Search Documents

By C. R. Boyd

The region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron,........58.15 Water,.........12 96 Alumina,........2.32 Silica,.........1.09 Phosphorus,.. none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows :

Jan 1, 1880

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By C. R. Boyd

THE region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron, - 58.15 Water, - 12 96 Alumina, - 2.32 Silica, - 1.09 Phosphorus, - none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows

Jan 1, 1880

By R. G. O’Meara, S. M. Runke

THE Bureau of Mines has been charged by Congress to investigate processes for the production of alumina from low-grade bauxite, alunite, and clay. As one part of the program, an investigation of the application of ore-dressing methods to improve the grade of high-silica bauxite is in progress at the Mississippi Valley Experiment Station at Rolla, Mo. This paper summarizes data obtained so far and presents detailed results of tests on four typical samples. MINERALOGY OF BAUXITE The name bauxite originally was used to designate the dihydrous aluminum oxide (A1203.2H20). The designation has been retained, although the existence of a specific mineral of such composition has been disproved. The term is now applied to ores of aluminum consisting of various mixtures of the minerals gibbsite (A1203.3H20), diaspore (A1203.H20), and boehmite (A1203.H20). The predominant hydrous aluminum oxide in most American bauxite, however, is gibbsite. In some instances bauxite may be amorphous mixtures of the hydrous aluminum oxides that approximate the composition of dihydrous aluminum oxide (A1203.2H20). The proposed name for this material is cliachite. Gibbsite and boehmite, the trihydrate and monohydrate, are soluble in a solution of sodium hydroxide at elevated temperature and pressure, whereas diaspore is practically insoluble. The solubility of these two minerals is the basis of the Bayer process of alumina extraction. All bauxites contain certain impurities, the commonest of which, in the order of their importance, are: silica, principally as a constituent of kaolinite, and to a lesser extent as quartz; iron, as hematite, limonite, and siderite; and titanium, as ilmenite, rutile and leucoxene. Minor impurities are zircon, cobalt and nickel. Bauxite is produced commercially in Arkansas, Alabama, Mississippi, Georgia and Tennessee, but the most important deposits in the United States are in Arkansas, in the vicinity of Little Rock. HISTORY OF BAUXITE BENEFICIATION The literature on bauxite beneficiation is limited, but the reports of Gandrud and DeVaney1 and Clemmer, Clemmons, and Stacy2 show the possibilities of flotation as a means of beneficiating bauxite. Their work has also developed reagent

Jan 1, 1944

By R. A. Liddle

Intermitt'en'I'ly during the past 10 years showings of oil and gas in tests drilled in the eastern part of Texas have stimulated the search for production. Tests on the flanks of the long-known salt domes, principally Keechi and Butler, have found oil in small quantity in the Woodbine formation of the basal part of the Upper Cretacrous. In the central part of Cherokee County, Colliton et all in 1926, in their Clapp No. 2 found a good showing of 37" B6. oil at about 3500 ft. Several wells were drilled in 1926 and 1927 as a result of this showing. On Jan. 22, 1927, Humble Oil & Refining Co. wildcatting on Carey Lake salt dome, obtained commercial production in its Clark No. 1. This inaugurated intensive exploration both for salt domes and for other types of structure. As a result several new domes and a few promising structures of other types have been discovered. Development in East Texas durinG 1927 Carey Lake Dome Location.—On the Neches River in Anderson and Cherokree counties, 10 miles west of Jacksonville, Cherokec (lounty. (Fig. 1.) date of Discovery.—During 1925 geologisls of the Humble Oil & Refining Co. working in the Neches River valley discovered slight surface fracturexs, cratic dips, and slickensided clays and sands in green-sands of the Mount Selman formation north of Carey Lake. A number of core tests were drilled by the Humble Oil & Refining C'o. during 1925 and 1926, some more than 1500 ft. deep, to check their surface obsuvations of faulting, and the possibilities of a salt dome. On May 16, 1927, solid rock salt was reached at 2142ft. in the first deep test on the prospect. Surfacc Indications.—Surface indications of the Carey Lake dome, though not as evident as manifestations at the previously known domes of Palestine, Keechi, Butler, Grand Saline, Steen and Brooks, are more noticeable than on any of the domes discovered in 1927. F. E. Poulsen, of the Pure Oil Co., who examined the area before the deep tests were drilled, noted the alignment of erratic surface dips which suggested faulting, especially in conjunction with slickensiding, and the local deflec-

