Search Documents

By Lawrence Addicks

Some three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed by constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and was fired with fuel oil. A run of several hours yielded excellent nodules. The ki1n showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal, of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per ton of flue dust shown on the test and as fuel oil at that time was selling around 2 1/2 c. per gallon it was decided to let it go at that. A 60 by 6 ft. kiln was decided on, as that size is standard in cement practice, although fast being replaced by much larger ones with their greater fuel economy, and as it fitted in the building space available. A 6-in. brick lining brought the net diameter down to 5 ft. The inclination

Jan 1, 1915

JOHN H. NELSON, Worcester, Mass.-At our plant we have done considerable work on notch-bar testing and are farther at sea now than when we started. So far, we have been unable to get the notch-bar test to be consistent with any other known test. Lately, I have been investi-gating the effect of the position of the notch-bar specimen in a, bar. To do this I took a 3, ½ in. square bar and quartered it, then heat treated the four quarters. Each of these pieces was again quartered and a specimen machined and notched. "In this way we would have notch-bar tests from the exterior to the interior of the bar. These were made of such lengths that it was possible to make four impact tests on each speci-men. Extreme care was taken in marking the position of these test speci-mens in the original bar. The notches were then cut with relation to position of the specimen in the original bar. The second notch was cut 90° from the first, and so on around the specimen. In this way, we have found that, with a 3 ½ in. bar of 0.4 or 0.5. per cent. carbon steel when properly heat treated, we could get impact values ranging from 15 to 100 ft.-lb. Just why this is the case we are unable to state; but it does appear to be a fact that along the outside of the original bar the notch-bar test seems to be low and increases toward the center, but it is not always consistent. For instance, we may have, on a single specimen; one notch-bar test giving us 15 ft.-lb. and another 100 ft.-lb. We have not found such inconsistencies in alloy steels. Alloy steel is consistently good or consistently bad. If it. is good, you cannot readily destroy the impact value, no matter what you do; if it is bad-that is, if it is a poor notch-bar steel-and you have sufficient latitude in your draw, you may correct it. In other words, if the hardness you are working to will allow you to draw to about 1050° F.(561° C.) or over and then quench this steel from the draw heat, you. can raise the im-pact value of the steel from about 4 or 10 ft.-lb. up to-40-or 50 ft.-lb: Just what occurs I do not know. There is evidently a critical-point in steels that have poor impact value, in the neighborhood of 1000 F. to 1050° F. (536° to 561° C.).

Jan 12, 1919

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades: I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. I t is a fact which many of you can certify to, that we are wasting fully me-half of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth . below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

By T. Koulomzine

The theory of the Askania mag-netometer, as well as a complete discussion of all factors influencing magnetometer readings, is very ably described by J. Wallace Joyce.1 We will assume that the reader is thoroughly familiar with this theory and we will use whenever possible the same notations for the physical values involved in the theory. On the other hand, we believe that the principal formulas of the magnetometer can be deduced much more easily by the use of differential calculus than by the methods employed by Joyce. Consequently, we are presenting herewith a resumé of the theory of the vertical magnetometer in order to determine the correct formula of the temperature coefficient which we propose to compensate. Short Theory of the Vertical Magnetometers We shall accept the following notations: m = total mass of the magnet system, in grams. g = acceleration of gravity, in dynes. a = projection on the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. h = projection on the perpendicular to the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. M = 2pL = M, magnetic moment of the magnet system. Z = vertical component of the earth's magnetic field. ? = deflection angle of the magnet system. = focal length of objective lens in the optical system S = scale reading. In a vertical magnetometer the axis of the magnet system is kept horizontal within 2". Therefore, referring to Fig 1, we see that the magnetic torque of the magnet system influenced by Z must be counterbalanced by the gravity torque. MZ cos ? = mga cos ? + mgh sin ? or dividing by cos ? MZ = mga + mgh tan ? If we now move to another magnetic station and the temperature conditions change, the values of all the variables will change also: M, a, and h under the influence of temperature. 2, both with time and space. ? and S, as a result of all the above changes. Taking increments in Eq 2 we obtain: (Mo + ?M)(Z + ?Z) = mgao + mg?a + mg(h + ?h) tan (? +??) but tan (? +??), because ? is small, can be replaced by tan ? + tan ??; in fact tan (?+ ??) = sin ?.cos ?? + cos ?.sin ??/ cos ?.cos ?? — sin ?sin ?? but sin ? sin ???0 tan (8 + ??) ? tan ? + tan ??. Fur-thermore, neglecting all terms of the equation containing two differentials becomes: or a differential and a tan ??, Eq 3

