Search Documents

By Albert J. McIntosh

In discussing the petroleum products situation the first thing that comes to mind is "what is happening to gasoline." Is the consumption increasing? How is the export market? What about imports? Are stocks on hand too high? Have we produced too much? This paper will attempt to answer these questions. Consumption of gasoline (motor fuel) in the United States in spite of the depression and the chaotic conditions of many industries has increased during 1931 about 2 per cent over 1930. This favorable factor was offset by a severe contraction in exports, which fell off about 30 per cent from 1930. This drop in exports was so large that very little more export business was done than in 1926 or 1927. Taking all demand combined, there was a decrease from the peak year of 1930 of nearly 11,000,000 bbl., amounting to slightly over 2 per cent. The units of the industry, though, should have expected some decrease and governed themselves accordingly. Let us see what they did. They reduced imports over 3,000,000 bbl., which helped. Production was cut 3,000,000 bbl., but this was not enough, so that stocks increased 1,800,000 bbl. whereas during the previous year stocks were reduced 2,500,000 bbl. It is apparent, therefore, that something was done to keep the industry in balance in regard to gasoline, but not enough. If the year had ended on Sept. 30, we could have said that production had been cut 19,000,000 bbl. and stocks had been reduced from the previous year, but the excessive production during the last three months of the year changed everything. It is a strange thing and worthy of note that the price of gasoline fell to its lowest levels when apparently the greatest improvement was being made, and that during the last quarter of the year prices started to improve, when, in spite of an improvement in total demand which approximated 1930, an excessive production caused an uneconomic condition to set in. Stocks on hand on Dec. 31 were unquestionably too high, possibly 10,000,000 bbl. more than was needed for a strong condition to obtain. It seems almost unbelievable that the industry would continue to produce

Jan 1, 1932

I HAVE now traversed for you in the small and fragile bark of my writing all the shores of the deep and spacious sea embracing the uses of material fires, drawn on by my own desire to enrich you with more learning and with the procedures of these things, as much as to satisfy your demands. Having through the grace of God arrived at the appointed end of my voyage and neither knowing nor perceiving a way of going farther, I had decided to furl the [167] sails and cast die heavy anchors into the water in order to enjoy in tranquillity respite from my sailing, when I was warned by my pilot that before I could disembark I should turn my glance backward and reexamine my work in detail to see if there were any part that had by chance remained undescribed in the obscurity of silence. When I did this there immediately appeared in my mind's eye the many sublimates and smoky tinctures that had been made by the burning and most powerful fire of love. I need not say that I knew of it in far-off countries or from the knowledge of others, but I knew it in my own breast and as my very own and can therefore surely esteem it as hotter than all the other fires that the world calls by that name. Although today its sparks and living flames are spent because of my cold and hoary season, nevertheless it is true that the memory of acts of love of long ago still remains with some smoke and warmth. Therefore, since in this work of mine I wish to describe for you the effects and powers of fires, I should logically have spoken of this before any of the others, because of its actual nearness and the great acquaintance I had with it. But since I have had the glance of my intentions directed at distant things, I have behaved as one does who does not see where he places his feet because he is looking at the sky, or as one who thinks about the affairs of others and forgets his own. But now I do not wish to pass over this thing and I wish to correct my error, particularly in order to provide a happier ending to my written work than by remaining among the horrible uproar of guns, powder, and saltpeter, which would be a harsher ending than speaking of love. Never-

