Search Documents

By C. W. Mason

TIN has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphur. The notorious "tin disease," which Cohen1 has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white 0 tin to cubic gray a tin, has apparently encouraged the expectation that one or more addi-tional polymorphic modifications might exist. The search for confirma-tion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but for previous assumptions. The ball apparently was started rolling in 1880 by Trechmann,' who reported a new modification of tin (y tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be y tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller.3 Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,6 by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) and stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencer3 in 1921 examined the above evidence critically; he found similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on a second lot of crystals, not described crystallographically.)

Jan 1, 1939

By Henry P. Ehrlinger

THE Alta and St. Louis mines of the Alta Mines, Inc., produce a somewhat oxidized ore with a talc gangue that presents quite a problem in milling. For several years the mill recoveries were relatively low and there seemed to be no cure for this condition even with increasing the various collecting agents and frothers to two or three times of what they should be. The usual alibi of "oxidized ore" was given as the reason for these results and the matter stood there for some time until these investigations were started. FLOWSHEET As a brief outline of the flowsheet the ore is crushed to minus I in. in a Telsmith jaw crusher and then fed to a 64 1/2 Marcy grate mill. The resulting product from the grate mill is passed over a trommel where the coarse particles (plus 7 mesh) are returned to the grinding circuit through the classifier. The under 7-mesh pulp is passed over two Denver mineral jigs where a high grade concentrate is produced, thence over two Wilfley tables where a table concentrate is produced and about 80 pct of the oxide lead recovered. The tailings from these tables are pumped back to the classifier and after classification the 30 pct pulp density product, which overflows the lip, is passed into a series of 10 Denver economy flotation cells where a lead-copper concentrate is produced. Three products are made and shipped to the smelter termed jig, table and float concentrates. RESULTS WITH VARIOUS REAGENTS In March of this year work was started on the metallurgical problems of the mill and, as is shown in Table I, the results obtained were not too efficient. [ ] Tests were run with various reagent combinations that were recommended for ores of this nature but there was no appreciable effect on the recoveries. The grades of the flotation concentrates were reduced by the insoluble picked up and retained by these more powerful collectors and frothers. RESULTS WITH "METSO" In past work on ores of this type the use of "Metso" had improved gold and lead recoveries, but no effect on the silver and copper recoveries had been noted. To

Jan 1, 1947

By P. Gobin, J. Perez, P. Peguin

The strain-amplitude- dependent part of the internal friction of alluminum after several ther momechanical treatments has been measured in the I-cycle range and at the ambient temperature. The internal friction in the outer layer of the torsional specimen us stress is computed from the experimental data. The curues obtained are analyzed in tevnzs of u coirzbinntion of AH and p, which aye, respectively, due to the vecersible unpinning from weak pills and to the plastic strain. Considerirlg the notion of thermally activated unpinning and repinning, it is shown that in our experimental conditions tlze dislocation lines acl as in the H model of Granato and Liiclze. It is also seen that the internal friction p which appears at higher- strains call be described by a simple expression which is in good agreement with our results. A qualitative interpretatiorz is proposed by combining these new types of intelpnal fviction. We define the internal friction 6 as half the ratio of the dissipated energy aW during one cycle to the maximum supplied strain energy W of a material submitted to a periodic stress. Experiment and theory show that internal friction varies with stress above a critical value.' Below this value the internal friction is strain-amplitude-independent and is often masked by an experimental background; so we shall call it AB. ~bove this critical value, the internal friction is strain-amplitude-dependent. This quantity is usually called aH:' and it can be explained as a thermal unpinning of dislocations.3-6 Furthermore, at higher stresses, a rapid increase of internal friction appears. This phenomenon could be caused by the plastic strain,' so we shall call it Ap. It seems interesting to us to study the influence of several t her momechanical treatments on the curve internal friction 6 vs strain E, in order to study the variation of AH and p with the concentration and the repartition of linear and point defects. In order to try to explain the results obtained, we shall propose and discuss models for H and hp and shall show that we obtain a combination of these two types of internal friction. 1) EXPERIMENTAL PROCEDURE 1) Preparation and Treatment of Specimens. We

