux in metal soldering and ceramic glazing must have been made at some unknown time much earlier. As a rule, any mineral that has been used so long that its early history is lost must occur in deposits that are easily recognized and worked, and this is undoubtedly true of borax in Tibet. According to meager accounts,9 the borax occurs there in arid mountain basins as surficial crusts that coat the ground about thermal springs and seeps of mineralized water, and as coarser crystals in the bottom muds of shallow pools and lakes. Much the same essential features of surface exposures and minerals easy to recognize and recover characterize most of the deposits later found and worked elsewhere. The borax industry at the present time is faced with rising demands for its products, and consequently is increasing its productive capacity and appraising its borate resources.18 The areas that contain the known borate deposits are most likely to yield additional production, hence their distribution in the world is of interest, and is summarized later in this chapter. Mineralogy The mineral raw materials used by the borax industry include various borates mined in several countries, borax extracted from brines at Searles Lake in California, and boric acid extracted from the steam of vents in Tuscany in Italy. The hydrated borates[$] of chief commercial importance are listed in Table 1, which also shows their chemical composition. The properties of only the four most important borates are summarized here, but detailed descriptions of the borates and the minerals commonly found with them can be found in mineralogy textbooks.41 Ulexite generally forms clusters of silky fibers rather than large individual crystals. A

Jan 1, 1960

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of 'InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of' metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.'-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.' This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.' A concurrent publication'0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.'' Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By E. A. Gulbransen, A. Pebler

Pressure-composition isotherms have been determinedfor the systems ZrMo2 -H2 between 0" and 900°C at hydrogen pressures between 10-4 and 760 Torr. Tkese studies plus X-ray diffraction analyses of selected compositions show that these intermetallic compounds form a complete series of hydrogen solid solutions within this temperature and pressure range. The partial molar enthalpies and entropies of solution of hydrogen in the three intermetallic compounds were calculated. The solubility of hydrogen in these Laves phases can be related to their free electron concentration. ThE reaction of hydrogen with inter metallic compounds of zirconium with Laves phase-type structure has both theoretical and practical interest. The in-termetallic compounds have structures different from any of the pure metals. In addition the electron to atom ratio of the intermetallics varies appreciably. In the nuclear materials field, these materials are of interest since intermetallic compounds may exist as precipitates in commercial zirconium alloys with transition metals. From studies on the hydrogen reaction, one can establish the stability of the intermetallic compounds relative to the hydrides of the component metals. The intermetallic compounds may also be used as getters for hydrogen and as materials for hydrogen storage. This paper will present the results of equilibrium and structural investigations of the ZrCr2-H2, the ZrV2-H2, and the ZrMo2-H2 systems for the temperature range of 0" to 900°C and the pressure range of Torr to 1 atm. A complete thermochemical analysis will be made of the measurements. Some of the results have been referred to in a survey paper' covering the types of hydrogen behavior observed in zirconium alloys. LITERATURE ZrCr2 is the only intermetallic phase in the Zr-Cr system.' It exists in two allotropic modifications. Between 900" and 1000°C the hexagonal MgZa (C14) structure transforms into the cubic MgCu2 (C15) structure. Beck4 has previously shown that the intermetallic ZrCrz takes up hydrogen into solid solution up to a composition H/ZrCr2 = 1.14 at room temperature and 1 atm hydrogen. A ZrCr2 hydride was stated to have a fcc structure. The binary Zr-V system has been investigated by williams5 although Rostoker and Yamamoto 6 had given earlier a partial phase diagram. ZrV2 was the only intermediate phase found in the system. wallbaum7 reported earlier that the compound ZrV2 hp the MgZm (CJ4) type structure with a = 5.288A and c = 8.664A. This was not comfirmed by Elliot8 nor by Matthias, Compton, and corenzwit9 who reported that ZrV2 has a cubic MgCua LC15) type structure. The latter authors gave a = 7.429A. Also, several authors do not agree on the temperature of the peri-tectic horizontal. It appears that ZrV2 may exist in several modifications. A high capacity for occluding hydrogen was reported by Beck4 who found H/ZrV2 = 1.38 at room temperature and 1 atm of hydrogen. ZrMoz is the only intermetallic phase in the Zr-Mo system.10 ZrMoa is formed by a peritectic reaction of the melt with a molybdenum-rich solid solution. ZrMo2 has the C15-type structure with a = 7.59A. MATERIALS High-purity chromium, vanadium, and molybdenum were used together with grade 1 crystal bar zirconium to prepare the alloys. Table I lists the chemical analysis and the sources for the metals. Ten-gram alloy compacts were levitated and melted in an inert argon

Jan 1, 1968