Jan 1, 1942

By Walter Miller

AFter a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity—more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser ones) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture. The difficulty in presenting a review of engineering progress in petroleum refining during 1942 is that there is so little one is free to say about so much which has been and is being accomplished. At the opening of 1942 the program was to increase the then existing capacity of 50,000 bbl. a day of aviation gasoline to over 150,000 bbl. daily by building new plants at an estimated installation cost of $150,000,000. Later in the year. after the announcement by President Roosevelt of a large increase in the program for war-plane building, additional contracts were made between the Reconstruction Finance Corporation and rehers to raise the capacity to 250,000 bbl. per day. The greatly increased scope of the war activities in all parts of the world, the obligation of the United States as the arsenal of the United Nations, and the greater importance and use of bomber, transport, and cargo planes will undoubtedly bring about plans and installations for a further increase in production of aviation gasoline over the present announced plan. In this connection, Jesse Jones, Reconstruction Finance Corporation Chairman, announced that as of Oct. 31 the R.F.C. had through its subsidiary Defense Plant Corporation entered into contracts for the construction, expansion, or equipping of 28 plants to increase 100-octane aviation gasoline production, but gave no data on 'capacity involved or completion dates. His list did not, of course, include a number of existing plants, and some installations being made by companies who are themselves financing the construction. Production from existing operating installations was materially increased in a number of instances as a result of pooling knowledge of improvements in operation and also by the exchange of Components going into 100-octane blend to enable greater quantities of aviation gasoline to be produced from the over-

Jan 1, 1943

By Richard D. Mills

Throughout the mining industry, many companies perform sophisticated business and financial analyses of proposed capital investments. However, once the project is approved, it is never reevaluated. At best, there is an attempt to control capital costs and minimize overruns. The post-installation appraisal, a formalized review of investment performance, may prove helpful. Typical Project Review A typical capital investment is approved after business and financial benefits have been reviewed with management.* The financial data shown to management often include a net income statement, cash flow analysis and summary economic data similar to those shown in Table 1 overleaf. These financials report the expected impact of the project on the corporation financial statements. This project is a rudimentary example of a capital investment decision. An actual project would undergo a more sophisticated analysis incorporating depletion benefits, deferred taxes and a detailed cost breakdown. The example project has several financial benefits that could result in management approval. For example, it provides an immediate net income benefit to the company, generates positive cash flows every year of the project life and has a discounted cash flow rate of return of 25 percent. However, it also has the disadvantage of a long payback period. A sensitivity analysis would show which areas of the analysis have the greatest impacts on profitability. Post-Installation Program Objectives The post-installation appraisal goes beyond the analysis shown in Table 1 by comparing actual results to those projected in the original economic analysis. The post-installation program has three primary objectives: 1. To provide a periodic performance review of major spending programs. 2. To review decision-making and evaluation procedures. 3. To provide a means of controlling individual project investments. The first major function of the post-installation program is the periodic review of actual performance of projects and investment programs, identifying those factors which proved critical to the health of investments. This review will serve to keep management abreast of progress, provide a comparison of actual performance against expectations, and provide valuable information that can be used for improving future economics. The second major function of the program is to perform a continuous review of the decision-making process. This includes testing of evaluation procedures, forecasting techniques, and logic used in making decisions. An information system should be set up whereby original evaluations and historical performance data gathered under the appraisal program are documented for use by evaluators and management when assessing past and future investment proposals. Such data should be particularly useful in evaluating new and developing types of operations and in activities where companies repeatedly reinvest. The primary purpose of this feedback system is to sharpen estimates to assure that they are realistic and attainable. The appraisal program also provides assurance that consistent evaluation procedures are being used throughout a company, leading to improved procedures

Jan 1, 1985

By John F. Blandy

With the Report of Mining Statistics, for the year 1872, there was published a geological map of the United States and Territories. This is, I believe, the only map which represents the geology of Arizona, and is, as far as my observations go, correct. It is, however, on so small a scale as to be of little practical value to the miner. I know of no other maps, even of localities, of this Territory. The topographical maps are also on so small a scale as not even to serve as guides from place to place; the largest, that of Eckhoff and Ricker, being only 30 by 30 inches to represent a territory of 135,000 square miles. For these reasons, it makes it exceedingly difficult to describe the various mining centres in an intelligent manner, and equally so to examine such a hilly country as it is intended to describe in this paper. When I first came into this Territory I soon realized the troubles I had to encounter in trying to form an opinion, or even to get the needed information on the geological contour. I have, therefore, labored as best I could to get a topographical diagram of the section of country represented by the map which accompanies this paper.* The lines run by the Land Department up the valleys of the Aqua Frio, and those west of the Hassayampa, and connected east and west to the north of Prescott, enabled me to inclose correctly the space covered by the Bradshaw and Sierra Prieta mountain groups, but the territory covered by these mountains, and the most difficult part, I have had to fill up as best I could. I have met with such success as to meet the approbation of those most familiar with the country, and, with the map in hand, any one would he able to cross it in any direction. As there has not been a single line of survey made across it, this has been no small undertaking, and I have had to depend upon sights from prominent points with the pocket-compass, or, in the absence of that, to make observations, with watch in hand, and guess as near as possible the meridian direction. Rut one main wagon-road passes through the district, that from Prescott to the Peck mine.

