Search Documents

By J. B. Dilworth

OUTCROPS of coal have bees discovered is many localities is the Philippine archipelago, and practically all of the larger islands contain deposits of this mineral. Very little prospecting has been done to determine the value of the various coal-bearing areas, but so far as known, the largest and most promising fields are found : (1) is northern Cebu; (2) is the small island of Batan, a part of the province of Albay is southeasten Luzon; (3) is the somewhat larger island of Polillo, off the east coast of Luzon, and (4) is southern Mindoro, sear the small coast tows of Bulalacao. Northern Panay, south-central Cebu, and various localities is southern Luzon, Masbate, Negros, and Mindanao also afford evidences of the existence of coal-beds, the extent and value of which have not yet bees proved. The general position of these islands and districts is shows on the map of a portion of the Philippine Islands, Fig. 1. Some of these coal-fields have been known for many years (coal was discovered is Cebu 1827 and is Batas is 1842),1 and several futile attempts were made by the Spaniards to operate mines is these districts. But owing to many circumstances, chief among which were indifferent management, the political unrest of the islands, natural difficulties of transportation, and those inherent in the mining of steeply-inclined and somewhat irregular seams, no considerable output was ever obtained from any of these mines, and the fuel required is the many departments of industrial and political life has continued to be drawn largely from Australia and Japan. These conditions exist to a great degree at present, and though much interest is the coal-deposits of the Philippines

Jan 1, 1909

By F. F. Aplan, P. H. de Bruyn

The adsorption density of hexyl mercaptan was measured at the gold-solution and the gold-vapor interfaces. This collector is strongly adsorbed at low concentrations, a monomolecular layer being formed at the gold-solution interface at concentrations as low as 2 x 10'6 moles per liter. A maximum contact angle of 83 ± 3° is observed. From a thermodynamic analysis of the experimental data the changes in surface tension at the gold-gas and gold-solution interface are calculated. The data also suggest that the adsorption density of mercaptan at the gold-gas interface exceeds that at the gold-solution interface. In the equilibrium state, a simple flotation system consists of three phases, the solid to be floated, air, and an aqueous solution in stable contact along a line. During the process leading to this final state, a solid-gas interface is created at the expense of a portion of the liquid-gas and solid-liquid interfaces. This change of state is achieved by addition of a collector and, if necessary, suitable modifying agents to the system. By a combined application of the Gibbs Adsorption and the Young Equations, de Bruyn, Overbeek and Schuhmannl were able to show theoretically that the equilibrium distribution of the collector at all three interfaces determines the magnitude of the contact angle. Their analysis led them to conclude that the equilibrium adsorption density of the collector at the solid-gas interface exceeds its density at the solid- liquid interface. This paper succeeded in focussing attention on the neglected role of the solid-gas interface in flotation. In recent years the application of radiotracer, infrared, electrochemical and electro-kinetic techniques to studies of the solid-liquid interface2-5 enhanced our understanding of adsorption processes at this interface. Except for the measurement of contact angles, the solid-gas interface received no attention in fundamental flotation studies. In an attempt to apply the analysis of de Bruyn, Overbeek and Schuhmann to a simple flotation system, an investigation of the adsorption of hexyl mercaptan onto gold was undertaken. Gold was chosen as the solid phase in order to keep the number of dissolved chemical species in the solution phase to a minimum. Hexyl mercaptan (1 - hexanethiol) was selected as collector because its relatively high vapor pressure at room temperature makes it possible to obtain adsorption measurements at the solid-gas interface. This flotation system consists, therefore, of a pure solid phase (gold), an aqueous solution of a weakly dissociated collector (1 -hexanethiol), and a gaseous phase, nitrogen saturated with respect to both water vapor and mercaptan vapor. EXPERIMENTAL MATERIALS AND METHODS Materials: Liquid 1-hexanethiol (C6H13SH) was obtained from Distillation Products Industries and was further purified by double distillation. The purity of the final product was established by boiling point and refractive index measurements. For the adsorption studies from aqueous solution, the radiotracer element, sulfur-35, (half life 87.1 days, 0.169 Mev beta ray) was synthesized into the mercaptan by Tracerlab Inc., Boston, Mass. A close boiling fraction of the synthesized compound was used in the adsorption studies. The specific activity of the radioactive compound was 10 millicuries per gram.

