Search Documents

By Ian William Wark

DIFFERENT parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter tempera-tures. It will be shown in this paper that the temperature is of con-siderable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation.

Jan 1, 1938

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By R. B. Haagensen, E. Martinez, V. Kudryk

The sample under investigation contained approximately 16% BaSO, and was 80% -325 mesh. Established methods for floating barite did not produce concentrates of satisfactory grade or barite recovery because of low barite content and the presence of 6% calcite in the feed. By using a new long-chain sulfosuccinamate collector in combination with relatively high concentrations of sodium silicate, a barite concentrate was produced that would be acceptable as an oil-drilling mud using a simple rougher-cleaner circuit. No desliming of the fine-ground feed was necessary. Barite recovery was over 80% and the concentrate produced had a specific gravity higher than 4.3. During the course of the investigation, a procedure was developed to obtain semiquantitative determinations of barite, calcite, quartz, and feldspar in test samples using an infrared spectrophotometer. Samples were also analyzed in a thermobalance for determination of the calcite content. The use of these instruments made it possible to obtain quick mineralogical assays and proved to be of invaluable assistance in guiding the flotation testing.

Jan 1, 1976

By George W. Lower, Robert B. Booth

The use of cyanides in the extraction of gold and silver is well known1 Such extractions employ concentrations of cyanide in the range of 0.02-0.25% sodium cyanide equivalent in leaching cycles of 24-48 hr and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold.2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure.

Jan 11, 1965

By C. D. Hunter, I. B. Browning, Ralph Thomas

Production of oil in Kentucky during 1938 was 5,566,154 bbl., showing a substantial increase over that of the year 1937; while in the gas areas development was somewhat retarded although deliveries were similar to those of 1937. In eastern Kentucky there was an oil increase during 1938 of over 150,000 bbl. above that of 1937. No new pools were developed and the increase was almost entirely due to the installation and expansion of secondary recovery methods and to the further development of the Maxon and Big Lime, Mississippian pools in Floyd and Martin Counties. With this development eastern Kentucky reached a level near that of 12 years previous, when the development of several large producing areas had just been completed. In eastern Kentucky during 1938 not over 50 gas wells were completed. Although the pipe-line deliveries were approximately the same as during 1937, development was retarded because of an excess of gas already developed and the intensive development of the Oriskany fields in West Virginia. In western Kentucky, in the part of the Illinois Basin lying in the state and known in Kentucky as the Western Coal Basin, the increase was due to the discovery of a number of new pools, the largest and the one producing the biggest wells being known as the Birk City pool. In fact, the discovery of this pool with the McClosky "sand" (St. Genevieve limestone) as the producing formation was in a large measure responsible for the increased activity, which in turn brought the discovery of the other areas. The discovery well in this pool is the C. T. Blackwell, which came in flowing 1000 bbl. daily from the McClosky sand at a depth of 1870 ft., drilled in April 22, 1938. This discovery, coming at a time when the major companies and many others were conducting an intensive leasing campaign and making extensive subsurface and geophysical surveys in the deeper part of the basin, resulted in renewed activity over the entire area and brought much new drilling. It also brought to Kentucky for

Jan 1, 1939

By C. D. Hunter, I. B. Browning, Ralph Thomas

Production of oil in Kentucky during 1938 was 5,566,154 bbl., showing a substantial increase over that of the year 1937; while in the gas areas development was somewhat retarded although deliveries were similar to those of 1937. In eastern Kentucky there was an oil increase during 1938 of over 150,000 bbl. above that of 1937. No new pools were developed and the increase was almost entirely due to the installation and expansion of secondary recovery methods and to the further development of the Maxon and Big Lime, Mississippian pools in Floyd and Martin Counties. With this development eastern Kentucky reached a level near that of 12 years previous, when the development of several large producing areas had just been completed. In eastern Kentucky during 1938 not over 50 gas wells were completed. Although the pipe-line deliveries were approximately the same as during 1937, development was retarded because of an excess of gas already developed and the intensive development of the Oriskany fields in West Virginia. In western Kentucky, in the part of the Illinois Basin lying in the state and known in Kentucky as the Western Coal Basin, the increase was due to the discovery of a number of new pools, the largest and the one producing the biggest wells being known as the Birk City pool. In fact, the discovery of this pool with the McClosky "sand" (St. Genevieve limestone) as the producing formation was in a large measure responsible for the increased activity, which in turn brought the discovery of the other areas. The discovery well in this pool is the C. T. Blackwell, which came in flowing 1000 bbl. daily from the McClosky sand at a depth of 1870 ft., drilled in April 22, 1938. This discovery, coming at a time when the major companies and many others were conducting an intensive leasing campaign and making extensive subsurface and geophysical surveys in the deeper part of the basin, resulted in renewed activity over the entire area and brought much new drilling. It also brought to Kentucky for