Jan 1, 1883

By Barnabus Bryan

THE normal statistics of supply and demand of petroleum and its products have little more than local influence on the market movements of oil securities. The two major reasons for this condition might be called the technique of production and the technique of refining. The speed of improvement in each and the complete lack of control of their, inter-relation have resulted in overproduction of both crude oil and gasoline in the face of immense in-crease in demand. The trouble with oil securities has been that of the mushroom radio companies, where too frequent changes have killed the possibility of profits. It is a case of too much efficiency. During the past ten years there has been continual talk of wasting reserves of crude oil. This has been based on "present methods of production." Yet the methods of ten years ago in the oil industry are as antiquated today as the kerosene lamp.. The fear of famine has transformed the industry. The refiner, through the cracking process, has doubled the gaso-line output from a barrel of crude oil, thus doubling reserves and changing a current undersupply into oversupply. When the automobile driver desires he can again double reserves and transform want into abundance by demanding an automobile which will deliver twice as many miles per gallon of gasoline. Entirely apart from refining and in complete dis-regard for its needs, the oil producer has forged ahead at a pace too rapid for his own good. The science of geology has developed with experience and' lavish expenditure into a constant danger to profits in the production of oil. Two and one-half per ;cent of the producing wells in the United States are yielding one-half of the oil, while their flush production is used as an excuse to force down the price of crude oil until 200,000 wells must be abandoned or produce at a loss. The fabulous yield of the new high-pres-sure fields enables the fortunate owners to make a profit regardless of the price of oil. Such a condi-tion is unhealthy from the standpoint of oil itself and as a national policy. It is manifestly absurd to suppose that such a condition can endure for a gen-eration. There will come a day when the sequence of discovery will be temporarily broken, and at that time the consumer will be forced to pay heavy interest on the foolhardy policy of today.

Jan 6, 1927

By Walter Miller

AFter a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity—more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser ones) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture. The difficulty in presenting a review of engineering progress in petroleum refining during 1942 is that there is so little one is free to say about so much which has been and is being accomplished. At the opening of 1942 the program was to increase the then existing capacity of 50,000 bbl. a day of aviation gasoline to over 150,000 bbl. daily by building new plants at an estimated installation cost of $150,000,000. Later in the year. after the announcement by President Roosevelt of a large increase in the program for war-plane building, additional contracts were made between the Reconstruction Finance Corporation and rehers to raise the capacity to 250,000 bbl. per day. The greatly increased scope of the war activities in all parts of the world, the obligation of the United States as the arsenal of the United Nations, and the greater importance and use of bomber, transport, and cargo planes will undoubtedly bring about plans and installations for a further increase in production of aviation gasoline over the present announced plan. In this connection, Jesse Jones, Reconstruction Finance Corporation Chairman, announced that as of Oct. 31 the R.F.C. had through its subsidiary Defense Plant Corporation entered into contracts for the construction, expansion, or equipping of 28 plants to increase 100-octane aviation gasoline production, but gave no data on 'capacity involved or completion dates. His list did not, of course, include a number of existing plants, and some installations being made by companies who are themselves financing the construction. Production from existing operating installations was materially increased in a number of instances as a result of pooling knowledge of improvements in operation and also by the exchange of Components going into 100-octane blend to enable greater quantities of aviation gasoline to be produced from the over-

Jan 1, 1943

By L. Casagrande, C. O. Brawner, D. L. Pentz, B. Kennedy, E. Hoek, H. Q. Golder, K. Barron

