Search Documents

By G. G. Gunther, C. L. Boeke

DISCUSSION I. M. Symonds, (Cia. Minera de Penoles, Monterrey, N. L., Mexico)—Messrs. Boeke and Gunther have written most interesting papers describing their zinc de-leading operations. Mr. Gunther was kind enough to show me his operation last fall. Aside from the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the delead-ing float. The final zinc concentrate still has about 3 pct chalcopyrite, assuming the copper is chalcopyrite, and adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther's remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been confined mostly to the conventional lead-zinc separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In handling relatively high grade ores in the mill we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct zinc content we have had to use 0.8 to 1.2 pounds of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Some time ago we made a laboratory study following Parral and Santa Barbara practice on an ore which had never a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using in the laboratory fresh zinc concentrate from the mill instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the labora-

Jan 1, 1953

By J. J. Lillie

Sublevel stoping was first developed in the Michigan iron mines many years ago. Since that time this method, and modifications with long hole drilling, have been used in a number of non-ferrous mines and have been described in various papers and articles. With a few exceptions, the operations where sublevel methods have been applied are producers of large daily tonnages from ore bodies of considerable size. In selecting mining methods for small properties or relatively small detached ore bodies, sublevel methods often have been overlooked. The method has been used successfully in relatively small operations at Copper Canyon, Nevada, and, more recently, in mining small ore bodies at Darwin, Calif. As a result of this experience, we believe that a review of the general procedure, the advantages noted, and the results obtained will be of interest to many operators of relatively small mines. General Description Briefly, sublevel stoping consists of, first, driving sublevel drifts at predetermined vertical intervals through the length of the stope block; second, breaking an initial mining slot across the stope; third, driving crosscut benches from each sublevel by slabbing into the slot; and, fourth, breaking the ground between benches. Applicability Since this is an open stope method, it requires wall rock that will stand over reasonable stope lengths without caving or excessive slabbing. Ore must be moderately firm but need not be hard. The method is best adapted to steep dipping, tabular or lenticular ore bodies but may be applied to ore bodies of almost any shape if their vertical extent is appreciable. It can be used with dips that are too flat for successful shrinkage stopes and can be modified for use with slushers on dips below about 40". Initial mining at the Copper Canyon operation consisted of sublevel stopes for the wider ore sections and shrinkage stopes for the narrow sections where ore widths averaged about 15 ft. After some experience and a study of comparative results on completed stope blocks, sublevels were substituted for shrinkage stopes even in the narrow ore widths. Practical stope lengths depend upon the character of the walls and the continuity of values within the ore body. Where blocks of low grade or waste are included in the stoping limits, these areas can readily be left as pillars for intermediate wall support and longer stope lengths may be planned. Raises can be spotted in narrow or low grade areas and stope lengths adjusted accordingly. Stoping Details To illustrate stoping details, assume that we have an ore shoot 15 to 30 ft wide and about 200 ft long, with walls that would stand over a stope length of 80 to 90 ft (Fig1). PRELIMINARY DEVELOPMENT Preliminary development for sublevel stoping would be simple. A service raise is driven at about the center of the block and stope limits planned to leave a pillar around this raise. Sublevel drifts driven each way from this central raise will outline the

Jan 1, 1950

ANYONE who wishes to make the patterns for statues in order to cast them later in bronze, even though he himself is the artificer who made them, must take many things into consideration: first, whether they are large or small, and whether they are wholly round or only in part; then of what material they are made, for the way that can be followed if they are of wax cannot be used if they are of clay, wood, marble, or even of plaster; likewise he must consider whether or not it has irons inside to support it. There is also a great difference in facility if the support is placed more in. one way than in another. Great consideration should be given to whether it is to be made hollow or solid. If you have not been the workman yourself, you must at least have been an active helper in this and in every other part in order to be able to observe everything without a fault. For if they are large it is necessary to make their moulds in pieces, with marks and measurements so that you can replace them-at will exactly in the same order and in the same places after they have been taken out. But if you are the artificer [as well as sculptor] the process is made easier. Taking the ordinary way and, over an iron, make out of well beaten moulding clay, compounded with cloth clippings a core exactly as the statue is to be or however large you wish the hollow to be. Dry and bake it. On top of this work the wax, thickening it all over as much as you wish the bronze to be and finish it completely, remembering to arrange that the base may come out solid with bronze so as to support the whole work. Then take some rods of hammered bronze one dito thick and one palmo long. Pass these throughs the thickness of the wax and fasten them in several places in the core of clay that you made. [81] Do it so that they, project out of the wax a good three or four dita. These are, put in so that when the wax is removed the core is held in the middle of the mould that forms the outer part, and this outer part is held by the inner part, namely the core, so that the mould may not move in any part from its place even when it is handled. This done, take some of that clay made with well-prepared cloth clippings as I taught you, and mix with it if you wish some wash ashes or

