Search Documents

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCI) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2SO4 2MgSO4), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described. The saline strata are nearly flat-lying and comprise interbedded layers of halite, anhydrite (CaSO4), and poly-halite (2CaSO4.MgS04.K2SO4-2H2O), with halite predominating. The halite layers contain local concentrations of sylvite, carnallite (KC1.MgCl2.6H2O), and langbeinite. The principal marker in the potash mines area is a bed of anhydrite about 8 ft thick, and 70 ft below the 800 level. This bed contains varying amounts of polyhalite, and locally a few blebs of sylvite. Two principal marker beds are present over most of the 800 level. The lower is the "Middle Salt Marker," a bed of bright-orange halite, which ranges in thickness from a knife-edge to about 0.6 ft, and is usually bounded above and below by thin seams of green or reddish-brown clay. In langbeinite-rich areas, this marker usually contains abundant blebs of langbeinite. The upper of the two principal markers is a green clay seam, containing abundant halite, which ranges in thickness from 0.1 to about 0.5 ft. It is 2 to slightly more than 5 ft above the Middle Salt Marker. No langbeinite of minable grade is found above this clay, and it

Jan 1, 1950

By J. Rogers, K. L. Sutherland

THE relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. EXPERIMENTAL PROCEDURE The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testing18 have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.25 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By L. B. Herring, Harold Decker

The South Texas area, discussed herein, represents districts 2 and 4 of the Texas Railroad Cominission and extends from Jackson, Lavaca, and Gonzales Counties on the northeast to the Rio Grande River, comprising a total of 26 counties.$ The present boundaries of this district do not coincide with those of earlier reports published in the annual volumes of Petroleum Development and Technology. The war, in its various ramifications, determined and controlled all the phases of the oil and gas industry. Priorities for material and governmental subsidies determined all new operations. New Pools In our opinion, the combine' quantity of crude and distillate reserves added in '943 approached Or possibly exceeded the amount produced. Thirty-five new pools were added to the area' Of these, five have significant reserves and ten offer possibilities of containing consequential reserves. The largest proven reserve discovered during the year was the Slick pool, on the DeWitt-Goliad County line. This is also the most important Wilcox discovery to date in the area. The most significant extension was at Willimar, Willacy County. Other important extensions were developed at Agua Dulce, Seeligson, and Odem. Except for the Porter field, in Karnes County, the Laredo trend, which produces lrom the Jackson and Yegua, proved very disappointing, and this pool is o:C secondary importance. The Scott and Hopper pool, Brooks County, has only orie well, but offers excellent possibilities of becoming an important discovery. It represents at this time the major Frio discovery of the year. The Hobson pool, Karnes County, is not a major reserve, but can be classed as important in that it produces at a shallow depth from the Wilcox. This proves that the potential area of production for this zone occupies a broad trend. Gas and Condensate During the year construction was begun on only one recycling plant, this being in the Sejita field, Duval County. Several others were colltemplated, but no actual operations were begun. The most important development in recycling was the rebuilding of old plants to allow for the fractiona-tion of isopentane, n-butane, isobutane, and propane. Heretofore all pentanes plus have been marketed as cLdistillate,n only a minor portion of the butanes being isolated and sold for fuel purposes. All these new the except propane, are considered vital to the war effort and propane is being marketed as fuel gas. In other instances propane is being isolated and then pumped back into the gas reservoirs for storage. It is anticipated that the demands for this product will increase in the future. Drilling in the Wilcox trend during the year showed the existence of valuable gas