H. L. HAMMERSLEY, B. C. Dept. of Mines. I would like to ask Mr. Brawner if the direction that he measured in the boreholes with the camera was referenced to magnetic north? MR. BRAWNER. Yes, it was. However, there is one problem that you may encounter if the ore body is magnetic; the borehole compass will give erroneous results. Three procedures are available to overcome this. The first one involves the use of a gyro compass instead of a magnetic compass. The second technique developed by Christiansen in Salt Lake City, is to orient the core with the use of scribing knives. The third method is to remove the compass needle and place a steel ball in the compass case. The hole must be drilled at a slight angle off the vertical. The location of the steel ball, which will roll to the underside of the hole is photographed. A borehole directional survey is then made, from which the bearing of the steel ball relative to the axis of the compass can be determined. The joint orientation is then related to this bearing at all depths. J. ROBINSON, B. C. Dept. of Mines. It was stated this morning that there have been some recent developments that give us the ability to drill horizontal drainage holes and install drainage pipes more cheaply than in the past. Would Mr. Brawner tell us some of the new developments and methods of installing these horizontal drain holes? MR. BRAWNER There are two zones in which you may be concerned about installing drains; the first is in the overburden soil, the second is in the rock. Each area requires a different installation method. If the rock is fairly massive and the holes will remain open, the simplest procedure is to use standard air track equipment or a percussion drill. At one of the mines in the Highland Valley, drains up to 300 ft. long have been installed with a percussion drill at a rate of one drain per day. The costs were in the order of $2.30 and $2.40 per foot. If the rock is quite soft, such as in a serpentine, it will be necessary to install a casing in the hole. The least expensive casing that will not deteriorate within the life required should be used. Plastic pipe or black iron pipe are commonly used. In soft rock, it may be necessary to drill with a casing to prevent the col-

Jan 1, 1971

By H. C. Vacher, C. J. Newton

EXTENSIVE investigations in the field of residual strain measurement by X-ray diffraction have been made by Bollenrath, Hauk, and Osswald,1 by Smith and Wood,2'3 by Greenough; by Rosenthal and Norton." and many others. Since X-ray strain measuremeits apply only to those crystals of the test body which are of the proper condition and orientation to diffract and since the residual strains revealed may be accompanied by either body or tex-tural stresses, there has been considerable disagreement among investigators with respect to the validity of conclusions in this field. Although the experi-mentors have employed a variety of loading schemes, surface preparations, and X-ray wave lengths, the observations almost invariably have been made only on the outer surfaces of the specimens. The present note is not to be construed as an exposition of a new method of stress analysis by X-ray strain measurements on sections but as a presentation of some results which point to interesting possibilities for further experiments with sections. The two test rods used in this study were of ingot iron annealed at 910°C. The initial length of the gage section was 2 in. and the diameter was 0.415 in. Cross-sections were cut from the ends of the annealed rods to provide strain-free material. The tensile rod was axially loaded the desired amount in a commercial testing machine. A 1 in. portion of the gage length was cut from the other rod and was subjected to compression in the same machine. Details of this plastic straining of each rod are given in the upper half of Table I. A half-cylinder piece about 1/4 in. long was obtained by making a short longitudinal plane cut containing the axis of the rod near the center of the gage length. From adjacent material a disk about 1/8 in. thick was cut to provide the cross-section specimen. Later another section was cut from this same region with an angle of 30" between the normal to its surface and the axis of the test rod. A cross-section and a longitudinal section were cut from the compression rod in a similar manner. All of these as well as the strain-free cross-sections were mounted in Bakelite and used as specimens for the following X-ray strain measurements. During the course of the study, it became apparent that the condition of the surface of a specimen was a highly critical factor. One of the annealed strain-free specimens as a control was subjected to about 24 hr of polishing with fine alumina, interrupted about every 2 hr for etching with 1 pct nital. Its lattice parameter was determined at intervals from measurements on back-reflection X-ray diffraction patterns, which were calibrated with diffraction from tungsten powder. The parameter gradually approached the value found in the literature for strain-free iron and remained there, within the limits of the experimental error. This determined a long polishing and etching procedure which was adopted for all the specimens and which gave X-ray results from the surfaces believed to be representative of each specimen as a whole. A large number of back-reflection patterns were made with cobalt and chromium radiation, all at normal incidence. Except for some preliminary stationary exposures made to monitor the removal of cold work from the surfaces, each exposure was made with the specimen slowly translating and the film slowly rotating. In appropriate cases a thin layer of a standard metal powder, tungsten with cobalt radiation and silver with chromium, was dusted over a film of vaseline on the surface of the specimen to serve to calibrate the X-ray patterns. After the preliminary work, four films were made,