Jan 1, 1950

By G. Lavagnino

The old Telegraph mine lies on both sides of Bear gulch, a short branch of Upper Bingham canon, and nearly in the center of the group of mines called the Bingham Mines, about twenty-seven miles southwest of Salt Lake City. It is considered, by local miners as the most important mine of the district. The geological formation consists of Weber quartzites, with subordinate conformable limestones and shales, alternating with porphyritic rocks. These widen towards and connect with the massive backbone of the Oquirrh mountains, while the quartzite develops itself on the slope broken through by Bingham canon. The porphyry not only runs between the strata, but also cuts across them, isolating large portions near the mountain mass, and again on a smaller scale it penetrates some joints in the quartzite. It is a crystalline felspathic rock, containing variable proportions of quartz, mica, hornblende, chlorite, and iron pyrites as accessories. In places, it takes a less distinct or almost uniform fine-grained structure. It has a gray or greenish, and, when much altered, also a reddish or even white color. The quartzite is a fine-grained or almost compact grayish-white or bluish or reddish quartz-rock, containing in places fine scales of mica and grains of iron pyrites as accessories. The raised, folded, or broken masses show well-defined bedding-joints, and their general dip is 35 to 50 degrees towards north or northwest. In the porphyry occur metalliferous veins with a prevailing N.E.S.W. strike. These are in general narrow veins; their principal contents are not dissimilar from those of the other deposits; but there is considerably less oxidation near the surface and the ore is mostly richer in silver and gold. In the quartzite the ore-deposits generally occur on the joints of bedding. The more important deposits occur either in clearlydefined contact-veins or, more often, in somewhat vaguely-defined mineralized zones, that could be called contact-zones. These comprise several masses of more or less altered or decomposed rocks and the newly-distributed products of their mechanical and chemical decomposition, such as breccia and clay in seams or in more irregular bodies..

Jan 1, 1888

By Arthur Hixson

ALTHOUGH a few engineers have recognized the problem of the mechanism of filtration it has never been studied in a quantitative way. A background for a better understanding will be afforded by a survey of certain fundamental principles of filtration. In recent years, authorities have become practically unanimous in saying that the actual filtering should be done, not by the cloth itself, but by a layer of solid particles deposited upon it. Thus, a cloth may be used in which the openings are considerably larger than the particles to be filtered, provided that groups of particles form an arch or bridge over each opening. This can be accomplished if the initial pressure is so low that the arch will not be broken while it is still thin. According to Wright,1 the chief advantage of this method of filtration is that the open-weave cloth does not become clogged as easily as does one of closer weave, where the fine particles often work their way into the interior of the cloth and become caught there. If the character of the material to be filtered is such that it will not form a good film, then it becomes advantageous to use "filter aids" for pre-coating the cloth with a desirable layer of solids, and the coating need be only of a very slight thickness for good results. Until the film is formed, the first runnings of the filtrate may be cloudy, often necessitating refiltering this portion. A factor which has considerable effect on the performance of filters is the concentration of solids in the pulp. According to Wright, a. high concentration of solids gives a porous cake, since the flow is then slower than with- a thin pulp. The porosity of the cake is also affected by the pressure: a high initial pressure tends to compact the cake, and the same effect results from fluctuations of pressure. In his studies of the relation between pore size and particle size, Hatschek2 observed that the particles in a pulp tend to arrange themselves with maximum cross-section parallel to the direction of flow and that this is more marked at the higher velocities. Thus, at high pressure and high velocity, a certain pulp

