Search Documents

By R. L. Perrine

This paper shows how stability theory can be used to optimize solvent recovery of oil. Application of the theory leads to definition of the limiting conditions required for stable displacement to occur. One of these conditions is that the size of a solvent "slug" must at least equal a prescribed minimum. The criteria to be satisfied are miscibil-ity and stability. Stability implies that no viscous fingering will occur and that mixing will be caused only by a dispersion process. Miscibility implies that complete recovery will be obtained from the swept regions. Thus, for any specified set of reservoir conditions, an optimum use of solvent is defined. INTRODUCTION The early outlook for solvent flooding as a means to increase oil recovery was very favorable. Some laboratory results indicated that a "slug" containing perhaps 2 to 3 per cent of a hydrocarbon pore volume could be successful. However, other data suggested as much as 30 per cent would be required. The difference is of considerable economic importance. A theoretical explanation for these divergent results has been advanced by the author.1,2 Stability theory defines conditions for two distinct flow regimes. In stable displacement, solvent and oil become mixed by a dispersion process, and the solvent requirement is small. On the other hand, unstable displacement can degenerate into viscous fingering. The practical result is a considerable increase in the extent of mixing and, thus, in the solvent required. The present paper shows how to use stability theory to optimize solvent recovery of oil. Oil is usually considered to be displaced by a small amount, or a slug, of solvent. Gas in turn follows solvent. Any fingering will permit contact of nearly solvent-free gas and oil, leading to immiscibility and reduced recovery. Thus, our optimum is defined by two restrictions — stable flow and miscibility. Although an immiscible solvent process could prove more profitable than any miscible process, such processes lie outside the selected definition of an optimum. The usefulness of computations based on the present work will depend on the validity of the general theory. Because the important idealizations required tend to minimize the predicted solvent requirement, the results should state correctly the limiting conditions required. Therefore, theoretical calculations should have practical value. This paper first reviews several principles that result from stability theory. The following section describes use of these ideas in relatively simple systems which symmetry makes appear one-dimensional. Of particular importance is the step-by-step design of 3 stable minimum-solvent slug. The use of stability theory in cases of multi-dimensional displacement is discussed and, finally, suggestions are given for simplified practical application of the theoretical results. PRINCIPLES OF STABILITY THEORY The use of perturbation methods to derive stability conditions has been shown by the author.l The discussion is presented in terms of the fractional concentration of solvent in the single hydrocarbon phase. Quite generally, any disturbance can be represented as a Fourier series, of which only the least stable term need be considered. Denoting this term at time t = 0 by cn,

By E. E. Anderson, R. L. Newacheck, J. Kohl

Radioactive materials were used underground before the advent of the nuclear reactor. Radium containing ores have been mixed with cements and other materials for later location in oil wells by gamma ray logging since 1940.1 Perforating bullets have been marked with radium salts,, and radioactive materials have been added to drilling muds to find the cause of "lost circulation."' More recently colloidal suspensions of radioactive cobalt-60 and silver-1103 and solutions of 1-1314 have been used in waterflooding operatiorns to determine injection profiles, flow paths and water velocities. In this paper a recent and interesting underground tracer application is discussed. Development work and field engineering were carried out under the direction of Tracerlab, lnc., with assistance from personnel of the client. A gaseous tracer, argon-41, was used in an attempt to determine the cause of leakage from an underground gas storage reservoir. STATEMENT OF PROBLEM This gaseous tracer application was carried out for the Natural Gas Storage Co. of Illinois. This company has developed an underground gas storage field 1,750 ft below the surface of the earth near the village of Herscher, Ill., about 60 miles south of Chicago. The total volume of gas stored in the field was estimated to be about 13 billion cu ft in the spring of 1954. The field has a maximum estimated storage capacity of 90 billion cu ft. The gas is contained in the Galesville sandstone, previously a water bearing formation of about 25 per cent porosity. The water as it is pushed out by the gas forms a barrier for the gas around the edge of the reservoir. Over the top and beneath the bottom of the reservoir are located several layers of impervious rock, which barring cracks or unplugged and unknown wells should act as seals. Twenty-one injection and withdrawal wells were drilled into the Herscher reservoir and gas injection was begun during the summer of 1953. After a few weeks of gas injection, evidence of gas leakage was detected at the surface; water wells began bubbling and losing prime, and dry spots in the fields indicated gas leakage from uncharted oil wells. In every case, the leakage could not be traced back any further than the water bearing formations a few hundred feet below the surface. An extensive search was made to locate uncharted oil wells which were believed to be possible channels for the gas from the storage formation to the water containing formation. Long-time residents in the area assisted in the location of several abandoned oil wells. The wells when located were cleaned out and either used as vent wells to relieve the gas pressure in the water formations, or were plugged with cement. None of the wells even approached depths which would endanger the soundness of the storage reservoir. All of the injection wells were tested for leaks in the casings by conducting neutron surveys and by other techniques. To detect any leakage up through the cement-filled annulus surrounding the casing, a section of the casing wall in one well was milled out. Then, plugs were installed above and below the cut-out section and pressure applied to the annulus, which proved conclusively that the cement was sound in that well. The well was then plugged with cement and abandoned. In another well, ammonia was injected into the well and a temperature log was made. It was hoped that a leak would be re-