Jan 1, 1956

By P. R. Sperry, P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the inside texture of highly rolled aluminum and copper strips may be approximately described by four equivalent ideal orientations near (123) [121]. If rolled in reversed passes, the surface texture of copper is also near (123) [121], that of aluminum is (100) [011]. The inside texture of highly rolled brass is (110) [112]. The surface texture is the same, if rolled in reversed passes. The surface texture of all three metals is related to the inside texture, but asymmetrical, if rolled without reversal between passes. MANY previous investigations dealing with the subject of the present work were reviewed by Wassermann.1 Barrett,2 Brick,3 and Richards.' The recent introduction of quantitative methods for pole figure determination by Decker, Asp, and Harker,5 Schulz5 and others made it possible to reinvestigate some of the finer points which the earlier more qualitative photographic methods left undecided. The rolling textures of silver and of 70-30 cartridge brass have been quite consistently characterized by the ideal orientation of (110) parallel to the plane of rolling and [112] parallel to the rolling direction. On the other hand, it has been recognized by several investigators that certain other face-centered cubic metals, such as copper and aluminum, developed rolling textures rather different from that of brass. These textures have been variously described by the following ideal orientations, singly or in combinations with each other: (110 [112]: (112) [111]; (135) [335]; (135) [211], etc. The discrepancies usually have been attributed to the lack of sharpness in the textures and to the attendant difficulty of associating "ideal orientations" with pole figures showing great scatter of orientations. It seemed desirable to investigate by the new quantitative methods to what extent the apparent lack of sharpness may have been brought about by the qualitative methods used previously, rather than by the textures themselves, and to decide, if possible. between the various ideal orientations which have been proposed. Another problem, not satisfactorily settled by earlier investigations. concerns surface textures in rolled metals. For instance, in rolled aluminum the surface texture in some cases appeared to be similar to the texture inside the sheet, whereas in other cases it was reported to be entirely different.' The conditions under which such differences may have arisen, and the possibility of the occurrence of different surface textures in other face-centered cubic metals do not appear to have been examined in detail. The present work was undertaken to investigate the above questions. Some of the results obtained have been described- riefly. Experimental Procedure Specimen Preparation: In the present investigation 2s aluminum, electrolytic tough-pitch copper, and commercial 70-30 brass were used. These materials were available in the form of cold-drawn rods. 1 in. diam for tough-pitch copper and commercial 70-30 brass and 11/2 in. diam for 2s aluminum. The cold-drawn bars were alternately annealed and rolled 30 pct lengthwise in several cycles until a penultimate thickness of 0.500 in. was reached. The intermediate and the penultimate anneals were carried out for 30 min at 380°C with 2s aluminum, and for 30 min at 550°C with 70-30 brass. For tough-pitch copper, the intermediate anneals were 30 min

