Search Documents

By Franc R. Joubin, D. H. James

Uranium exploration in the North Shore area of Lake Huron goes back to 1847 when J. L. LeConte, a distinguished American geologist, identified a pitchblende-like mineral which he called coracite from specimens sent from a locality north of Sault Ste. Marie. In 1948 a search for the LeConte occurrence resulted in discovery of the Camray field, some 70 miles north of Sault Ste. Marie. Prospecting the Camray field yielded about 30 pitchblende occurrences spread over approximately 200 sq miles. Almost without exception these discoveries consisted of narrow, short, pitchblende-filled fractures, within or along the contacts of diabase dykes cutting pre-Cambrian Archean granite and gneiss. Eight discoveries were diamond drilled and three were explored underground, but none proved to be of economic value. Uranium prospecting at this time spread far afield, and it was in 1949 that radioactive conglomerate was discovered in Long Township of the Algoma district midway between and 90 miles from Sault Ste. Marie and Sudbury. F. Joubin examined this discovery at that time but could not interest capital in its development.

Jun 1, 1956

By Edward Halse

Normal banded structure,* exhibiting bands or layers of mineral symmetrically arranged from the sides to the center of the vein, appears to be by no means common in the Republic of Mexico. When the bands of quartz form interlocking crystals in the center (" comb-structure "), the evidence that the filling has taken place in an open space is complete. This also applies in the case of any mineral the fibers of which are perpendicular to the walls, and which presents here and there, in a central line, cavities or vugs lined with crystals (geodes); but it does not follow that the whole width of the banded vein represents that of the original open fissure. The opening and filling may have been slow and gradual processes, advancing

Jan 1, 1902

By T. Reed Scollon

With some uncertainty as to the type, rate and scope of adoption of air pollution control regulations, and with limited information on the availability of low-sulfur fuels, it is possible at best to make only a rough assessment of the impact of such regulations on coal. It is apparent from the following discussion that regulations of the type already effective or being considered, if adopted and enforced on a widespread basis over a short-term period and if substitute fuels were available, both quantitatively and economically, could result in a loss of more than one-half of coal's markets. Depending on the areal sequence of adoption of such regulations, some areas would be able to obtain limited amounts of low-sulfur coals. Others would not. Because of the usually greater distances from the large industrial coal consuming areas to new sources of coal supply, and because of the higher mine prices for low-sulfur coals, the delivered prices of such coals as might be available would be much higher than those for high-sulfur coals. A large and sudden demand for low-sulfur coals would exert further upward pressure on prices.

Jan 1, 1970

Optimism over the continued growth of coal ex- ports received a significant shot in the arm September 18 at Norfolk, Va., when huge, new ship coal-loading facilities of the Norfolk & Western Railway were formally dedicated before a large audience of American and foreign dignitaries. Guest of Honor at the occasion was Christian A. Herter, Special Representative for Trade Negotiations, who, in a speech, stated, "The prospects for the expansion of our coal exports are excellent. The competitive pricing and high quality of our coals, whether for the production of coke for steel mills or for the generation of electric power, have won the respect of consumers everywhere in the world. Last year, the United States coal industry exported over 40 million net tons. . . . There are excellent reasons to believe that by 1970 we shall be exporting at double this rate."

Jan 10, 1963

By C. B. Barlow, T. A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 stph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1986

By Stanley Herold

AT THE present time five localities in the Argentine Republic are known to bear direct evidences of the presence, of petroleum. The segregation of these localities is more or less arbitrary inasmuch as minor indications may be found to extend from one locality to the other at no regular distance apart, especially in the northern and western part of the republic. These localities are listed as follows: North Argentine-Bolivian region, Salta-Jujuy district, provinces of Mendoza and Neuquen, Comodoro Rivadavia, and the Gallegos-Punta Arenas region. Economic conditions attract us to the possibilities of developing these and other regions of countries in the southern hemisphere. Development work will, naturally, be undertaken first in such localities as present direct manifestations of the presence of petroleum; "hidden fields" may exist, but, unless discovered by accident, their development will be left to the last. The problems to be solved in the development of the petroleum resources of the Argentine republic are mainly of stratigraphy, structure, and transportation. We are not here concerned with the unfavorable climate of the countries to the north in the tropics where, for us of the "far north," life hangs by a thread ready to be severed by a mosquito, gnat, or tropical germ.