Jan 1, 1928

By George L. Lyle

WITH the advent of World War II, the need for agricultural products rose phenomenally and caused a similar increase in demand for plant foods of which phosphate rock is one of the more important raw materials. By the close of the war or shortly thereafter, all of the operating companies were expanding their production facilities. Many companies installed modern bulk material handling facilities. Designs varied, but were generally of the overhead trestle type of storing conveyors. American Cyanamid studied these various installations but was not satisfied with the conventional system because of high initial cost, increased maintenance problems in the way of painting structural steel that might be submerged in stored materials, and because of slightly increased operating costs. As a consequence of these economic analyses, conferences were held with the various conveyor manufacturers to develop a better method of storing and reclaiming. After considerable engineering study, one conveyor manufacturer suggested the unique system which was installed in 1950.

Jan 8, 1954

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬lows: the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circum¬stances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money- prize to the younger men, rather than the medal.

Jan 1, 1923

By H. Nakazawa, I. Iwasaki

Galvanic contact, occurring between electrically conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions. The results were correlated with their oxygen-consuming characteris- tics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased, whereas that on pyrite increased when these minerals were held in contact. An electro- chemical mechanism was proposed for the observed behaviors.

Jan 1, 1986

By Richard F. Link, George S. Koch

About 50,000 assays of mine samples were required in a preliminary investigation of the distribution of gold, silver, lead, copper, and zinc in two large Mexican mines, the Frisco mine at San Francisco del Oro (Chihuahua) and the Fresnillo mine at Fresnillo (Zacatecas). The feasibility of working with so many assays rests directly on the use of machine processing methods. The purpose of this article is to describe the methods used because machine (or data) processing can also be used efficiently to make the many calculations from mine assays needed in mining operations. No particular originality is claimed for these methods, which are straightforward applications of standard procedures for machine processing. Inasmuch as machine processing is essentially a routine job once it is begun, procedures must be organized more completely than is the case where human judgment can be inserted at every step. Before undertaking any work, it is necessary to decide carefully just which data must be processed as well as the exact results desired.

Jan 9, 1960

By Frank Somogyi, Donald H. Gray

Techniques for in-situ dewatering of tailings and slimes include evaporation, decantation, drainage under self weight, drainage by surcharging, and electro-osmosis. A promising technique for increasing drainage efficiency is a vertical, wall-drain system, which can be constructed in an impoundment concurrently with deposition of slurried tailings. The vertical drains, which can be constructed from sand or from the coarse fraction of a tailings stream, greatly speed the rate of consolidation of the fine tailings or slimes. The performance of a wall drain system and the semitidy of consolidation efficiency to certain variables or system parameters are examined. These parameters include the slime deposition rate, ratio of drain to slime permeability, drain width, and drain spacing.

Jan 1, 1979

By D. M. Hausen

This study identifies and describes various crystalline phases of the V205-Na20 system, and relates their properties to metallurgical aspects of vanadium production. Phase equilibria and stability ranges of sodium vanadate phases of varying molar ratios of Na20/V205 were investigated in a variety of plant products, ranging from fused "black cakes" (V20 melts) to "salt roast" calcines. Crystalline compounds, Including vanadium pentoxide, V205; sodium vanadyl vanadate, 6 phase, Na2O.V2O5.5V2O5; sodium vanadyl vanadate, y phase, 5Na20.V204.12V205; sodium metavanadate, Na20 .V 05; sodium pyrovanadate , 2Na20 .V205; and sodium orthovanadate, 4Na20.~2~5, have been characterized with the aid of X-ray diffraction patterns, infrared spectra, and optical properties in addition to chemical analyses, as a guide to mineralogical "troubleshooting" of plant problems and processes in vanadium pyro- and hydrometallurgy.