Jan 1, 1968

Secretary's Note.—M. Beutter's introductory remarks, being simply a resume of Prof. Hone's paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution lias been somewhat condensed, without omitting any essential statements. M. Beutter, St. Etienne, France* (communication to the Secretary†):—Professor Home observes in $ 47 of his paper that the fluid-compression of steel diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingmorth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forg-ings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without danger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jan 1, 1908

By N. J. Themelis, P. Spira

The efficiency of the reverberatory furnace operation in producing. slags of 1020 copper content depends on the mixing and flow conditions in the bath. Radioactize-tmcer tests have indicated the jkaction of bath volume engaged inflow and the mixing conditions in the bath. The factors controlling the flow pattern of slag have been classified as laminar transfer flow, natrsral convection, and flou, due to the rapid addition or removal of slag.. Similarity criteria for model studies have been developed. The pyrometallurgical processing of copper begins with the smelting of either flotation concentrates, or direct-smelting ores which have been partially roasted to calcines. These materials are generally smelted in a reverberatory furnace, Fig. 1, and separate into two liquid phases, a sulfide matte and an iron silicate slag. he matte is tapped and subsequently reduced to metallic copper in a converter, while the reverberatory slag is usually discarded without any further treatment. Molten slag from the converting operation is returned intermittently to the reverberatory in order to recover its high copper content (1 to 3 pct Cu). The reverberatory furnace is about 115 ft long by 30 ft wide. In general, the solid charge is fed at intervals through openings along the sides of the roof and forms sloping banks from which the molten materials trickle down into the bath; the charge banks extend over a length of about 70 ft from the firing wall. The depth of the slag and matte layers varies from smelter to smelter; in the Noranda furnaces, the slag depth is 24 to 30 in., while the depth of matte at the taphole is about 20 in. Apart from smelting, the functions of the reverberatory are to recover most of the copper content in the converter slag by physical and chemical interaction with the furnace bath, and to provide adequate time for optimum separation between matte and slag. The efficiency of these operations depends on the mixing and flow conditions in the bath and is reflected on the copper losses in the slag. In the present study, the reverberatory furnace is considered as an open-channel chemical reactor and the driving forces for material transport through the bath are examined by means of flow and mathematical models. FLOW CONDITIONS IN THE REVERBERATORY FURNACE To facilitate the study of mixing conditions in continuous-flow reactors, two idealized patterns of flow have been accepted by workers in this field.' The term "backmix" flow is used to describe complete and instantaneous mixing in the reactor (perfect mixing); all particles have the same chance of leaving the system, independently of their time of entrance, and the fluid is uniform in composition throughout the vessel. On the other hand, "plug" flow, or "piston" flow, assumes that a fluid element moves through the reactor without overtaking or mixing with fluid entering at an earlier or later time. In addition to the two idealized patterns of flow, "deadwater" flow accounts for that portion of the fluid which is moving so slowly that it may be assumed to be stagnant. According to the definition by evensppiel,' the cut-off point between active and stagnant fluid may be taken as material which stays in the vessel for a period twice the mean residence time. The flow patterns in real vessels may be approximated by a combination of the above flows. Thus, the vessel is assumed to consist of interconnected flow regions with various modes of flow existing between them. The flow pattern may be determined directly from the flow paths of fluid through the essel. -However, the difficulty of obtaining and interpreting such information has led to the alternate approach of determining the residence time distribution of fluid elements by means of stimulus-response studies. The stimulus is provided by introducing a tracer in the inlet stream and the response by the record of the change in tracer concentration in the exit stream from the reactor. Such tests have been conducted in glass tank furnaces using either chemical7"9 or radioactive tracers1'-'' and, in one case, experiments have been reported for a metallurgical furnace.'"

