Search Documents

By A. U. Seybolt, F. J. Norton

A standard technique for heat treating small metallurgical samples where no appreciable contamination from the atmosphere can be tolerated is that of sealing small samples in evacuated fused-silica tubes. Since vitreous silica is relatively impervious to diffusion of gases, even at temperatures approaching the devitrification range, around 1100°C, this simple procedure has been very widely adopted as a standard technique in metallurgical research. Many workers have recognized that, with metals of fairly high reactivity, insulation from direct contact with the SiOz envelope is desirable in order to avoid displacement reactions of the type M + SOz-- MOz + Si(in M). It is not so generally known, however, that the 'rate of permeation of oxygen from the air through the SiOz enclosure at tem-

Jan 1, 1964

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 8, 1979

By Stanley M. Miller

The probabilistic nature of appropriate geologic variables can be included in analyzing the stability of potential slope failure modes. Random variables in the two-dimensional plane shear analysis of a specified structural discontinuity include the shear strength and waviness angle of the discontinuity and, in some cases, the rock mass density. Estimated probability density functions that describe these random variables are combined by Fourier analysis to produce an estimate of the safety factor probability density function, which appears to approximate a gamma distribution. The probability that sliding will occur along the specified structure is equal to the area under this density function where the safety factor is less than one.

Jan 1, 1982

By Charles H. Jacoby

A decision was made by the management of International Salt Co. in 1960 to eliminate all waste products which were entering the waters of Lake Seneca. This was to be accomplished by the injection of waste slurries into an abandoned brine cavity. The effluent from the cavity was to be treated and used for the manufacture of salt or disposed by deep well injection into the Cherry Valley limestone. After several years of research and design, a construction permit was granted by the state of New York; the injection, recovery, and disposal wells were constructed and after a public hearing an operational permit was issued. A summary of the operational results of the system is given.

Jan 1, 1974

By John A. Ames

AMERICAN pioneers first discovered "commercial" salt in western New York State. Geologists gave the classically correct name of Salina to the salt bearing strata of New York. Rock salt occurs in rocks of approximately the same age and stratigraphic position as New York's Salina "group", to the south and southwest, in western Pennsylvania, eastern Ohio and northwestern West Virginia. Sodium chloride and associated salts occur in brines throughout much of the same area as the rock salt. Brines also are found in areas well beyond the margins of that under which the rock salt lies, especially to the west in Ohio and to the south in West Virginia. The occurrence of the brines in the same area as the rock salt is almost always coincidental rather than indicative of a physical association.

Jan 5, 1950

By K. Aoki, N. Kameda, T. Esaki

The shortage of adequate construction sites and their difficult location has compelled many engineering structures to be planned in old mining areas in Japan. This paper shows, first, the characteristics of the excavated underground environment and next, the necessary preventive measures during construction of surface structures. Where the depth of a mined out area is relatively shallow, there is a tendency of cave-in consequent to surface loadings. The effect of surface loadings is inversely proportional to the depth of goals. Finally, a power plant project is studied as an example.

Jan 1, 1984

By T. M. Howell

JET piercing is a licensed process developed by Linde Air Products Co. Experiments with this method lapsed during World War II, but in the decade that followed the process was expedited. Two types of drills mount the jet piercing equipment for blastholes. The turntable of one machine rotates the complete stem system as well as the blowpipe, which emits three individual flames at different levels. Depth penetrated is limited by length of the blowpipe mounted in the rotary mechanism. This machine has successfully drilled blast- holes in Minnesota taconite.

Jan 6, 1957

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Metallurgist wanted for research in iron and steel. Man with experience in mills preferred. Salary $4,000. No. 13. Opening for a few technical graduates to act as instructors in mining to men at the mines under the supervision of the State mine inspector. Salary $1,800 per year. No. 14. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Mining engineer and metallurgist open for engagement, as superintendent of mines or constructing engineer. Technically educated, with 14 years' experience in United States and Latin America in concentration, amalgamation, cyaniding, constructing. Just finished building large modern all-sliming cyanide mill in Central America. No. 18.

