Search Documents

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling,' forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has. been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses, and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

By Andrew Hodge

ISSUES IN MINING LABOR The examination of mining labor issues is often confined to health, and safety. There are other issues, including the present state of mining manpower availability and utilization, and the nature of mineral industries' industrial relations, which are worthy of consideration. The state of the labor market for mining skills, the availability and utilization of mining engineers and related disciplines, the state of research and its employment of scientists and engineers, and the condition of mining industrial relations with all these groups, all have an important effect on the viability and economic health of the minerals production sector. PRODUCTION LABOR Why examine an industry's production labor market? People involved in an industry should be aware of what labor supplies will be relative to industry requirements. This advance information allows industry and government to plan ahead to alleviate problems by moving to affect labor supplies or to accommodate production to expected labor supplies. This is less costly and less painful than responding after the fact to labor market changes. Any industry requires some form of labor. Labor is especially important to the mining industry. Mining labor is well paid. Average annual earnings are higher than in manufacturing. Average hourly wages are also higher. Payroll costs form a high percentage of total cost in coal mining and nonmetallic minerals mining. In metal mining the percentage is comparable to the average for manufacturing. Payroll cost in oil and gas extraction is quite low, but a major proportion of cost is in the form of income to proprietors, i.e., unincorporated businesses. Mining labor is worthy of specific attention. The minerals extraction labor is unique in many ways. Mining labor and especially underground miners are differentiated from other "unskilled" labor. Miners cannot be considered as part of a larger labor pool. The mining labor market has exhibited a unique combination of characteristics. Mining is the only large sector of United States employment in which hourly wages are high and continuing to rise, yet employment declines. Although industry has introduced new labor-saving investments, and labor requirements continue to decline, there is evidence of a mining labor shortage. Specific problems have arisen in the mining labor market such as a present labor shortage in nonfuels mining. Understanding the causes and remedies for these specific problems is also important. These various problems and questions may be handled in a unified manner by examining the relationships of certain economic variables. The relationship that exists between changes in output, employment, labor productivity, and hours worked per week may be stated explicitly:

Jan 1, 1976

By S. C. Langdon, Henry S. Rawdon

The following note describing the behavior of copper under rather unusual conditions is offered for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning, as well as softening it. It is well known that metals may be rendered very brittle by electrolytic action in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear 2 similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. TO demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 801" C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for several minutes. When removed from the bath, cooled, and tested for brittleness by bending the specimen back and forth, while clamped firmly at one end in a vise, the copper rod was found to be very brittle, as compared with a rod of the same length of the untreated copper tested

Jan 1, 1921

By Alexander Squire

ONE of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test: methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials' and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three-chemical analysis, density, and hardness. The last of these may or may' not be a pertinent characteristic, since the indentation hardness of many powdered-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple, to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. , It. is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the properties of compacts formed from different types of powders are made on the basis of compacting... pressures instead of density, and for. this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes. on, like some writers, talking about ' the former ' and 'the latter ', 'he ', 'she ', 'it), and 'they’, through clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a feeble ending for a serious statement. How often do you hear 'the former' and 'the latter' in conversation? Good conversation is a guide not to be disdained. When you must use 'the latter ', do not confuse it with 'the last '. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is beat. "Partly prevented" is a poor phrase. 'Prevented' is a word that does not lend itself readily to modification. He means ' checked ' or 'corrected '. These steps are necessary to produce the gas, crude oil, and ammonia, the latter [last] of which is in solution in the water obtained along with the oil.

