Search Documents

By J. H. Frye, C. P. Sun

A PRIMARY substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver aneys.1-5 It has been shown that at least, four factors are involved: (I) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2.4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. CALCULATION OF RATES OF WORK- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By R. E. Zimmerman

WITH coal-preparation plants becoming more complex and containing widely diversified types of equipment and processes, it is necessary that considerable control be exercised in their operation. Rising mine costs make it imperative that close check be made of plant efficiencies to assure a minimum loss of coal to the refuse bank. Further, much of the coal sold today is sold on a competitive specification basis, and this makes it necessary to provide frequent analyses and inspections. Many ' plants are required to operate on a two or three-shift basis, and as a con- sequence an efficient organization is required to eliminate down time and provide for smooth low-cost operation. ORGANIZATION Probably the most important item for successful operation of a preparation plant is a capable, properly organized staff, with the individual workers properly informed and well trained for their particular jobs, clear-cut lines of authority among the supervisors and in general a standard operating procedure for most conceivable conditions that may occur. The idea of placing the older, partially disabled and generally incompetent coal miner in the cleaning plant, as was the practice on the earlier tipples, is entirely inadequate in a modern complex cleaning plant. The new plants require intelligent, alert, and reasonably educated men. With perhaps millions of dollars invested in an installation, it is poor business to use other than a well organized, well trained, and properly supervised force. Organizations naturally must vary with the size of the plant and local conditions; whether it is a central cleaning plant at a distance from the mine organization or one of several cleaning plants operated by the company. Smaller operations can be operated by a washery foreman, under the supervision of the mine superintendent or perhaps the "outside" superintendent. Large installations should have a plant superintendent either responsible to the mine superintendent or preferably, where possible, responsible to a preparation manager or engineer. A typical organization chart for companies operating in the anthracite region of Pennsylvania is shown in Fig. 1. Breaker (preparation plant)

Jan 1, 1950

By V. R. Garfias

. EVEN before the arrival of Cortes in 1519, the history of Mexico was closely linked to that of its mineral production; the mining activities of the Aztecs being thus described by Clavigero, one of the early historians: In the mountains of Anahuac there abound in veins all kinds of metals, and infinite variety of other fossiliferous products. The Aztecs obtained gold from the countries of the Cohuijques, of the Mixtecas, of the Zapotecas and from various other places. They gathered that precious metal usually in grain, from the sands of the rivers, keeping a certain portion for the crown. They obtained silver from the mines of Taxco, of Tzumpango and others; however, this metal was not as esteemed by them as by other neighboring nations. They had two kinds of copper; one hard, which they used instead of iron to make sickles; lances and all kinds of rural and military instru-ments and another, soft, with which they made kettles, goblets and other receptacles. This metal abounds mainly in the province of Zacatula and in that of Cohuijques, which at present is in the kingdom of Michoacan. They obtained tin from the mines of Taxco and lead from those of Izmiquilpan, located in the country of the Otomies. From the tin they made money, and the lead, we know they sold in the market places, but we ignore the uses to which they applied it. They also had mines of iron in Tlaxcala, in Taxco and in other places; but they either had not discovered them, or did not know how to make use of the metal they contained. In Chilapa there were mines of mercury, and in other places there were mines of sulphur, alum, vitriol, cinnabar, cohre and of a white earth which they esteemed highly. As regards mercury and vitriol, we do not know of what use (they were to them; the other metals they used in paintings and dyes. There were then great abundance of amber and asphalt-bitu-men of Judea-on the coast of the seas and many cities of that territory paid tribute of one and the other to the kingdom of Mexico. They mounted the amber in gold, and it was only used as ornament and display by them. With the asphalt they made certain perfumes.