Jan 1, 1942

Edgar Archibald Collins was born at Truro, Cornwall, Nov. 16; 1877. He was the fifth (and youngest) son of J. H. Collins, a well known Cornish geologist and engineer, who died in 1916. Edgar Collins spent part of his childhood at Rio Tinto, in Spain, and after returning to England was educated at Alleyne's School at Dulwich, near London. His technical training was acquired by practical experience in Cornwall, supplemented by private study and by his father's teaching. This method of training for the work of a mining engineer was preferred by his father to that of the technical schools then available, and judging by its result, was not unsuccessful. It is,-however, noteworthy that all members of the Collins family who were products of this system later sent, or planned to send, their own sons to technical schools. Edgar Collins came to Gilpin County, Colorado, in 1894, and returned there in 1898, after several intermediate years spent in Cornwall. In Colorado he worked, under his brother Arthur, in the California and other mines of the Gilpin County district, and thereby gained a practical skill and experience as a working miner, and a habit of minute observation of vein phenomena, which proved of the greatest value in later years. In 1899 he went to the Smuggler-Union it Telluride, as general assistant to his brother Arthur, and stood the brunt of 3 years of struggle with the Western Federation, gaining a reputation, for quiet courage and sound work under the most difficult conditions. After Arthur Collins' assassination in the Smuggler-Union office, in November, 1902, Edgar left Telluride, and shortly thereafter entered the employment of a syndicate headed by Arthur Winslow, of Boston, to search for and develop new mines. While so engaged he spent several unsuccessful months near Parral, in Mexico, and later visited and sampled the- newly discovered district of Grandpa, afterward known as Goldfield, in Nevada. This led to the acquisition by the Winslow syndicate of the Combination mine, at first under lease and option; and Edgar Collins was placed in charge. The Combination was really the starting point of Goldfield. It was a profitable mine before the discoveries at the Jumbo were made; and while the Combination, being a "Company-account" mine, controlled by a few responsible men, never attracted the publicity that centered around the sensationally profitable leases on the Jumbo and Mohawk, which publicity was used to further the feverish stock-dealings that characterized the new district. The Combination was really the pioneer mine, made the first shipments of rich ore, constructed the first water-line, and built the first mill (designed by F. L. Bosqui, an old friend and associate); and while it pursued a quiet and unobtrusive. career up to the time of its sale to and incorporation with the Goldfield Consolidated, was probably, in ;proportion to the amount of money risked, the most profitable bonanza in the recent history of gold mining.

