Search Documents

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

Discussion of the paper of L. A. DELANO, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1267 to 1286. L. A. DELANO.-Since this paper was written, our daily mill tonnage has increased, from 2100 tons to 2700 tons a clay. We now use 11,000 lb. of chrome-steel balls of 2 ½ -in. maximum diameter, for an average crushing capacity of 275 tons per 24 hr., this giving a much higher crushing efficiency. I wish to call attention to two typographical errors in my paper as published. On page 1271, Table 1, the screen analysis of ore at the Bonne Terre mill should be stated in inches instead of mesh. - On page 1272, "the rolls average 185 tons per 24 hr., and have shown by test that 250 tons per hour can be maintained" should, of course, read "250 tons per 24 hours." THE CHAIRMAN (0. M. BILHARZ, Miami, Okla.).-Is the increased mill capacity due to improvement in the re-crushing of middlings or to keeping middlings out of circulation and treating them separately? L. A. DELANO.-AS was shown in Mr. Rabling's paper (Bulletin No. 128, p. 1161) the tonnage was raised by about 400 tons by simply changing the arrangement of screen openings in the jig bed and using punched plate instead of woven-wire screen. Then, by adding a ball-mill, we are taking from the jigs a much larger tonnage of middlings than before or as much as the ball-mill will crush. By sending the ball-mill product to tables and flotation, the jig capacity for original ore is increased. CHAIRMAN BILHARZ.-In your opinion, the satisfactory operation of a Hancock jig on a given ore requires adjustment of the length of the different screens and careful selection of screen openings? L. A. DELANO.-I think it does. In order to decide what screen openings to use on the jigs, we did a great deal of experimental work, making screen analyses of the various hutch products, and then hand-sorting the galena, middlings and chat from each size screen to determine the percentage of galena in each. Then adjusting our jig screens, we gradually worked the process up to a very efficient basis. ERNEST GAYFORD, Salt Lake City, Utah.-I would like too ask Mr. Delano whether the work of the Allen cone has been quite as satisfactory as the manufacturers claim for it.

Jan 1, 1918

By A. L. Holley

THOSE who are familiar with working gas furnaces will perhaps admit that the ordinary producer is the least satisfactory feature of the- whole system, chiefly by reason of its great waste of fuel, both above and below the fire. The waste of fuel in cleaning the fire has not, as far as I am aware, been carefully measured ; it has been roughly estimated at various works as averaging twenty per cent. to twenty-five per cent. The coke that falls into the ash-pit is largely mixed, if not stuck together with clinker; when this coke is not recovered and utilized (and where coal is cheap it does not pay to recover it), the waste is certainly as high as above estimated. Cleaning a fire on a grate (especially a fire of dirty coal, like much of our Western coal), by inserting a few temporary grate-bars, then withdrawing the regular grate-bars and letting the whole lower part of the fire tumble into the ash-pit, must necessarily be wasteful of fuel, but it has been found to be the most practical system. The fire under a boiler should be thin, to insure perfect combustion; hence it may be moved from one side to the other, so that .the clinker and ashes may be uncovered and removed. But a producer fire should be so thick that carbonic oxide only shall rise from it ; a thick fire cannot be thus manipulated. In several of the French works the ordinary producer without grates is employed ; the whole body of the fire rests on the floor of the ash-pit. It did not seem to me that less fuel was wasted here than with grates in cleaning fires. The bottom layer of the fire had to be drawn out with hooks, and there was nothing to prevent much coke from coming away with the clinker and ash. A producer shaped like a cupola furnace has many advantages, but if grates are employed the waste of coke in cleaning is not lessened. But the waste at the bottom of the fire is only a part of the waste in the ordinary producer. Mr. Emmerton, chemist to the Joliet Iron and Steel Company, has lately made a number of gas analyses from the producers of that company, worked with impure Illinois