Jan 1, 1963

By means of top-slicing methods, wide veins, masses, or thick beds of soft ore may be mined, where the caving of the overburden is of no consequence. The ore is mined in a series of horizontal floors or slices, taken in descending order, from the top of the deposit. Each floor is mined in small sections, the roof of each section being allowed or forced to cave before an adjacent section is attacked. The method as used in two mining districts—Marquette, iron, and Pachuca, silver-gold—is described in the two papers following:

Jan 1, 1925

By Herbert H. Kellogg, Hugo Vasquez- Rosas

Recently the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authorsl-5-l8 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, laurylamine hydro-chloride, as a collector for the flotation of galena-sphalerite ores. The results show that laurylamine hydrochloride (LAmHCl), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. Contact-angle Tests The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-coverkd glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the clean surface to air or any other source of contamination.

Jan 1, 1947

By Herbert H. Kellogg, Hugo Vasquez- Rosas

Recently the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authorsl-5-l8 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, laurylamine hydro-chloride, as a collector for the flotation of galena-sphalerite ores. The results show that laurylamine hydrochloride (LAmHCl), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. Contact-angle Tests The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-coverkd glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the clean surface to air or any other source of contamination.

Jan 1, 1947

By D. P. Harris

The construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area is postulated. The questions (1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and (2) can this geology be related mathematically to mineral wealth and probability are answered in a case study of 97,000 square miles in Arizona and New Mexico. Measurements on mineral wealth and geologic variables of 243 cells were made. The geologic variables, valued in counts, percentages and lengths, quantified the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. The cells of explored area must be allotted the value class indicated by their cumulative production and estimate reserves (given well-defined geological relationships in a mineral wealth area), and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. This determines whether high value cells can be distinguished from low value cells by their geology as well as indicating those cells misclassified by the model into a higher value group than warranted by their known mineral wealth. The second use of the model is for extrapolation. It is demonstrated how geologic information on an explored area can be utilized in guiding exploration in an unexplored area. Exploration decisions can be predicted on explicitly determined measures of uncertainty (the probabilities). SUMMARY This study postulates the construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area. Such a model will distinguish those cells deserving further exploration on the basis of their geology: The basic postulates of this study are as follows: v = Q(R,S,F,A) P(V) = G(R,S,F,A,V), where V = a measure of mineral wealth P(V) = the probability of occurrence of V R = age and type of rock F = rock fracturing A =age of igneous activity and contact relationships. There are really two questions to be answered: 1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and 2) can this geology be related mathematically to mineral wealth and probability? In order to answer these questions, an area of about 97,000 square miles situated chiefly in Arizona and New Mexico was selected as a case study. This case study area was divided into 243 cells, each 20 miles square, and measurements were made on mineral wealth and geologic variables. Crude geologic variables valued in counts, percentages and lengths are constructed to reflect the above postulated variables. These measurement variables thus provide quantified values defining the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and the multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. Given the availability of an area that is well explored and upon which the relationships of mineral wealth to geology can be adequately defined, there are two ways in which the analysis outlined in this paper can prove beneficial. First, the cells of the explored area must be allotted the value class indicated by their cumulative production and estimated reserves, and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. Such an analysis determines whether cells of high

Jan 1, 1967

By Raymond Ward

IN the past few years several papers have appeared dealing with different aspects of the oxidation of dilute alloys, especially with respect to the formation of internal oxides or subscales. Subscale has been defined1 as that layer or zone of oxide particles precipitated in a matrix of metallic metal in which the oxide particles are dispersed uniformly and occur by diffusion of the oxygen inward from the metal surface. Alloys composed of a solvent metal more noble than the alloying elements are subject to subscaling or internal oxidation. In these alloys the solute must be present in such quantities that if the alloy is exposed to an oxidizing atmosphere at elevated temperatures, the rate of diffusion of the oxygen into the metal will be greater than the rate of diffusion of the solute outward. There is a composition range of the iron-silicon system that falls into this classification. Knowledge of the nature and rates of oxidation of iron-silicon alloys is of great commercial importance, but very little information of this nature is available. Darken2 recently has made calculations to show the limits of concentration of silicon for which subscales are produced in iron-silicon alloys; however, the main thesis of his paper was to analyze and to explain the already existing data. The purpose of this paper is to present the effect of com position, temperature, time, and atmosphere on the type of scale-metal layer obtained and to give some qualitative indication of the effect of these variables on the rates of oxidation. Since this paper is a study of silicon steels that are available commercially, extremely low-silicon and high-silicon alloys are not included. EXPERIMENTAL PROCEDURE The alloys used in the experiment were taken from heats of silicon steel that ranged in analysis from 0.70 to 5.8 per cent silicon. This composition range takes in most of the commercial silicon steels. In Table I are listed the compositions of alloys used. Other than iron and silicon, the alloys normally contained approximately the following impurities: carbon, 0.03 per cent; manganese, 0.07; phosphorus, 0.008; sulphur, 0.02; copper, 0.07; tin, 0.01, and from nil to a trace of chromium, nickel and copper. All of the alloys used were melted in open-hearth furnaces, except where otherwise noted, and were hot-rolled to 0.100-in. plate. Samples approximately 1/2 in. square were then cut from these materials. So that the surface conditions of the samples used for oxidation would be standardized, each sample was ground through 000 emery paper immediately before oxidation. Two different techniques were employed in carrying out the oxidizing treatments. One consisted simply of heating the samples with free access to air. In this treatment the samples were set on edge on a refrac-