Jan 1, 1937

By Ezequiel Ordonez

The great activity with which the oil resources of the northern Cantons of the State of Veracruz have been developed has largely resulted from the great success obtained by the important explorations carried out since 1902 in the Ebano district in the North, and several years later near Tuxpam, in the South. It must not be thought that these successes were quickly obtained, since the preliminary studies by good experts, the acquisition of what were thought to be the most promising coast lands, the extensive clearing thereof, and finally the number of unsuccessful drillings at great depth, signified an original outlay of some tens of millions of dollars before finding commercial oil. The discovery of oil in industrial quantities at Cerro de la Pez, Ebano district, and the famous Dos Bocas gusher some years later, which was burned, once and for all made famous the Veracruz coast, where today is concentrated the Mexican output of mineral oil. In 1917, this production was nearly 61,000,000 bbl. It is well known that this output represents only a fraction of what the wells in actual production can furnish, because with adequate means of transportation and storage, the present extraction could be somewhat over 300,000,000 bbl. a year. These enormous potential oil resources of the Veracruz coast proceed from a relatively small number of wells, scattered over a few oil fields, separated from each other by large unexplored areas, wherein may be found other favorable fields which, in time, will undoubtedly become just as great centers of oil production. Experts who know our Gulf Coast believe that lands with commercial oil resources lie not only between the Pgnuco and Tuxpan Rivers, but that indications are that the oil zone of Mexico, with more or less interruption, takes in the coast zone from Northern Tamaulipas to the foot of the Sierra Madre of Chiapas, and the banks of the Usumacinta River. This generalization is not merely the outcome of optimism, but is the result of the persistency with which one finds, throughout this Gulf Coast, the most usual characteristics upon which we depend for recognizing oil-bearing lands.

Jan 1, 1920

By Lyall Zickrick

NUMEROUS brands of virgin pig lead are used in the manufacture of lead and lead-alloy cable sheath for commercial cables. In changing from one brand of pig lead to another a readjustment of press operating conditions is nearly always necessary. This is due largely to different flow characteristics, and some brands extrude at a much lower pressure than others; for example, copper-bearing lead requires much more pressure than a low-bismuth lead under the same operating conditions. With the modern type of lead press the extrusion practice in general differs very little. Molten lead at a temperature of 375° to 400° C. (710° to 750° F.) is cast in a water-cooled cylinder and allowed to cool or solidify into a slug for six to nine minutes. . This slug is forced into the die block and around the core tube through which the cable runs. The die block is held at an optimum temperature by means of gas flames, usually 175° to 225° C. (350° to 4.35° F.). Measurements of the tem¬perature of the cable sheath taken at the time of extrusion have covered a range of 190° to 225° C. (375° to 435° F.). According to Tammann, the rate of extrusion for a metal under constant pressure through a simple orifice is almost doubled for each 10° C. rise in temperature. Because of the irregularity of die-block construction, such a great increase is not obtained in lead-cable extrusion practice. To obtain more" definite information about the effect of small per¬centages of metals usually present as impurities in virgin pig lead, a series of compression tests were made covering several different brands of lead and various alloys. Since the usual temperature of the sheath is approxi¬mately 200.° C. as it emerges from the die block, these compression tests were all performed at 200° C. Five different brands of virgin pig lead were selected, as follows: Brand A: A desilverized western lead of very high purity. This lead contains neither copper nor bismuth. Brand B: A bismuth-free southeastern Missouri lead, usually con¬taining 0.05 to 0.08 per cent copper. Brand C: A copper-free mid-western desilverized lead of very good grade, usually containing around 0.06 to 0.10 per cent bismuth.

Jan 1, 1932

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935

Secondary blast holes are now being pierced in quartzite and sandstone quarries, using multiple hand-operated Jet-Piercing units supplied with oxygen, fuel and water from a compact mobile carrier. A unit of this type, operating in a Canadian quarry, enabled four Jet-Piercing blowpipes to pierce blast holes for two hours without shutdown. The piercing blowpipes used were developed by Linde Air Products Co., a division of Union Carbide and Carbon Corp. The mobile supply carrier was constructed by the quarry from specifications supplied by Linde and modified by the quarry operators for their particular use. Employment of the new self-contained unit, which allows up to four operators to pierce approximately 450 ft of blast hole without shutdown, accelerates rock removal operations. Normally, only two blowpipes are in operation at one time. Large boulders or ledges, which sometimes remain after primary blasting to hamper loading operations, can, in the case of certain hard rock, be prepared for reduction more rapidly with these new units than by any other means. A special feature of the new manual Jet-Piercing unit is the mobile gas and fluid supply carrier. It consists of a standard truck chassis fitted out with four banks of large standard-capacity oxygen cylinders, a steel-holding tank for fuel oil, and a gasoline-driven air compressor and tank for pressurizing the fuel oil tank. Cooling water for the blowpipes is supplied to the unit from a hose extension to the quarry supply line. Feeder lines from the oxygen cylinder manifolds and the oil and water tanks terminate in four sets of take-off stations on the control panel at the rear of the truck. As many as four hand Jet-Piercing blowpipes can be connected to the take-off panel by high-pressure rubber hoses. The hand Jet-Piercing blowpipe used with the mobile supply carrier is a highly portable device which can be manipulated comfortably by one operator. The blowpipe can pierce blast holes at rates up to 60 ft per hour, depending on the properties of the rock. Blast holes can be pierced at any angle from the vertical to the horizontal, making it necessary for the operator to drill from the top of the boulder. Hole diameter is held to approximately that which allows the use of a standard 11/8-in. diameter dynamite. The manual Jet-Piercing blowpipe has these important design features: a burner from which the combustion gases emerge at supersonic speeds (in excess of 6000 ft per sec); a hole-sizing shell which controls the minimum size of the hole and protects the copper burner; and a sliding shield which protects the operator against the steam and spallings ejected from the hole during the piercing. The Jet piercing process has been applied successfully in United States and Canadian quarries within the last several years as an advanced method of "drilling" blast holes.