Jan 1, 1939

By G. S. Hume

In Alberta, an oil well with an estimated capacity of 60 to 100 bbl. was "brought in" at Wainwright, the oil being derived from the Colorado group of rocks. In the Norman fields, Mackenzie River area, two new holes completed showed no oil in commercial quantities whereas the "Discovery" well has now an increased flow amounting to about 100 bbl. In Kent Co., Ontario, a well from low down in the Trenton formation gave an initial flow estimated at 200 bbl. This opens up new possibilities for the Ontario fields as this is the first oil from this depth in the Trenton. ACTIVE drilling operations for oil were carried on during the summer of 1923 in various parts of western Canada, particularly in Alberta. During the early part of the summer, interest centered in southern Alberta, in the Coutts area, just north of the producing Kevin-Sunburst field of Montana; but on Nov. 14 a strike of oil by British Petroleums Ltd. at its well near Wainwright, 120 mi. east of Edmonton, diverted public attention to a new field. According to present estimates, this well has a possible production of from 60 to 100 bbl. a day; the oil is 15° Bé. with an asphaltic base and is obtained from a sand at the depth of 2019-2036 ft. The oil stands at 1700 ft. in the casing and there is sufficient gas pressure to cause it to flow when the well is opened. The oil horizon is in a sandstone in rocks of Colorado age. It is known that there is a terrace structure of which the western edge extends in a northwesterly direction from the vicinity of Hardisty to Viking, where it probably swings more to the north. At Viking a small dome-like structure on this terrace gives rise to an important gas field. Wainwright lies directly northeast of Hardisty. The exact structure in the Wainwright field is unknown. At Fabyan, 6 mi. northwest of Wainwright, the Imperial Oil Co.1 last year brought in a large gas well estimated at 14,000,000 cu. ft.; the escaping gas sprayed a small amount of heavy black oil over the derrick. The gas was obtained at a depth of

Jan 2, 1924

By R. E. Gilmore

This paper is a revision of a former paper published in mimeograph form by both the Canadian and American coal classification committees, and is now presented for the purpose of acquainting those interested with the present status of coal classification in Canada. The classification employed for "Customs purposes" is detailed, and the classification schemes from which the customs classification was derived are reviewed and discussed. The activities of the Canadian coal classification committee, namely, the Associate Committee of Coal Classification and Analysis of the National Research Council, is also reviewed. Reserves, Production and Uses of Canadian Coals The total coal resources of North America are estimated to be 69 per cent. of those of the world, and of this portion, the distribution is 52 per cent. for the United States and 17 per cent. for Canada. Accordingly, Canadian coal resources amount to approximately one-third of those of the United States, and one-sixth of those of the world. As for the geographical distribution, the bulk of the known coal deposits are in the extreme eastern and western portions of the country. Employing the usual, more or less loosely defined, designations for the different classes and subclasses of coal, the distribution of the Canadian coal resources, according to provinces, is as follows: Maritime Provinces: Nova Scotia and New Brunswick Bituminous and semibitu- minous coals. Ontario (northern part).............................Lignite. Saskatchewan, (and Manitoba)....................... Lignite. Alberta and British Columbia........................ Lignites, subbituminous, all kinds of bituminous, semibituminous and semianthracite coals. Of the total reserves, roughly 92.5 per cent. is credited to the noncok-ing lower rank subbituninous and lignite groups, the bulk of which are

