Search Documents

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the' second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson' argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks' and to the precipitation of second phase particles,2'3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these '(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970

By Thomas T., Read

T HE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established,, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently , attempted to make a much too simple correlation between mineral -discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail.

Jan 1, 1941

By N. H. Mannakee

SINCE the publication of the paper of Mr. Scholz, The Effect of Humidity on Mine-Explosions,' I have undertaken a study of the meager available data of barometric and temperature conditions it times of mine-explosions, and have arranged these data in a manner which may be of interest to other students of mine-explosions. This study covers the period from 1898 to 1909, during which an ever-increasing percentage of collieries has been ventilated by fans giving air-currents of high efficiency. Previous to 1898 this percentage was smaller than at any time since. The vari¬ous States have become, from time to time, more exacting in their demands upon poorly-ventilated mines. This general im¬provement in ventilation throughout the Appalachian field has undoubtedly brought about a condition which is annually the cause; .or a very important attendant, of the high percentage of fatalities in mine-explosions, through the daily passage of from hundreds to thousands of gallons of water, invisibly suspended in the air, carried out of the mines by the ventilating-currents during the existence of certain temperature- and humidity-conditions. There is a wide-spread opinion that these conditions exist from November 1 to March 31; but it is more likely that they have a much wider range, which varies from year to year. Certain years show an increase or decrease of rain-fall from the mean ; the daily temperature may fall far below or rise far above the mean established by a record of a period of years; and the daily humidity varies likewise. If mine-explosions are influenced by a lack of moisture in the mines, certainly it may be expected that the influence will be felt at times when the

Nov 1, 1909

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Abstract-Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environment control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m, (24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1- ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky Fluorspar mining district, and late Paleozoic, erosional unconformities in northeastern Kentucky.

Jan 4, 1978

By Michael Hoch, Michel Desjardins

The isothermal section of the Mo-Ti-Zr-0 system at 1500°C was investigated using X- ray diffraction and mefallographic techniques. Up to 66.7 at. pct 0, the system contains ten four -phase regions. Isopleths at 10, 30, 45, 55, and 60 at. pct 0 were constructed. THE purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of molybdenum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct o. PREVIOUS INVESTIGATIONS The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen' and Levin, McMurdie, and Hall.3 Farrar, Stone, and Margolin studied the titanium-rich corner of the Ti-Mo-0 ternary. MATERIALS The titanium powder, 99.6 pct pure, the zirconium dioxide, and the molybdenum powder were supplied by the Fairmont Chemical Co. The zirconium powder,

Jan 1, 1962

We would like to thank Mr. Mandolesi for his informative paper on rails from strand cast steel. The chemical and structural properties of the strand cast steel were of particular interest to us. We would like to supplement his excellent report with some of Inland's findings from our Caster with submerged nozzles and strands reduced in line from 7" x 7" to 5-5/8" square cross section. Inland has conducted extensive segregation studies on AISI 1049 steel - Fine Grain 0.50% carbon and 0.75% manganese. Based on approximately 80 heats, our normal segregation pattern results in analyses of .49% carbon in the center, and 0.50% carbon at the midway and edge position. The sulfur analysis averages .025% in the center, .027% midway, and .026% at the edge. Note the slight negative segregation between the center and midway position. This steel, being lower carbon and probably cast nearer the liquidus, resulted in less segregation than the 0.80% carbon rail steel.

Jan 1, 1972

By P. R. Sperry

In an investigation of the decomposition of the solid solution in a cold worked high-purity aluminum alloy containing 7 pct Mg, aged at temperatures from 30o to 82°C, the nucleating sites at the earliest stages of precipitation were observed to be of two types. Nucleation occurred at the high angle grain boundaries both when the alloy was initially cold worked and when solution annealed. Nucleation also occurred at certain unique deformation markings which began to appear in abundance at approximately 30 pct reduction in thickness by cold rolling. These deformation markings were identified as deformation (kink) bands rather than as the usually assumed "slip planes." Zn material that was cold rolled 15 pct, only the grain boundary Fig. 2—A1-7 pct Mg alloy, cold worked 60 pct and heated at 230° C for 5 min. Etched with Perryman's reagent. X500. Reduced approximately 25 pct for reproduction. (a) Bright field illumination, precipitate deeply pitted. (b) Phase contrast, showing slip markings.