Jan 1, 1952

By Albert E. Reed

THE development of the modern high-speed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1945

By J. Edgar Pew

As MOST of the oil production comes from leased-lands and not fee property, I shall refer to "leases" as covering the producing tracts. To produce oil, leases on land must first be obtained. Well-selected leases are all important. Not many years ago, the location for drilling for oil in wildcat territory was too frequently determined by the nearness, of adequate water and fuel supply, or with a view to cheapness of transportation. To some extent, the "creekology" theory is the result of the number of wildcat tests made near streams, to obtain water for operations. Now, an up-to-date operator will depend on his geologists for his location and, in many cases, will spend thousands of dollars to get water to it. The wisdom of following the geologist rather than the creek has been abundantly demonstrated in the past few years. In vast territories, where dry holes are spotted at intervals of a few miles or less. apart, and by reason of which these territories have been condemned for oil, the geologist is now finding many more spots that are producing large quantities of oil. No better tribute to the work of the geologist can be found than the surface and subsurface work being done in practically all parts of Oklahoma and the development had as a result of this, work. A land department is usually organized by placing in charge a man who is not only acquainted with the oil development, but who is a shrewd buyer, a first requisite for which should be unquestioned integrity. It takes a shrewd buyer to resist the persuasive lease broker, frequently backed by a geological picture from which the oil fairly drips. The geologist can help a lot by being absolutely honest when he makes these pictures; he will also thus strengthen his own cause. A geologist should interpret his own work and put his name behind his interpretation. If he does not he is liable to be misquoted and often discredited, as a result, by some overzealous lease broker giving an interpretation never intended by the geologist.

Jan 8, 1925

By R. Scot Clark

The reactively sputtered silicon dioxide capacitor -was developed for use in the monolithic integrated circuit, thereby requiring the capacitor to be fabricated on an oxidized silicon slice. The silicon dioxide film is formed by reactively sputtering silicon in a 50 pct Ar-50 pct 0, atmosphere and the physical properties are indistinguishable from silica. A practical upper limit of capacitance per unit area of 0.25 pf per sq mil is reached with the capacitors fabricated from the Si0, film. Methods shown to enhance this value are double stacking the thin-film capacitors and addition of aluminum to the silicon cathode during sputtering to form an aluminosilicate dielectric. A major contribution to the field of diffused integrated circuits would be the addition of auxiliary passive devices for replacement of diffused passive devices which are currently being fabricated for many integrated circuits. This accomplishment would increase the flexibility of the diffusion process in order to concentrate more on transistor parameters rather than on fabricating diffused resistors and capacitors. To pursue this technique, a thin-film SiOz capacitor was developed which has _ proven applicable to many integrated circuits. Although the SiOl capacitor has an application, the major deterrent from extending the integrated circuit into many useful areas such as low-frequency linear application is the low dielectric constant of SiO, and the low usable capacitance in an integrated circuit. This paper will cover the sputtering techniques used for forming the SiO, film, the physical and electrical properties of sputtered SiO,, and yield information concerning the application of these capacitors to integrated circuits. REACTIVE SPUTTERING Reactive sputtering is simply the sputtering of a metal or semiconductor in glow discharge in the presence of a reactive gas. The material to be sputtered is seen in Fig. 1 as the cathode of the system and is bombarded with positively charged ions of the ambient gas. In this investigation, the ambient gas is composed of 50 pct Ar and 50 pct O2 at a pressure of approximately 2.5 X l0-' Torr. The ions are accelerated toward the cathode in the cathode dark space by the electric field and upon striking the cathode effect a momentum energy transfer to the surface atoms. The transferred energy is sufficient to dislodge a surface atom or atoms and these particles diffuse through the glow discharge to the collector or anode. Several mechanisms of oxidation in the reaction chamber can be considered during reactive sputtering. 1) The surface of the cathode is oxidized and the oxide is subsequently sputtered. 2) Oxidation and sputtering occur simultaneously. 3) Sputtering of the cathode material is followed