Jan 1, 1944

By L. B. Herring, Harold Decker

The South Texas area, discussed herein, represents districts 2 and 4 of the Texas Railroad Cominission and extends from Jackson, Lavaca, and Gonzales Counties on the northeast to the Rio Grande River, comprising a total of 26 counties.$ The present boundaries of this district do not coincide with those of earlier reports published in the annual volumes of Petroleum Development and Technology. The war, in its various ramifications, determined and controlled all the phases of the oil and gas industry. Priorities for material and governmental subsidies determined all new operations. New Pools In our opinion, the combine' quantity of crude and distillate reserves added in '943 approached Or possibly exceeded the amount produced. Thirty-five new pools were added to the area' Of these, five have significant reserves and ten offer possibilities of containing consequential reserves. The largest proven reserve discovered during the year was the Slick pool, on the DeWitt-Goliad County line. This is also the most important Wilcox discovery to date in the area. The most significant extension was at Willimar, Willacy County. Other important extensions were developed at Agua Dulce, Seeligson, and Odem. Except for the Porter field, in Karnes County, the Laredo trend, which produces lrom the Jackson and Yegua, proved very disappointing, and this pool is o:C secondary importance. The Scott and Hopper pool, Brooks County, has only orie well, but offers excellent possibilities of becoming an important discovery. It represents at this time the major Frio discovery of the year. The Hobson pool, Karnes County, is not a major reserve, but can be classed as important in that it produces at a shallow depth from the Wilcox. This proves that the potential area of production for this zone occupies a broad trend. Gas and Condensate During the year construction was begun on only one recycling plant, this being in the Sejita field, Duval County. Several others were colltemplated, but no actual operations were begun. The most important development in recycling was the rebuilding of old plants to allow for the fractiona-tion of isopentane, n-butane, isobutane, and propane. Heretofore all pentanes plus have been marketed as cLdistillate,n only a minor portion of the butanes being isolated and sold for fuel purposes. All these new the except propane, are considered vital to the war effort and propane is being marketed as fuel gas. In other instances propane is being isolated and then pumped back into the gas reservoirs for storage. It is anticipated that the demands for this product will increase in the future. Drilling in the Wilcox trend during the year showed the existence of valuable gas

Jan 1, 1944

By Harry P. Hohenadel

DURING the past few years the amazing developments of the chemical industry have inspired so much publicity that the feature writers assure us that we are entering a "Chemical Age," industrially as important as the "Steel Age" and the "Electric Age," so-called. Whether or not these assurances are overstatements, it is a fact that the expansion of the chemical industry during the past 25 years has been enormous. The Chemical Bureau of the War Production Board calculates the value of chemicals produced during 1944 at $8,300,000,000, no small sum even in inflated dollars. As concerns us of the Southwest oil and gas country, four significant trends of the chemical industry are most important. (1) Many of the recently developed chemical products are new creations, not substitutes,. as new and original as the invention of the light bulb, and with a field for exploitation almost as wide. (2) Many of these chemical products will enter the mass consuming markets, which require enormous tonnages of products, and such markets are setting up an industrial demand for chemicals on a mass volume basis, compared to the relatively high-priced low-volume basis ordinarily considered as the chemical outlet of the past. (3) Most of the processes involved in producing these chemicals are adapt. able to the use, all or in part, of natural gas, oil, or refinery gases as raw mate-

Jan 1, 1945

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country's production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber's salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

By H. M. Hobart

This paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the greatest economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of_ Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox, of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per sq. in. (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per sq. in. (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows: Works Carbon Content for Plates 1/4 In. Thick 1 In. Thick A..................... 0.14 0.23 B..................... 0.14 0.25 C2.................. 0.19 0.25 D................. 0.20 0.30 E Upper limit..... 0.35 Lower limit..... 0 24 0.29 Upper limit,.... 0.25 0.30 Lower limit..... 0.21 0.27 Upper limit..... 0.25 0.35 Lower limit..... 0.22 0.28