Jan 1, 1880

By Wilbur Nelson

ALL of our accounts of the discovery of copper ore at Ducktown, Tenn., state that the discovery was made in August, 1843, yet it would appear that samples of copper from this district were found by the Spanish explorer, DeSoto, when he wandered into Southern Tennessee, in 1539, in his four years of exploration through the Southern States. The following quotation is taken from his diary: "Towards the north there was a province named Chisca; and that there was a melting of copper, and of another metall of the same colour, save that it was finer, and of a farre more perfect colour, and farre better to the sight, and that they used it not so much, because it was softer. And the selfe same thing was told the governor in Cutifa-Chiqui, where we saw some little hatchets of copper, which were said to have a mixture of gold. But in that part of the country it was not well peopled; and they said there were mountains, which the horses could not passe; and for that cause, the governor would not goe from Cutifa-Chiqui directly quicker." DeSoto sent two of his company to try to find these mines, but after five days' wandering through the mountains they returned, stating that their guides had become lost. Although the Ducktown area may have been known to the ancient Indians, it was not until August, 1843, when a Mr. Lemmons, who was panning for gold on Potato Creek, in the Ducktown basin, found some reddish-brown decomposed rock, which he supposed to be gold, that the copper deposits were actually discovered. His disgust on finding that this yellow metal. was not gold was so great that he did not. try to develop his find. In March, 1847, B. C. Dugger erected an iron forge at this same place, but was unable to work the iron as it contained so much copper that on cooling it would break to pieces. The finding of copper in the iron ore by Mr. Dugger led to further explorations; and in April, of the same year, A. J. Weaver, who was passing through that country, told the people that the black rocks they had dug out were rich copper ore. Mr. Weaver began the first mining in this district.

Jan 10, 1924

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By J. C. Bayles

THE most unsatisfactory occurrences in the experience of a manufacturer are those from which he suffers damage and learns nothing useful. That there are such incidents, and that they occur with annoying frequency, is unfortunately true. An accident which can be understood and explained always carries some consolation with it. However bad the copnsequencee, one finds comfort in reflecting that they might have been worse, and that the knowledge of how to avert a more disastrous calamity from the same cause is worth what it cost. But when an accident occurs, which remains unexplained after anxious days of investigation and sleepless nights of reflection, and which is as liable to occur twice or twenty times, as once, very little satisfaction of any kind can be extracted from it by the most philosophical victim. Three such incidents have come under my notice in one establishment. Fortunately none of them were attended with very serious consequences, as no one was hurt, and the damage to property was slight; but in each instance, loss of life and great destruction were escaped by so narrow a margin as to make them extremely disquieting. I have recorded them in the hope, that from the experience of others maybe gained what my own careful investigations have failed to reach-—satisfactory explanations. The first of these curious occurrences was the bunting of a 16-inch pipe carrying air under a compression of about 1 pound. The pipe was made of light galvanized iron with soldered seams. Into it a rotary fan-blower delivered air, and from it smaller pipes were carried to the furnaces. The blower was run continuously. Neither the main pipe nor its branches had any connection with the gas conduits. Both air- and gas-pipes delivered into the furnaces; but although the gas was under much higher compression than the air, there appeared to be no good reason why, having free escape in case of leakage, it should ever make its way back into the air-pipe. One warm afternoon in June the main air-pipe exploded with great vio-