Jan 1, 1965

By A. K. Knickerbocker

Practically all underground work on the Minnesota iron ranges is done by miners working on a so-called contract wage system. This system, while it has certain advantages over the straight day's pay or company-account method of wage payment, has serious and vital defects. In view of the scarcity and demands of labor, it is important that employers of labor scrutinize their systems of wage payments carefully, not only to save losses and trouble, due to labor disturbances, but also to secure the greatest efficiency of their workmen and reduce their operating costs. It is admitted that an adequate, just, and equitable wage is the prime factor in bringing about these benefits. The wage of labor and its method of application and payment have been, and always will be, the main factors in the unrest and dissatis. faction of labor. Not only does labor want and need an adequate wage, assuming that work is adequately performed, but it wants and is entitled to a just and equitable wage. Labor must have respect for the fairness of the wage and for the fairness of the management in the application of the wage It is conceded that the Minnesota iron miners are now, and have been, in the main paid adequately, but the inherent defects of the so-called contract system prevent any just or equitable application of this wage to the various units of the labor body. The defects of the contract system, with its obvious inequalities, favoritisms, and injustices, are cancers in the brain of labor. Every thinking miner realizes these defects and knows just what they are; the unthinking do not realize the details of the subject, but each month they are forcibly reminded of these defects through the pay envelope. As practiced on the iron ranges, however, the so-called "contract " system is not a contract and the name is a misnomer. No true contractual obligation exists. As usually practised, the contract system involves the setting of a price per foot in development work, or per foot or per car, usually the latter, in slicing or stoping, by the mining captain, and assumes its acceptance, though often under protest, by the men. A price is set for each working place, in which there are usually two men per shift. This price includes labor and supplies, such as explosives, fuse and caps, shovels, carbide, etc., and the men divide the total earnings less the amount expended for supplies. The cost of the supplies charged to the men varies

Jan 1, 1920

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By D. R. Spink

In the preparation of zirconium and hafnium metals, there are many indications that impurity levels control the physical and chemical properties of the metal. The purpose of this work was to develop methods of producing pure raw materials that could be reduced to highly pure metals. Early work by the Carbomcndum Metals Co. and others indicated that certain fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. We have developed workable fused salts along with a continuous and higly efficient scrubber design which can be used to produce very pure zirconium tetrachloride. Metal made from the purified tetrachloride has been shown to approach crystal bar metal in purity. Scrubber designs are discussed with recommended materials of construction. VARIOUS methods have been used to purify zirconium (and hafnium) tetrachloride. Most of these methods involve thermal degassing initially (the removal of more volatile compounds at temperatures below that where zirconium tetrachloride exhibits a significant vapor pressure) followed by a sublimation step (which conveniently leaves the nonvolatiles behind.) While these procedures effect definite purification, such processing is batchwise and does not result in optimum purification. Early work by The Carborundum Metals Co. and others indicated that fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. The objective of this work was to develop a continuous fused-salt scrubbing process that would yield high-purity zirconium and hafnium tetrachlorides. The term "fused salt" refers to the molten state of ionic compounds and as used here, specifically refers to alkali metal and alkaline earth halides. Fused salts, because of their many valuable properties, are becoming increasingly im- portant industrially. These valuable properties of the fused salts are: 1) stability at elevated temperatures; 2)low vapor pressure; 3) low viscosity; 4) ability to dissolve many different materials; and 5) good elctctrical conductivity. All but the last property enhances the use of fused salts as scrubbing agents for zirconium and hafnium tetrachlorides. Fused-salt scrubbing may be defined for our purpose as the intimate contact between a gaseous compound and a molten salt with the purpose of removing impurities from the gaseous compound. In this case, the gaseous compound is zirconium tetrachloride which submlimes at 331°C. When this gas is contacted with a molten salt, impurities such as aluminum, iron, and titanium are removed and the resulting product is considered fused-salt scrubbed. Zirconium and hafnium are sold to a purity specification. Generally speaking, normal production without scrubbing is capable of meeting specifications. There are, however, several considerations That make the knowledge of methods of additional purification highly desirable. These are: 1) the control of product analysis; 2) the production of a pure product for special applications; 3) the salvaging of off-specification material; and 4) the use of raw materials with higher impurity levels than 1 he present raw materials. You will note that items 1 and 2 are somewhat complementary to each other and that item 4 assumes that The present process has impurity removal limitations. To better understand the part that fused-salt scrubbing of zirconium tetrachloride plays in the manufacture of zirconium, Fig. 1 contains an illustrated flow sheet of the industrial production of zirconium metal. In referring to Fig. 1, we can point out the specific benefits derived from our ability to purify zirconium tetrachloride. Purification of the crude (hafnium-containing) zirconium