Jan 1, 1956

By Parke A. Dickey, Robert B. Bossler

The presence of connate water in oil sands is of far greater practical significance in secondary oil-recovery operations than it is in primary operations. The percentage saturations of oil, water, and gas in a depleted field determine whether it will be economically possible to recover oil by secondary methods, and whether water-flooding or gas-driving, or either, will be successful. It is suggested that economic recovery of oil by secondary water-flooding can occur only when a rich bank of oil is formed by the encroachingm water. If the sand has a greater effective permeability to water than it has to oil before flooding, a bank will not be formed, and water-flooding will not be successful, although gas-driving may be. Published results of laboratory work indicate that the effective permeability of a sand to oil and water depends primarily on the saturation of the sand by these phases. They also indicate that a small difference in relative saturation produces a large difference in effective permeability to the phase in question. There thus exists a critical range of saturations, wherein a small change in oil and water content of the sands will make water-flooding possible or impossible. In gas-drive operations the water saturation is less critical but no less important. The presence of connate water in a sand increases the proportion of the residual oil that may be recovered by gas drive. Sands containing oil saturations too low and water saturations too high to make water-flooding possible can often be subjected to gas drive with economic recovery of oil. The results of laboratory work on test samples that do not contain water cannot be applied to normal field operations. More tests on cores containing water as well as oil are desirable, and the improvement of coring technique is necessary. However, sufficient data are already available to enable an operator to use core data intelligently in estimating the chances of a secondary oil-recovery program. Introduction In recent years laboratory work has led to a much better understanding of the principles of oil-reservoir performance. The general principles of the expulsion of oil from sandstone by gas or water were developed by geologists of the Second Geological Survey of Pennsylvania in the 1870lsl but only recently has the mechanism of gas or water drive been intensively investigated. Most published articles have large the facts established in the labora tory to the primary production of oil from flush fields- This Paper is not based on any new observations, but is an attempt to apply some of the conclusions obtained in the laboratory and described in the literature to the recovery of oil from depleted pools by secondary methods. One of the most important factors that determine whether or not a secondary-recovery operation is economically successful is the ratio of injected fluid to oil recovered. This ratio may be expressed as the over-all or cumulative gas-oil ratio if gas is the driving medium, or water-oil ratio if water is the driving medium. Recent theoretical and experimental work has shown that the relative amounts of

Jan 1, 1944

By M. A. Selim, W. H. Somerton

Thermal expansions and heats of reaction of three typical sandstones were measured in the temperature range of 25°to 1,000°C. The significance of these data in subsurface heat-transfer calculations is discussed. Linear thermal expansions were measured both parallel and perpendicular to the bedding planes. Volume expansions are reported as the perpendicular expansion plus two times the parallel expansion. Expansion behavior of the sandstones was found to be controlled by the expansion characteristics of the quartz content. Differential expansion of the quartz grains and other minerals included in the sandstones caused permanent deformation of the heated samples after they were cooled to room temperature. Structural damage resulting from heating is probably an important cause of the reduction of thermal conductivity of heated samples. Measurements of heats of reaction were based on the known heat required for a- quartz inversion. Thermal reactions, which probably include deby-droxylation of clay minerals and decomposition of carbonate minerals contained within the samples, were found to require more than one-fourth of the amount of heat necessary to raise the temperature of the rock alone. In shales and limestones, the reaction heat could be substantially greater than that required from specific heat considerations alone. INTRODUCTION In earlier work, l-3 methods of measuring thermal properties were developed and thermal data for several sedimentary-rock types were reported. Data included thermal conductivity, specific heat and thermal diffusivity. In addition, calculations of heat transfer in subsurface formations may require data on the thermal-expansion characteristics of rock and the heats of reaction of mineral constituents. Thermal expansion of rocks is relatively small in magnitucle and, from the standpoint of change in bulk density, has only minor effects on heat-transfer cliaracteristics. Thermal-expansion behavior, however, may have significant effects on the structure of rocks. Differential expansion of different minerals and along different crystal-lographic axes may result in structural damage which could effectively reduce the thermal conductivity of the rock. Many mineral constituents of sedimentary rocks undergo phase or related changes when heated to sufficiently high temperatures. Although some of these reactions (such as the a-ß quartz inversion) are reversible and the heat absorbed is returned to the system upon cooling, many of the major reactions are irreversible. Through certain temperature ranges, the additional heat energy required to complete the reactions may be nearly as great as that necessary to raise the temperature of the rock in the absence of thermal reactions. If the heat requirements for these reactions are not considered, serious errors in heat-transfer calculations may result. Thermal-tzxpansion and thermal-reaction data have been obtained for three typical sandstones. Methods of measurement and results obtained are reported and discussed in the following. THERMAL EXPANSION OF SANDSTONES The linear expansions of three outcrop sandstones (Bandera, Berea and Boise) have been measured in the temptbratue range of 25° to 1,000° C. Expansion measurements were made in the directions parallel and perpendicular to the bedding. The differential expansion apparatus used is that described by Mitoff and Pask.4 The test sample is heated in an electric furnace with a temperature rise of 6°C/minute. The lengthening of the samples upon heating is compared with the small and known expansion of a fused silica rod. The change in length is transmitted to an X-Y recorder by means of a Statham transducer. A maximum error of ± 1.5 per cent has been obtained with this apparatus