Jan 1, 1967

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance' present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.' As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972

By John Henry Harden

This shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & WilkesBarre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51' 2" long, 17' 4" wide, 31' deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45' 4" long, 11' 16" wide, 31' deep, divided into six parts by buttons 8" x 12", each division, 7' x 11' 6". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10" ; backing, 3" thick ; clay puddle to exclude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the "standard diamond " car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet." Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pressure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams.

By J. M. Vetter, W. F. Bowman

The Gulf Coast area of Texas and Louisiana produced a total of 47,070,650 bbl. of oil during 1928, a decrease of 7,401,173 bbl. from the previous year. Of this amount Texas produced 39,353,950 bbl., or a decrease of 9,689,296 bbl. from the 1927 output. The Louisiana Gulf Coast produced 7,716,700 bbl., which is an increase of 2,288,123 bbl. over 1927. The decrease in the Texas Coastal area is due principally to the decline at Spindletop. Production at the beginning of the year in this field averaged 53,400 bbl. daily. At the end it had declined to 35,850 bbl. The increase in Louisiana was due to development in new fields at Kelso Bayou (East Hackberry), Sulphur, Sweet Lake, Bayou Boullion and Sorrento. This production was maintained by the drilling of 984 wells. Of this number 736 were located in Texas and 248 in Louisiana. Of the 984 wells drilled, 571 were reported as producers. Distribution of the various completions is listed in the accompanying tables compiled by Oil Weekly. New Developments New developments of particular importance in Texas were the finding of a 5000-bbl. well in formations of Cook Mountain age in the Clay Creek field located in northern Washington County by the Sun Oil Co. ; the discovery of oil at Dewalt in Fort Bend County by the Humble Oil & Refining Co.; the development of commercial production at Raccoon Bend in Austin County by the same company; and the finding of oil in formations of Oligocene age in the Refugio gas field of Refugio County. The most important development in Louisiana was the finding of oil at Sorrento, east of the Mississippi River, by the Gulf Production Co. The importance connected with these finds is not so great in that they opened up new fields, but in the new territories which they open as possibly productive of oil. Eastern Louisiana has been looked upon with considerable doubt on account of the theory which has prevailed among most geologists that the nature of the formations was not such as to produce oil. The actual finding of oil in that area upsets this theory and