Jan 1, 1930

By John A. Mathews

It is no longer necessary to explain to an audience like this that there are stainless or non-corrosive steels. It is still necessary to repeat, and to keep on repeating, that no one of them is stainless or non-corrosive under any and all conditions. We do not make railroad axles, springs and rails from the same kinds of steel; nor are shafts, steering-arms, gears and cap-screws made from the same type analysis. By analogy with other fields of endeavor, therefore, it is logical to expect that all the myriad conditions of corrosion due to inorganic and organic acids and salts and their mixtures in all degrees of concentration and at a wide variety of temperatures and pressures will require different materials to withstand them. Possibly stainless steel when first introduced a decade ago was expected to do too much, or suffered from overenthusiasm and lack of positive knowledge and experience on the part of its producers. Its name may have been a bit misleading too, for remarkable as this product is, it has its limitations. There are now so many different ferrous products available and calling for recognition, that we may be justified in an attempt at classification. The first division is very simple. 1. Non-corrosive steels that harden by quenching. 2. Non-corrosive steels which do not harden by quenching. We might make the classification still simpler by saying (1) those that harden by quenching, and (2) those that soften by quenching. Of course there is a border line or fringe of compositions which may possess some of both qualities under limited conditions of treatment. I have seen a steel so perfectly balanced on this border line that in its natural condition, as rolled, the outside of a 1-in. bar was soft and the inside hard, and there was quite a sharp line of demarcation in between. The hardness at the center was more than twice as great as at the surface, as measured by the Rockwell test. This border line of products does not include, however, the commercial products now available to solve the problems of industry. Let us examine the products of these two classes: Hardenable Non-cokkosive Steels This group, practically speaking, includes only the products known as "stainless iron and stainless steel." These names have a special sig-

Jan 1, 1927

By Roy Hardy

THE Getchell mine is a comparatively recent discovery in the old Potosi mining district, Humboldt County, Nevada, a district organized in the seventies and eighties, in which some prospecting was done in several metamorphic zones along a monzonite-sedimentary contact. The district had no production in the early days and no further work was done until the same metamorphic zones were prospected for tungsten (scheelite) in 1917 and 1918, when a few small lots were shipped. It again lay dormant until 1934, when prospectors investigated a large siliceous escarpment at one end of the old district where outcroppings were a prominent feature of the topography. Undoubtedly, during the early prospecting of the district, the outcroppings had been investigated for mineral, probably by panning, with negligible results because the gold later found is invisible in the concentrate and is refractory. A fire assay revealed the presence of sufficient gold to warrant develop-ment work. The outcroppings were easily prospected by short tunnels having their portals in the siliceous material on the hanging-wall side, with a maximum distance to crosscut to the footwall of 135 ft., or a distance at right angle to dip of 60 to 90 ft. Development work, reaching a depth of over 600 ft. on the dip of the vein, was done by means of various crosscut tunnels, winzes and laterals. A churn-drill hole was also sunk, which intersected the vein at a depth of 1100 ft. on the dip. Sufficient development work of this character was completed by 1937 to justify the erection of a reduc-tion plant to roast the sulphide ore and cyanide the calcine, and to treat the oxidized ore by straight cyanidation, to make a doré bullion for shipment to the mint. The erection of the plant was started that year and finished early in 1938, with a combined capacity of about 800 tons per day. It has operated continuously since erection and recently was enlarged to handle 1000 tons per day. The vein dips with the slope of the mountain, and by stripping the hanging wall the ore may be mined by power shovel for several hun-dred feet below the outcrop. Thereafter underground methods will be necessary.

Jan 1, 1940

By E. S. Bardwell, Roy H. Miller

During the period extending from May, 1922, to September, 1923, the copper-refining furnaces of the Great Falls Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont., were operated exclusively with pulverized coal as fuel. The installation was made first as an experiment. It proved successful from the start and was abandoned solely because fuel oil from the Sunburst field became available at a price sufficiently low to be more desirable from an economic standpoint. The equipment required for pulverized coal has, however, been kept intact and is available for immediate use should the oil supply fail. Inasmuch as pulverized coal had been used on two large reverbera-tory smelting furnaces and was, at the time we were considering its application-to the copper-refining furnaces, being used on the Wedge furnaces roasting zinc concentrate for the electrolytic zinc plant, we were equipped with a coal-pulverizing plant of ample capacity to supply pulverized coal for the furnace refinery. The only problem was to devise suitable means for transporting pulverized coal from the pulverizer plant, located in the smelter building, to the refinery about 3000 ft. distant and about 150 ft. above the level of the pulverizer plant. When studying this installation, it should be borne in mind that the layout represents an adaptation suited to the existing conditions at this particular plant. The installation was entirely satisfactory and uniformly dependable but might be modified to advantage from an operating point of view if an entirely new installation were being planned. Fuel Supply The use of the local coals, high in ash and sulfur, was abandoned some time before coal-dust firing was attempted. Local coals from the Great Falls field carrying an average of 4 per cent. sulfur and 22 per cent, ash were used with fair success in the small furnaces in use prior to 1916. In the 250-ton furnaces, however, the time lost in grating and removing clinker from the fireboxes, as well as the difficulties incident to the high-sulfur content of the fuel, became serious and recourse was had to the