By C. Gatlin, C. E. Nemir

A common cure of lost circulation is the introduction of granular bridging agents into the mud system. Many materials, such as ground nut shells, are used for this purpose. If the trouble causing void (fracture, fissure, vug, etc.) is not too large, the granular agent forms a "bridge" across or within the opening. Successively smaller particles in the mud stream then accumulate on and/or within this bridge until normal filtration is finally established. The efficiency of many bridging agents has been studied in the laboratory using various slot testers.',' Many investigators have remarked that a granular bridging material should have the proper particle size distribution. With the exception of the broad range specified in the patent of Goins and Nash,3 here is apparently no definition as to what this distribution should be. A bridge may be initiated when several particles of lost circulation material lodge against each other in a fracture or other void. Smaller particles then may bridge the openings between the larger, previously bridged particles. This process continues until the voids become quite small and the problem becomes one of filtration. It would seem logical that an optimum particle size distribution exists, i.e., one containing the proper quantity of properly sized material to fill the successively smaller voids of the bridge. The filtration characteristics of drilling fluids may be subject to a similar analysis. It has been clearly demonstrated by many workers that the filtration behavior of various muds can be altered by particle size control.'.' Slusser, et al, divided filtration into three periods and showed that particle sizes affecting a given period did not necessarily affect other portions of the filtration curve. An analagous problem is the proper sizing of gravel, liner slots and screen sizes in various sand-exclusion problems. Here the situation is reversed in that a proper "void" size, rather than the size of the bridging agent, is sought. The classic work of Coberly 9 forms the quantitative basis for most sand-exclusion processes. It is interesting to note that, in general, Coberly's work has been overlooked by most drilling-mud researchers. Other investigators have made various studies of the effect of particle size distribution .on drilling-mud properties. As a part of their studies, Fancher and Oliphant reported 30-minute filtration loss of a variety of mixtures of particle sizes.'' Gates and Bowie noted an effect of particle size distribution on filtration, as well as on other physical properties.' MAXIMUM DENSITY THEORY A maximum density mixture has been mentioned as the possible solution for both lost circulation and mud filtration problems. Furnas 12 derived mathematically a method for obtaining maximum density of beds of packed solids, having either a given number of component sizes or a continuous gradation of sizes. This work was verified experimentally by Anderegg.13 or mixtures having a continuous grading of sizes, the interval between sizes is taken as successive screen sizes of interval 2 The ratio of the quantity of each size and the next smaller size is given by the equation Fig. I, number of size intervals of ratio 2 taken from Furnas' paper, gives the value of n + 1 for any given values of + and K, where K is the ratio of the diameter of the smallest particles to the diameter of the largest particles. Measurement by weight assumes, of course, constant density for all particle sizes. Choosing the quantity of the smallest particle size as a unit weight, the required weights of the successively larger interials are then r1 r2 r3 . ®1,2,3. Thus, the grading curve of a maximum density mixture represents a geometric pro gression of ratio r.

By Leendert de Witte

A review is given of the principles on which recently proposed methods of electric log interpretation in shaly sands are based and of the evidence brought up in support of the theoretical derivations. It is. pointed out that the qualitative techniques suggested to date have a tendency to be too pessimistic in the prediction of the presence of commercial hydrocarbon accumulations. In the quantitative treatment, a new concept is introduced, namely that of strongly reduced activity of the double layer counter ions which are present near the negatively charged rock surfaces. This lemmu when applied to the calculation of the equilibrium concentratiotls of interstitial waters yields a set of very simple relations. The resulting expressions for electrochemical potentials across rock samples appear in satisfactory agreement with laboratory experiments. The formulae obtained for the electrical conductivity of shaly formatioris are of the same form as those arrived at empirirally by previous workers. Combination of the expres.riorls for potentia1s and conductivities gives a direct proof of the Tixier relation which states that for shaly water sands the product of apparent formation water resistivity and apparent formation factor equals the resistivity of the sand 100 per cent .saturated with formalion water and which was verified by the work of Wyllie and Perkins and their co-workers. The relations for the resistivities and spontaneous porer11inI.s have been extended to the case of hydrocarbon hearing shaly formations, thus laying a formal basis for the quantitative interpretation of electric logs in shaly oil sands. INTRODUCTION The presence of disseminated clays in porous rocks saturated with electrolytic solutions has a strong influence on the transference of ions taking place under electrical or chemical potential gradients. Both the electrochemical emf's in evidence on the SP curves of electric logs and the electrical conductivity measured on resistivity logs arc directly dependent on the ionic transference in the interstitial waters of the formations traversed by boreholes. A large number of researches have been carried out on the nature and magnitude of the effects of clays on ionic transference. The most recent of these have been described in papers by McCardell and Winsauer,1 2 Wyllie and Southwick,3 poupon, Loy, and Tixier,4 and by Perkins et al.5 Most of these authors consider the effects of the clays as due to the fixed negative charges on the clay lattice. These charges cause the formation of diffuse surface layers with a high concentration of positive ions. The internal solution of the shaly reservoir rock has therefore a different ionic composition and concentration than the electrolyte with which it is in equilibrium (connate water produced from the formation or mud filtrate by which the formation is invaded). To calculate the equilibrium concentration of the internal solution, use is made of the Donnan6 relation, which states that the mean ionic activities of the internal solution and of the external electrolyte must be equal. From this and the

Jan 1, 1956

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By Richard P. Rothwell

At the Boston Meeting of the American Institute of Mining Engineers in February last, Mr. George W. Mansfield read an interesting paper on " The Electric Motor in Mining Operations," and he entered into the calculations of power required and cost of transmitting energy in great or small quantities to a considerable distance. I do not intend to go over this ground, or to enter into any discussion of the technical details of transmitting power by electricity, but merely to set up a milestone on the road of progress to show where we now are, how far we have come, and if possible