Jan 11, 1918

By J. C. Uy, A. A. Burr

IN the primary solid solutions of zirconium-base alloys, there is a striking regularity of the effect of solute valence on the stabilization of the allotropic phases.1 The valences derived by pauling2 are for elements as they are bonded in the solid metallic state. Effects of variations in isotopes, alloying elements, and allotropes on their valences are difficult to determine and such data are presently unavailable. Pauling's values are somewhat empirical and approximate, but if some definite correlations can be found between those values and experimental observations, this will lend support to the tacit assumption that the possible variations in valence mentioned above are small. Pauling has amassed a large amount of evidence of such correlations. It is the purpose of this technical note to show another application of the Pauling valences and to offer a possible explanation for this observation. The relationship between the Pauling metallic valence of the solute and the stabilization of allotropic phases in zirconium is shown in Table I, which has been compiled from available data in the literature3 plus the results of work done at Rens-selaer Polvtechnic Institute.' The chemical valences are included for comparison. It can be seen that a solute whose metallic valence is lower than that of the solvent tends to stabilize the a phase while one whose metallic valence is higher than that of the solvent tends to stabilize the 0 phase. It should be noted that, inasmuch as the Pauling valences are periodic with atomic number, this is tantamount to saying that the elements in groups I-A, 11-A, III-A, III-B, IV-B, V-B, and VI-B are a stabilizers while those in groups IV-A, V-A, VI-A, VII-A, VIII-A, I-B, and 11-B are ß stabilizers. The chemical valences do not show such consistency. Although the zirconium-rich end of the Zr-Au diagram is not available, it call be expected that gold, having a metallic valence of 5.56, would stabilize the ß phase. At absolute zero, the Fermi energy level is the criterion of equilibrium, i.e., the structure having the lower Fermi level will be more stable. Conse- quently, allotropic transformation occurs in a metal when thermal excitation raises the Fermi level to a point at which the atoms can be better accomodated by a different structure which yields a lower Fermi level.4-6 Thus in allotropic transformation, a change in structure occurs as a result of the change in the energies of the bonding electrons. Since the Pauling valence is the number of bonding electrons per atom, and these are the only electrons whose energies are affected by thermal excitation,* it can be inferred that the introduction of a solute which has a higher Pauling valence than that of the solvent raises the initial Fermi level; consequently, the transformation temperature is lowered. The converse is also true. The fact that at the transformation temperatures this statement is still fairly valid implies that the contribution due to the difference in specific heat terms of the two allotropes is comparatively small.

Jan 1, 1962

By Charles Trotter

AN instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. DESCRIPTION The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time lapse obtainable with the instrument designed for use in EX or AX size holes is 1 hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. OPERATION Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1947

By Walter Miller

Hundred-octane aviation gasoiine, toluene for T.N.T. production, high-quality lubricating oils for the needs of aviation and the armed forces, and synthetic chemicals for rubber manufacture again commanded the top priorities of the petroleum refining industry in 1944, the third year of America's active participation in the war. The objective continued to be to produce more and more of these materials—to keep up with increasingly greater requirements. By the end of the year all of the new installations projected before 1944, with the exception of possibly two or three that will tail over into January or February of 1945, had been completed and put into operation. And with the completion and putting into operation of these various units and the consequent lessening of construction responsibilities and problems, the industry was put into position to concentrate on the new operations and devote much more of its time and effort looking toward maximum output, both as to quantity and quality from the new facilities. Aviation Gasoline Making high-octane aviation gasoline continued to be the prime requisite of refining activities during 1944 as it was in the two previous war years, with the sights at the end of the year set to still higher figures than those which had been previously projected. About July I the daily output had been raised to 400,000 bbl., with some few large plant installations still to be completed and put into operation. Indications were that by December production would be up to all requirements, with good inventories. However, although by the end of the year the industry was turning out something over 500,000 bbl. a day, the estimated requirements of the armed services had been raised by a considerable figure, owing to the greatly increased aerial activities both in the European and Far Eastern combat areas. By the end of the year, therefore, the picture had changed, with the prospect for a much longer continuation of the European war, so that even with the completion and putting into operation in the United States by January 1945 of the last two or three 100-octane units authorized prior to 1944, it was evident it would be necessary to make still greater efforts to increase output of existing facilities to keep safely ahead of the game. Efforts of the industry and the Petroleum Administration for War as well as the Technical Advisory Committee and other research and development groups are concentrated therefore on methods and means of further augmenting the produc. tion of all existing refinery facilities engaged in making 100-octane aviation gasoline and components entering into it. The goal will be reached.

Jan 1, 1945

By G. G. Gunther, C. L. Boeke

DISCUSSION I. M. Symonds, (Cia. Minera de Penoles, Monterrey, N. L., Mexico)—Messrs. Boeke and Gunther have written most interesting papers describing their zinc de-leading operations. Mr. Gunther was kind enough to show me his operation last fall. Aside from the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the delead-ing float. The final zinc concentrate still has about 3 pct chalcopyrite, assuming the copper is chalcopyrite, and adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther's remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been confined mostly to the conventional lead-zinc separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In handling relatively high grade ores in the mill we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct zinc content we have had to use 0.8 to 1.2 pounds of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Some time ago we made a laboratory study following Parral and Santa Barbara practice on an ore which had never a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using in the laboratory fresh zinc concentrate from the mill instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the labora-