Jan 2, 1926

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

By D. Cubicciotti

IT has long been known that some metals are capable of being dispersed or dissolved in certain of their fused salts.' Davy' and Bunsen³ were among the first to observe that in some fused salt electrolyses, a highly colored, strongly reducing salt phase appeared in the neighborhood of the cathode. Later workers found that the current efficiency of the electrolysis was markedly reduced when such a phase appeared. It was also found that the strongly reducing salt could be made by melting the metal and normal salt together. Chemical analysis showed that in such salts the metal ion to anion ratio was always larger than in the normal salt. From such observations arose two different explanations of the nature of metal in salt solutions. When a solution of this type is quenched, it is possible to find small globules of metal in the salt. From this and other observations, Lorenz' and co-workers assumed the metal in salt solution to be a colloidal dispersion of metal in the fused salt and called it "metallnebel" or metal fog formation. They made a number of experiments to substantiate this point of view. Another school felt that when the metal dissolved it reduced the salt partially to a mixture or solution of normal salt and subsalt. Both of these ideas could explain the strong reducing character of the salt formed and the low current efficiency of the electrolysis. If either a metal colloid or a subsalt were formed at the cathode and diffused to the anode, it would be oxidized to the normal salt. Thus a cyclic process of oxidation and reduction could be set up conducting the current without giving rise to a net change in the system. These facts led the author to investigate some of the properties of metal in salt solutions with the hope of elucidating their nature further. Among the metal-salt systems that form metal in salt solutions most markedly are the alkaline earth metal-halide systems and cerium, bismuth, and cadmium halides. Other systems of halides, oxides and sulphides form such solutions to a lesser degree. The first work undertaken was a study of the temperature-composition diagrams of some of the systems." From such diagrams it would be possible to distinguish between a subhalide formation or a colloid. A subhalide should give rise to characteristic changes in the phase diagram, while a colloidal dispersion of metal in salt would not alter the freezing point of the salt. The results obtained on a number of alkaline earth metal-halide systems were all quite similar. Fig. 1 shows the barium-barium chloride system. The other

Jan 1, 1954

By J. D. Wheeler, H. W. Mathews

The increased activity in West Texas, which started in 1933, has continued through 1936 at a constantly accelerated rate. During 1936 there were 1442 wells completed in the area as compared with 700 in 1935 and 468 in 1934. Of these completions, 1313 were producers with a total 24-hr. potential in excess of 1,750,000 bbl. From among the 1442 wells, eight are considered to be discovery wells for new West Texas fields. New Fields Bennett.—The Bennett field, which added Yoakum County to the oil-producing counties of West Texas, was actually indicated as an oil-producing area during 1935, but the discovery well, Honolulu Oil Corporation, Ltd. and Cascade Petroleum Company's Bennett No. l, was not given a production test until April 1936. The discovery well made 15 bbl. per hour through 3/4-in. choke with a plugged-back total depth of 5264 ft. First oil in the hole was from 5088 to 5090 ft., which is several hundred feet below the top of Permian lime. Producing limits of the field are unknown, as the second test had not reached the pay at the close of the year. Henderson.—-To date indications are that the Henderson pool, in northern Winkler County, is the most prolific area opened during 1936. This field, which lies to the north of the old Hendrick pool, is producing from the same reef-type dolomitic lime producing in the older field. The Henderson field was opened by the completion of R. H. Henderson, J. B. Walton-Humble 1-A in April 1936 for a natural flow of 2306 bbl. per day through tubing. Total depth of the discovery well is 3049 ft. Later development has indicated the productive area to be a rather narrow zone running slightly west of north. Present area of from 1000 to 1500 acres has been proved for production. Keys and Emperor.—The Keys and Emperor pools in the belt of sand pools running across Winkler County appeared for the first time on State proration schedules during 1936. This report considers these pools as links in joining the belt of sand production across Winkler County, for