Jan 1, 1891

By W. L. Zeigler

THE tailing from the gravity concentration plant of the Hecla Mining Co., Gem, Idaho, was former-ly loaded into railroad cars to be used for ballast, highway surfacing material, or concrete work, or dis-posed of by an aerial tramway, which dumped it into another gulch. The tailing averages about 1.2 per cent lead and 0.8 oz. silver to the ton. Further treatment for the recovery of the valuable metals had been investigat-ed several times with results that did not warrant the construction of a retreatment plant; but early in 1925 experimental work was again started with small tests, and later with a 10 tons per day flotation test plant. This showed that the tailing could be ground and treat-ed by flotation at a profit. It was decided to make the new flotation plant an addition to, rather than incor-porate it in the old concentrator, the original capacity of which had been increased many times, the present arrangement being by no means ideal. The old mill buildings were of timber and board contruction, creat-ing more or less fire hazard, so all new construction was made fireproof. Construction work on the new plant was started in the middle of July, 1925, and the plant was placed in operation early in December. The building is of concrete and steel with hollow tile walls, steel sash and corrugated asbestos roofing. The ball-mill floor has for its foundation a cellular reinforced concrete block about 14 ft. deep, extending to cemented river gravel, and the cells filled with tailing to give weight to the block. Overhead, built into the steel frame, is a 5-ton hand-operated traveling crane. With both ball-mills running fully loaded, there is not the slightest trace of vibra-tion in the foundation or building. The flotation floor is of reinforced concrete beam construction and spans Canyon Creek. Adjustable plunger feeders are arranged under the the tailing-bin, which feed by gravity to a 14-in. eleva-tor, discharging to a short 18-in. conveyor. From the conveyor the tailing is discharged into a dividing hop-per, from which point the plant is arranged in three separate units. Each unit consists of a ball-mill in closed circuit with a classifier, and an 8-cell flotation machine and has an approximate capacity of 300 tons per 24 hours.

Jan 8, 1927

By F. M. Drake

IN this paper I propose to describe a plant which I lately erected for the Mount Stewart Lead and Silver Mining Company of Leadville, New South Wales, Australia. I am indebted to Mr. W. F. Burrow, of the Roads and Bridges Department of New South Wales, for the drawings which I present herewith, he having reduced and assembled them from my working drawings. The works are situated on a sloping hillside, but sufficient fall mas not available to have the furnace as high as desired, and at the same time have a good slag-tip and sufficient depth on the ore-floor to store a supply of ore and flux. The ore is delivered on the ore-floor (which is of the full width of the furnace-building, and extends back into the hill a distance of seventy feet) by two overhead tramways (not shown in the drawings), one on each side. From these the ore-mixture is made up on one side, while it is being taken to the furnace from the other. The fuel also is delivered by these tramways. The fluxes are stored on a floor directly at the back of the boiler and engine room. The boiler is a Cornish one, 6 feet 6 inches in diameter by 25 feet long. Its flue is 3 feet in diameter and does not contain Galloway tubes. The working-pressure is 40 pounds per square inch. The engine is an old-fashioned one, with a cylinder 16 inches in diameter by 30 inches stroke. Both the engine and boiler had been part of the plant of a defunct gold-mining company. They were very extravagant in their consumption of fuel. The blast is supplied by a rotary pressure-blower, of the Baker pattern, made in England. It has a capacity of 60 cubic feet per revolution. The furnace, which has several novel points, is shown in detail in Figs. 1, 2 and 3. The jackets are of cast-iron, and are higher than those generally used. They are different, too, in that the feedwater inlet is through a hand-hole plate near the bottom. This plate is fastened to the jacket by stud-bolts, and is provided with a baffleplate, which prevents the cooling water from impinging against the inner plate. The outlet is by a goose-neck at the top, which dis-

Jan 1, 1893

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

By W. L. Maxson

GRINDING is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grind-ing installations. There have been some tests published, notably those of Lennox,1 which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was .then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the compari-sons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating, load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to he expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method.

Jan 1, 1933

By W. R. Finney

THE formation of scale in boilers and other industrial equipment, and the corrosion of such equipment, are closely related problems. Since in the petroleum industry these problems cover a very broad field, this paper has been confined to the effects of scale and corrosion on gas engines, compressors, pipes and fittings, used in plants extracting gasoline from natural gas, and the steps taken in arriving at a workable plan for combating these evils at the Midwest Refining Co.'s plants in the Salt Creek field, Wyoming. Eliminating, or at least minimizing, the many deleterious effects occasioned by the use of bad water in jackets and cooling systems of gas engines and compressors has been the subject of much study for many years but no generally accepted plan has been evolved. The problem was unusually difficult at Salt Creek, as the severe winters of Wyoming bring operating conditions quite different from those encountered in warmer states, and the water available was especially bad. While the conditioning of water to prevent scale and to lessen corrosion may not be a particularly difficult problem in plants in large industrial centers, it becomes much more difficult when attempted at plants remote from railroads and by men without previous experience to guide them. In fact this difficulty has been so great in the Wyoming oil fields that until comparatively recently it has been the practice to allow much equipment to be ruined rather than to attempt corrective measures. At the Midwest plants this problem was given attention first by the plant men and later by both plant men and laboratory staff. To the latter it was simply one of many problems which arise in connection with field and plant operations, which must be studied and, if possible, solved. Many mistakes were made during the course of this investigation, but since mistakes, properly interpreted, are of value in guiding one's steps aright, it is believed that a review of the different stages of development which have led up to the present method of handling this problem will prove of interest to the industry.