Jan 2, 1920

By R. L. Templin

THE modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 lb. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately correct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements.

Jan 1, 1930

By M. J. Salkind

In discussing the possible contribution of plastic deformation to neck growth during sintering, Wilson and Shewmon State that Lenel, Ansell, Salkind, and Early34, 35 concluded that dislocation flow is the rate-controlling process in sintering under zero external load. The experiments cited34, 35 were done with applied external loads, and the conclusions were that the same kinetics could be controlling sintering due to the force of gravity with no additional applied load. The effect of gravity on sintering behavior was previously cited.34, 31 In addition, Wilson and Shewmon argue that the conclusions of Refs. 34 and 35 are doubtful because the strain rate is proportional to stress for plastic flow. This assumption is true only for certain kinds of plastic flow such as Nabarro-Herring Microcree38 As Early, Lenel, and Ansell point out3' plastic flow, based upon dislocation movement, can exhibit strain rates which exhibit a power law relationship to the applied stress.39, 40 Wilson and Shewmon also doubt the results of Refs. 34 and 35 because the stresses in the necks are too small for x/a > 0.1. This is true, and the experiments described in Refs. 34 and 35 were done for small values of %/a. The conclusion was that plastic flow by dislocation movement was important during the early stages of sintering when x/a is small.

Jan 1, 1968

By H. Martyn Chance

I have been induced to present this paper to the Institute because I have been unable to find any publication containing a disctission of this subject. In some of our technical schools and colleges the student is required to construct or copy (generally the latter) a number of profile sections as part of his routine work; but little attention is given to the methods of projecting observed dips and exposures upon the section line, and still less to the method of constructing the under (or above) ground curves. As a result of this lack of instruction every engineer or geologist is compelled to invent for himself a system, or copy the style of others. Geological profile sections have frequently been used to determine underground structure from data obtained at the surface, but the experience of engineers in the anthracite coal-fields has shown that they are to be relied upon only in exceptional instances. The possibility of indicating underground curvatures from dipangles observed at the surface has been found to be limited to a mere approximation of the larger flexures, As a means of predicting the depth and shape of minor rolls, they have been found most unsatisfactory. In the anthracite coal-fields the hypothecated

Jan 1, 1881

By W. B. Devereux

I have observed three deposits of iron ore in Pitkin County, which present unusnal characteristics, and wliich seem to throw some light upon the genesis of iron ores under certain conditions. They occur in the precipitons mountain ranges, forming spurs on the Pacific slope of the main continental backbone. The first is a body of limonite, lying upon the side of a high mountain, which forms part of the base of Hayden's Peak. This limonite forms a sheet of considerable area, and is thin at the edges, and about 3 feet in thickness in the central portions. It is conformable with the slope of the mountain side, and rests upou the eroded rocks, but is not comformable to them. The ore is laminated and shaly in texture, and has the physical characteristics of the hard limonites, such as are found in the Marquette District, Lake Superior. It is covered with loose earth and rocks, from 1 to 2 feet in thickness. Much of the ore is filled with impressions of' spruce leaves, such as are found in the forests now covering the slope of the mountain. In the rocks forming the mountain, iron pyrites occurs in bodies, and this limonite probably owes its origin to such a body not far distant. Not far up the mountain large masses of conglomerate are now forming, the cementing material being a similar hydrated oxide of iron. The iron is

Jan 1, 1884

By Charles George, Ronald Faul

The cementing process has been used in approximately 2.5 million oil and gas wells to seal, protect and isolate various downhole formations against communication. It has been adapted to other more specialized situations such as solution mining and sealing salt storage reservoirs. The technical literature contains very few papers specifically dealing with the cementing process for these applications, yet there have been many special projects in various parts of the world that are novel. These will be highlighted in this review. This paper also presents a comprehensive review of the various techniques used in cementing wells drilled for the recovery of soluble salts and brines. It also covers the application of cementing techniques to a large number of wells drilled for the storage of hydrocarbons in South Louisiana.