Jan 1, 1889

By B. D. Cullity, K. S. Sree Harsha

When a copper or aluminum single crystal is swaged into wire, the resulting deformation texture depends on the original orientation of the crystal. The<100> and <111>orientations me essentially stable, while <110> is unstable. The greater the <100> content of the deformation texture, the stronger the wire is in torsion. the greater the<111>content, the stvonger it is in tenszotz. The preferred orientation (texture) of fcc wires, either after deformation or recrystallization, is usually a double fiber texture in which some grains have <100> parallel to the wire axis and others have <111>. The relative amounts of these two texture components, as reported by different investigators for the same metal, vary considerably. Previous work in this laboratory&apos; has shown that the starting texture of a wire, i.e., the texture which it has before deformation, can have a decided influence on the texture produced by deformation. In particular, it was found that the deformation texture of copper wire is essentially a single <100> texture, if the wire before deformation contains only a <100> component. This is true even when the deformation is carried to more than 98 pct reduction in area. This paper reports on further studies of the role played by the starting texture. Copper and aluminum single crystals of various orientations have been cold swaged into wire, and quantitative measurements of the resulting deformation textures have been made. The tensile and torsional properties of the deformed wires have also been measured, and the relation between these properties has been correlated with the texture of the wire. These measurements were made in order to demonstrate that a cold-worked wire can be made relatively strong in torsion and weak in tension, or vice versa, by proper selection of the texture before deformation. MATERIALS The copper was of the tough-pitch variety, containing, by weight, 99.962 pct Cu, 0.003 pct Fe, 0.025 pct 0, and 0.0021 pct Si. The aluminum contained more than 99.99 pct .&apos;41; the only reported impurities were 0.001 pct Fe, 0.001 pct Si, and 0.003 pct Zn, by weight. Large single crystals of these metals were grown by the Bridgman method in graphite crucibles and a helium atmospliere. Cylindrical specimens of predetermined orientation, about 1.5 in. long and 0.36 in. in diameter, were machined from the as-grown crystals and then etched to 0.25 in. to remove the effects of machining. Their orientations were checked by back-reflection Laue photographs, and they were then swaged to a diameter of 0.050 in. (96 pct reduction in area). 111 order to study the "inside texture" of the deformed wires, they were etched, after swaging, to a diameter of 0.040 in. before the texture measurements were made. TEXTURE MEASUREMENTS The fiber texture which exists in wire or rod can be represented by a curve showing the relation between the pole density I, for some selected crystal-lographic plane, and the angle $ between the pole of that plane and the wire axis (fiber axis). Such a curve will show maxima at particular values of , and these values disclose the texture components which are present. The relative amounts of these components can be determined2&apos;3 from the areas under the maxima on a curve of I sin F vs F. It is seldom necesszlry to measure I over the whole range of F from 0 to 90 deg, since the existence of maxima in the low-F relgion can be inferred from measurements confined to the high-F region. The X-ray measurements were made with a General Electric XRD-5 diffractometer and filtered copper radiation, according to one or the other of the following procedures: 1) A method developed in this laboratory,4 involving diffraction from a single piece of wire. 2) A modification of the Field and Merchant method.5 This method was originally devised for the examination of sheet specimens, but it can easily be adapted to the measurement of fiber texture. Three or four short lengths of wire are held in grooves machined in the flat face of a special lucite specimen holder. The axes of the wires are parallel to the plane defined by the incident and diffracted X-ray beams, and the holder to which the wires are attached can be rotated step-wise about the diffractometer axis for measurements at various angles 9.

Jan 1, 1962

By John A. Church

AT a time when the treatment of gold and silver ores by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

Jan 1, 1873

By William J. Potter, Roger N. Pyle

Introduction The primary ingredient for survival of mining companies during a recessionary period is to be innovative and resourceful in the structuring and financing of operations. Over the past decade, many mining companies have had to retrench and restructure their operations and to redeploy their assets just to survive. During the same period, traditional sources of financing for mining companies -- commercial banks, subsidized export credit loans and long term straight debt financing in the public markets -- became less available and more expensive. Meanwhile, new markets and new financing instruments provided new alternatives for mining companies. Those companies which exploited these alternatives greatly enhanced their capacity for survival and even for profitability. This article considers the strategies adopted by some companies to adapt to changes in this recessionary environment; the inadequacy of traditional sources of financing; certain of the new financing instruments, structures and markets which have become available; and how several mining companies have utilized these new instruments, structures and financial markets to improve their competitive positions. THE IMPACT OF RECESSION ON MINING COMPANIES AND TRADITIONAL FINANCING SOURCES In its 1983 year-end article "The New Economic Order" Mining Journal characterized many of the large private sector mining companies with operations in the industrialized countries as being "gripped between the jaws of high working costs and stagnating metal commodity prices." The article went on to characterize the Canadian mining industry in particular as being "in the difficult position of having to seek to sell the bulk of its output in a world market characterized by over-capacity, where production costs were determined by internal political and economic factors while prices were set by external competitive forces of supply and demand." Miners of a wide range of commodities in the industrialized countries have come to realize that their domestic mineral resources are in many cases no longer competitive with global sources of supply. To compete and survive they would have to rely on their technical and financial expertise in mineral exploration and development and in mining and processing. Strategies For Survival Global competition has compelled management in the extractive industries to improve their worldwide cost position. This is the only means whereby a mining company can differentiate its product and attain a substantial competitive advantage. During the past decade, for example, ASARCO Inc. and Inco Ltd. chopped their payrolls, postponed expansion plans and otherwise retrenched. ASARCO reduced its capital expenditures and cash requirements for operations in 1984 to a level almost equal to its internally generated cash. The company&apos;s finances were also strengthened by increasing total lines of credit from outside sources, by selling common stock, and by reducing annual pension funding through a change in actuarial assumptions. Other companies returned to their traditional organizational structure where they had a demonstrated competitive strength. Consolidated Gold Fields, for instance, resumed its operation as a mining finance house. Its capital investment programs are now devoted solely to resource development. In mid-1984, at a time of firming zinc prices, Union Miniere S.A. used the opportunity to integrate its smelting capacity and to direct investment to certain subsidiaries at the expense of less viable operations. Smaller corporations realized that it was not enough just to be the low-cost producer. For example, Drummond Coal Company in Alabama, which dominates its regional market due to its low-costs, has also developed a world-wide trading capability and has placed incremental tonnage from its own mines as well as brokered coal produced by others, thereby minimizing capital risk. In Canada, Campbell Resources has exploited difficult times by acquiring assets cheaply. In the process it improved its capacity to withstand cyclical economic swings by diversifying from solely a copper and gold producer to a company based upon asbestos, coal, copper, gold and natural gas.