Jan 4, 1914

By R. J. Wasilewski

OBSERVATIONS have been made that the substitution of antimony for bismuth in Bi2Te3 leads to anomalies in some of the electrical and magnetic properties of the Bi2Te3-5S2TeS alloy system at the composition ratios 2 Bi2Te3 : 1 Sb2Tes and 1 Bi2Te3 : 2 Sb2Te3. Airapetiants and Efimova1 have reported the peaking of the nondegenerate hole mobilities, at these compositions for sintered materials and ascribe the peaking to the formation of ordered alloys. From a study of these materials produced by the Bridgeman

Jan 1, 1962

By A. Berthet

In the past two decades, of the successive steps leading from iron ore to finished steel, the production of liquid steel and its preparation for the casting operation has probably undergone the most drastic evolution. The reason for this is the development of oxygen converters (top blown and later on bottom blown) and UHP arc furnaces which are replacing the conventional processes such as the open hearth and basic Bessemer processes. These new processes have been great advances, but it would certainly be quite hazardous to assert that the situation will remain the same for the coming decades. In fact, with the advent of continuous steelmaking a new generation of processes has now arrived. The research and development programme at IRSID on continuous an a steelmaking began ten years ago has progressed systematically in the following stages : First a comparison was made on a small pilot scale of various techniques : for example, refining in a runner by top or bottom blowing, pulverizing the metal stream by oxygen, using the mixing effect of a vortex, etc. but for various reasons these processes proved unsatisfactory and were abandoned in favour of a method using the so -called "emulsion refining".

Jan 1, 1972

OF no less importance nor less terrifying to consider than the marvelous effects of guns are those produced with fire by powder in underground mines. These are truly not only similar to fearful natural earthquakes, but it can perhaps be said that these made by art surpass the wrath of the earth with greater effect. For if the latter shakes it happens that it causes the things on the surface to shake and sometimes to fall into ruins, but the former not only shakes but always functions and destroys-surely a marvelous effect which is almost incomprehensible, and if experience did not demonstrate it, it could scarcely be believed. Who would say that the mountains, things of such great hardness, would yield to men, easily opening their bowels? Likewise, one who had not seen it would say that it was impossible for men to have a way of administering at will fearful and destructive thunderbolts which are of such a kind that, although men make them, they cannot protect themselves against them; indeed they cannot call themselves safe from the evilness of gunpowder even in mountains composed of very hard stones or in budded structures. For, as is seen, there is no seemingly impregnable fortress that does not yield when guns are brought near it. If it happens, indeed, that guns can- not be brought near to some place because of the harshness of the site,

Jan 1, 1942

By George Laird

IF IT IS true that Sir Walter Raleigh lost his head for his failure to find gold in the Guianas, the trumped up charge of "treason" might better have been "con-tributory negligence." That systematic investigation and development of the gold-bearing areas of both Dutch and French Guiana have not been accomplished is not due so much to the lack of gold as to the geo-graphical, physical and climatic conditions of the two colonies. The Dutch, as a people, are not prospectors. The French look upon "Cayenne," or French Guiana, as DJOEKA BOATS USED IN RIVER TRANSPORTATION. just what it is: a penal colony, which produces a certain amount of balata, gold and essential oils, all of which can be purchased from the natives with far less physical exertion than they can be secured from the "bush" or jungle. The colonies have had their gold "booms," and dur-ing these periods the production has increased to a considerable amount, but the hardships to be endured in reaching the fields, the cost of transporting tools and supplies, the ever-present fevers, the bite of the "57 varieties" of insects and, lastly but not leastly, the abundance of rum in the seaport towns, dampen the ardor of even the strongest; the production of gold is left to the "pork knocker" or illegal gold digger and to the comparatively few producing "mines."

Jan 10, 1922

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all weep-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 3, 1914

By P. Barnes

The object of this paper is to make a brief comparison of the outlines of several forms of ports for steel-melting turnaces, in reference chiefly to the proper mixture; of the gas and air, and to the direction in which the flame is thrown down into the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M, Pernot, of St Chamond, France. This is used with the dome roof preferred by him fur the revolving bottom that bears his name. From No. 1 has been derived No. 2. This is shown on the plans of Mr. A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched roof of nearly the ordinary form, instead of over the top of the roof, as with the dome of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or " washing "-—to use the briefer French term. in this the gas and air come into contact in broad sheets one above the other, Fig. 5 shows the form used by Messrs. Richmond & Potts