Jan 1, 1931

By A. M. Rowe

A considerable quantity of experimental hydrocarbon K-factor data has been correlated as a function of component identity, temperature, pressure and convergence pressure. To utilize these correlations effectively, convergence pressure must be determined accurately, particularly for volatile mixtures near their critical states. This paper presents phase diagrams that illustrate physically the meaning of convergence pressure. A new method, referred to hereafter as the "critical composition method", will be outlined for calculating convergence pressure. An example calculation has been included to illustrate how to use this new technique. INTRODUCTION The principle of hydrocarbon phase composition calculations as applied to such diverse problems as optimizing separator performance or predicting fluid compositions at various stages of reservoir depletion is the same. Usually, temperature, pressure and the numbers of moles of the various components of the fluid contained in a given volume are known. Questions answered by the phase calculation are what fraction of the total mass of fluid exists in each of the equilibrium phases, and what are the mole fractions of the various components in the two phases? To answer these questions the Natural Gasoline Supplymen's Assoc. (NGSMA) has correlated a considerable quantity of K-factor data as a function of temperature, pressure, component identity and convergence pressure.l To use these correlations to obtain the best answers possible, one must be able to calculate the convergence pressure. This is particularly true for over-all fluid compositions in the neighborhood of the critical state. STATEMENT OF THEORY Use of convergence pressure as a correlating parameter is based on a postulate similar to the law of corresponding states used in correlating PVT data of hydrocarbon gases. This postulate, which proposes convergence pressure as a correlating parameter, has been stated as follows: "The equilibrium vaporization constant for one component in a complex system is the same as the equilibrium constant at the same temperature and pressure for the same number or kind of components, providing only that the convergence pressures of the two systems are exactly the same at the same temperature and that the components are of the same homologous series".2 This law, as with all laws of physics, cannot be proven theoretically. It can only be justified by experimental data supporting its premises. Arguments have been made that this law violates Gibb's phase rule. For example, consider a four-component system. By Gibb's phase rule, which is thermodynamically rigorous, f = c — P + 2 =4, for a four-component, two-phase system. Thus, four independent intensive variables must be specified to establish completely all the intensive variables of the equilibrium phases. On the other hand, according to convergence pressure theory, only three variables need be specified for any mixture containing four different components. These variables are temperature, pressure and convergence pressure. Thus, the two laws appear to be in conflict. However, the convergence pressure postulate is more restrictive than Gibb's phase rule. It applies only to mixtures of the same homologous series. Hence, these two concepts are not in disagreement. PHASE DIAGRAMS DESCRIBING CONVERGENCE PRESSURE This paper presents phase diagrams grading from the simple two-component system to the more complex four-component system to illustrate convergence pressure. A less abstract definition of convergence pressure will be stated that is

By J. G. Savins

Analytical procedures are described for optimizing the selection of a rheological model when it is desired to express the functional relationship between true shearrate and shearing stress in analytical form. The procedures are extended to two principal model categories — "Generalized Newtonian" and "Viscoplastic" models. Graphical examples are presented to illustrate the utility of certain characteristic deriuative functions in distinguishing between these categories and in determining how well a particular model reflects the flow behavior of rheologically anomalous materials in simple shearing flows. INTRODUCTION Modern drilling fluids and fracturing fluids, being chemically complex, are frequently non-Newtonian — a peculiarity which complicates the solution of problems such as designing flowline and process equipment, and predicting laminar-turbulent behavior, solid-suspending ability and cutting-transport efficiency. Therefore, techniques of data analysis which accurately characterize the behavior of rheologically complex materials are needed for the accurate formulation of solutions of these and similar problems. It is the purpose of this paper to describe the application of a sensitive method of rheological data analysis — the dual differentiation-integration method of optimizing the selection of the functional relation between shear rate and shearing stress — to a variety of materials of interest in drilling and production practices. BASIC CONCEPTS THE DIFFERENTIATION METHOD To a first approximation, the viscosity function for a non-Newtonian system can be expressed in a form analogous to Newton's law of viscosity by the following generalization2.3 between the stress On introducing the restrictions that the system is incompressible and the motion is rectilinear, then l = 0 and l3 = 0 ; and with the further restriction that the flow is slip-free, the viscosity (an invariant) is then determined solely by 12. With this approach one can set up a suite of integral equations relating observed kinematical and dynamical parameters for certain types of flow experiments involving simple shearing motion, e.g., flow in a cylindrical tube, flow between rotating concentric cylinders, and flow between fixed parallel surfaces of large aspect ratio. Taken in the order cited, these integral equations are as follows.