Jan 1, 1962

By J. J. Scott

This investigation utilizes three dimensional photo-elastic techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by observation of points in slices from the model with a polariscope and solving the data thus obtained by the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. The results of this work provide information on the overall stress distribution in points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type. Underground excavations disturb the equilibrium of the earth's crust and a core of fracture, or altered stress distributions exists around the openings. This fact is well known by mining operators and investigators in the rock mechanics field. Analysis of the stress distribution in the areas around mine workings is a most difficult problem and one which has no simple and direct solution. Some of the approaches used by investigators in attempts to study stress distribution around mine openings involve mathematical analysis, photoelastic techniques, statistical analysis, model studies on brittle materials and observation of fracture patterns. Models involving imbedded strain gauges, gelatin models using imbedded strings to show internal movement, and many other unique laboratory techniques are employed. Work is also being done in mining operations where load cells, strain gauges, photostress material, convergence plugs, dynamic plugs, etc., are used to measure strain which can in turn be used to obtain stress. Some of these devices measure strain from which stress may be derived. All approaches to the solution of stress distribution are hampered by the fact that the earth is not a homogeneous, isotropic and elastic media. Geologic faults, fractures, bedding planes, vugs, variations in material composition, variations in grain size and structure, etc., make it extremely difficult to obtain results which can be universally applied to mining operations. The purpose of this investigation will be to demonstrate the use of three-dimensional photoelastic techniques to obtain the stress distribution in the pillars and roof of a room and pillar mining operation. This method utilizes full analysis of interior points, and thus it may be that small tensile or shear stresses found in the investigation will prove to be of greater significance than the more obvious points of stress concentration found by two-dimensional techniques. A digital computer was employed to simplify and to shorten the time necessary to obtain final results. Application of the computer to problems of this type may enable future investigators to attempt more elaborate analyses than have been previously considered feasible. THEORY Three Dimensional Stress Analysis-Shear Difference Solution:' Photoelastic studies are based on the fact that an optically isotropic transparent solid becomes optically anisotropic when subjected to forced deformation; the degree of optical anisotropy being proportional to the deformation of the material. There are two fundamental laws which govern photoelasticity: 1) Light is polarized in the directions of the principal stress axes, and is transmitted only on planes of principal stress. 2) The difference in principal stresses is proportional to the difference in the indices of refraction along the planes of principal stress. One method used in three-dimensional photoelastic work is to examine a slice of the object by normal incidence and oblique incidence. In normal incidence,

Jan 1, 1964

By R. V. Smith, M. H. Cullender

Rigorous equations for calculating subsurface pres.tures in flowing and static gas wells, and pressures along horizontal pipelines are presented in this paper. These general equations, based on the mechanical encrgy balance, contain no assumptions regarding temperature and can be used with either straight-line or curved temperature gradients. The friction factors recommended in this report are based on an absolute roughness of 0.0006 in. Flow is always considered to he turbulent. Although these general flow equations are solved by numerical means, the methods are as convenient as many of those used today to calculate pressures in gas wells and pipelines. These numerical methods are illustrated for flowing and static columns of gas in wells and for flow in pipelines. The authors believe that the use of these methods will result in more accurately calculated pressures in gas wells and pipelines and that [he methods are more flexible than any in use at the present time. Also, the methods are easily adaptable to automatic computers. INTRODUCTION The problem of calculating subsurface pressures in gas wells and along flowing pipelines has been studied by many investigators with the results that two widely-used methods have been presented in technical literature. One approximates conditions in a gas well or pipeline by assuming that temperature and compressi- bility are constants tor the entire gas column. The other method assumes that temperature is constant at some average value but permits compressibility to vary with pressure at the constant temperature. While these approximations may be justified for relatively shallow and low-pressure wells, they become more and more unrealistic as the calculations are applied to the deeper high-pressure wells. In wells or pipelines where there is an appreciable change in temperature between the inlet and outlet ends of the flow string, it is equally as important to consider the change in compressibility with temperature as it is to consider the change with pressure. Consequently, the methods presented in this paper were developed to provide a workable procedure for calculating pressures in gas wells and pipelines which makes no assumptions regarding either temperature or compressibility. The friction factors recommended for use with the equations were the result of study of published literature and extensive experimental work with gas wells. The F,. values in Appendix IV which contain the friction factor are equivalent to an absolute roughness of 0.0006 in. as calculated by the Nikuradse equation. The absolute roughness of 0.0006 in. was previously published by Cullender and Binckley2 for gas wells; it is in agreement with 0.00065 in. of Smith, Dewees, and Williams1 for gas wells and 0.00065 in. of Baker and Swerdloff4 for pipelines; it is in reasonable agreement with 0.0007 in. reported by the Bureau of Mines and the American Gas Assn.5 for large transmission lines. However, any type of friction factors may be used in the equations by a change in the F, values in Appendix [V].