Jan 12, 1926

By H. S. Drinker

I. The Mines THE first discovery of zinc on the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Röpper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded on the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. It is supposed that the zinc was originally disseminated through the

Jan 1, 1873

By Robert H. Chapman

During the past two years the writer has been traveling in the Lewis and Clarke timber reserve, locating the boundaries and reference-monuments for the Geological Survey. The Lewis and Clarke reserve lies in northwestern Montana. The region is very mouutainous, the main range of the Rocky mountains passing through it, dividing the waters of the Columbia and Missouri rivers. The mountains do not rise in one important and well-defined backbone, but in a series of parallel ridges, striking nearly northwest and southeast. Between these ridges, and, in general, parallel to them, are the drainage-systems. Beginning at the west, the rivers are the Swan, emptying into the Flathead lake, the South fork and the Middle fork of Flathead river, both emptying into the main Flathead river, which, in turn, empties into the lake of that name. The continental divide passes through the reserve from the southeast corner to the middle of the northern boundary, and the stream of most importance east of it is the Sun river, which heads well toward the north, and flows southeasterly and then eastward, and, emerging from the mountains, flows across the great plain of' the Missouri river. The southern boundary is drained by the Big Blackfoot river, flowing westward; the northern boundary, by the several branches of the Flathead river. The accompanying map (which is only a sketch, and does not represent the final work of the Geological Survey in this forest-reserve) shows clearly the parallel systems of drainage and ridges. The westernmost mountain range, the Mission, divides the great valley of the Flathead from the Swan river valley. The

Jan 1, 1900

By Axel Sahlin

The day is long past when linen and cotton rags were the exclusive raw material of the paper-trade. Wood-fiber, chemically or mechanically prepared, straw, hemp and Esparto grass have largely supplied the demand, which the old materials did not suffice to fill. But even these newer fibers have been of late supplanted, to some extent, by mineral pulp. Weighting and filling materials have also been resorted to, partly to give body to the fabric, partly to increase its weight and reduce the cost per pound. China clay, sulphate of lime and soapstone have generally been employed as loading materials. Even though these materials lack fiber, their addition must by no means be viewed, as it too generally is, entirely as an adulteration. No doubt, to a certain extent, they weaken the paper ; but for ordinary grades the addition of these non-fibrous substances is a positive advantage, as they close the pores between the fibers and lend to the paper a great degree of opaqueness and a superior finish. Fibrous talc, as a form of pulp, has the same effect, without appreciably weakening the paper. When, therefore, some fifteen years ago, fibrous talc in large quantities, and of marvellous purity and whiteness, was discovered in the neighborhood of the town of Gouverneur, it was not long before the

Jan 1, 1893

Copper from Central Africa was well known to the Arab slave traders who depredated the country in the nineteenth century. By the 1870's slave raiding was so intense that the habits of the tribes were disrupted, and they no longer worked the copper deposits or made the crosses and bars of copper which had been their custom. In fact, the country had been greatly depopulated by the slave raiders. News of this horror was spread to the civilized world by missionaries and, in particular, by David Livingstone's writings. Whether to extend geographic knowledge, to suppress slavery or for national aggrandizement, the rush for African territory was on at the end of the nineteenth century. Cecil Rhodes at this time was established by his successes in diamonds and gold. He obtained the blessing of Lord Salisbury in 1889 to form the British South Africa Company under crown charter. His objectives were to occupy the lands north of the Zambezi for England and pay for development out of the country's mineral deposits. He planned to occupy the territory and close the gap to form an all-British route from the Cape to Cairo, one of his great dreams. With this master plan in mind he sent his agents into the field to make treaties with the tribes.