Jan 1, 1962

By Rodney P. Smith

THE solubility of columbium nitride in ? iron has been determined for the temperature range 1191o to 1336°C from the nitrogen content and metallogra-phic examination of a series of Fe-Nb alloys.* (0.0 to 0.92 pct Nb) equilibrated with a purified gas mixture of 1 pct hydrogen in nitrogen. The method is the same as that used by Darken, Smith, and Filer' to determine the solubility of aluminum nitride in y iron. The variation in the furnace temperature during an equilibration period was about ± 2.0°C. Each sample was approximately 1/2 in. wide, 2 in. long, and 1/16 in. thick. A time series at 1200°C using samples of highest columbium content indicated that one day was sufficient for equilibrium; however, to be on the safe side all samples were left in the furnace for either two or three days. Afterequilibration, the samples were brought to room temperature by quenching in water. The experimental results are shown in Fig. 1. To be in accord with the values reported by Wriedt and Gonzalez2 and the temperature coefficient of our results at higher temperatures, the nitrogen content of iron at 1191oC is assumed to be slightly lower than our experimental value. Our data for the single-phase regions are not sufficiently accurate to establish an interaction coefficient for nitrogen in these alloys. However, the change in nitrogen content with change in alloy content for a number of systems (Fe-N-A1;3,1 Fe-N-Ni;372 Fe-N-Si.3949 Fe-N-V;3,5 Fe-N-Cr;3,6 Fe-N-Mo3,7) has practically the same value for the liquid alloy at a temperature near 1600°C as for the solid alloy at temperatures near 1200oC when the alloy content is below a few percent. On this basis the lines through the single-phase regions have been drawn with a slope corresponding to an increase in nitrogen of 0.0013 pct per 0.1 pct Nb.3 The straight lines through the two-phase regions were drawn with a slope corresponding to a one-to-one atom ratio of nitrogen to columbium in the nitride. The X-ray

Jan 1, 1962

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth's crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth's surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By L. C. Brown, J. S. Kirkaldy

Measurements have been made of carbon diffuswn in the five ternary austenites Fe-C-Si, Fe-C-Ni, Fe-C-Co, Fe-C-Mn, and Fe-C-Cr in which the carbon (component 1) diffuses through interstitial sites and the ternary addition (component 2) diffuses substitutionally. Values of the diffusion-coefficient ratio, D12/D11 were determined for each system with finite couples using the transient equilibrium method. The effect of temperature and of concentrations of both the carbon and substitutional component upon D12/D was examined and was found to agree with the theoretical predictions. It is concluded that within an experimental uncertainty of 10 to 15 pct, it is possible to calculate the ratio D12/D11 from purely thermody-namic data. Difficulties of measuring the other off-diagonal coefficient, 4,, are discussed. Any quantitative attack on the fundamentals of the hardenability problem in steel must begin with the multicomponent diffusion formalism and with the accumulation of data pertaining thereto. In a recent paper Kirkaldy and purdy 1 employed the formalism derived from irreversible thermodynamics to treat the problem of diffusion in ternary austenites. In the latter solutions, carbon diffuses through interstitial sites and the substitutional component diffuses through the lattice. Examples were given of diffusion in the systems Fe-Mn-C and Fe-Si-C. In the present paper, we present new results on and discuss their agreement with the thermody-namic theory. Since the theory has been slightly modified from the original presentation of Kirkaldy and Purdy, their results on Fe-Si-C and Fe-Mn-C have been recalculated and are presented here for completeness. The flux of the interstitial component with respect to a fixed lattice framework can be written as a linear expansion in the independent concentration gradients, where X1 and X2 are the independent thermody-namic forces in the lattice fixed frame of reference. These forces can be obtained from the general statement for forces in a volume fixed frame2 if the partial molar volume of carbon atoms is set equal to zero and that of the substitutional component 2 is set equal to unity, viz where the are the chemical potentials and the N's are mole fractions. Introducing into [3] and [4] the function If, as suggested by statistical arguments, the off-diagonal interaction L12 is sufficiently small, [6] reduces to i.e., the coefficient ratio becomes purely thermo-dynamic. The activity of components 1 and 2 in a dilute ternary system (standard state at infinite dilution) may be represented by the expansion3