Jan 1, 1953

By Stuart E. Buckley, C. R. Hocott

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By E. H. Edwards, J. Washburn

Zinc crystals were deformed in simple shear and it was found that anisotropic strain hardening occurred in which the inactive slip systems were hardened more than the active system. The formation of dislocation barriers by dislocation interaction was discussed as a possible explanation of the hardening of the latent systems. STRAIN hardening which accompanies slip in a metal crystal is not limited to the slip systems actively contributing to the plastic strain. There is also a strengthening of the latent slip systems which are crystallographically equivalent to the active system. In the case of aluminum deformed in tension, Taylor and Elam1 found that plastic flow on one set of octahedral planes caused either the same or a slightly greater hardening on an inactive set. Similar results have been obtained for crystals of a brass2 and of Cu-A1 solid solutions.3 Experiments by Rohm and Kochendorfer4 indicated that the hardening of the active system exceeded the hardening of any latent system for aluminum crystals deformed in shear. On the other hand, strain hardening in zinc and cadmium crystals tested in simple shear at —196°C was recently found to be greater in the latent than in the active slip direction." When the strain direction was shifted during testing to a direction 60" from the original, a higher stress was required for glide to continue than would have been needed for flow to proceed in the original direction. The relation between the hardening of active and latent systems must be complex, depending upon the relative orientations of the systems and upon the experimental techniques used to deform the crystal. A detailed knowledge of the hardening produced in latent systems would be valuable in choosing between possible dislocation models of the strain-hardening process. The experimental data now available are incomplete and even contradictory. The present study was undertaken to provide quantitative information regarding the relative amount of hardening of active and latent systems for a particularly simple case. Zinc crystals were deformed in simple shear along one of the three crystallographically equivalent directions [250], [1210], and [1120] in the slip plane, and the relative hardening produced in each of these directions was compared. Experimental Procedure and Results The single crystals of 99.99 pct purity zinc used in this investigation were grown from the melt in the form of 1 in. diam spheres. Shear specimens were acid-machined from the crystals by a method which has been described previously. The gage section of the test specimen was a cylinder having a height of 1/8 in. and a cross-sectional area of approximately 1/3 sq in. All specimens were machined with the axis of this cylindrical gage section aligned with the [0001] axis of the crystal. An innovation in the design of the shearing apparatus for these tests was the provision for a rapid shift in the direction of the applied stress from one slip direction to any other slip direction lying in the same slip plane. Fig. 1 shows a section through the specimen and shearing apparatus, and Fig. 2 is a

Jan 1, 1955

By G. H. Kennedy, H. E. Criner

CYCLONE thickeners are "hydraulic centrifuges" designed either to produce a maximum practical separation between the water and solids of a feed slurry or to classify the slurry solids according to particle settling rate. The possibilities of utilizing the thickener to "close" plant water circuits have been investigated. Since the thickener becomes an integral part of the plant water circuit when installed, the basic means by which the solids content of all circulating water systems must be controlled is reviewed. All coal not separated from the circulating water by means of dewatering screens or settling devices must be bled from the plant at the same rate as they are being fed or created by degradation. If this were not true, the circulated volume would finally be completely filled with solids. If the rate of bleed is low, the solids concentration in the bleed and circulating water generally will be high. To keep a reasonable circulating water concentration, large amounts of fresh water must be supplied and the bleed rate must be high. These conditions are usually undesirable because of the difficulty in securing fresh water, the loss of large quantities of coal, and the pollution of nearby streams. Thickeners are the primary stage in the separation of the water contained in the bleed from the coal. Since a thickener, when operating with reasonable efficiency, usually cannot be expected to deliver an underflow containing less than 50 pct water, secondary dewatering devices such as a slurry screen or vacuum filter must be used to separate additional water from the bleed. The surface area required by the filter or screen will be nearly proportional to the total water which must be handled, and therefore the thickener becomes necessary to hold down the original cost. The water separated from the coal is then returned to the plant circuit to maintain the water balance and thus becomes the source of fresh water. It is not necessary to return clear water to the plant to maintain control of the circulating water concentration. It is only necessary that the bleed dewatering devices remove coal in all sizes at a rate equal to that at which these sizes are entering the circulating water. However, practically speaking, in order to maintain low solids concentration, it is usually necessary that the thickener have good recovery characteristics on bituminous coals in those sizes down to 400-mesh. The thickener can remove the smaller sizes from the closed-circuit system at the "solids in" rate and prevent their "build up" in the circulating water as shown in Fig. 1. With the portion of the feed water going directly to the underflow, comes the very fine solids not concentrated by the cyclone. All the larger solids are removed from the feed and delivered in a concentrated condition at the underflow. To apply thickeners with some reasonable assurance that operating requirements will be met, it is necessary to know the rate at which solids of all sizes must be removed from the circulating water and to know the thickener characteristics. The required removal rate of fine solids not recovered by other dewatering devices may be estimated from the size distribution and tonnage of the plant feed with a reasonable allowance for degradation in the circulating water system. A more reliable estimate may be secured by sampling the plant bleed water during a constant load period.