Jan 1, 1920

ALBERT Ladd Colby, who died suddenly of influenza at Torquay, England, on Apr. 30,1924, was born in New York City, on June 26,1860. He was educated in the public schools of New York, at the College of the City of New York, and received the degree of Ph. B. from the Columbia School of Mines in 1881. He continued his studies at Columbia, acting occasionally as assistant to Prof. C. F. Chandler, until 1883. For the next three years he was Assistant Professor of Chemistry in Lehigh University; then head chemist and metallurgical engineer of the Bethlehem Steel Co., at Bethlehem, Pa., occupying the latter position until 1903. As head chemist his active and inventive mind devised several improvements in apparatus for increasing the rapidity and accuracy of the analytical work; as metallurgical engineer, he was, from time to time, in charge of the blast-furnace, open-hearth, bessemer, and puddling departments; he had entire charge of the inspection, assignment, and economic use of all metallurgical materials, and he early gave his attention to the formulation of specifications for metallurgical materials—an activity in which he long held a distinguished part in this country, and as a representative of his own country in England and Europe. He also sewed as expert for his company in patent suits, again laying the foundation for valuable service later as a consulting engineer. In this latter capacity he was excelled by few, if any, contemporaries in the iron and steel industry. His mind was ingenious, thorough, clear, and keen, both in the preparation of evidence and its presentation to the Court. He very quickly appraised the value of evidence, or of an answer to a question, and knew how to secure the infermation, either from the available literature of any language, or by special researches or plant studies. In the executive control of literary research for patent purposes, his long training, infinite capacity for digging through long series of articles in English, German or French, and clear formulation of the vital subject matter for the guidance of assistants, made him invaluable. He was also an adept in collecting information on special branches of his profession. For example, when the science of metallography began to assume importance, he made the first really comprehensive bibliography covering the literature of all siderurgical countries; for the newly formed International Nickel Co. he gathered all the information extant on the subject of nickel steel, both in the literature and in the minds of experts in America and Europe. Two books testify to the thoroughness of his work in this capacity, vie.: "American Standard Specifications for Steel,"

Jan 1, 1924

By Lawrence K. Nordell

This paper reviews practices used In the selection and sizing of belt conveyors and stacker systems commonly used in crushing and grinding plant facilities. Historical and modern methods of sizing this equipment are presented. The new methods Include: 1) probability theory applications for establishing component reliability, 2) "Monte Carlo" simulation techniques used in evaluating alternative system designs and in establishing service factors and corresponding availability Indices of each system, 3) quantifying the system and component operating characteristics using computer assisted modeling tools simulating rigid body and elasto-mechanic behavior for starting and stopping large and/or complex belt conveyors.

Jan 1, 1982

NEW MEMBERS The following list comprises the names of those-persons who became members during the month of January, 1914. Members ADIASSEWICH, ALEXANDER, Dept. of Commerce & Industry, 11, Nadejdinskaia, St. Petersburg, Russia. BEARD, JOHN W., Mine Supt., Lane-Rincon Mines, Inca, Temascaltepec, Mex., Mexico; BORCHERDT, WALTER 0., Supt The Bertha Mineral Co., Austinville, Va BREWSTER, BURT B., Sales Engr., Sullivan Machinery Co., 1127 Central National Bank Bldg., St. Louis, Mo: CHASE, ROGER E., JR., Assayer 3906 No. Baltimore St., Tacoma, Wash. CULBERT, J. VICTOR 7S4 Wellington St., London, Ont., Canada; DICKINSON, ALBERT W., Supt. Of Mines Bevier, MO. DODSON, T. M Mores, Colliery, Schuylkill Co., Pa FORREST, CHARLES N., Chem. Engr Maurer, N. J.