Jan 1, 1985

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere&apos; that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By D. R. Bomberger, M. Deul

An automatic microscope has been developed to measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed. In the study of coal cleaning by pseudo-gravity methods (tables, cyclones, hydrotators, etc.), it is customary to express the deficiency of the process relative to float-sink measurements in some form of "percent efficiency". These have been calculated in many different ways in order to provide a means of extrapolation of test data to untested coal feeds. This works quite well with coarse coal (here defined as larger than one-eighth in.). Large, heavy pieces of refuse are rejected rather thoroughly by many cleaning processes, and the efficiencies relative to float-sink results approach 100%. In coarse coals, the difference in the sizes of fine pyrite is masked by the averaging effect of the large coal envelopes. The existence and fate of fine pyrite is often hidden in the larger numbers representing coarse (and easily removed) pyrite. There are cases where it is desirable to subject fine coal (here defined as smaller than one-eighth in.) to cleaning processes. This is true of naturally occurring fie coal streams and in cases where comminution followed by cleaning is necessary to provide the quality desired. It is in this area that the use of process efficiency relative to float sink fails. Percent efficiencies decline to very low figures, and equivalent separation densities become a matter for conjecture. The net result is that an attempt to estimate product quality from float-sink data and a process efficiency figure often results in large errors. This work represents a new approach to the problem by observing the fate of pyrite particles, grouped by sizes, in a cleaning process. Examples are given which relate pyrite size measurements to float-sink washability and to a Deister Table operation. EXPERIMENTAL WORK The automatic microscope used here has been previously described.&apos; Briefly, it is an instrument which measures the diam of particles (as defined by a range of reflectance) exposed on a polished specimen. The instrument scans a sample briquet, measures diam of exposed pyrite inclusions and records the data by size intervals. Preparation of the briquet is critical, due to the automatic nature of the process. The principal requirement is for an optically flat surface, so that focus will be maintained as the motorized stage moves the specimen under the lens. The various substances present must be polished to the same level in spite of the wide difference in hardness between coal substance and minerals. The polishing method must not pluck out small grains, which might be rather loosely held by surrounding coal. The procedure below was successful in producing all of these results. The coal sample (8 mesh or finer) was riffled (a micro vibrating riffle is essential) to obtain 15 g. One volume of Lucite powder (thermosetting plastic mounting medium) was mixed with three volumes of coal and mixed thoroughly. A briquet was formed using a cylindrical die (1 1/4 in. diam) at 3000 lb per in.* pressure and 150°C. Preparation of the optical surface was accomplished on automatic polishing equipment, according to the following schedule: 1) Grinding: 3 stages, using successively fine Carborundum grits of 180, 320 and 600 mesh. 2) Rough polishing: 2 stages, using 3µ alumina on cast iron, followed by 1µ alumina on lead. 3) Fine polishing: 2 stages, using 0.5µ alumina on napless broadcloth over bronze, followed by 0.1µ alumina on silk filament cloth over bronze. Raw data were corrected for the fact that the chords

Jan 1, 1964

By L. D. Jaffe, H. C. Mann, E. L. Reed

It has been generally believed that fracture originates at a point and, if the stress is suficient, propagates across the material from this point. Evidence to the contrary is given in Fig 1. This micrograph shows an area close to the fracture of a steel containing The material had been quenched from 1675°F and tempered at 1150°F as a round about 10 in, in diam, and had a static tensile strength of 132,000 psi and a static yield strength of 105,000 psi. The steel was broken in 3000 cycles of reversed bending at a nominal max. fiber stress of 110,000 psi at a speed of 10,000 rpm. It was in the form of a standard R.R. Moore specimen with 45" V-notch, 0.015 in. radius and 0.220 in. diam at base of notch. The fractured edge in Fig 1 is part of the central portion of the specimen which broke during the final sudden fracture. Attention is directed to the short cracks which appear as dark lines within the specimen. Similar cracks were found in another specimen of the material, broken in 1,798,000 cycles at a nominal stress of 40,000 psi. The cracks were found in several areas close to the path of the final sudden fracture. This final fracture appeared microscopically to be wholly brittle and transcrystalline. Closer to the surface of the specimens, near the path of progressive fracture, which presumably advanced gradually during many cycles, there was microscopic evidence of some local deformation, but no microcracks. Neither were microcracks observed in areas distant from the main fracture path. The following explanation is offered: In the sudden fracture of the specimen, a crack propagates along a crystallo-graphic plane, with little or no plastic deformation of the adjacent material, until it reaches a grain boundary or a particle of carbide or inclusion which stops its advance. (The particle or boundary may be outside the plane of polish and not visible in the micrograph.) A stress concentration occurs about the end of the stopped crack. One or more new cracks are likely to start in the zone of this stress concentration. They may lie in the same grain as the first crack or in an adjacent grain. New cracks may occasionally start in a nearby but not adjacent grain whose orientation with respect to the stress leads to more ready fracture than does that of the grain between. Once started, these cracks propagate along crystallographic planes in their grains and the process repeats. This leads to discontinuous, branching chains of microcracks. As the process continues, microcracks probably tend to link up by fracture of intermediate material under the influence of increasing stress concentration. Occasionally, too, there may be a series of nearby grains of similar orientation so that there is a certain continuity of fracture across them. In either case the effective size of a crack is increased, resulting in greater stress concentration at its ends and a greater likelihood of further increase of size of the continuously-fractured region. When one continuous crack crosses the entire specimen, macroscopic fracture has occurred. The fractured edge of the specimen in Fig 1 represents a series of microcracks which became continuous across the entire specimen. The short, dark-appearing cracks in the figure did not become continuous over a large area. The row of microscopic stress concentrations at their ends may link up with those of the "main crack" outside the plane of polish. The above explanation does not imply that microcracks develop at the same rate in all portions of the specimen. They will develop most rapidly where the macroscopic tensile stress and macroscopic stress concentration are greatest. Viewed on a scale large compared to the grains, the fracture would appear to progress continuously across the specimen. Although Fig 1 shows a specimen broken in a fatigue test, it is believed that the microcracks discussed do not depend on the repetitive nature of the stressing used, since they are in the region where "sudden" fracture occurred, presumably in a single stress cycle. The whole process of microcrack propagation outlined above is thought to have occurred during this single cycle. It is believed that discontinuous crack propagation may be universal in brittle transgranular fracture of crystalline solids. Further experiments are under way.