Jan 1, 1984

By C. V. Millikan

New developments in air-gas lift practices in the Mid-Continent area since our Pall meeting in Fort Worth have done much to increase the efficiency of installations, and thus bring within economic limit of air-gas lift many wells which could not have been flowed profitably before. After the gas-lift had so thoroughly demonstrated its value in the Seminole field, its use spread to other areas and many installations were made of which the economy could be questioned. In the Seminole area, when production began to decline it was necessary either to increase the efficiency of the air or gas-lift or to put the wells on the pump, and pumping was not a process of lifting oil to which any operator looked forward with confidence. These conditions have resulted in the development of many practices which increase the efficiency and permit wells to be flowed with air or gas which earlier could not have been flowed economically, and wells which have been flowing to continue to a lower rate of production. The practices which have come into more common usage in the Mid-Continent area recently are mostly revivals of and improvements on practices which have been known in air-lift work for several years. Many arc peculiar to the individual well on which they are used. Intermittent Flowing Some interesting results are being obtained in Seminole and other districts by intermittent injection of gas. Gas is introduced during per-iods iods of 3 to 5 min. at a rate considerably over that necessary to acquire the production at a steady rate of injection, and is then cut off for a period of 3 to 15 min. Two to five wells are run from the same group of conlpressors. The total volume of gas required is sometimes reduced as much as one-third of that required when it is introduced at a constant rate, without changing the amount of oil production. The maximum pressure required is usually higher, but the average equal to or lower than that required for constant rate of flow. The effect on the wells is usually an irregular rate of flowing which may cause inconvenience where recycling is practiced. It would seem that this increase in efficiency is due to less slippage when the gas is introduced intermittently than when it is intro-

Jan 1, 1928

By B. L. Thane

Within the past few years, the mining industry has taken a new impetus in all its branches. New mines are being opened every day, while old ones, which have been either working at a loss, or have been compelled to shut down, are now gradually being reopened and placed on a paying basis. This growth and new life is due, in a measure, to the discovery of new mining districts, but the most important cause of the progress is the wonderful advance that has been made in all branches of mine-engineering. By means of the important inventions and discoveries that have been made in mechanics, chemistry, and electricity, we are now able to work ores which, only a short time ago, would have been regarded as worthless. We find, for instance, the electrician eliminating two of our greatest difficulties, those of distance and superior elevation, while the mechanic has brought to the highest degree of perfection, not only ore-crushing and hoisting machinery, but all such devices as pertain to the mechanical handling of ores, and, at the same time, the metallurgist, with his combined chemical and mechanical skill, has helped us to extract the precious metals from the most refractory of ores. But when we turn to examine methods in actual use for

Jan 1, 1900

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Mon- day of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years' employment in positions of responsibility may be waived by the Committee on Membership in the case of persons who have done notable original work in mining, or metallurgy, or have won distinction by research or investigations In one or more of these subjects.