Jan 1, 1952

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By N. L. Muench, J. S. Osba

Research conducted previously has demonstrated that spectral analysis of gamma radiation from the naturally radioactive elements present in earth materials permits detervination of the relative concentrations of these elements. This research suggested that spectral analysis of gamma radiation resulting from neutron bombardment of elements not nor-mally radioactive might serve to identify these non-radioactive elements, and might permit their quantitative determination. To investigate this possibility, laboratory experiments were conducted in which various earth materials were subjected to bombardment by neutrons from a polonium-beryllium source, and in which the spectra of the resultant gamma radiation were analyzed. The geometry of the lab-ortory system was designed to simulate wellbore conditions. The laboratory work demonstrated that some elements not only can be identified with relative ease, but also can be determined quantitatively. This finding indicates that the use of an intense source of more energetic neutrons may lead to the identification and measurement of additional elements of interest by means of induced nuclear reactions. INTRODUCTION In recent years the applications of nuclear physics to the producing branch of the petroleum industry have become increasingly numerous. One significant development, an outgrowth of nuclear science which is of potential importance in well logging, has been the analysis of gamma-ray spectra of naturally radioactive elements in earth strata. The work of Brannon and Osoba1 has demonstrated that presently available equipment and techniques may be used to determine the relative concentration of thorium, potassium, and uranium in underground strata by means of gamma-ray spectral analysis. Success of the research on spectral analysis of naturally radioactive elements suggested that spectral analysis of induced radioactivity might serve to identify, and perhaps measure quantitatively, those elements which normally are not radioactive, but which become radioactive on neutron bombardment. It was to investigate this possibility that the research described in the following sections was undertaken. THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bom- barded with neutrons, emits gamma rays of energies characteristic of that element. Therefore, in theory, an element may be identified by analysis of the energy spectrum of the neutron-induced gamma radiation. If a neutron impinges upon the nucleus of an atom, any one of several reactions may occur. For identification of elements in earth formations the more important are listed below: 1. The neutron may be elastically scattered, as in a collision between two billiard balls. In this case the total kinetic energy is conserved, and no nuclear radiation is emitted. 2. The neutron may be inelast-ically scattered, as in a collision between two automobiles in which case the total kinetic energy is not conserved. The lost kinetic energy reappears in the form of gamma radiation. 3. The neutron may be captured, in which case the neutron becomes a part of the target nucleus, and a gamma ray is emitted. For example, if the target nucleus is H1, the pro-duced nucleus will be H3, and gamma radiation of a particular energy will be emitted. 4. The neutron may produce nuclear fission, or may enter into miscellaneous reactions which result in the emission of