Jan 1, 1950

By H. Dykstra

Calculated wellbore pressures were obtained for parameters of radilcs ratio and permeability. In all cases bur two, after-production was allowed to occur for one day. The calculated pressure build-up data were compared with actual pressure build-up data from a condensate well. The paper discusses the comparison, gives reasons for, inability to match calculated (2nd actual data, and presents conc1usions derived from the comparison. INTRODUCTION Considerable information has been published on the decline in wellbore pressure for oil and gas fields resulting from production of fluids. Considerable information also has been published on pressure build-up for oil fields, but relatively little has been published for gas and condensate fields. Perrine&apos; summarized the equations derived for pressure build-up in oil wells and showed how the different methods could be applied. On the other hand, very little theoretical information has been published on pressure build-up in gas or gas-condensate wells.2-4 Tracy,&apos; by pointing out the similarity between the equation describing oil wellbore pressure decline and the equation describing gas wellbore pressure decline, showed how methods of pressure build-up analysis could be applied to a gas well. In analyzing pressure build-up data for gas or gas-condensate wells, it would be very desirable to compare actual pressure build-up data with calculated pressure build-up data. Such a comparison would lead to a better feeling for the quantitative picture of gas-well build-up curves and would help to establish a degree of confidence in a given build-up curve. This paper discusses the comparison and presents conclusions made from it. Calculated wellbore pressures are given for parameters of radius ratio and permeability. In all cases but two, after-production was allowed to occur for one day. The work was done in an attempt to evaluate the reserves of a gas-condensate field. As will be discussed later, it was not possible to make an evaluation. METHOD OF CALCULATION The method used for solving the depletion and pressure build-up behavior for a gas-condensate well was that developed by West, Garvin and Sheldon.5 or the IBM 704 computer program used, it was assumed that liquid condensing out of solution would have only a minor effect on the flow behavior. Therefore, the field was treated as having single-phase flow, with the gas saturation S, remaining constant at unity minus the connate-water saturation Sw. As will be discussed later, this may not have been a good assumption. It also was assumed that oil production could be considered as equivalent gas production by using a conversion factor based on an analysis of the liquid produced. An outer boundary condition of no-flow was assumed. BASIC DATA The data required for the study were reservoir properties, fluid properties and production data. Reservoir properties included the following: thickness h, 179 ft; porosity, 0.194; connate-water saturation, 0.43; gas saturation, 0.57; permeabilities k, 1.0, 0.5, 0.25 and 0.15 md; radius ratios re/rw, 800, 1,000 and 2,000; wellbore radius rw, 5 in.; initial reservoir pressure P, 6,529 psia; and reservoir temperature, 272°F. The selection of permeabilities was based on core-analysis data showing an average air permeability of about 2 md. With a relatively high connate-water saturation, the average effective gas permeability would be about one-half, or less, of the air permeability. The selection of radius ratios was based partly on the observed rapid decline in wellbore pressure during production and partly on the fact that the well was believed to be located in a relatively small fault block. Reservoir fluid properties were obtained from a reservoir fluid study on a recombined sample of gas and condensate. Gas formation-volume factors were calculated from pressure-volume measurements made at reservoir temperature. Gas viscosities were calculated by the method of Carr, et al,G from an analysis of the re-combined sample. These data are shown as a function of pressure in Table 1. The production schedule from the gas-condensate