By J. R. Low, M. B. Reynolds, L. O. Sullivan

The effect of neutron bombardment upon the stability of type 347 austenitic stainless steel has been investigated by a magnetic technique. The relation of the ferrite content of a stainless steel to its magnetic properties is given, and an apparatus suitable for the measurement of the ferromagnetic saturation induction of small specimens is described. Results of measurements on irradiated specimens are tabulated. Exposure to a neutron flux was found to cause a slight increase in the ferrite content of type 347 stainless steel, the change increasing with increasing length of exposure and with increasing initial ferrite content. The similarity of the effect of irradiation to the effect of annealing is pointed out. Possible effect of irradiation upon density of austenitic stainless steel is discussed. COMMERCIAL austenitic stainless steels are alloys of iron, chromium, and nickel, plus small quantities of other elements. Although these alloys are normally used in the austenitic condition, this state is thermodynamically metastable at ordinary temperatures and transformation to a more stable state takes place under favorable conditions. In the austenitic state, these stainless steels have the face-centered-cubic crystal structure characteristic of y iron, but the stable state at room temperature is a mixture of austenite and body-centered-cubic ferrite. The transformation from the pure austenitic condition may be brought about by cold working the alloy at a temperature below that at which the aus- tenite becomes thermodynamically unstable (about 400°C), the completeness of transformation increasing with increasing severity of cold work and decreasing temperature. The behavior of the austenitic stainless steels under ordinary conditions of use is rather well known. However, use of these alloys in a nuclear reactor introduces a new variable: the effect of neutron bombardment upon the transformation from the austenitic to the ferritic state. It was with this in mind that a study of the radiation stability of austenitic type 347 stainless steel was undertaken. Magnetic Technique for Ferrite Determination Commercial austenitic stainless steels such as type 347 undergo little transformation under normal conditions of fabrication and use. In view of this fact, it seemed likely that neutron irradiation would change the ferrite content of the alloy but little. The method chosen for measurement of the effect of neutron irradiation was thus limited to one which would be quite sensitive to small changes in the ferrite content of the alloy. Of the properties of the stainless steel which can be measured, the magnetic characteristics are most sensitive to the quantity of ferrite present.

Jan 1, 1956

By Luther B. Eames

The recovery of dissolved gold from slime pulp in the cyanide process was first accomplished by intermittent decantation. This simple process consists in mixing with the pulp containing the values in solution, a solution of lower gold content, settling the mixture in a tank and decanting the clear supernatant fluid. The thick pulp remaining in the tank is pumped to a second tank together with more barren-solution and again settled and decanted. After several repetitions of this operation, values are so far reduced that further washing is not profitable. The gold recovery of this process is high, but the plant required is bulky, labor cost is high and the amount of solution to be precipitated is excessive. Historical Data As early as 1901, a plant was built in the Black Hills of South Dakota by John Randall, employing the same principles but attempting to make the process continuous by substituting for flat-bottomed tanks, cones which operated continuously, receiving a constant feed and discharging a steady stream of thickened pulp. These cones were operated in series, the thick underflow of the first one forming, with a stream of diluting solution, the feed to the second cone of the series. Barren solution was added to the tank immediately preceding the discharge tank and, after being slightly enriched by the low-grade pulp in this tank, overflowed to form a diluting solution again for the richer feed entering the third tank from the end of the series, and so on back to the richest tank of the series. Clear water was used for the wash in the final tank. This is the principle on which all successful countercurrent decantation plants operate at the present time, but Randall's plant was not successful because of mechanical difficulties in getting a continuous thick discharge from his cone tanks. A similar plant was built in South Africa although there the washes were not repeatedly used, as in Randall's case, but were precipitated after each contact with the ore. This also was abandoned

Jan 1, 1918

By Ray W. Arms

The combination wet and dry coal-cleaning process is not an attempt at a compromise between the wets and the drys nor is its merit confined entirely to the limitation of moisture in the smaller sizes. It is more correctly, and more broadly, an application of the sized-coal cleaning principle adapting itself in an ideal fashion to present day multiple-size preparation practice. The purpose of this paper, therefore, is to call attention to the broader significance of the term "combination wet and dry process" and to mention some of the factors that govern its application. In the narrow sense, when considered apart from the sized-coal cleaning principle, the combination process finds its justification chiefly in the ability to limit the moisture in cleaned coal. Larger sizes of coal offer less superficial area compared with their bulk for the attraction of moisture films. They drain more readily in bins or railroad cars, having more interstitial space for the free flow of water. Therefore, they neither attract nor hold objectionable moisture percentages. In fact, there is so keen a demand for certain washed sizes containing some moisture that hygroscopic salts such as calcium chloride are applied to attract and retain it. When coal deliveries are made on a guaranteed moisture percentage the coarser sizes may be washed and mixed back with the fines without adding greatly to the original moisture but the fines must be dry cleaned or dried to control moisture. Thus in all respects moisture in the coarser sizes is less objectionable than in the fines. The implication of this statement, that moisture is always more or less objectionable, is true. It is safe to say that if dry-cleaning apparatus could be perfected to a point at which its technical results, cost and other aspects would be equal to wet washing, water would no longer be used. As it is, we find that good technical results are more difficult to obtain by dry cleaning than by water. Obviously the use of air tables for coarse coal is not ideal, for it involves the attempt to stratify material in a thin bed on a table surface when the load is only one particle deep. Furthermore, the various air cleaning tables on large sizes require a large volume of air for separation, more power to operate, more dust-collecting apparatus and involve more coal breakage.