Jan 1, 1929

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943

By L. S. Darken

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By J. W. Clark, C. T. Sims

Wrought chromium-base alloys containing yttrium, cubic monocarbides of the Ti(Zr)C type, and similay alloys containing manganese and rhenium have been melted and fabricated. Strength has been studied by hot hardness and elevated-temperature tensile and rupture measurements, low-temperature ductility by tensile testing, and surface stability by oxidation testing. In additiod, studies have been conducted of the carbide stability, and of aging behavior. The carbide dispersion generates effective elevated-temperature strength, which is further enhanced hv strain-induced precipitation. The dispersion exhibits classical dissolution and aging response. The ductile-to-brittle transition temperature of these alloys is above room temperature. The alloys reported show fairly good oxidation resistance, but nitrogen contamination can cause fortnation of a hard Cr2N layer under the oxide scale. Manganese does not appear to be a promising alloying element in chromium. In the years 1945 to 1950, the metal chromium was considered as a possible base for alloy systems due to its considerably higher melting point than superalloys, its low density, its high thermal conductivity, and its apparent capacity for strengthening. However, this interest in chromium was short-lived. It was found difficult to melt and cast, to be exceptionally sensitive to the effect of minor imperfections, to have a lack of ductility at both room and elevated temperatures, and to be subject to a deleterious effect of alloying elements upon the ductile-to-brittle transition temperature.' Since then, chromium, as a practical alloy base, has remained virtually unstudied. Further, purposeful ignoring of chromium has been promoted by statements that its bcc structure would not allow it to be strengthened to useful values, when compared to the "austenitic" alloys.2 Recently, a new look has been taken at chromium-base alloy systems. Study of the literature will show that chromium, providing some of its disadvantages could be eliminated or minimized, actually has a rather attractive potential as an alloy-system base. Analysis of rather scattered data suggests that chromium is quite capable of being strengthened to high levels. Also, significant strengthening of its two sister elements in Group VI-A, molybdenum and tungsten, has been demonstrated in a number of commercial and exploratory alloys. Chromium should be similar. Since chromium does not readily form a volatile oxide like tungsten or molybdenum, it offers a much higher probability of giving birth to alloy systems with useful oxidation resistance. Concerns about possible high elemental vapor pressure have been mitigated by recent data.3 In addition, the physical properties exhibited by chromium are attractive for application as a high-temperature structural material. For instance, its thermal conductivity varies from 49 to 36 Btu-ft/hr-sq ft-°F over its range of usefulness (which is two to four times higher than most superalloys), its density is about 7.2 g per cc (20 pct less than most nickel-base alloys), its coefficient of thermal expansion varies from 4 to 8 x 10-6 per OF, and it has a relatively high modulus of elasticity, approximately 42 x 10' psi.4 Alloying studies on a chromium base in the past have usually encompassed rather sweeping solid-solution alloy additions for strengthening. This is not consistent with contemporary alloying practice in Group VI-A. For instance, molybdenum, also in Group VI-A, is primarily alloyed for strength improvement by use of heat-treatable carbide dispersions.5 Chromium and molybdenum are similar in their chemical activity and other properties. Thus, strengthening of chromium by carbide dispersions was studied. Chromium-base alloys are plagued with room-temperature brittleness, although high-purity unal-loyed chromium can be made ductile.4,8 Use of yttrium as a scavenger has done much to improve ductility and resistance to nitrogen embrittlement in chromium systems,7 so it was utilized in this program. It has also recently been found8 that small rhenium additions (1 to 5 pct) create improvement in the ductility of Type 218 tungsten wire. This is apparently related to the remarkable effect of rhenium additions near its terminal solid solubility in all Group VI-A metals.9'10 Investigation to establish if dilute concentrations of rhenium would also be effective in chromium appeared to be logical for this program. Since rhenium is too expensive to be practical in alloys for application as structural components, ductility improvements through solid-solution alloying were also sought by substitution of manganese for rhenium; manganese, like rhenium, exists in Group VII of the periodic system. The optimum amount of carbide dispersion for chromium-base alloys was obtained by analogy with molybdenum. Strengthening in molybdenum is achieved by use of Ti-Zr carbide dispersions. A

Jan 1, 1964

By Henry P. Ehrlinger

The Alta and St. Louis mines of the Alta Mines, Inc., produce a somewhat oxidized ore with a talc gangue that presents quite a problem in milling. For several years the mill recoveries were relatively low and there seemed to be no cure for this condition even with increasing the various collecting agents and frothers to two or three times of what they should be. The usual alibi of "oxidized ore" was given as the reason for these results and the matter stood there for some time until these investigations were started. Flowsheet As a brief outline of the flowsheet the ore is crushed to minus I in. in a Telsmith jaw crusher and then fed to a 64½ Marcy grate mill. The resulting product from the grate mill is passed over a trommel where the coarse particles (plus 7 mesh) are returned to the grinding circuit through the classifier. The under 7-mesh pulp is passed over two Denver mineral jigs where a high grade concentrate is produced, thence over two Wilfley tables where a table concentrate is produced and about 80 pct of the oxide lead recovered. The tailings from these tables are pumped back to the classifier and after classification the 30 pct pulp density product, which overflows the lip, is passed into a series of 10 Denver economy flotation cells where a lead-copper concentrate is produced. Three products are made and shipped to the smelter termed jig, table and float concentrates. Results with various Reagents In March of this year work was started on the metallurgical problems of the mill and, as is shown in Table I, the results obtained were not too efficient. Tests were run with various reagent combinations that were recommended for ores of this nature but there was no appreciable effect on the recoveries. The grades of the flotation concentrates were reduced by the insoluble picked up and retained by these more powerful collectors and frothers. Results with "Metso" In past work on ores of this type the use of "Metso" had improved gold and lead recoveries, but no effect on the silver and copper recoveries had been noted. To