Jan 1, 1985

By J. J. Kanter

A. I. Blank.*-—Mr. Kanter has spoken of failures from causes other than creep itself in metals that are subjected to creep stresses. Would it be possible for the author to enlarge on this very important matter of "cataclysmic types of failures? " J. J. Kanter.—Of course, it is always a delicate matter to discuss specific failures. I would prefer to keep the present discussion on fundamentals and principles. H. L. Burghof.*—Mr. Kanter, I should like to ask what you consider the responsibility of the designer in avoiding stress concentrations that would lead to these types of failures? J. J. Kanter.—lt was my feeling in looking over the papers of this symposium that they were significantly lacking in consideration of what happens to the metals when strained under conditions that lead to rupture. Often creep tests are run that produce only a fractional percentage of the deformation, in several thousand hours. That kind of information gives the designer no assurance whatever that cracks will not result in his structure at points where stress concentrations, and therefore deformation concentrations, exist. I think anyone in this day and age who presents a paper on creep should incorporate with those studies a thorough investigation of creep rupture if it is expected to make an impression upon the design engineer.

Jan 1, 1945

By the courtesy of Sir Robert Hadfield, we have received the fol¬lowing communication relating to the development and encouragement of science and research in Germany at present. These statements have been translated by Sir Robert from various German sources, and are presented here as an indication of what Germany is doing not only to further her military power, but also to prepare for the period of trade rehabilitation to which she is looking forward after the close of, the war. KAISER WILHELM TRUST FOR PROMOTION OF WAR SCIENCE The Kaiser has approved the foundation of a Trust with the name given above. The aim of the Trust is to further the development of scientific and technical aids to warfare, by uniting the scientific and the military forces of the country for work together. The scientific Work is to be carried on by the following technical committees (or commissions) (1) Committee for the chemical raw materials, for the production of munitions-manufacturing materials. (2) Committee for chemical war materials (powder, explosives, gas, and the like). (3) Committee for physics, including ballistics, telephony, telegraphy, determination of targets and distances, measurements, and the like. (4) Committee for engineering and communication. (5) Committee for aeronautics. (6) Committee for obtaining and preparation of metals.

Jan 8, 1918

By H. Martyn Chance

I HAVE been induced to present this paper to the Institute because I have been unable to find any publication containing a discussion of this subject. In some of our technical schools and colleges the student is required to construct or copy (generally the latter) a number of profile sections as part of his routine work ; but little attention is given to the methods of projecting observed dips and exposures upon the section line, and still less to the method of con¬structing the under (or above) ground curves. As a result of this lack of instruction every engineer or geologist is compelled to invent for himself a system, or copy the style of others. Geological profile sections have frequently been used to determine underground structure from data obtained at the surface, but the experience of engineers in the anthracite coal-fields has shown that they are to be relied upon only in exceptional instances. The possibility of indicating underground curvatures from dip-angles observed at the surface has been found to be limited to a mere approximation of the larger flexures, As a means of predicting the depth and shape of minor rolls, they have been found most unsatisfactory. In the anthracite coal-fields the hypothecatod

Jan 1, 1881

ENGINEERS AVAILABLE. (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Member, graduate of College of Mines of University of California, with 12 years' operating experience in mining and milling in California, Canada, and Mexico, is open for engagement. Speaks Spanish fluently. No. 17. Mining engineer and metallurgist open for engagement Jan. 1 as superintendent of mines or constructing engineer. Technically educated, with 14 years' experience in United States and Latin America in concentration, amalgamation, cyaniding, constructing. At present building large modern .all-sliming cyanide mill in Central America. No. 18. Member, mining and metallurgical engineer, is open to engagement. Specialty, the treatment of copper ores. Nine years' experience in the operation and also in the design and erection of copper smelteries. Four years true pyrite smelting. Able to organize the administration, accounting, etc., of a large plant. Speaks a fair amount of Spanish, Russian, German, and French. Qualified to take charge of a large smeltery, or to act as assistant to manager of a combined mining and smelting concern. No. 19. Member, technical graduate, 33 years old, 11 years' experience as chemist, metallurgist, and superintendent of lixiviation plant and in charge of construction of cyanide mill, is open for engagement. Speaks Spanish. No. 21. Member, lately with the Bishop Creek Milling Co., California, is now open for engagement as mine superintendent or superintendent of construction of mine and mill structures. No. 25.