Jan 1, 1928

By P. Raffinot, M. Rey, V. Formanek, G. Sitia

Six years of laboratory study, followed by three years of mill operation treating more than 10,000 tons of ore, have established the flotation of oxidized zinc ores with fatty amines as an efficient process. Recently the method has been applied with success to partially oxidized sulphide ores. In this paper the authors give an account of their research and the milling results obtained in Sardinia since 1951. CONCENTRATION of oxidized copper and lead ores by flotation has been practiced for 30 years, but flotation of oxidized zinc ores has remained unsolved until a few years ago. This problem is, however, of great importance in mining districts where large tonnages of oxidized zinc ores exist in underground mines or in dumps. Some sulphide ores also possess a degree of oxidation high enough to justify recovery of oxide zinc minerals. Various attempts have been made to float the zinc carbonate, smithsonite. It is well known' that smithsonite can be collected with fatty acids, but as the predominant gangue constituents, limestone and dolomite. are floatable with the same reagents, fatty acids are difficult to use. Gaudin has shown,' on mixture of pure minerals, that smithsonite can be floated with higher xanthates, or better, with higher mercaptans. Another procedure, briefly mentioned by Davis," consists in sulphidizing the ore, activating the zinc carbonate with copper sulphate, and floating with ordinary xanthates. This process was attempted in the writers' laboratory in 1946, but results were erratic. It has since been taken up by Italian engineers and is in operation on certain types of ores. Two other research projects should be mentioned. In 1942 Erlenmeyer and others' floated synthetic mixtures of smithsonite and gangue minerals with hydroxyquinoline, an analytical reagent for zinc. On the other hand, Bunge, Fine, and Legsdin published in 19465 Some interesting results obtained on Missouri oxidized zinc ores. With sodium oleate as a collector and a combination of sodium hydroxide, sodium silicate, and citric acid as a limestone depressor, they secured, after four cleaning operations, a good grade of concentrate. With many ores this reagent combination lacks adequate selectivity. In 1939 M. Rey initiated a program of research on this important problem. Work was pursued first at the School of Mines in Liége, Belgium"' and later in Paris in the laboratories of Société Miniére et Mbtallurgique de Penarroya and Société Minerais et Métaux. Reagents used in the beginning were higher xanthates and mercaptans, later fatty amines. Sulphidization with sodium sulphide was found necessary. These conditions make possible the flotation of zinc carbonate and zinc silicate. Two milling plants were put in operation in Sardinia in 1950 and several others are now contemplated." ' It should be mentioned that unknown to the present writers McKenna, Lessels, and Peterson were

Jan 1, 1955

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By Peter R. Morris, Alan J. Heckler

THREE angles are required to specify the orientation of a crystallite with respect to a physical reference frame. The distribution of crystallite orientations in a polycrystal is thus a function of three angular variables. The most widely used experimental techniques for studying orientation in polycrystals lead directly to the pole figure representation, i.e., the distribution of the poles of certain crystallographic planes in terms of two angular variables. In recent years1-5 methods have been developed which permit determination of the (three-angle) crystallite orientation distribution from several (two-angle) pole figure distributions. In this work Roe's method has been applied to the study of orientation in hcp materials. The method is illustrated for commercial purity titanium sheet (Ti-70) which was cold rolled (65 pct reduction), annealed at 1450°F for 3 min, and air cooled. The grain shape was observed to be equiaxed after this treatment. EFFECTS OF PHYSICAL, CRYSTALLOGRAPHIC SYMMETRY In Roe's method the crystallite orientation distribution, w(?,?,F), is expanded in a series of generalized spherical harmonics 11(?,?,F) = E E E W^Zirmtye-tote-in* [l] 1=o ,,,=-I ,,=-I where { = cos 8. The set of Euler angles employed here is illustrated in Fig. 1. The axis for each rotation is denoted by a double arrowhead. The positive sense of each rotation is that of a right-handed screw advancing in the direction of the double arrowhead. The X, Y, and Z directions correspond to the rolling direction, cross direction, and normal direction, respectively. In the initial orientation (10.O), (12.O), and (00 . 1) planes are perpendicular to the X, Y, and Z directions, respectively. The IC/ rotation about the Z axis is carried out first by rotating X into X', Y into Y', and leaving 2 unchanged, i.e., Z' = Z. The 8 rotation about the Y' axis is carried out second by rotating X' into X", 2' into Z", and leaving Y' unchanged, i.e., Y" = Y'. The I$ rotation about the Z" axis is carried out last by rotating X" into X"', Y into Y"', and leaving 2" unchanged, i.e., 2"' = 2". Any specified orientation of the X'", Y'", and Z'" crystal-fixed axis system relative to the X. Y, and Z physical axes (rolling direction, transverse direction, and sheet normal direction, respectively) can be obtained by appropriate IC/, 8, and (F rotations. The Zl,, of Eq. [l] are the Jacobi polynomials, augmented by the square root of the weight function. The Zl,, are symmetric in m,n, i.e., Zl,,= Zlnm. For orthotropic physical symmetry and hexagonal crystallographic symmetry, the coefficients, W!,,, of the series are all real, W!mn = Wzfi, = Wlm~ = Wlfi~, 1 and m are even and n is restricted to 6k, where k = ...,-2,-1, 0, 1, 2, .-.. The determination of the Wlmn from pole figure data has been previously described.'~~ The Zl,, may be written in multiple angle form