Jan 1, 1937

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By A. L. Holley

THERE is a growing demand for pure and cheap material for fine open-hearth steel ; a material not only very free from phosphorus, but from carbon and silicon; so that it may he rapidly converted into steel. Iron and steel scrap are not trustworthy as to quality, and they are often dear. There are three methods of purifying cheap materials for the open hearth. 1. Mechanical puddling, as done at Creusot, which removes 90' per cent. of the phosphorus from the pig iron. 2. Krupp's washing process (the conduct and results of which I fully described in a former paper*), which eliminates 70 to 80 per cent. of the phosphorus and most of the sulphur and silicon from pig iron. Neither of these processes would sufficiently purify, for very fine steel, those very impure pigs which are cheapest in many parts of the United States: 3. The process of producing directly from the ore an iron which is practically pure chemically, although mechanically mixed with the impurities of the ore. This is the oldest of iron processes ; one form of it, the Catalan forge, employed to produce charcoal blooms, is still in use, but its great cost is rapidly throwing it out of competition. Among the modern attempts to produce iron direct from the one, on a large scale and at a cheap rate, several have been in various respects successful. Dr. Siemens's process of treating a ton and a half or more of ore and the coal to deoxidize it, in a rotating gas furnace, and bringing out, in some four hours, a ball of chemically pure iron so soft that the fluid and impure slag may be squeezed out of it, is the most attractive and the most highly developed of all the modern direct processes. I have watched it, from time to time, since 1874, and have noted a steady improvement. It may now be said to have passed the experimental stage, although, like older processes, it must be adapted by practice to special materials. The cause which has been more potent than all others, including the defects of the best direct processes, to bring these processes into disrepute, is the waste-ful treatment of the direct product. With one or two exceptions (when failure was due to other and obvious causes), the direct product has been made into wrought iron (weld iron). Even Dr. Siemens has, at Towcester, in England, and at Park, Bro. & Co.'s, in Pittsburg, set up his apparatus for this purpose. Is it likely that

Jan 1, 1880

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By K. R. Van Horn

RESIDUAL stresses in metals operate under a cloak of mystery, as they have neither been seen in the laboratory nor detected by means of the microscope. In spite of their phantom-like nature, they frequently exert metallurgical effects that cannot be ignored. In some cases the results have been detrimental, causing rejections or premature failures, but frequently the effects have been highly beneficial to the producer or consumer of metal products. First, however, what is a residual stress? When a metal is plastically deformed by bending, rolling, pressing, or by a phase transformation or precipitation from solid solution, or by a sharp temperature gradient resulting from nonuniform cooling, quenching, or welding, it remains in a state of strain. The strains or strain gradients produced by such operations and retained after all external forces are released are known as residual strains, and the accompanying stresses as internal or residual stresses. Many defects or failures in metal products have been ascribed to residual stresses, sometimes erroneously, because there was no other apparent explanation after the usual metallurgical tools of diagnosis had been applied. For example, during World War 11, the forged aluminum alloy aircraft cylinder head in the reciprocating engine began to replace the cast head with the familiar cooling fins. The fins were machined in the solid forged head by an ingenious milling operation. One plant reported an epidemic of excessive distortion during the delicate high-speed milling. A thorough examination revealed that the composition, heat treatment, mechanical properties, and metallurgical quality of these heads were comparable to those of forgings that machined satisfactorily. It was then claimed that the cause of the machining difficulties was connected with residual stresses resulting from the quenching during the solution heat treatment. An elaborate stress analysis actually demonstrated, however, that the magnitude of residual cooling stresses was lower in the cylinder heads which machined poorly than in those which were satisfactory in this respect. Subsequent tests proved that the machining problems in this case originated from variations in the tools and tool design. Sources of Residual Stresses in Metals Residual stresses are of two origins—mechanical and thermal. Thus, stresses may be produced in a metal by any cold-working process. The distribution and magnitude of these mechanically produced stresses can be calculated in a satisfactory, although approximate, manner for such simple cases as bending, torsion, and expanding of tubes. However, most manufacturing processes are too complex, and the original stress-strain relations in the products are not sufficiently known to permit calculation of the resulting residual stresses. Also, a specific process, such as wire drawing, may vary in complexity or uniformity of working, and large or small residual stresses may result, depending on the conformation of the dies and other features of the working process. Neither substantially unidirectional deformation, such as can be imparted by stretching a metal product having essentially the same mechanical properties throughout the cross section, nor deformation