Jan 12, 1913

By G. T. Hahn

On the basis of the recommendation of Lovell, Vogel, and Wernick,&apos; Fry&apos;s reagent*2 was recently c) if decoration of the dislocations by carbon or nitrogen atoms is a factor in the etch pitting. Experiments were performed with samples of a commercial 1020 steel, a vacuum-melted iron (C - 10 to 15 ppm, 0 - 20 to 50 ppm, N < 2 ppm), both annealed 4 hr at 1100°C, and a zone-refined iron (C - 3 to 5 ppm, 0 - 10 ppm, N < 1 ppm ) in the as-cast condition. Saomple surfaces were prepared by grinding to 600A grit and electropolishing. Initially, effects of etching the steel with modifications of the basic Fry composition were examined. It was found that increasing the alcohol or HC1 concentratior~ retarded dislocation pitting; reducing the acid content promoted secondary pitting. Cooling the reagent and the sample did not improve the quality of the etch pits. Best results were obtained with freshly prepared reagent modified by increasing the CuC12 content to 15 g. This composition was used in subsequent experiments. Annealed samples were etched 10 to 15 sec; cold-worked samples —2 to 5 sec.

Jan 1, 1962

By John K. Hammes, Stanley D. Michaelson

Generally, the mining costs reported for the large open-pit operations in the United States and South America lie within the range of $0.20 to $0.30 per ton of material moved. (These operations have strip- ping ratios ranging from 1.5 to 4.0.) Productivities for the larger North American properties are in excess of 200 tons of material per man shift, while those for the South American operations are less than 200 tons per man shift. The most significant variations in cost are in the categories of haulage and general mine cost. Haulage costs vary, as expected, according to the mine elevation, pit profile, crusher location, and accessibility of a dump area, and general cost variations depend largely on the overhead cost items included in this category. Drilling and Blasting Practice The majority of open-pit copper mine production drilling is performed by rotary drills. Hole diameter varies from 6 in. to 12 in., with 9-in. holes being most common, and penetration rates vary from 35 ft to 60 ft per hour.

Jan 1, 1968

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By S. S. Hartranft

FuRnace-men of the present day agree very nearly as to the best cooling-devices for the protection of blast-furnace hearths and boshes, and the best location of the cooling-system in the brick-work for the maintenance of favorable furnacelines throughout the blast. The replaceable bronze and copper plates are practically faultless; and there seems to be no reason why a furnace-hearth and bosh should not be held in good condition, by intelligent management and the use of replaceable plates, for a period several times the length of the average blast of to-day. While furnace-men have taken these .precautions to protect the hearth and bosh beyond the life of the lining, the portion of the lining above the mantle has been partly protected by some and wholly neglected by others. Some would not construct a furnace without mantle-plates, and others would not construct a furnace with them. In most cases, furnace-men have either trusted to Providence or to the bosh-plates for the continuance of favorable working-conditions above the mantle, and the prolongation of the life of the lining; consequently furnaces are constantly blown out for repairs to the lining, or for relining, when the hearth and bosh are in good enough condition to last through another blast. The following extract from one of Mr. James Gayley&apos;s con-

Jan 1, 1901

By I. Ionel Gardescu

During the latter part of 1930 an agreement was reached among operators in Rumania to curtail the production of oil to about 100,000 bbl. per day. This agreement lasted only a few months and 1931 shows a new peak in production with an average yield of 136,900 bbl. per day as against an average of 116,600 bbl. per day for 1930. The total production for 1931 was 49,210,000 bbl.; an increase of 18.4 per cent over the previous year&apos;s production. It is interesting to compare the percentage production of the major companies to the potential production figures determined by the Government in September, 1930 (Table l), on the basis of which the proposed curtailment was to have been made. The three companies listed first in this table show an increase in average production for 1931 over their estimated potential production rating. This increase might be attributed at least in part to the recent development of the Boldesti field, which is controlled by these companies and of which the production at present is nearly 10 per cent of the total oil output for Rumania. Among the other fields, Moreni still holds first place with an output of 33.6 per cent, followed by Gura-Ocnitzei with 29.3 per cent. In both these fields the main source of oil is from the deeper Meotic sands. Other

Jan 1, 1932