Jan 1, 1958

Discussion of the paper of HOWARD N. EAVENSON, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October,' 1914, pp. 2637 to 2660. GEORGE S. RICE, Pittsburgh, Pa.-I think it is very wise to point out the greater liability to explosions in certain parts of the year, if there be such difference, with the caution, however, that vigilance be not relaxed at other times. In comparing the figures for the United States with those of Europe, I think we should separate them as far as possible according to cause of origin and means of propagation. That is to say, it would appear to me that the majority of our explosions are due more directly to the ignition of coal dust directly from the flame of explosives, whereas, judging from my inquiries and observations in some of the mines of Europe, the majority of their explosions have been caused by the ignition of fire damp. Now, in the case of fire damp, I do not think that anybody has yet attempted or has been able to find any connection between the seasons and the issuance of methane into mines. One thing must be borne in mind, that if you get a strong explosion of fire damp, dust of a character that might not ignite readily by itself might assist in the extension of an explosion of fire damp through a considerable area in the mine, if not throughout the mine. While it is true we have many lesser explosions in this country attributable to fire damp, it would appear that the majority of all the mine explosions of the country, in considering the means of propagation beyond the locality of the origin, are due to coal dust; and it is the liability to coal-dust explosions that appears to be affected by seasonal changes. Hence the desirability of separating statistically (if it could be done by the inspectors) fire-damp explosions from coal-dust explosions, in order to obtain the true value of the seasonal effect. Nevertheless, in spite of the inclusion of fire-damp explosions with coal-dust explosions, the preponderance of the evidence, as indicated in Mr. Eavenson's figures for American mines, has shown that' in this country there were more explosions in the winter and spring months, when the mines are drier; that is, when the mines are apt to be drier. Whereas, according to the European figures that he has gathered, it seems to be very clearly demonstrated that in France, England, and Belgium, the time when explosions occur has no connection with any particular season. That, I think, is partly due to the point just mentioned, that a majority of their explosions have originated from fire damp. The European mining men have been more careful, generally speaking, with the use of explosives than we have, so that the cause of ignition from that source has been less. Only comparatively few of the mines in foreign

Jan 4, 1915

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By Heribert Wiedemeier, Ali Khan

The tetnperature-conposition phase diagram of the syste,n MnS-CdS has been investigated over a range fro)n 600° to 1000° C. The small degree of solid solution on the MnS rich slde cornpared to the large CdS rich single-plzase region could be esplained by the difference in strzrctures of the cotnponents and the relative sizes of the metal ions. The change in lattice parameter as a function of cot)zposition is linear atzd jollous Vegavd's rule within experittzental limits of error. Mns and CdS have gained considerable attention in recent years because of their interesting solid state properties. In order to investigate such properties and thermodynamic quantities of mixed compositions of transition metal chalcogenides, it is necessary to establish their phase diagrams. Two earlier publications are concerned with the MnS-CdS system. Schnaase' found complete miscibility when MnS and CdS were co-precipitated in aqueous solutions at room temperature. However, there is evidence that the mixed crystals were not stable over the entire range of composition. roger's' investigation of the ternary system ZnS-CdS-MnS at 900" C indicates a solution of 48 mole pct MnS in CdS. During the course of this work which covers a temperature range from 600" to 100O° C, emphasis has been placed on the use of high-purity materials and well-defined modifications of starting products. EXPERIMENTAL Starting Materials. The stable green modification of MnS with NaCl structure was prepared by direct fusion of the elements and by chemical transport reaction. Stoichiometric amounts of manganese of 99.99+ pct purity and of sulfur of 99.999 pct purity from Gallard-Schlesinger Corp. were sealed in an evacuated quartz tube at a pressure of 10"5 mm Hg and annealed for 48 to 60 hr at 800°C. The quartz tubes used throughout this work were outgassed under high vacuum at a temperature of 90OU to 1000° C for 12 to 18 hr. For the synthesis of MnS by chemical transport3 stoichiometric ratios of elemental manganese and sulfur and small amounts of iodine were sealed under vacuum in a quartz tube, which was placed in the temperature gradient, 900/800-C, of a two zone furnace. Single crystals of MnS in form of platelets and octahedra were deposited at the cooler end of the tube. The manganese content was determined by EDTA titratin. A typical result of several analyses was 63.05 pct Mn which agreed well with the computed value, 63.14 pct. Commercially available CdS of 99.9+ pct purity, a mixture of the cubic and hexagonal forms, was converted into the hexagonal high-temperature modification by annealing CdS under vacuum in quartz tubes at 700° C for about 36 hr. As a second method, cadmium sulfide was transported in a temperature gradient, 70O° /650" C, with in vacuo sublimed iodine from the hot to the cooler zone of the tube. Large sized crystals in form of hexagonal columns and some platelets were obtained. An average result of the cadmium analysis by EDTA titration4 was 77.93 pct in good agreement with the computed value, 77.81 pct. Only the NaCl modification of MnS and the wurtzite modification of CdS were used for the solid solutions. Preparation of Solid Solutions. Finely powdered MnS and CdS samples were thoroughly mixed in molar ratios and compressed into pellets of about 6 mm diam and 2 mm in height at a pressure of approximately 13,500 atm.