Jan 1, 1949

By O. J. Hollister

Jan 1, 1888

By M. D. Hassialis

THE object of a technical paper is to communicate new technical knowledge, the paper being the vehicle of communication and the existence of new knowledge its reason for being. It follows that the development of information worthy of communication, the criterion being novelty, is prerequisite to exercising the privilege of communication. The act of communication is achieved when the reader perceives the nature of the new knowledge, i.e., when he understands it. A paper achieving this objective is an acceptable technical paper. Development of new knowledge has as one of its purposes the increase of the existing state of knowledge and the enjoyment of the benefits derived therefrom. Technical knowledge is a collection of facts so ordered as to make apparent, relations existing between the facts. When the interrelations have been exposed the facts have been interpreted or explained Three broad, overlapping categories of technical papers may be recognized: papers consisting of (a) a report of facts, (b) an explanation of facts, or (c) a combination of a report and an interpretation. Ideally a technical paper should belong to one of the last two categories but current practice is to accept papers belonging to any of the three categories. Based on a small sample drawn from the scientific and engineering literature, the relative frequency of the three types is a: b: c:: 20:1:14. If the sample be limited to engineering literature, the ratios become a:c::2:1; type (b) being nonexistent. This large departure from the ideal is a consequent of the

Jan 1, 1948

New Jersey Zinc Co. - The Mines Franklin-Sterling Friedensville Development Austinville Ivanhoe Development Eagle Mine Hanover

Jan 12, 1953

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphates from the soil. Man's most important use of phosphate is for fertilizer; approximately 95% of the world's phosphate rock production is consumed by fertilizers. Most of the balance is processed in electric furnaces into elemental phosphorus, the important raw material for making industrial phosphates. Recovery of uranium from phosphates has been possible but not widely used. However, recent significant developments have generated interest in such recovery in the US and elsewhere. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and salt water. However, economical recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade_ and must be concentrated. Phosphate rock is produced in 31 countries. Fig. 1 shows the location of major phosphate rock producers as well as some of the known phosphate deposits not yet in production. In the last decade the world phosphate industry has experienced steady growth. World production rose from 98 Mt of phosphate rock in 1973 to 140 Mt in 1982. Fig. 2 shows the growth curve of rock production and graphically illustrates the almost straight-line rise since 1945 in both US and world production. Table 1 gives the breakdown, by countries, of world rock production, 1974 through 1979. Table 2 shows US rock production by producing areas. Definitions of Terms Used in the Phosphate Industry Phosphate Rock: Commonly called rock in sedimentary deposits and apatite in igneous deposits. Those expressions generally include any mined, or mined and beneficiated, fluorine-containing calcium phosphate used as the raw material for the next stage of manufacturing. The average phosphate content in rocks is 0.1 to 0.2% P2O5, as documented by McKelvey (1973). About 200 minerals contain more than 1 % P2O5. However, the important mineral in igneous rocks is fluorapatite, [Ca5 (PO4),3 F], containing about 42% P205 and 3.8% F2; in sedimentary rocks the important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO2. Both are in the apatite family of minerals. Most phosphate rock, whether beneficiated or not, is a fine-grained material. The expression phosphate rock has no relation to its phosphate content. For example, phosphate rock from Idaho used in the production of phosphorus may contain about 24% P205, whereas rock from Morocco may contain 36.6% P2O5. Phosphorite: A deposit of phosphate directly or indirectly of sedimentary origin, which is of economic interest. Grade of Phosphate Rock: The calcium phosphate content of phosphate rock is expressed in different world areas by one of the following terms: BPL (bone phosphate of lime) TPL (triphosphate of lime) P2O5 (phosphorus pentoxide) P (phosphorus-not commonly used) An illustration of relationship is: 80% BPL = 80% TPL = 36.6% P5O2 = 16% P