Jan 1, 1931

By H. Udin

G. KUCZYNSKI* and B. H. ALEXANDER*—This paper represents a most noteworthy attempt to evaluate experimentally the surface tension of a solid metal. Because of the great importance of such measurements, any proposed method should receive the closest scrutiny before the results can be considered reliable. In regard to the experimental method, we think that the marking of the gauge length by means of tieing knots in the wire may be the cause of some of the spread in the results. Such a knot may be expected to tighten slightly, and thus increase the gauge length, when placed under stress at high temperature. Although this effect would be very small, amounting at most to only a few times the wire diameter. A fairly tight knot in a wire will decrease the wire length by about ten times the wire diameter, thus only a slight tightening of the knot would cause considerable spread in the results. Upon plotting the stress strain curves from the authors' data, the writers found that there was a fairly consistent tendency towards an S-shaped curve, instead of a straight line. Such an effect could be caused by the tightening of the knots. The writers think, however, that the experimental results are fairly reliable, but that there may be other methods of interpreting them depending upon what mechanism is assumed to be responsible for the shrinkage of the wires. The authors have assumed that the stress due to surface tension results in viscous flow. It should be made clear that it has never been demonstrated that viscous flow can occur in metal crystals even at very high temperatures. The experiments of Chalmers13 on tin, which are so frequently quoted as giving evidence of viscous flow at low stresses are by no means satisfactory. In his experiments, Chalmers found that only the initial rate of flow was approximately proportional to stress. He also found that the rate of flow varied markedly with time which, in his experiments, was less than 2 hr. Inasmuch as there is no proof of viscous flow in metals, and the authors have brought forth no conclusive evidence on this point, it may be worth while to investigate other possible mechanisms of material transport which would account for the shrinkage of the wires. The writers wish to point out that in these experiments the shrinkage of the wires can be adequately explained, according to a self diffusion mechanism. Thus, if we assume a concentration gradient for self diffusion which is a function of the radius of curvature of the wires, and assume that diffusion will occur so that the total surface area is decreased, we find the following expression for the self diffusion coefficient: where k = Boltzmann constant r0 = initial radius of the wire T = absolute temperature ? = surface energy 8 = interatomic spacing t = time e = strain at zero applied stress Eq 19 may be used to evaluate the self diffusion coefficient of copper, using the strain measurements obtained by the authors for zero stress as obtained by extrapolating their curves for 5 rail wires. By inserting a reasonable value for the surface energy (1500 ergs per cm2) we find: -66,000 D = 5 X 10e RT [20] The activation energy is of the correct order of magnitude, but the frequency coefficient is much too high, indicating that surface diffusion may be playing an important role. This discrepancy in the action constant is much smaller than the corresponding discrepancy obtained by the authors for the viscosity coefficient. The writers by no means propose that this proves that the shrinkage of the wires is due to self diffusion but we merely wish to point out that there are explanations other than that given by the authors. In this, as in any kinetic phenomena, it is necessary to study the rate of the process before anything can be said about the mechanism. The determination of surface tension given by the authors is based upon an interpretation of the data which embody the concept of viscous flow. The final proof of this concept will be obtained only after the time relationships confirming the authors' Eq 15 have been conclusively established. The rough linearity of the stress strain curves obtained by the authors for experiments run the same length of time should not be considered as proving that viscous flow is occurring. H. UDIN (authors' reply)—All of the test specimens were annealed at 1000°C for an hour or more before preliminary measurements were made. During this anneal the wires recrystallize, and the greatest part of grain growth takes place. Also, the knots sinter at the cross-over points. This does not in itself eliminate the possibility of end errors, although it greatly decreases their probable magnitude. It is still possible that some extension occurs due to creep in shear at the sintered points. If so, this effect would be quite independent of and superimposed on the normal shrinkage or extension of the wire itself. Within the precision of the experimental results, straight lines satisfy the data as well as do any other simple curves. Until data of greater precision are obtained, it is futile to discuss any possible trends away from linearity. The disagreement between Kuczynski and Alexander's Eq 19 and our Eq 18 is one of semantics and mathematics, not mechanism of flow, since Eq 18 is based on the self-diffusion concept of viscous flow. It would be interesting to learn how the mathematics leading to Eq 19 deviates from that of Eyring and of