By L. Burris, C. H. Stockman, I. G. Dillion

Zone melting is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Equations are presented which 1—predict the concentration profiles after successive passes of the zone and 2—give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing in the last zone length. These equations were solved numerically using an electronic computer, and the concentration profiles are presented as a function of the solute distribution coefficient and the ratio of molten zone to total bar length. ZONE MELTING is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Separation occurs if the solid freezing from a solution at any moment has a composition different from that of the liquid from which it is freezing. Solutes which lower the freezing point will tend to remain in solution and will be moved in the direction of zone travel. Solutes which raise the freezing point will preferentially freeze out, and they will be moved in a direction opposite to that of zone travel. After repeated unidirectional passage of a molten zone through a bar of material, impurities will be concentrated in the ends of the bar. A limiting concentration gradient will be reached in the bar after a large number of passes of the molten zone. Both the magnitude of this limiting concentration gradient and the rate of movement of solute in any pass depend on the zone length and on the equilibrium concentrations of solute in the liquid and solid phases. The basic theory of zone melting was thoroughly covered by Pfann.1 The purpose of this paper is to extend the theory of zone melting by presenting 1—equations which relate the concentration profiles in successive passes of the zone and 2—equations which give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing* in the last zone length concentration of a given solute in the solid to the concentration of the same solute in the liquid. Analytical methods for determining the concentration profiles after any pass have been developed by Lord2 and Reiss. The method developed by Lord does not take into account normal freezing in the last zone and also becomes very complicated when the number of passes becomes large. The method developed by Reiss enables the direct calculation of the complete concentration profiles (including that in the last zone) after any pass for values of k close to unity (0.9 < k < 1.1). Both methods are useful and provide valuable insight into the zone melting process. The equations given in this article are based on the same assumptions used by Pfann. These are: 1—uniform composition in the liquid, 2—negligible diffusion in the solid, 3—constant distribution coefficient, 4—constant length of the liquid zone (except at the ends), and 5—solubility of the solute in the melt is not exceeded at any point. Equations for Concentrations in Successive Passes For a melted zone of length 1 at the left-hand end of a bar of uniform unit cross-section, the amount of solute in the liquid is J0Cn-1(x) dx [1] where the subscript is the number of the pass. Cn-1(x) represents the concentration (expressed as weight per unit volume) obtained in the previous

Jan 1, 1956

By Marshall Pease, R. J. Brandon

A UTILITY that has a large consumption of coal must insure an adequate and sound supply of fuel. The Detroit Edison Co., which has an annual coal consumption of about four million tons and spends approximately $32 million a year for coal, including freight charges, has developed a program for fuel procurement and for evaluation and selection of fuel for reliable and efficient plant operation. Fuel Procurement Coal Purchasing Division: The Fuel Supply Div. of the Purchasing Dept. combines all of the procurement functions in one group, which must maintain adequate stocks of fuel. In addition to its usual purchasing duties, the division also governs transportation, follow-up, invoice and freight bill, in cooperation with the Accounting Dept. The Fuel Div. is comprised of the fuel agent, an assistant fuel agent, a coal buyer and five coal clerks, who follow the movement of each car, initially approve freight bills and invoices, and file claims whenever there is a shortage of one ton or more. The fuel agent reports directly to the purchasing agent of the Company, and all major programs are planned jointly with the chief purchasing officer. The apparent individuality of the fuel section is necessary because of the tremendous volume of coal cars handled each day, sometimes as many as 500, which must be handled promptly to complete the fastest possible move from the mines to the plants. Determining Annual Coal Volume: Through the combined studies of a Production Dept. Load Committee and the Controller&apos;s office, accurate predictions of coal requirements for any given year are provided the Fuel Dept. from 12 to 15 months in advance. This is divided into the requirements of all individual power plants and central heating plants. This in turn determines the quantity and quality for plants whose specific fuels vary with the type of equipment installed. In the Detroit area, which has a high industrial load, early estimates of annual coal consumption usually are resolved at the end of the year within 4 or 5 pct of the original plan. Operating in a highly developed industrial area eases the task of estimating primary output; and, with the residential demands increasing in a steady and fairly well-defined pattern, the overall coal schedules are not subject to radical changes during any given year. Selecting Suppliers: At any time, but especially during or before an emergency, the coal supply factor must be made secure. This is particularly true in the procurement of utility fuel. There are always extreme quantities of so-called "bargain" coal available during the buyers&apos; markets, such as recently prevailed. These opportunistic offerings may be considered a means of averaging down overall price, rather than as a steady and dependable supply source. Coal is purchased on contract from mine operators and sales agents who have proved reliable. They are not opportunists who desert for higher dollars in times of duress; they do not fail to fulfill contracts when markets rise or overship when markets dip. The progressive operator today who is willing to expend capital to improve quality and service deserves much more consideration than a matching of short-term pennies. When a company has a high volume of annual needs, all phases of the mine supply must be considered. The mine must be able to produce the quality required at a fair price and be able to sell oversizes of coal in enough volume to screen sufficient nut and slack. It must crush coal and sell mine run at prices in line with competitive nut and slack and be willing to do so when there is no demand for prepared sizes. Determining Price: The public utility is in direct competition with any of its customers who can, if savings are guaranteed, generate their own power. Today, to a greater extent than ever before, private industry must do a better overall job than Government-controlled operations. The price of coal must be realistically balanced with the price paid by almost all industries and the railroads as well. The supply-demand ratio in coal is not difficult to discern. There is access at all times to Govern-