Jan 1, 1945

By Dever C. Ashmead

Anthracite was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and the method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they are mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracitc. Mining Methods and Their Relation to Preparation In the beginning of the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a, knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal. Real mining of anthracite began about 1808 when Judge Jesse Fell, of Wilkes-Barre, discovered that the "common stone coal of the valley" could be burned in an open grate. For some years thereafter mining was conducted near the surface. The working p1aces were driven narrow; only the best of the coal was selected and the remainder was left in the ground. Only the lumps could be used, as no market existed for other sizes. As time passed, however, it became necessary either to go farther into the ground or to widen the working places. When these places were widened, falls of roof were apt to occur, making it necessary

Jan 1, 1922

By J. W. Pugh

PREFERRED orientations in cold-rolled body-centered-cubic metals appear to have remarkable similarity. The as-cold-rolled textures in iron,1,2 silicon-iron,3 mild steel,4 molybdenum, vanadium,&apos; chromium,&apos; tantalum,&apos; tungsten,&apos; and a-zirconium-niobium alloys10 have been determined. These textures have, in some cases, been represented by congrUOUS pole figures and have all been described in one or both of two ways. They have frequently been reported as predominantly (100) <011> orientation

Jan 1, 1959

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By C. E. Birchenall, J. R. Stubbles

ThE equilibrium between lead, lead sulfide (PbS), and atmospheres of H2 and H2S has been determined previously by Jellinek and Deubel,&apos; and SudO.&apos; Blbem and Kroger3,4 used Jellinek&apos;s data to calculate the sulfur dissociation pressures of PbS crystals (of

Jan 1, 1960

By C. W. Dunham

DESIGN of the structures for the Morenci Reduction Works involved many interesting problems. Naturally, the chief purpose of these structures is to house and support the equipment and other things necessary for or incidental to the conduct of production. hence most of the features of the design were developed to suit these particular conditions; however, several are so generally applicable as to warrant description.

Jan 1, 1942

D EC. 20-The spirit of Christmas and good will toward men has managed a few brief appearances on the front pages, welcome relief from man&apos;s usual ill-will toward man. A couple politicos did their best to brighten the scene by well-publicized romances. There was a general exodus to Florida to patch up nervous systems, and even the UNO quieted down as Mr. Vyshinsky departed for home via Eastern Germany. Before going he opened up a preliminary bombardment for the worldwide "communist peace offensive," and it is now the duty of the 600 million (according to the Cominform) ideological converts to press home the attack. In Washington, Mr. Lilienthal resigned as Chairman of the Atomic Energy Commission and demonstrated again the difficulty of government to retain the services of capable men. The President has yet to appoint another victim- possibly someone nicely noncontroversial and timid. So might the critics be appeased, but it would bode ill for the rapid exploitation of peaceful uses of atomic energy, the relaxation of excessive secrecy, wider sharing of developmental work with friendly nations and possible revision of the Acheson-Lilienthal proposals for inter- national control of the atomic bomb.

Jan 1, 1950

By J. Price Wetherill

THE coal-seams that are worked vary from 32 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations ; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the. general system pursued is to reach with a permanent outlet such a point in the seam as will