Jan 2, 1914

By J. H. Brophy

Experimental evidence in recent years shows that nickel coated hydrogen reduced tungsten powder can be sintered to 98 pct of theoretical density at 1100°C. New data indicate that the sintering rate is the same for nickel contents ranging from 0.125 wt pct (mon-atomic layer) to 5.0 wt pct Ni coated on 0.561. tungsten powder. Nickel tungsten made by coreduction from oxides sinters in a kinetically similar way, but the rate tends to increase with higher nickel contents. The activation of sintering can be accomplished with a minimum amount of nickel if coated powder is used. Transverse rmpture strength was found to increase in specimens containing 0.25 pct Ni as density increased during the initial stage of the carrier-phase sintering process. Upon the onset of grain growth in the final stage, strength was found to decrease. With increasing nickel contents up to 4 pct, strength increased. Maximum strengths in three-point loading were observed at 73,000 psi for 0.25 pct Ni and 93,000 psi for 5 pct Ni. These were comparable to that of massive tungsten recrystal-lized in the presence of nickel and tested in the same way. The results were sensitive to the mode of powder treatment and ductility was negligible in all cases. The study and application of sintered bodies of nickel and tungsten is not new; however, the analysis of the mechanism by which small additions of nickel increase the sintering rate of tungsten promises to Contribute new information regarding sintering theory in general. Initial experimental evidence was presented by the authors showing that nickel-coated hydrogen-reduced tungsten powder may be sintered to 98 pct of theoretical density at 1100°C in 16 hr.' Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the 'solution-precipitationo step postulated when the carrier phase is liquid3 although in the nickel tungsten case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in mi-crostructures at the temperatures under consideration. In the present work, new data for nickel-coated tungsten powder are offered in support of the proposed mechanism, and a more explicit study of the second stage of densification is presented. Concurrently, the sintering kinetics of these coated powders are compared to Ni-W powder made by coreduction of oxides. In this way the present work can be compared to earlier results in nickel activated sintering of tungsten in which the coreduction process was emplyed. The ultimate utility of such an activated sintering process will be determined to some extent by the mechanical and physical properties of the final prod-

Jan 1, 1962

By AIME AIME

THE Petroleum Division will hold two meetings this fall, one on the Coast at Los Angeles, Sept. 29, with the technical sessions in the assembly room of the California Oil and Gas Association and a banquet Friday evening at the Richfield Cafe atop the Richfield building; the other in the Southwest, at Dallas, Texas, Oct. 6 and 7, with the Baker Hotel as headquarters. Dr. Frederick M. Becket, President of the Institute, and A. B. Parsons, Secretary, will attend both meetings. Arrangements for the meetings are not yet complete but the respective local committees, working in close touch with the officials of the Division are rapidly shaping up the programs and other detail.

Jan 1, 1933

By Albert J. Phillips

SEVERAL important changes have been' made during 1933 in the compilation and distribution of technical literature to those interested in nonferrous physical metallurgy. The Institute of Metals, of Great Britain, announced that preprints of all its papers would be distributed monthly to all members in combination with their bulletin of abstracts. The A.I.M.E. has announced that it will distribute to all members of the Institute of Metals and Iron and Steel Divisions a monthly bulletin entitled Metals, which will carry preprints of all publications of interest to the members of these two divisions. The American Society for Steel Treating has declared its intention to change its name to the American Society for Metals in order to indicate the broader scope of its activities. The abstract service of Metals and Alloys has been improved and expanded, covering practically the entire field of metallurgical literature. These changes and innovations now provide unparalleled reference service entirely in the English language.

Jan 1, 1934

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.' Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph' (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,' have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

(The following list contains the names of those members of the Institute of whose connection with military service. we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ADAMS, HENRY, Major, Assistant to Department Engineer, North-eastern Dept. ALINE, P. A., Co. C, 316th Supply Trains. * Low-cost cottage construction in America; a study based on the housing collection in the Harvard Social Museum, by Winthrop A. Hamlin. Cambridge, Mass., Harvard University, 1917. (Publications of the Department of Social Ethics, No. 7.) 30 pp., 4 charts. Illus.