Jan 1, 1954

By W. N. Best

This paper is not intended as a scientific discussion of the combustion of oil but is written from the standpoint of an operator who has the experience and qualifications necessary to guide others in producing the most economical results in the use of liquid fuels. Oil, in this paper, usually means petroleum or its products but incidental reference is made to other liquid and gaseous fuels, so that the term may be considered as referring to all liquid and gaseous hydrocarbons in comparison with solid fuels, as coal and wood. However, only a few of the principal factors in the use of oil as a fuel can be given. The present, and prospective, high price of coal is causing users of fuel to renew inquiry as to the merits of other forms of fuel for industrial purposes. Crude oil (petroleum) is proving to be one of the world's most valuable mineral resources. The recent discovery that oil underlies a considerable area of the United States, Mexico, and other parts of the world to a greater extent than was formerly believed and the large production of some of the wells in these areas shows the probable quantity of fuel oil that may now be available. Through the energy of Lord Cowdrey, who was one of the pioneers of the oil industry in Mexico, oil has been discovered in England; some prominent geologists believe that it may be found in quantity in Great Britain. For years, oil has been known to be of great value in the manufneture of metals. It has proved incomparable in forge shops, steel foundries, heat-treating furnaces, and wherever accuracy of temperatures is essential, or where a maximum output is desired as well as quality of metal. In some types of equipment, the output produced with oil as fuel is double that obtained with coal and at a reduction of 50 per cent. in the cost of the fuel. For example, in drop-forging plants, the metal is always waiting for the man when oil is used as fuel, whereas with coal, the man must wait for the metal to become sufficiently heated. It has only been since January, 1919, that the oil supply could be relied on for boiler service, owing to the war conditions and the inability to get oil tankers for the delivery of the oil from Mexico to Atlantic ports; but now a constant supply is assured, and many manufacturers are installing it in their power plants. The cost varies with the size of the

Jan 1, 1921

By P. Duwez, L. Zwell

In recent years, the problem of pressing metal powder in a die has received much attention. The question has been the object of a Symposium held in New York in March 1947 under the sponsorship of the AIME; an excellent review of the subject may be found in Ref. 1. Various experimental techniques have been used to study the behavior of the powder in a die cavity. Two methods have been particularly successful; one consists of measuring the density distribution²,³ and the other makes use of a lead grid in the powder during pressing.4 In the present study, the pressure at various points on the bottom and the sides of a die 1.50 in. in diam was measured by means of small piston dynamometers and resistance sensitive strain gauges. In order to correlate the results with previous investigations, the pressure distribution inside the compact has also been determined by an indirect method based on density measurements. Strain Gauge Measurements of Pressure on Side and Bottom of Die A schematic drawing of the die used for measuring side pressures is shown in Fig 1. The pressure gauge consists of a 0.25-in. diam piston A which transmits the pressure to a dynamometer B, on which two Baldwin Southwark type 4-14 strain gauges are fastened 180" apart. Because the installation of several dynamometer assemblies along the side of the die would have been difficult, the pressure distribution was obtained in successive tests in which the distance from the gauge to the bottom of the compact was adjusted to different values by changing the length of the bottom piston. The dynamometer, disassembled from the die, was calibrated under compressive loads and showed a 1.00 ohm change of resistance for every 15,300 psi change of pressure (750 lb load change). All the strain gauge measurements were made with a null type Leeds and Northrup Wheatstone bridge. The sensitivity of the method was better than 1 pct and the accuracy was within 2 pct. These values were considered satisfactory in view of the rather large scatter in the measurements introduced by the random variation in packing the powder in the die. The stable ambient conditions and short time involved in the taking of observations made temperature compensation unnecessary-. The pressure distribution on the bot-

Jan 1, 1950

By Robert H. Richards

THE Institute of Mining Engineers has shown so much interest in the educational problem of profitably combining theory and practice, that it seems especially appropriate to lay before its members the methods and aims of the mining laboratory of which I have charge, and in which one form of combination of hand with head work is now being tried. If anything may be contributed toward the solution of this problem by the discussion which follows, my purpose mill be attained. Whether it was wise or not to establish a mining school so far from the principal mining centres, does not now enter into the question. Given, a mining school already begun, how shall it be made most efficient in developing engineers who are trained to think for themselves as well as versed in the works of others ? This is the question with which we have had to deal. In considering the bearing of this laboratory work upon the students' preparation, it will be convenient to take it up under five different heads: 1. The methods and aims of the laboratory. 2. The advantage to students of having a part, at least, of their practical work in the curriculum of their school. 3. The advantage to be derived by mine; and works. 4. Degree of accuracy which may be attained in working ores on a small scale. 5. Reslts of work in the laboratory. 1. The Methods and Aims of the Laboratory.—During the May meeting of 1873, held in Boston, I had the privilege of reading before you a paper stating the plan; and aims of this laboratory. Since that time me have been constantly following out those plans, and are more than ever convineed that me are working in the right direction. We do not feel that the time we have spent has been in any sense thrown away. Perhaps the aims of the laboratory can be most clearly shown by illustration. Many young engineers have school thinking that they know everything. They go to the works, and expect to teach the superintendent something and the men a good deal, regardless of the fact that it is this spirit that has prejudiced workmen against schoolmen. They are often more trouble than they