Jan 1, 1952

By Ralph Hultgren

IN solid solutions atoms of differing sizes occupy the same crystalline lattice, requiring that some of them be compressed and others expanded. The energy involved has been called misfit strain energy and is an important concept of crystal chemistry. If the atomic sizes and elastic constants of interatomic bonds are known, the misfit energy may be calculated,&apos; provided certain simplifying assumptions are allowable. Usually, isotropic crystals are assumed and interatomic distances are taken to be the statistical average determined from X-ray diffraction. Such calculations yield values of the misfit energy of the order of 1 or 2 kcal per atom in alloys such as Au-Cu at compositions of 50 atomic pct. However, evidence has accumulated in recent times that atoms change their sizes with composition of alloys, implying electronic rearrangement of the bonds. The size changes have been found particularly by application of the X-ray method developed by Warren, Averbach, and Roberts.&apos; Thus, Averbach, Flinn, and Cohen3 determined radii in Au-Cu alloys. Oriani4 showed that these new radii led to a calculated misfit energy in disordered AuCu, which was decreased from the values calculated by the usual theory more than twenty-fold, to only 80 cal per g atom. Thermodynamic calculations from the phase diagram5 also show misfit energy to be no more than a few hundred calories per g atom in this alloy. The question of what electronic rearrangements are possible therefore becomes compelling in estimating misfit energy. In the following pages the results of certain calculations on the AuCu tetragonal superlattice are submitted. Conclusions drawn from these should be applicable in large degree to disordered solid solutions. As in all ordered states, bonding distances in the superlattice are individually known, rather than being merely average distances as found from lattice constants of disordered states. Moreover, only the Au-Au and Cu-Cu distances are strained; the elastic constants of these are known in the elementary state. In the usual calculation it is necessary to assume elastic constants for Au-Cu bonds. Misfit energy has thus been calculable without the need of many simplifying assumptions usually made. It is still assumed that equilibrium bond lengths and elastic properties of the bonds are the same in the alloy as in the pure metals. As previously discussed, this is probably not correct. Also assumed is that the bonds are not affected by strain of neighboring bonds. A calculation of Young&apos;s modulus from compressibility data shows this to be far from true; extensive electronic rearrangements take place. It would seem that misfit energy cannot be calculated from elasticity data for the elements. The usual methods may, however, give an upper limit which is often much higher than the true value. The question of electronic rearrangement is, of course, a complex one. Pauling&apos;s theory gives a simple, approximate treatment of the relation between type of bond and bond distance. This has been applied with some success to the Au-Cu system, as will be shown in a later section. Misfit Energy in Au-Cu Alloys Hume-Rothery and Raynor6 discuss the Au-CU system as a type example of strain energy. The gold atom is 12.8 pct larger in diameter than the copper atom, near the size factor limit beyond which solid solubility is severely restricted. They therefore consider the misfit energy to be large, a conclusion for which they believe they find evidence in the phase diagram. Gold and copper are completely miscible in the solid state, but the alloy has a minimum melting point at an intermediate composition. From this Hume-Rothery and Raynor conclude that the strain energy is nearly large enough to prevent miscibility; the phase diagram tends toward a eutec-tic type. In Ag-Cu, which has almost identical size relationships, solid miscibility is quite limited; whereas in Au-Ag, where atomic sizes are nearly the same, there is complete miscibility without a minimum in the melting point. From their arguments the heat of formation of Au-Cu would be expected to be endothermic or only slightly exothermic, that of Ag-Cu to be endothermic, and that of Au-Ag to be exothermic. Deviations, from Ve-gard&apos;s law of additivity of atomic radii support these conclusions, since Au-Cu and Ag-Cu both have pronounced positive deviations, and Au-Ag has a negative deviation. Nevertheless, Au-Cu alloys form exothermically; indeed, considerably more exothermically than Au-Ag, Table I. Hence, strain energy must be much less important in this case than Hume-Rothery and Raynor have supposed.

Jan 1, 1958

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified; indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will he welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 12, 1913

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore exploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composition laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a&apos; run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, variations are functions of distance. Hence. in either case, variations along the hole are of greater effect than across it. Let us examine Fig 1 briefly to observe a cross section of a unit of depth of a typical diamond drill hole. If we neglect radial change in chemical composition, which we have seen is small compared to lengthwise variation, we can see that if core recovery was 100 pct, the core and its surrounding area, which would be recovered as cuttings (assuming 100 pct sludge recovery), must analyze the same if the sampling is perfect. This is the foundation of this paper, namely, that if core recovery is complete we may assume that the core constitutes as nearly as possible a perfect sample of the ground drilled. Now let us pass to the methods of weighting core and sludge in the final analysis and then develop each in turn. One might employ core analyses only, sludge analyses only, or apportion the influence of each by one of several methods. The most common apportionment is by direct proportion to relative theoretical vol- &apos; ume occupied by each component in the cylinder hollowed out by the drill, known as the Longyear formula. Another logical treatment would be to consider core and sludge in the final analysis according to the weight of each recovered. This procedure was elaborately set forth and refined by R. S. Moeh1man.l Then to be sure that we have embraced all the possibilities, we must admit that some other method or methods may be devised empirically or by mathematical maneuvers. Should a drill machine be capable of recovering 100 pct of the core in all types of rock, certainly core alone need be analyzed and no complicated mathematics are required; but although some companies have had fair success in obtaining high percentages of core in certain homogeneous ores on the Mar-quette Range, their same methods have proved disappointing on the Menominee, Cuyuna, and Gogebic Ranges where the iron formation often varies widely from flinty chert beds interstratified with soft hematite to wholly leached ore material composed of an unpredictable mixture of hematite and limonite with occasional zones of sugary, recrystallized chert. In spite of numerous mechanical improvements in core barrels, few drilling programs can count on complete core recovery. The sludge alone might be analyzed but for practical reasons this is inadvisable when core is obtained due to the numerous opportunities for contaminating or losing portions of the cuttings. The Longyear formula involves a weighting of the core and sludge in proportion to the theoretical volume of each, that is, where the volume of the core recovered is one-third of the total cubic volume of the cylindrical hole made by the drill, the analysis of the core is given one-third of the weight in the final analysis. This approach to

Jan 1, 1950