Jan 1, 1964

By Charles R. Austiuon, Carll H. Samans

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Carll H. Samans, Charles R. Austiuon

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By FRED T. WILLIANS

INTRODUCTION. THE Park City mining-district is distinctively a camp of few properties, 5,000 acres, or one-third of the entire district, being under the management of but three companies. As a rule, the ore-bodies lie deep, with no outcrop, except where erosion has formed the deeper canyons and gulches. Ontario canyon exposed the famous Ontario ledge, and Woodside gulch showed the first ore of the Silver King Coalition mine. The Quincy ore-bodies were first brought to light in upper Empire canyon, and Thaynes canyon was instrumental in aiding the prospector during the early days of the camp. There are 22 shafts which have reached a depth of at least 500 ft., ten a depth of 1,000 ft., five a depth of 1,300 ft., and two a depth of 2,000 ft. The amount of lateral development has been proportionally extensive, including six long tunnels, four of which are in 3 miles, with a fifth now being driven. The Ontario lower drain-tunnel is now more than 4 miles long. The formations are sedimentary, dipping about 30° NW. and N., and traversed by many fissures, dikes, and faults. The principal ore-bodies are found associated either with the contact of the basal Ontario quartzite and the overlying limes, or on a quartzite stratum within the limes, or in the fissures, or along some of the porphyry dikes. The district covers the intersection of the Uintah and Wasatch ranges, which explains the existence of large folds and faults, and fissures of great length, width, and depth. In a general way, the geology of the district consists of a basal quartzite dome, which has been exposed by erosion at the Ontario property. The Ontario fissure lies entirely within this formation. Flanking this dome on the west, north, and east lie

Jun 1, 1911

By Jack C. Haptonstall

Abstract-Minas de San Luis, S.A. operates the old Tayoltita mine located in the Sierra Madre Occidental in Durango, Mexico. Yearly production is 55 000 kg (1.7 million troy ox) of silver and 1000 kg (31,000 troy ox) of gold from milling 165 000 t/y (181,900 stpy) obtained from fissure veins. A 4.4 km (2.75 miles) adit, to intersect the veins below existing workings, was completed in 1974. The adit and ancillary projects facilitated extensive mechanization of the mine, ramp development of it, integration of duplicate facilities and elimination of obsolete facilities. It provided a deep-level access for exploration and development of the veins, and resulted in a 25% increase in production with the same labor force. The cost of the in-house financed project was $3.4 million.

Jan 2, 1978

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after it has been pulverized to pigmentary size. The current world production of iron oxide pig¬ments is estimated by the author to be between 450,000 and 550,000 tons based on 1969 data. The fact that highly colored natural deposits of iron ore are found throughout the world ac¬counts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments pro¬duced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970). Nomenclature With the increasing importance of the syn¬thetic iron oxides it is necessary to make a distinction between the natural or mineral pig¬ments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a com¬mercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pig¬ments. Natural pigment ore sources are se¬lected for their special physical-chemical prop¬erties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pig¬mentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1975

By George Ashley

IT has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. TABLE 1.-Pittsburgh Coal Bed to Dec. 31, 1934 Estimated Recov- State Thousands of ( Value erable Reserves Tons Mined (1935), Thousands of Tons Pennsylvania 3,144,000 $4,922,000 7,500,000 Ohio 493,391 843,699 3,000,000 West Virginia 650,000 1,027,000 5,500,000 Maryland 183,224 254,681 20,000 Totals 4,470,615 $7,047,380 16,020,000 PRODUCTION AND VALUE In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately.

Jan 1, 1936