Search Documents

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By Jack F. Harang, P. B. Leavenworth

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company&apos;s No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation&apos;s No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company&apos;s No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By P. B. Leavenworth, Jack F. Harang

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company&apos;s No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation&apos;s No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company&apos;s No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if&apos; the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.&apos;-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By M. G. Driessen, H. E. Criner

Possible applications of cyclone thickeners for: (1) clarification of the washery water and, (2) recovery of fine coal from the plant bleed. The paper shows: (1) that it is possible to remove all particles including the very finest, from the circulating water, thus obtaining a closed water system and, (2) that reduction of the ash content of the solids of the plant bleed is feasible by means of cyclone thickeners. Performance data for different size cyclones is given in the form of graphs.

Jan 1, 1950

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation&apos;s trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors&apos; opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932

By R. F. Rolsten

VAN Arkel 1 prepared ductile tantalum by the thermal decompoiition of tantalum pentachloride on a resistively heated wire (2000° C) in an evacuated bulb maintained at 100°C. Burgers and Basart2&apos;3 observed the formation of a mixture of tantalum carbide and free metal when a carbon deposition base was used. campbel14 suggested the thermal decomposition of the iodide if a lower decomposition tem- perature was desired. To date, the details for preparing high-purity iodide tantalum have not been disclosed. EXPERIMENTAL The tantalum to be purified was symmetrically placed around the clear quartz deposition surface centrally located within a 64 mm cylindrical Vycor bulb. The deposition vessel usually employed5 was modified6 by incorporating a reentrant fin,mer in place of the customary metal filament in the head

Jan 1, 1960

By Ogden Malin

IN conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructure of several compositions under various conditions of working were examined in an effort to establish this as a fact.

Jan 1, 1932

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby&apos;s pole mechanism are discussed in detail by Venables.&apos; In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By D. Geoffry Minnes

Nepheline syenite is a silica deficient crystalline rock consisting of albite and microcline feldspars and nepheline, together with varying but small amounts of mafic silicates and other accessory minerals. Nepheline-bearing rocks are widely distributed around the world but only in Canada, Norway, the Union of Soviet Socialist Republics, and the United States are deposits worked commercially. Because of its low melting point and fluxing ability, nepheline syenite was investigated in the early 1900s by many students of glass and ceramics. Although the nepheline syenite deposits in Methuen Township, Ont., Canada, were discovered as early as 1897 it wasn&apos;t until 1935 that the first mill was erected to produce nepheline syenite products. In Canada, nepheline syenite deposits are worked by Indusmin Ltd. and International Minerals and Chemical Corp. (Canada) Ltd. who have combined production capacity in excess of 1800 tpd. Between 1935 and 1972 seven million tons valued at $78 million were produced from the Methuen Township deposits. In Norway, the Norsk Nefelin Div. of Elkem Spigerverket has produced nepheline syenite from a deposit on Stjernoy Island in western Finnmark since early 1960. Between 1961 and 1972 the company produced 930,000 mt with an estimated value of $17 million. Nepheline syenite has been under investigation in the Union of Soviet Socialist Republics (USSR) since at least 1928. In 1951 the first commercial alumina works was brought on stream at Volkhov, near Leningrad, utilizing nepheline concentrates from the Kola peninsula as mill feed. Since then two others have been completed and more are planned. Large quantities of portland cement, sodium carbonate, and potassium carbonate are produced in conjunction with the alumina. In the United States, nepheline syenite has been produced for many years from deposits in central Arkansas by the Big Rock Stone and Materials Co. for construction aggregates and, since 1947, for roofing granules by the 3M Co. Chap. 16 on "Feldspar, Nepheline Syenite, and Aplite" in the 3rd ed. of Industrial Minerals and Rocks (Castle, and Gillson, 1960) and Nepheline Syenite Deposits of Southern Ontario (Hewitt, 1960) contain excellent accounts of earlier commercial development of nepheline syenite as a glass and ceramic material. Therefore this chapter deals mostly with the period since 1960 and with matters not previously reported in detail. An English monograph on Nepheline-Syenite and Phonolite (Allen et al., 1968) is a complete current survey of nepheline syenite which, with its very complete list of references. is an excellent source book. End Uses Nepheline syenite from the Canadian and Norwegian producers finds use primarily in the manufacture of glass and ceramics. One producer also makes several grades of nepheline syenite that are useful as extender pigments and fillers in paint, plastics, and rubber. In the Soviet Union nepheline is used in increasing quantities in the manufacture of alumina, alkali carbonates, and portland cement and to a lesser degree it is used in the manufacture of colored container glass.

Jan 1, 1975

By H. A. Domian, H. Biloni, G. F. Bolling

Jan 1, 1965

By NONE N

Jan 1, 1963