Jan 1, 1983

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By John W. Cahn

Tile avevage value of the mean curvature of surfaces in a specimen can be precisely delermined by sitrlple measurements performed on random sections or on 1 vojectiotzs of these surfaces. For surjaces enclosing particles, the quanlity is sllown to be velated to the probable tlurrrhev ot particles intevcepted by a random platne and, under certain conditions, to the perimeter of their Projected image and to the increuse in surjace area when the particles grow. Many of the velalionsl~ips are valid for any shape or size of the particles. THE recent growth of the field of stereology or quantitative microscopy is largely the result of the discovery of a limited number of rigorously defined geometrical parameters that can be precisely measured on random sections or projections of a structure without assumption about particle shape.' Such parameters have been the volume fraction and surface area and line length in a unit volume. The present paper introduces the average of the mean curvature of surfaces in a volume, and shows that it can be rigorously measured by counting methods alone. AVERAGE CURVATURE ON A PLANE Consider a curve y = v (x) on the xy plane. The curvature Kp in the plane at any point is given by Kp = (dZy/dx2)/[1 + (dy/dx)2]3/2. The average curvature along the curve may be defined as Kp = (1/L) fKpdl |1] where dl = [(dx)' + {dy)2]1/2 is the length of an element of the curve and .(dl = L is the total length of the curve. The integral on the right-hand side of Eq. [l] will be called the total curvature, It is dimensionless and readily evaluated by substituting d = arctan (dy/dx) to give ah which is the change in direction of the tangents to the ends of the curve, Fig. 1. Hence, Kp = (1/L)(?h) [2] It can also be seen that Eq. [2] is applicable in the limit of sharp corners. Even though the curvature is infinite at a corner, f Kpdl remains integrable and equal to the change of angle. The signs of the quantities Kp and dl are arbitrary and, if the areas adjoining the curve are equivalent, there seems to be no compelling reason to fix the signs. For a closed curve, however, it becomes worthwhile to use the signs to distinguish among different types of areas or phases enclosed. For such a closed curve AO = t2r and As a convention, we shall take the direction of the integration along the curve in such a way that the area or phase under consideration (henceforth called a) is kept to the left side of the curve, Fig. 1. Then Kp is positive where the curve is concave and negative where the curve is convex. For a closed curve Ad - +2n if the curve encloses a, and Ad = —2n if the curve is surrounded by a. PLANAR SECTIONS OF THREE-DIMENSIONAL STRUCTURE OF ISOLATED a PARTICLES Consider next a planar section of a microstructure containing particles of a in a matrix. We place no restriction on shape of connectedness of these particles, and begin by considering the curvature of only the boundary between a particles and matrix' Clumps of contiguous a particles are then treated as a single a particle. The two-dimensional section will show in a unit area na simple closed curves enclosing a particles and nh closed curves of holes, in-

Jan 1, 1968

By Gerald Edmunds, R. K. Waring, E. A. Anderson

Brass is liable to failure under the combined influence of stress, certain corrosion media, and time, a phenomenon commonly termed season cracking or stress-corrosion cracking. The consequences of this are serious in applications of brass generally, including the important field of cartridge cases. Cartridge cases (70 Cu: 30 Zn) that fail from this cause may allow the escape of gas from the gun breech, a hazard to the shooter, and may not eject, thus temporarily putting the gun out of action. In loaded cartridge cases, the stress present is partly residual from the, drawing and necking operations and partly applied by the insertion of the projectile. Ammonia, present as a decomposition product of smokeless powder, air and moisture constitute corrosive media. The prevalence of season cracking has been reduced considerably, but not eliminated, during the past quarter of a century by low-temperature annealing to relieve stresses residual from fabrication, a method suggested by Diegel 38 yr. ago(I).2

Jan 1, 1945