Jan 1, 1877

By Quentin D. Singewald, B. S. Butler

Some of the broader relations between structure and ore deposition along the London fault, deduced from a thorough study of the geology of the eastern part of the Mosquito Range, should be of general interest to economic geologists. The first part of this paper is a generalized statement of the geology of the region in which the London fault is located; it may be supplemented by reference to several earlier publications by the writers and to the U. S. Geological Survey&apos;s Professional Paper 148, on the Leadville district. The second part deals with the structure of both the fault and the disturbed zone adjoining the fault. The third part discusses the salient features of the ore deposits, particularly emphasizing structural control. The two generalized maps are complementary to one another but contain too many data to show on a single small map. The London fault is between Leadville and Alma, and the ore deposits along it are said to lie in the Alma district. Field work in this district, during six summers since 1927, has been a part of the cooperative work of the U. S. Geological Survey, the State of Colorado, and the Colorado Metal Mining Board. The writers have made use of work by R. D. Butler, J. W. Vanderwilt and R. E. Landon. G. F. Loughlin and C. H. Behre, Jr., who have worked on the west side of the range, have contributed valuable suggestions. Mining men of the district have aided in many ways. General Geology Pre-Cambrian Rocks.—The oldest rocks in the district are schists, correlated with the Idaho Springs formation of the Front Range. Quartz-mica schist predominates, but other types occur locally; almost everywhere the rocks show considerable lit-par-lit injection. Intrusive into the schists are two varieties of granite, only one of which is widespread. It is a fine-grained, porphyritie, gray granite correlated with the Silver Plume granite of the Front Range. Near the head of Buckskin Gulch a

Jan 1, 1937

By T. Fraser, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of freeimpurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal.

Jan 1, 1949

By Warnie Flint

PERSONAL INJURY ACCIDENTS According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. NO one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who arc living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they arc utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of Knowledge or skill. 2) Conflicting motivations, such as: (a) to be more conformable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, hut not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

By Perry Olcott .

THE Taka oil field is in the northern part of Titus and Franklin Counties, in north- eastern Texas. The small town of Talco, from which the field derives its name, is on the P. & Mt. P. R. R., about 15 mi. north of Mt. Pleasant, the county seat of Titus County. The oil field extends east and west from the town of Talco, the approximate center. In May, 1924, R. L. Cannon, while doing surface geology for the Humble. Oil & Refining Co., mapped the surface trace of this fault structure as evidenced by Upper Midway faulted down against Lower Midway. In the interval of sixteen years between the original surface work and the recent productive well completion, approximately eight wells were drilled into the Woodbine sand without success. The structure was well defined by those tests and all of the wells en-

Jan 1, 1936

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,&apos; 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956

By Verne E. Hooker, Robert M. Becker

The evaluation of in-situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is aniso tropic. A plane elasticity solution fora circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated. The determination of in-situ rock stresses from boreholc deformation measurements has gained widespread acceptance. Hastl measured the change in diameter of a borehole that was stress-relieved by drilling a larger concentric core; this overcoring method has produced a major portion of the field data for recent stress evaluations in rock. These evaluations are based on the elastic properties of the rock, which are conveniently determined by testing the overcore.6-8 The stress evaluation and the overcore testing procedures generally assume isotropic relations whereas rock is anisotropic in varying degrees. Recently, an anisotropic plane stress solution was adapted for evaluation of in-situ stress9 and a related plane strain solution was developed for the testing of stress-relief core. 10 The present paper unifies the stress evaluation and overcore testing procedures for a general class of anisotropic rock. Equations are presented for calculating the state of stress in a plane normal to the borehole, and a consistent thick-wall cylinder solution is given for determining the necessary elastic properties. In addition, a complete example of stress evaluation from laboratory and field data is presented, and the order of error in computing the state of stress from isotropic relations is illustrated. Several limitations of the results should be emphasized. All results assume small linearly elastic deformations of a homogeneous medium. Rock characterized by orthotropic, transversely isotropic, and isotropic elasticity is considered; however, the anisotropic results assume a special relation among certain elastic constants in addition to geometric orientation with respect to a plane of elastic symmetry. For some stress determinations in rock, these may be severe limitations. On the other hand, the anisotropic evaluation procedure involves little additional effort and is much more flexible than the corresponding isotropic evaluation procedure. The collection of field data is identical. The laboratory determination of elastic parameters is no more difficult and time-consuming for the anisotropic than for the isotropic model. Only the calculations require some additional effort for the anisotropic evaluation, and this additional effort is eliminated by use of a small computer. The flexibility of the anisotropic procedure is greater because more than two independent elastic constants are available in fitting rock data. For the special relationship assumed among orthotropic constants, five independent elastic constants are available for the determination of in-situ secondary principal stresses as compared with two independent elastic constants for the isotropic model. Much of the material presented is either directly from the literature or adapted from the literature through superposition or the usual transformations. Consequently, only enough detail for clarity of presentation is included. RELATIONS FROM ANISOTROPIC ELASTICITY Materials that have three mutually orthogonal planes of elastic symmetry are called orthotropic. By directing the axes of the coordinates perpendicular to these planes, Hooke&apos;s law for an orthotropic solid 11 is

Jan 1, 1970