Jan 1, 1950

By Fred C. Bond

MANY grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.1 The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1 1/2 to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six 1 1/4-in. diameter and two 1 3/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5° for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus 1/2-in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication3 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1947

By R. L. Hadley, G. Derge

The amounts of oxygen in liquid iron-titanium alloys up to 50 pct Ti were measured and the oxide phases in equilibrium with these alloys were determined by using TiO² crucibles. A minimum of about 0.003 pct 0 occurs at less than 1 pct Ti. The various liquid and solid oxide phases can be arranged on a ternary isotherm. THREE characteristics of titanium contribute to the interesting aspects of its reaction with oxygen in liquid iron: 1—It forms a number of stable oxides. 2—All oxides have large negative free energies of formation. 3—The pure metal exhibits high solubility for oxygen. In addition, the use of titanium as a stabilizing and strengthening element in alloys suggests a need for investigation of its reactions in amounts greater than those normally required for deoxidation. These higher compositions are also of interest because they occur during the addition of ferroalloys and produce deoxidation products before dilution is achieved. Titanium Deoxidation in the Literature While the use of titanium as an alloying element and deoxidizer has been common for several decades, the first detailed study of its deoxidizing characteristics was carried out by Wentrup and Hieber' in 1939. These authors determined the extent of deoxidation possible with titanium and identified, by microscopic examination, the products formed. They found that titanium in excess of 0.2 pct did not reduce the oxygen content of iron below 0.004 pct at 1600°C. They identified the spinel FeO-TiO² at low titanium concentrations and Ti2O³ in melts containing more than 0.2 pct Ti. A portion of the area surveyed by Wentrup and Hieber has been investigated recently by Evans and Sloman² using X-ray diffraction for inclusion identification. They concurred in general with the findings of Wentrup and Hieber, but reported the existence of Ti³O5 as a deoxidation product in the range near 0.1 pct Ti. Comstock, Urban, and Cohen³ discussed the deoxidation of iron with titanium, correlating the data of Wentrup and Hieber with free-energy data for the titanium oxides. Scatter at high titanium values was considered attributable either to the formation of an oxide exhibiting high solubility in liquid iron or to the entrainment of solid oxide particles leading to high apparent solubility. Chipman' has calculated the deoxidation curves for titanium based on free-energy data for titanium oxides. These calculations (Fig. 1) and those of Comstock, Urban, and Cohen involve assumptions as to the activity coefficients of oxygen and titanium in liquid iron, since such data have not been determined. Investigation of the deoxidizing characteristics of chromium" and vanadium0 have shown that these elements decrease the activity coefficient of oxygen in liquid iron, leading to a tendency toward relatively high oxygen values and experimental scatter in highly alloyed melts. Experimental This investigation involved two major objectives: 1—determination of the composition of the oxide phases in equilibrium with liquid Fe-Ti alloys, and 2—establishing the pattern of oxygen solubility in liquid Fe-Ti alloys at titanium concentrations in excess of that required for attainment of minimum oxygen content. Raw Materials Ingot iron was used having the following composition: 0.02 pct C, 0.017 pct Mn, 0.01 pct Si, 0.02 pct S, 0.006 pct P, and 0.03 pct 0. The titanium used