Jan 1, 1953

By C. Allen Born

INTRODUCTION As the title of this paper suggests, the author does not believe that risk can be managed. Rather, the objective is to identify the risk which will be present in a given venture and assess the level of that risk which is acceptable. More often than not, the risk which is present is subject to little or no modification. After identifying and measuring the risk a corporation will decide to accept it and proceed in such a way that it will be less exposed, or it will decide not to proceed at all. The exercise for a corporation is different only in degree from everyday judgements made by average people in average situations. However, that word "degree" means that it is considerably more complex on the corporate level. There is good reason for the additional complexity of corporate risk evaluation. The variables influencing a company's decision can be more numerous and the penalties for miscalculation much greater than those normally encountered by an individual. It should be understood that no analysis of risk, certainly not one as brief as the following, can do more than touch on some of the high points. Before examining the sorts of risk which affect the development and operation of specific mines, let us consider the broader aspect of the term with which mining companies, and all other business corporations, must deal. Companies must determine their long-term objectives and strategies within the context of a constantly changing world. To plot their direction they must attempt to read the future by seeking answers to questions such as: How will society evolve? Which businesses will thrive? In which of these should we place our emphasis? If a company hopes to be around five or ten years from now it must make the attempt to answer such questions in order to judge the impact of changing patterns in the evolving business environment. Information is available to allow the lessons of the past to be projected on the future. We have data on birth rates, economic booms and busts, patterns of conflict within and between nations, drought and other forces of nature as well as individual events which cannot be predicted, but which over time, do seem to occur in regular cycles. Ultimately the question "where will we be and what will we be doing a decade from now?" must be answered by one or more senior people with responsibility for the company's future. The compilation and interpretation of hard data by competent support staff, can only be used up to a certain point in determining future corporate strategy since there will be alternative possible futures and a high degree of risk will always remain. At this point those elusive qualities of experience, instinct, and - "gut feeling" - become important factors in choosing a long-term corporate direction. The goals of a company have a significant bearing on its attitude towards risk. This in turn dictates the "hurdle rate of return on investment" which a project decision-maker will require. The hurdle rate is the minimum-discount-percentage-rate applied to forecast cash flows to give a present value of zero to the All-Equity-Funded Investor. The feasibility study for a project is a fundamental tool in the management of risk. An experienced team has an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of conservation is built in at all levels of study data and, if the project is technically feasible, the hurdle rate becomes a catch-all measure of risk in a base-case project cash flow.

Jan 1, 1985

By P. M. Aziz, I. Markson, C. S. Barrett

The abnormal after-effect in twisted wires that occurs when untwisting is interrupted by etching con be brought under control and used to study the mechanical properties of thin surface films and how they are effected by reagents and heat treatment. Results are given of studies of oxide films on high purity aluminum. IF a wire is subjected to plastic deformation by torsion and then released, it untwists in the normal after-effect, but under certain circumstances the untwisting is abruptly lessened or reversed by the application of an etchant to the wire.1,2 This abnormal after-effect may occur, for example, if there is a coherent oxide film on the surface of the wire which is removed by the etchant. Following a suggestion of A. H. Cottrell that predicted this effect, it is attributed to dislocations that had piled up beneath the oxide layer and represents the rapid release of residual stresses caused by these dislocations. When the layer is removed, the stress relief may be by escape of piled-up dislocations from the metal, or by an activation of latent sources of dislocations located at the surface, together with rebalancing of elastic stresses to compensate for the loss of stressed material, as in a residual stress analysis determination, these mechanisms acting singly or in combination.' The slower the attack of the reagent, the more gradual is the stress relief and the smaller the change in strain rate when the reagent is applied. A study has been made of the factors that influence the magnitude of the normal and abnormal after-effects with the object of developing techniques suitable for a quantitative investigation of the influence of various surface films on dislocations in wires, and of the rate and extent of the attack on the films by different reagents. It was found that reasonable sensitivity and reproducibility could be achieved if a suitable choice of variables was made and if these variables were held constant through a series of experiments. The method was then applied to a study of oxide films produced and treated in different ways on the surface of high purity aluminum wires, and to a study of the damage to these films caused by various reagents. Experimental Procedure The material used throughout this work was prepared from 99.9968 pct Al. This high purity aluminum was melted, cast into 1/2 in. diameter ingots, and then swaged and drawn without intermediate annealing to 0.040 in. diameter wire. A sketch of the apparatus employed for twisting is shown in Fig. 1. The test wires were mounted into the apparatus by cementing one end of the wire to the beaker and the other to the tube with laboratory wax of high melting point. The length of the wire between the waxed joints was 4.2 & 0.2 cm. Extreme care was taken during mounting to avoid cold-working the wire. The wire was twisted through 335" in 2 to 4 sec by rotating the pinion on the gear box until the vertical post on the rotating table, which was initially touching the horizontal stop, was arrested by the stop. All the tests were conducted with apparatus and reagents at the same temperature (about 25°C). In all tests, except those where the duration of the initial torque was investigated, the torque was applied for a period of 2 min. At the end of this time the table was rotated back a few degrees away from contact with the stop and the wire allowed to untwist. The after-effects were measured by reflecting a beam of light from the mirror shown on the apparatus. After the wire had untwisted for 6 min, a reagent was carefully poured into the beaker and thereby applied to the surface of the wire.. In some tests the liquid in the beaker was removed after a few minutes and replaced by an-