Jan 1, 1879

By Reuben B. Ellestad, Fremont F. Clarke

Lithium chemical plant extraction methods are discussed with reference to 1) base exchange with alkali sulphates; 2) processing based on roasting with lime; 3) miscellaneous methods; and 4) application of the Lithium Corp. process to extraction of lithium from run-of-mine, low grade spodumene ore, or concentrates. IN the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2SO4) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K2SO4 is objectionable from cost considerations since purification of lithium carbonate requires the use of potassium carbonate, if the K2SO4 is to be recovered and recycled. The lower solubility of K2SO4 as compared with Na2S04 is also objectionable, since it limits the concentration of the Li2SO4 solution to be precipitated by K2SO4. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging. Other related base exchange processes are those of Lindblad, Wallden, and Sivander3 and Sivander, Gard, Villestad, and Wallen4. The former covers the reaction of lithium silicate minerals with a sodium sulphate solution, at 100" to 300°C (under pressure), while the latter involves the extraction of silicate minerals with molten sodium sulphate. Both these processes would seem to be difficult and expensive to operate.

Jan 1, 1956

By H. H. Vogel

THIS paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. CHARACTERISTICS OF THE ORE The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾ mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3A12 (Si04)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to 12 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crystals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3.07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive. FORMER OPERATIONS Mining operations have been carried on for 60 years. Until 1023, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By J. R. Cahoon, W. V. Youdelis

In a previous communication by one of us,1 a theory of inverse segregation was presented by which the maximum segregation and segregation distribution throughout a unidirectionally solidified, binary-alloy ingot could be calculated. The theory, which is based on the mechanism of volume contraction and interdendritic flow, quantitatively accounts for the observed maximum segregation in the A1 (rich)-CU' and Al-Zn2 alloy systems, and for the segregation distribution along the ingot lengths for the A1-Cu system.''4 One of the drawbacks to a more extensive use of the segregation equations is their complexity, particularly for the calculation of the segregation distribution throughout the length of the ingot, involving long tedious numerical calculations to obtain the segregation. Computer pro- grams, written in Fortran II for use on an IBM 1620 computer, have been developed by the authors (and are available from them), providing quick and accurate methods for the determination of the theoretical maximum segregation in any binary-alloy system, and also for the segregation distribution in any unidirectionally solidified binary-alloy ingot. The segregation distribution is controlled by the lengths of the various solidification zones'74 which are in turn controlled by the cooling rate, and are determined from temperature-distribution curves obtained during solidification. The theoretical segregation distributions shown in Fig. 1 illustrate the effect of the zone lengths on the distribution Curve 1, indicative of a slowly cooled ingot, represents an ingot having long solidification zones, while Curve 2, indicative of a rapidly cooled ingot, represents an ingot having relatively short zones. Although these distributions are calculated for an A1-10 pct Cu ingot, the shape of the distribution would be similar for any binary-alloy ingot. These curves show clearly why early workers obtained results which indicated that the maximum (chill-face) segregation approached zero at very fast cooling rates.3 Actually, the maximum segregation is independent of cooling rate,' but even at short distances from the chill face the amount of segregation drops considerably, particularly in a rapidly cooled ingot, making it very difficult to establish the amount of segregation occurring at the chill-face. The authors would like to thank Dr. J. A. Goldak for his assistance in the preparation of the programs. The financial assistance of the Steel Co. of Canada and of the National Research Council of Canada in the form of Scholarships to one of us (J. R. Cahoon) is gratefully acknowledged.

Jan 1, 1964