Jan 1, 1927

By William G. Krantz

The increased service demands on some of the products of the National Mallcable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process had already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 Ib. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give US good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 04 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect. In proper operation lies the whole secret of success. That steel has been made electrically means nothing, for when the furnace is operated under oxidizing conditions the quality is no better than that of open-hearth material; but when properly made, electric steel is as good as

Jan 1, 1916

By Forbes K. Wilson

Dick Hunt is known for having said, "Ore bodies are found but mines are made." This was certainly true of the Ertsberg-it was stumbled upon, literally, by a group of mountain climbers, but to develop it into a mine took 12 years of concerted effort. For more than a century, explorers had attempted to penetrate the jungles of New Guinea and climb the snow-covered Mt. Carstensz, named for a Dutch navigator who first saw it in 1620. But the first to succeed was the Colijn expedition which reached the 5030-m (16,500-ft) pinnacle in December 1936 after starting out from the south coast57 days earlier. Members of that expedition were A. H. Colijn and Jean Jacques Dozy, employees of Shell Oil Co., and Lt. Wissel, a pilot in the Royal Dutch Navy.

Jan 6, 1977

By Arthur Redfield

THE year 1923 was marked by slight progress in exploring and developing the petroleum resources assumed to exist in Central America. Actual drilling for oil took place only in Costa Rica and Panama. The Sinclair Consolidated Oil Corpn., through its subsidiary the Costa Rica Oil Corpn., drilled in southeastern Costa Rica.. Its, Panaman subsidiary is reported to have abandoned drilling in Bocas del Toro. The Texas Co. drilled in Chiriqui, and the Panama Gulf Co. in Garachiné, Province of Darién. No oil was obtained in any of these wells;' shows of gas were met in Costa Rica. Concession hunting continued during the year. A number of concessions, several of which appear to be purely speculative, were submitted for ratification. Some confusion has been caused by overlapping concessions and claims to oil lands, caused partly by the imperfection of existing maps. A conflict between the Sinclair, and Gulf companies in Panama has been compromised. The Amory concession in central Costa Rica, held by the British Controlled Oilfields, Ltd., was voided by decision of the arbitrator, Chief -Justice Taft. Geologic exploration took-place in Guatemala and in Panama. The chief contribution of the year to Central American geology was a description by Katherine Van Winkle Palmer of Lower Miocene foraminifera and mollusks from southeastern Costa Rica. A new petroleum law was promulgated in Panama.

Jan 3, 1924

By R. W. Heckel, J. H. Smith, H. W. Paxton

The habit plane of proeutectoid cementute precipitated from austenite was studied using a two-trace surface (analysis coupled with a direct X-ray back-reflection determination of the orientatzon of the parent Matrix. The results were the same as those obtained by earlier workers1 - 2 who used Indirect methods to determine the orientation of the matrix. The data indicate that a range or habit planes in the parent phase is operative which is not in agreement with accepted existing theories. In 1933, Mehl, Barrett. and smith1 obtained a non-unique result in a study of the Widmanstätten habit plane of proeutectoid cementite. Their data are shown in Fig. 1. These results were verified by Greninger and Troiano,2 although they did not pre-sent any data. Both of these investigations relied upon indirect methods of determination of the matrix lattice orientation. Theoretical considerations of Widmanstatten precipitates have usually proved or assumed an orientation relationship between matrix and precipitate; the habit plane expressed relative to the matrix is generally unique, although it may be irrational.3 Opinion is divided as to the factors influencing the choice of habit plane. Mehl4 felt that a nucleus which was plate shaped to minimize strain energy and surface energy during its formation could maintain this shape by the point effect of diffusion; the

Jan 1, 1961

By Thomas W. Yardley

In many years' experience as a maker and purchaser of cast-iron coated pipe, I have never met with any standard form of specifications for such. Each water-works company, employing a hydraulic engineer, has, under his direction, prepared complete specifications for the particular conditions required; but I cannot find that any two are alike; and each foundry, in bidding for the supply of such pipe, makes the price to cover the conditions' required. I, therefore, have the honor of offering to the Institute a form of specifications for cast-iron coated water-pipe, that may be found useful to water-works companies and others requiring pipe of this kind. The conditions are all reasonable, and can be carried out by makers without additional cost, and with advantage to the purchaser. Section 1 gives the kind of pipe, with its general characteristics. Section 2 specifies that neutral pig-iron shall be used, since such iron possesses the strength required, and is uniform in its shrinkage. Section 5, requiring makers to give the brands of pig-iron used

Jan 1, 1890

By Howard Smith

FOR several years this Institute has recorded in its TRANSACTIONS the various discoveries of potash? in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons with an equivalent of 144,342 tons of pure potash.