Jan 12, 1962

By Leon Y. Sadler, E. K. Landis

Froth flotation has been described by several authors" as being analogous to a first-order rate process. Although a few investigators"," have found orders other than one fit their data best, the rate is described most often by the first-order equation, [ ] where r is rate of disappearance of floatable mineral by flotation, C(t) is concentration of floatable mineral in the cell, t is time, and k is first-order flotation rate constant. One of the difficulties in using this rate equation to develop a mathematical description of an actual flotation process is the determination of a suitable value of the constant k. The value of k, which reflects the floatability of the floatable mineral, is dependent on the hydrodynamic conditions in the cell, type and concentration of flotation reagents used, pulp density, and pH, method of froth removal, aeration rate, particle characteristics, and many other factors. Therefore, it is reasonable to expect that each particle of floatable material has a distinct value of k and that a unique distribution of k values exists for given feed and cell conditions. This has been observed and discussed by several investigators, and mathematical descriptions of the batch cell and steady-state continuous cell with distributed flotation rate constant have been developed." The mathematical description in the form of a transfer function of the continuous or flow cell under unsteady-state conditions with a distributed flotation rate constant has not been presented in the literature. The purpose of this note is to make such a presentation. The basic features of the perfectly mixed continuous

Jan 1, 1974

HAVING told you of the practices of the arts involving other metals, I wish to tell you also of the practice of that of tin.* Indeed, since this is an easily melted metal, in common use for the utensils which are made for human needs, it is an art known not only to skilled men but also almost to children, wherefore I could proceed with- out telling of it. However, besides the production of plates and bowls and many other dishes for eating from and keeping things in, this embraces two other arts, both of which you should know about because they are useful and beautifid. One of these is the art .of making the letters with which books are printed, and the other is that of making the sheets from which organ pipes are built. The vessels, as perhaps you have seen, are cast one by one in moulds made of white tuff. Several pieces fastened together are then put on the iron axle of a wheel rotated by hand, and [138v] they are turned with a slightly bent tool which has a cutting edge. In this way they are made thin and of a good shape. Then they are polished with a piece of linen cloth and a little powdered tripoli, and thus they are finished. The letters for printing books are made of a composition of three parts of fine tin, an eighth part of black lead, and another eighth part of fused marcasite of antimony.t The desired quantities of these metals are melted

Jan 1, 1942

By Hugh M. Roberts

The important place in the economic life of the country that is occupied by the United States Geological Survey and the various state surveys is appreciatcd by most members of our Institute. To the public at large, the functions of these surveys are no doubt largely unknown, and taken for granted. Possibly a realization of the value of the work of these government branches is brought home most fully to that group of our members whose duties as examining engineers and mining geologists take them to mines and prospects in many different parts. The examining engineer or geologist is usually seeking for a judgment on the value of an enterprise from the standpoint of the useful minerals that may or may not be present; he must also attempt some prediction as to future market prices. On his opinion rests the determination of the expenditure of money, which rendered into other language means the expenditure of human effort. An opinion on an exploring venture or the reasoning out of the probable extensions of an orebody requires among many other things a background of knowledge covering the geologic horizons not only of an immediate area but of the surrounding area, a knowledge of the structural geology and of the causes that have operated to form the ores as they are. The great storehouses of this knowledge are the statistics, reports and maps issued by the various geological surveys. They supply the groundwork for additional observations. To these, reference is always made when going into a new district. The technique of work in the field and laboratory, and to some extent the hypotheses that underlie our methods of approach, have been formed by men such as Van Hise, Leith, Kemp, Spurr, Emmons and Lindgren, who developed their powers in the service of the geological surveys. In addition to whatever originality of thought, or power to observe facts and analyze them, may be our portion, we require, in the application of the arts and sciences, a knowledge of what has already been done. We stand on the shoulders of those who have gone before, and the extent of our vision often depends upon the thoroughness with which we form earlier work into one whole and make use of it.

Jan 1, 1935

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940