Jan 1, 1969

By T. L. Joseph

S. T. Killian (Johnstown, Pa.)—This is one of the finest papers I have read. Tying in stoichiometric calculations with furnace performance and practice is a step which had to be taken sooner or later. The noteworthy difference between Dr. Joseph's type of calculations and regular blast furnace calculations is that the Ib mol system is used as a basis. With the Ib mol system, weights, volumes, and chemical reactions can all be expressed in the same equation. In the paper, wind, ore, flux, and fuel are all expressed as lb or lb mols. Probably Dr. Joseph does not realize it, but the vague word coke appears only twice in the entire paper. Lb of C and Ib mols of C are followed through reactions but the word coke appears only as 1560 lb coke per ton of pig and 1700 lb of coke per ton of iron. Obviously in order to understand furnace reactions, the coke should be expressed as lb or lb mols of C. Furnaces can also be compared more easily. In some respects the paper is too thorough and too complete. The effects of the metalloids reduced into the iron upon the top gases represents a difference of less than 3 pct of the CO formed in the bosh. Due to the completeness of the calculations in relation to the CO/CO2 ratio, this was included and was necessary. However, the exclusion might have enabled more furnace men to follow the lb mol system of calculations through the blast furnace to a better degree. By considering only irons of similar analysis, this part of the calculations might have been omitted. However, if this had been done, total rewriting of the paper later would have been necessary in order to make the work complete as it is now. It also would not have been nearly as authoritative. In the paper, there appears the reaction: H2O + CO ? CO2 + H2 [I] Dr. Joseph states that he did not take this reaction into consideration in any calculations pertaining directly to the paper. The piobable reason- for this is that although it contains all the main reacting top gases except N2, it is rather inflexible since it is monomolecular in relation to each of the reacting gases and does not tie in with the gasification of C. Actually the reactions: H2O + C ? CO + H2 [2] 2H2O + C ? CO2 + H2 [31 and the solution loss reaction: CO2 + c ? 2c0 [41 tend to assume an equilibrium through the reaction: H2O + CO ? CO2 + H2 [I] which should be considered a balancing or equilibrium reaction. Reactions 2, 3 and 4 permit furnace conditions to balance with the CO/CO2 ratio and H2 formation. They tie in with the solution loss. Reaction 1 unites them chemically. Probably the best calculation to make at this time would be to try to find the relative importance of the CO2 from the flux and the H2 in the dilution on an actual furnace gas analysis. For this purpose the Dob-scha-Carnegie-Illinois paper—"Effect of Sized and Sintered Mesabi Iron Ores On Blast Furnace Performance" is chosen. This paper was presented before the blast furnace section of the AIME in 1948. This represents the best large scale furnace operation available to me. Unfortunately the changes were brought about by beneficiation of the burden and not by changes on one burden. In choosing the basis for the calculation in relation to the furnace, 100 mols of dry top sgas is chosen. This leaves something to be desired inasmuch as the nitrogen basis is changing but I believe it will be better understood than any other type and it is the easiest to use.