Jan 5, 1918

Granduc lies near the Alaskan border in British Columbia, about 600 miles (960 km) north of Vancouver. Prospecting in the area must take place in the short summer months of fog and rain because the winter is bitter cold, with snowfall up to 960 inches (24.4 m) accompanied by avalanches. Despite these difficulties, the mineral ized area was discovered in the 1920's. By 1956, Newmont Mining Corporation had developed mineable ore reserves estimated at 32,500,000 tons of 1.93% copper. Newmont and ASARCO, in a joint venture, then began development of the ore body, which was partially covered by glaciers. It was apparent a concentrator could not be built at the mine site where overland access was impossible due to the weather conditions and the terrain. Years of engineering studies of all possible access routes finally dictated the driving of an 11 mi long (17.6 km) tunnel passing under three glaciers and three mountain ranges to the nearest feasible concentrator site at Tide Lake. Even then, a mountain road subject to an average snowfall of 800 in. (20. 3 m) had to be built 32 mi (51 krn) from the concentrator through Alaska to Stewart, British Columbia, the nearest port. At Stewart, which is located at the head of a fjord 120 mi (192 krn) from the Pacific Odean, a fully equipped marine terminal was built. The tunnel, the lifeline between mine and mill, was to be driven from both ends; however, in 1965, an avalanche occurred at the Leduc portal, killing 26 crew members and wrecking much of the camp. The tunnel was then driven from one heading adjacent to the concentrator site at Tide Lake, a distance of 53,744 ft (16,381 m) to a point under the ore body. The remote location, type of terrain, and bad weather made supply of crews, equipment, and construction materials difficult; but in spite of these extremely adverse conditions, the tunnel crews set many world records. Mineralization throughout the ore zone is generally uniform in grade and composition and is primarily chalcopyrite and pyrrhotite associated with pyrite. Mining is mainly by sublevel caving. After blasting, rubber-tired load-and-haul equipment moves from level to level by means of an internal connecting ramp system on a 15% slope. At the gathering haulage level, 15-ton bottom-dump cars deliver the ore to a 600-ton pocket equipped with a Hudson "Rock-Flo" dump. The bottom of the ore pocket forms the feed chute to the primary

Jan 1, 1978

By J. M. Sands

Production of oil in Oklahoma during 1927 amounted to 273,256,900 bbl. (Table l), an increase of nearly 100,000,000 bbl. over the previous year. All of the major fields declined with the exception of those of the Seminole district which produced 136,105,000 bbl., almost one-half of the total production of the state. Because of this large new production, most of the development in the state during the year took place in that district. The Seminole City pool located in T.-9-N., R.-6-E., was the first of these pools to be developed. The Indian Territory Illuminating Oil Co. brought in the first well in this field in March, 1926, for 1100 bbl. This well is located in Sec. 24-T.-9-N., R-6-E., and produced from the Hunton lime reached at depth of 3900 ft. The first Wilcox production was developed by the Independent Oil & Gas Co. and R. S. Garland in Sec. 26, T.-9-N, R-6-E. This well was being drilled for production in the Hunton lime but was dry in this horizon and was deepened to the Wilcox sand in July, 1926, and at the total depth of 4069 ft. developed a maximum production of 8000 bbl. daily. It held up in wonderful manner and was the cause of not only the development of this pool but the prospecting of the whole district for the Wilcox sand. This led to the discovery of the other major pools in that district. Seminole City pool reached a peak production of 264,500 bbl. on February 22, 1927, and slowly declined so that by December it had a daily average of 56,200 bbl. from 321 wells. The second pool in this district to be discovered was the Searight pool which was discovered by F. J. Searight et al. in Sec. 33, T-10, R-6, in April, 1926. The first well was drilled to the Hunton lime encountered at 4115 ft., and came in for 1300 bbl. daily. During August, 1926, the second well was drilled on the same farm through the Hunton lime to the Wilcox sand which was encountered at 4360 ft. It came in for an initial production of 4000 bbl. daily. This started active drilling in this field for the Wilcox sand. The field had a peak production of 40,621 bbl. on June 15, 1927, and declined to a daily average of 22,300 bbl. from 73 wells during December.

Jan 1, 1928

By Nicholas J. Grant, John S. Benjamin, Bill C. Giessen

In the course of a study of hard particle-duc tile binder composite alloys, interest arose in the nature of the products of the reaction between the inter metallic compound NiAl and the binder niobium. No published information was then available. A program to

Jan 1, 1967