Jan 1, 1954

By J. W. Stewart

The aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1943

By James Norman, Benjamin S. Lindsey

BaritE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the 'more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, II.II per cent SiO², and 2.85 per cent R²O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is scparated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1942

By Nicholas Kowall, K. L. Clark

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Paul A. Beck

IN several recent investigations1 ' considerable evidence was accumulated to show the predominance in various face-centered cubic metals of a certain relative orientation, corresponding to a rotation of 30" to, 40" around a [111] axis, between a matrix with a strong single orientation texture and grains growing in this matrix." This relative orientation was found to occur both in recrystallization and in coarsening, "secondary recrystallization", so that one is inclined to look for an explanation applicable in both cases. The abundance of growing grains in the described orientations proves that suitable "nuclei" are present in the matrix material and that they have the capacity to grow. The scarcity of growing grains in other orientations may be explained in one 'of two ways. Either the number of nuclei or the rate of growth must decrease strongly for orientations deviating from that predominating among the growing grains, Fig. 1. Both the "oriented nucleation" and the "oriented growth" theory found support in the literature. Because the frequency of nuclei as a function of orientation is in most instances not amenable to direct experimental investigation, a definitive decision is difficult to achieve. However, it is now known with great certainty that the rate of boundary migration is strongly dependent on the relative orientation of the two grains meeting at the boundary and that the orientation favored by high boundary mobility closely corresponds to that predominating in most cases of recrystallization and coarsening. Thus, it was found that, in general, the mobility is very low for boundaries between grains of nearly identical orientation, or for coherent twin boundaries. On the other hand, the boundaries between two grains of a relative orientation correspending to a [1111 rotation of 30" to 40" have the highest mobility in face-centered cubic metals. If a large variety of nucleus orientations are produced grow- by means of a highly inhomogeneous local deformation, nuclei close to the above orientation are found to grow fastest.z4 In view of this evidence and of the fact that the preferred orientation relationship is the same in recrystallization and in coarsening, the oriented growth theory appears by far the more promising one. Since the origin of nuclei in primary recrystallization is certainly different from that in coarsening, the occurrence of the same orientation relationship in the two processes would be difficult to explain on the basis of oriented nucleation. other advantages of the oriented growth theory are its capability of accounting for the often observed sharpening of the texture in coarsening, and its suitability for explaining the role in the formation of the ''cube texture,, of the most important variables, such as the degree of rolling, the penultimate grain size, and the time and temperature of the last anneal: No similarly consistent explanation of all these effects has ever been offered in terms of oriented nucleation. An important problem in connection with the oriented growth theory is the following: In the ce-c entered system there are four [111] axes and

Jan 1, 1952

By Louis A. Carapella, Ralph Hultgren

WHEN F. Heusler1 found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.3 All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys" the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intelligently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. PREVIOUS WORK In the original work of F. Heusler1 and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for Cu2MnA1 of I = 443 was early measured. Ross and Grays found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 then reinvestigated the system, confirmed their results,

Jan 1, 1941

By H. E. Stauss

THE time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at 1100°C. better than did 10 per cent iridium- platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at 1100°C. Platinum alloys in their service at high temperatures encounter conditions some- what similar to those that exist in the usual form of the time-to-fracture "l test with steel. This paper is intended primarily to present results obtained by a "time-to- fracture" test under conditions approximating actual service for platinum (at the temperature 1100°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with lo per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., 1000°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,4 using as heating unit a small, horizontal, platinum- wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life-that is, the time-to-fracture-was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fracture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking stresses drop very rapidly to a small frac-

Jan 1, 1943

By Benjamin S. Lindsey, James Norman

BaritE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the 'more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, II.II per cent SiO², and 2.85 per cent R²O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is scparated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1942

By K. L. Clark, Nicholas Kowall

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944