Jan 1, 1952

By B. Trafton, H. L. Hartman

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. The revised program-written in FORTRAN for the IBM 7074 computer in Penn State's Computation Center-is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following: 1) Distributes an assumed total quantity of air flow among all airways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2) Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3) Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values. The basis of analysis used is the Hardy Cross method of successive approximation for solution of any fluid network, explained in detail in the earlier article. In brief, corrections to assumed air flows are computed for all the loops of a network; following distribution to the airways of each loop, the process is repeated until acceptable accuracy is attained. When a hand or desk-calculator solution is used, there is advantage to close approximation of the actual flows in the original assumption of air-flow distribution in the network. Since publication of the previous paper, in which assumption of initial quantities was also necessary in the computer solution, the program has been modified to make the first distribution itself, assigning the total quantity to one specified path in a split and then proceeding to correct the flows. The number of iterations required for a high-accuracy solution is little affected, at least in networks of few loops, 10 to 15 being sufficient to reduce the error to 1 pct or less. The principal limitation of the original program was that it contained no provision for handling a fan. Further, it did not determine the overall head loss in the network and was not designed for multiple parallel openings, such as occur in coal mines. The revised program was written to overcome these disadvantages and also to print out the adjusted flows for all airways, corrected for the system operating point. At the present time, the program can handle only an external fan. The procedure employed in solving a ventilation network is now as follows: 1) Input data consisting of airway characteristics and loop designation along with assumed direction of flow, for each branch of the network and any trunk airways, are fed into the computer. 2) Employing the resistance relationship, where R is resistance, K is friction factor, P is perimeter, L is length, A is area, and n is number of airways (where multiple intakes and returns are employed); values are computed for all airways. 3) An arbitrary, continuous route of flow through the circuit—from beginning to end—is selected and the path identified by airway numbers and read in. 4) Based on a total assumed quantity of flow Q (usually 100,000 cfm.) the computer employs the procedure described in the previous article in distributing quantities of flow among all the airways until a satisfactory level of accuracy has been attained (in the current program, the machine is turned off when the cumulative corrective error in cfm, is reduced to five times the number of airways). 5) Airway head losses H are calculated by the relation H = R Q2 and cumulated along the original designated flow route to find the overall head loss for the network. Trunk airways are then included to obtain the mine head.

Jan 1, 1964

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By L. S. Kolbert, C. H. Baab

Introduction In June 1981, the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the US coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent." With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. Major Features and Benefits of Nuclear Measurement and Analysis Systems There are many features and benefits of nuclear instrumentation. The major benefit is that nuclear instrumentation is non-contacting. The measuring heads do not contact the process materials. This enables measurements of corrosive, abrasive, or high temperature materials with no loss of performance, reliability, or useful life. Also, there are no moving parts to wear or be fouled by dust or corrosion. Installation is simple and inexpensive. For instance, density gauges are simply clamped onto existing pipe runs. Weigh scales and level switches usually require nothing more than welding brackets to customers' equipment. Once installed, routine maintenance can be performed without interrupting the process. Thus, nuclear instrumentation is highly reliable and easily installed and maintained. The operating life of the instrumentation is virtually unlimited. Principle of Operation Nuclear belt weigh scales, point level switches and density gauges all operate on the gamma-ray transmission principle. A beam of gamma radiation from a radioisotopic source is projected through the process material either on a belt, in a vessel, or in a pipe. Opposite the source is a radiation detector whose electrical output is proportional to the intensity of the radiation it absorbs. Gamma radiation is part of the same electromagnetic spectrum that encompasses light, infrared, and x-rays. In many respects, gamma radiation behaves much like light. However, it is far more penetrating and can be transmitted through considerable thickness of materials that are opaque to visible light, e.g., several inches of steel. Types of Nuclear Instrumentation in Coal Preparation Plants There are four types of nuclear instrumentation presently being employed in coal preparation plants. They are: •Belt Weigh Scales •Point Level Switches •Density Gauges •Coal Analysis Equipment. Each type of instrumentation has a number of potential applications within the plant. What follows is a discussion of three different types of devices and their applications. Weigh Scales In coal preparation plants, weighing instruments are used for measuring material throughput, totalized weight, and batch weight on conveyor belts and other transport equipment. They are also used on drag chain conveyors, vibrating conveyors, and screw conveyors. Weighing is important for receiving the run-of-mine coal, controlling mass flow, scheduling production, and loading and shipping the washed coal to market. There are two basic types of weighing instruments: gravimetric and nongravimetric devices. Gravimetric devices are units which measure the pull of gravity on the material being weighed. Nongravimetric devices are not dependent on the force of gravity on the sample. Nuclear weigh scales are the most prevalent nongravimetric devices used. The nuclear weigh scale works on the same basic principle as other nuclear gauges. The greater the quantity of material placed in the path of a radiation beam, the more radiation will be absorbed by the material. In weigh scales, Cesium 137 source is generally placed above the moving stream of material so that the radiation is directed through the material. An ion chamber radiation detector is on the opposite side of the material. The radiation passing to the detector generates a signal which is inversely proportional to the weight of the material present. This signal is amplified and integrated with the speed of the process flow yielding the weight. The weight is indicated and can be totalized for throughput, batch control, etc. In conclusion, radiation weighing methods have become well established in the coal preparation industry throughout the world. As mentioned before, this device finds its most

Jan 1, 1985