Jan 1, 1970

[RECEIPTS Magazine, Advertising $ 32,823.60 Sale of Magazines 3,933.29 Total Magazine $ 36,756.89 Dues, Arrears 5,866.97 Dues Current 100,223.80 Dues of New Members 6,143.29 Dues in advance 1,586.32 Initiation fees 6,820.00 Sale of Transactions 5,464.99 Sale of Binding 5,618.90 Sale of Pyrometry Volume 336.30 Sale of Indexes and Emmons 106.10 Sale of Pamphlets 575.32 Miscellaneous Receipts 105.60 Interest on Bank Balances 1,217.67 Interest on Life Membership Investment 512.18 Interest on James Douglas Library Fund 5,678.67 Total Receipts $177,013.00] [ ]

Jan 1, 1925

By G. A. Alers, F. Borik

Rolled sheet products are elastically anisotropic and a large number of measurements of Young's modulus and rigidity modulus are necessary to completely specify their elastic properties. This paper describes and uses a simple measurement technique to obtain the nine elements of the elastic modulus tensor from which all the elastic The elastic properties of a polycrystalline material are usually specified by giving the Young's modulus E and the rigidity modulus G. Unfortunately, these two moduli by themselves are insufficient to completely specify the elastic properties because the rolling process introduces a preferred orientation which makes the material properties can be deduced. In particular, the variation of Young's modulus and the rigidity modulus in the principal planes of a sheet of ausformed steel were deduced. Furthermore, the variation of Young's modulus in the rolling plane was compared with direct measurements. anisotropic. This anisotropy makes E and G functions of the orientation of the test specimen in the sheet so that a complete description of the elasticity requires many measurements on a large number of specimens. A more fundamental approach to the problem is to consider the sheet as a single crystal and measure the elements of its elastic modulus tensor. Although this appears formidable, there have been developed recently high-frequency ultrasonic techniques which yield these tensor elements directly. The symmetry of a rolled sheet is such that it behaves elastically as if it were an orthorhombic

Jan 1, 1965

By James B. Vance, Parviz Mottahed

An extensive research program has been carried out at PCS Mining for some time into the use of high frequency microseismic emissions in the range of 30-200 kHz for roof fall warning in the mines. A laboratory investigation on loaded samples of potash has established a close correlation between acoustic emissions and the applied load. The tests also indicated the occurrence of the Kaiser effect. The positive and encouraging response from underground testing and controlled laboratory testing has lead to the extension of the investigation into correlation of the high frequency microseismic emissions and the change in stress distribution due to mining. Hydraulic borehole pressure cells were installed at different depths ahead of the advancing boring machine. The output due to the stress change and the microseismic event count was monitored by a continuous chart recorder. This paper discusses the results of this instrumentation. The results confirm the strong correlation between the two measured parameters and outlines future areas of research for the use of the high frequency microseismic emission techniques in quantifying the changes in stress distribution.

Jan 1, 1984