Jan 1, 1936

By Theron Wasson

The state of Michigan showed considerable activity during 1935. The center of greatest interest was the Crystal field, which was unknown until March, 1935, and is an illustration of the effect of the unknown and unexpected on Michigan oil development. The fields of the state (Fig. 1) produced a total of 15,770,000 bbl. of oil in 1935, or about 5 million more than in 1934. In order to keep up this production 307 new oil wells were drilled, of which 88 were in the Crystal area, which produced 3,600,000 bbl. This field had a rapid development and reached its peak in October. Since that time increasing water encroachment has caused a rapid decline. The pay horizon at the top of the Monroe dolomite is only a few feet thick. Big producers were offset by dry holes or small wells. The discovery well, which was in section 11, Crystal township, Montcalm County, was drilled March 28, 1935. Its initial production was 5000 bbl. per day, and up to Dec. 31, 1935, had produced 350,000 bbl. of oil—dose to one-tenth of the total production of the field to that date. The Beaverton field, which was discovered at the close of 1934, did not develop rapidly. Four small producers were finished in the Dundee lime during the year. West Branch was active and at the end of the year had 97 producers, 72 of which were drilled during 1935. Most of the wells produce from the Dundee lime; a few are finished in the Traverse. The Birch Run field deserves special mention, for it is the one area where consistent production continues to be found in the Berea sand at about 1500 ft. Wells are small, 20 now producing a total of about 300 bbl. per day of oil of fine quality. The old Central Michigan producing area, extending from Nit,. Pleasant through Yost to Porter, continued to be the principal producing area of the state and accounted for 10,370,000 bbl. from 660 producing wells. Ninety-three new wells were drilled in this territory. The Porter field, at the southeast end of this producing trend, was outstanding from the standpoint of production. The old Leaton field of Isabella County added several new producers. Its production was greater than in 1934.

Jan 1, 1936

OFFICIAL INSTITUTE REPORTS FOR THE YEAR 1924 Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Directors of the A -I M. E, through their monthly meetings, a report of the year's progress is almost superfluous To the members who read the monthly reports of the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh infor¬mation, yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come The beginning of 1924 was not propitious for the members of the mining profession, though tonnage, production for 1923 had been high and the gross value higher than for several years The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed or were working in other industries Toward the end of the year, higher metal prices were in sight Old-time optimism began to grow, and it now brightens the outlook for 1925 An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing The number of new members joining has remained about as it was in 1922 and 1923 The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute

Jan 1, 1923

By A. Beeby Thompson

ALTHOUGH the exclusion of foreigners and private owners from participation in the development of the Russian oil fields prevents first-hand information being obtained, both official and private news indicate a growing appreciation of the value of the country's oil resources. Notwithstanding the suppression of that initiative and energy which only ambition can adequately stimulate, the industry is progressing and exports of products are assuming an importance that cannot be disregarded as an economic factor in the world's oil business. The following notes and observations must be regarded mainly as the views of one who has closely followed the fortunes of Russian oil, when considering the changes that have taken place in geological knowledge and oil-field technique, which have so profoundly modified oil-fields methods. Russia is fortunate in having retained the services of a few scientists and technologists whose devotion to science has superseded their personal inclination, and to these few men must be attributed the slow, but nevertheless striking, progress that has been made. The productive oil fields of Russia are centered around the Caspian Sea which, with its connected river system, constitutes such an ideal means of internal distribution for products. From the group of oil fields of which the city of Baku forms a center, oil is pumped to Black town, a suburb of Baku, where all the refineries are situated. The next important group of oil fields is located in the Terek district near Grosny, where refineries are erected and the products are piped or carried by tank cars to Petrovsk for the internal Russian market, or sent to the Black Sea by rail. A third oil field is spread over the province of Uralsk, north of the Caspian Sea, the main port of outlet being Gourief, at the mouth of the River Ural. In Trans-Caspia there are two oil-field centers, one near. Krasnovodsk on Chelekan Island, and one in Central Asia at Ferghana. The product of the former fields is transported to Baku for treatment, while the output of the Turkestan field is refined and consumed locally, mainly by the railway.

Jan 3, 1925