Jan 1, 1956

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By Tracy L. Atherton

The mapping of slant-hole oil fields is complicated by the fact that relationships between wells are subject to variations in three dimensions and are not readily adaptable to representation on a plane surface. Formalized perspectives usually expand into an undecipherable maze of lines and peg models with the necessary supporting dividers serve only to awe the beholder with their perplexity. The usual compromise arrived at is a plotting of the projection of the courses of all of the wells in the field onto a horizontal plane (Fig. I). These complicated plots, when used in conjunction with the individual vertical projections of the wells, heretofore have been the most practical foundation for the study of general field problems. This method has many shortcomings, however, which arc not found in the recently developed straight-hole equivalent projec-tion method. The new method supplies a series of maps similar to the type now in common use in straight-hole fields. It is remarkably simple to use and supplies a ready check on clearances between wells. Perhaps the method can best be understood if the steps that led to its development are described. Common practice of oil-well surveyors is to supply the owner with a tabling of the survey and a plan view plotted against the true meridian. If a vertical projection is plotted, it is usually plotted separately and shows vertical depths against the projection of the stations along a section line joining the top and bottom of the hole on the plan view. A more practical method would be to plot the section line of the plan parallel to the abscissa of the vertical projection (Fig. 2). If this is done, any line parallel to the "base line1' will pass through the points on each projection that represent a single point in the hole. Another very useful graph, which the well surveyor could provide, would be plotting of vertical depths against measured depths. Fig. 3 illustrates the next step facilitated by this form of plotting. The lines designated "well A" represent the proposed course of a hole to be drilled. Superimposed on the drawing, in its proper relative position, is the plan view and a portion of the vertical projection of a present producer, well B." From an inspection of the plan view we arrive at the correct conclusion that the only indicated possibility of collision is at the point of crossing of the wells on the plan view. Referring to the vertical projection, note that the vertical depths of stations on B, in the vicinity of the crossing, are plotted on the same plane of projection as A. The clearance is the indicated distance between the two vertical sections measured along the parallel to the "base line," which passes through the point of intersection of the plan view. Repeat this process for the other wells crossing the proposed course of A on the plan view and you have a preliminary check of clearance for the proposed course. A similar comparison of crossings on the vertical projections of all >

Jan 1, 1941

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,1 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental rig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.* In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

By Tracy L. Atherton

The mapping of slant-hole oil fields is complicated by the fact that relationships between wells are subject to variations in three dimensions and are not readily adaptable to representation on a plane surface. Formalized perspectives usually expand into an undecipherable maze of lines and peg models with the necessary supporting dividers serve only to awe the beholder with their perplexity. The usual compromise arrived at is a plotting of the projection of the courses of all of the wells in the field onto a horizontal plane (Fig. I). These complicated plots, when used in conjunction with the individual vertical projections of the wells, heretofore have been the most practical foundation for the study of general field problems. This method has many shortcomings, however, which arc not found in the recently developed straight-hole equivalent projec-tion method. The new method supplies a series of maps similar to the type now in common use in straight-hole fields. It is remarkably simple to use and supplies a ready check on clearances between wells. Perhaps the method can best be understood if the steps that led to its development are described. Common practice of oil-well surveyors is to supply the owner with a tabling of the survey and a plan view plotted against the true meridian. If a vertical projection is plotted, it is usually plotted separately and shows vertical depths against the projection of the stations along a section line joining the top and bottom of the hole on the plan view. A more practical method would be to plot the section line of the plan parallel to the abscissa of the vertical projection (Fig. 2). If this is done, any line parallel to the "base line1' will pass through the points on each projection that represent a single point in the hole. Another very useful graph, which the well surveyor could provide, would be plotting of vertical depths against measured depths. Fig. 3 illustrates the next step facilitated by this form of plotting. The lines designated "well A" represent the proposed course of a hole to be drilled. Superimposed on the drawing, in its proper relative position, is the plan view and a portion of the vertical projection of a present producer, well B." From an inspection of the plan view we arrive at the correct conclusion that the only indicated possibility of collision is at the point of crossing of the wells on the plan view. Referring to the vertical projection, note that the vertical depths of stations on B, in the vicinity of the crossing, are plotted on the same plane of projection as A. The clearance is the indicated distance between the two vertical sections measured along the parallel to the "base line," which passes through the point of intersection of the plan view. Repeat this process for the other wells crossing the proposed course of A on the plan view and you have a preliminary check of clearance for the proposed course. A similar comparison of crossings on the vertical projections of all >

Jan 1, 1941

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,1 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental rig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.* In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

By E. Gybbon Spilsbury

In a paper* read at the last meeting of the Institute, in Scranton, Pa., I referred to the proposed introduction at the Haile gold-mine, South Carolina, of a novel method of chlorination. I have since

Jan 1, 1888

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations.

Jan 11, 1950