Jan 1, 1957

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By J. D. Testerman

A statistical technique to identify and describe naturally occurring zones in a reservoir and to correlate these zones from well to well is described. The technique is particularly useful in describing a reservoir where cross flow between adjacent strata is important in determining reservoir behavior. Although it has been used primarily for permeability zonation, the technique is general and can be used to correlate any reservoir property or related data, such as the information contained in well logs. INTRODUCTION One of the first problems encountered by the reservoir engineer in predicting or interpreting fluid displacement behavior during secondary recovery processes is that of organizing and using the large amount of data available from core analysis. Permeabilities pose particular problems in organization because they usually vary by more than an order of magnitude between different strata. Due to the sheer volume, it is almost always necessary to group data and to use an average value to represent a number of measurements. Perhaps the most common method now used to group permeability data is the capacity-fraction technique, which ranks permeabilities in order of magnitude, regardless of the physical location of the permeabilities within the reservoir. The cumulative per cent capacity is plotted against cumulative per cent thickness. This plot is divided into an arbitrary number of zones, generally of equal thickness. Five zones (or averaged groups of data) usually are obtained, each of which is treated as homogeneous in subsequent calculations. The division so obtained has no physical meaning; strata in the same zone, calculation-wise, are usually not adjacent in the reservoir. Reservoir engineering techniques being developed will handle crossflow that occurs between adjacent communicating reservoir strata because of imbibition and gravity segregation. Since crossflow occurs between physically adjacent layers within the reservoir, a new zonation technique recognizing the actual location of strata within the reservoir is necessary. Similarly, the recognition of natural zones is important for predictions of oil recovery by processes involving diffusion. One such process is miscible displacement, where predictions of lateral diffusion within the reservoir must recognize the actual location of the invaded zones in relation to the rest of the formation. Natural zones must also be adequately recognized to account for heat transfer within the reservoir during thermal exploitation. Because of the complexity of the problem, statistics appear to offer the only practical hope of dividing a reservoir into physically-meaningful natural zones. This paper presents a statistical technique for identifying these natural zones and for ascertaining which ones are likely to be continuous between adjacent wells. The zones defined have minimum variation of permeability internally and a maximum variation between zones. The technique is general and can thus be applied to reservoir properties other than permeability. The method will guide the reservoir engineer in estimating which zones are likely to be continuous between wells. However, a statistical correlation based on permeabilities in two different wells is no guarantee that the zones so defined are, in fact, continuous. Rather, the assumption of continuity must be consistent with geological data concerning the depositional environment, as well as justified on the basis of engineering judgment in combination with statistics, just as judgment is required with conventional zonation methods. CALCULATION PROCEDURE The reservoir zonation technique is a two-step operation. The steps are individually described, and a sample calculation is presented in the Appendix. ZONATION OF INDIVIDUAL WELLS First, the set of permeability data at a single well is zone, into Zones. These zones are selected so that variation is minimized within the zones and maximized between the zones. The equations4,6 used to zone the data are where B = the variance between zones, , = the number of zones, i = the summation index for the number of zones, j = the Sumation index for the number of data within the zone, mi = the number of data in the ith zone, k,. = the mean of the permeability data in the ith zone, k . = the over-all mean of the data in the well, W = the pooled variance within zones, N = the total number of

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many localities.1-3 As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermo-electric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the. pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1-the validity of the calibration of the pyrite geothermometer; and 2-the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating, pyrite geothermometer temperatures and thermo-electric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermo-electric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1952

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953