Jan 1, 1881

By P. Barnes

THE object of this paper is to make a brief comparison of the out-lines of several forms of ports for steel-melting furnaces, in reference chiefly to the proper mixture of the gas and air, and to the direction in which the flame is thrown down into. the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M. Pernot, of St Chamond, France. This is used with the dome roof preferred by him for the revolving bottom that bears his name. From No. I has been derived No. 2. This is shown on the plans of Mr., A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched. roof of nearly the ordinary form., instead of over the top of the roof, as with the done of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or “washing” -to use the briefer French term. In this the gas and air come into contact in broad sheets one above the. other. Fig. 5 shows the form used by Messrs, Richmond & Potts

Jan 1, 1881

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By John V. Beall

Probably the only hotel in the world with near 100% occupancy at all times is the modern Hotel Indonesia in Djakarta. However, there is little gaiety among the scores of business men who occupy the hotel because they fret as days grow into weeks in seemingly interminable negotiations with government officials. As one man put it, "time is a dimension that they [Indonesians] have never grasped." But the visitors still come in droves to investigate business opportunities in this sprawling nation of tropical islands which is, with 120 million people, the fifth largest nation in the world. Approximately $300 million is being spent each year in Indonesia by foreign companies and governments. Aid grants from the latter are derived about one third from the United States, one third from Japan and the remainder from many nations. Djakarta is a far cry from pleasant colonial Batavia, as the city was called under the Dutch. The orderly colony of prewar days was managed as an agricultural and trading dependency of Holland. The Dutch did little about educating the people. The islands were controlled by the Japanese during World War II and afterwards there was a war for independence--which was attained in 1949. In the ensuing years, President Sukarno devastated the economy by squandering money on a gigantic scale. A Communist-attempted coup in 1965 resulted in a military takeover and the extermination of Communists. The new government under Suharto, which took over all power in March 1966, found itself in a situation where bare survival was the first consideration.

Jan 1, 1970

By Robert Anderson Cook

The subject of refractory materials occupies such an important position in all metallurgical works, and particularly in those of iron and steel, that any data concerning it must be of interest to the metallurgist. No apology is needed, therefore, for this attempt to describe the mining of fire-clay and the manufacture of fire-brick at one of the largest establishments in this country. Mount Savage is a small village situated in the northwestern part of the Cumberland coal basin, on the Cumberland & Pennsylvania Railroad, and at the foot of Savage Mountain, from which the village takes its name. Fire-brick have been manufactured here almost, if not quite, as long as in any place in America; and as the brick are still shipped to nearly half the States in the Union every month, the manufactory is probably the most generally known. In the year 1837, a company was formed called the Maryland & New York Coal & Iron Company. It built two blast-fiirnaces, the ruins of which still remain. It was in the construction of these filmaces that the first fire-brick made here were used ; and though the iron works ran but spasmodically, the brick works have been in constant operation ever since. From 1837 until 1846, the Maryland Coal & Iron Company, from then until 1548, the Lochiel Iron Co., and from 1848 until 1861, the Mount Savage Iron Co., ran the brick-works, and in

Jan 1, 1886

By Kenyon E. Richard, James H. Courtright

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district's history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial de- lineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper.

Jan 11, 1954

By Paul Queneau

Some years from now, perusal of the unfolding saga of the nickel family will show that the year 1968 was the herald of change-both in the geography of its endeavors and in its technology. No one should doubt any longer that oxide ores of nickel have come of lusty age-their heavyweight stature in the Caribbean area and in the Western Pacific can be shrunk only by immersion in the politics of unhappiness. The sulfide branch of the family has been augmented afar off by substantial ore deposits in western Australia-right across the globe from Sudbury-and in southern Africa, 9000 miles from the nickel hub. The Foreword of the 1961 AIME volume, dealing with the extractive metallurgy of copper and nickel, noted that "the dead hands of nitrogen" had been lifted from oxidation reactions utilizing air and that the industry was on the threshold of under- standing this fact. Here, at least, nonferrous industry had led its ferrous counterpart in the commercial use of tonnage oxygen in liquid phase pyrometallurgy-the reference is to oxygen flash smelting. Today large oxygen-producing plants are blossoming everywhere and the fruits which will follow are many and varied. Among them is Inco's forthcoming use of the top-blown oxygen converter for sulfide melts. The bell tolls for those "pyro- metallurgical dinosaurs" which still stalk smelter aisles the world around. Silicate oxide nickel ores will rejoice in the glow of modern elevated temperature chemical metallurgy in its various manifestations, vindicating the bulldog spirit of that ancient of clans, the hot metal men-including the renovator of Le Nickel's Doniambo Works.

Jan 10, 1968