Search Documents

The Fifth Annual National Exposition of Chemical Industries will be held in Chicago at the Coliseum and First Regiment Armory during the week of Sept. 22. It was decided to hold the exposition in Chicago, this year, for two reasons: The U. S. Army commandeered the Grand Central Palace Exposition Building in New York, immediately on the close of the last exposition and converted it into a receiving hospital, the use for which is now, happily, nearly ceased; and it was thought that the Exposition would succeed in bringing about a greater development of chemical industries in the Chicago district and the adjoining states. The Advisory Committee of the Exposition consists of: Charles H. Herty, Chairman, Editor Journal of Industrial and Engineering Chemistry; Raymond F. Bacon, Director, Mellon Institute; L. H. Baekeland, Member Naval Consulting Board; W. D. Bancroft, President, American Electrochemical Society; Henry B. Faber, Industrial Filtration Corpn.; Ellwood Hendrick, President, The Chemists' Club; Bernard C. Hesse, Chemist, General Chemical Co.; A. D. Little, President, Arthur D. Little Inc.; Wm. H. Nichols, President, American Chemical Society; R. P. Perry, Vice-president, The Barrett Co.; H. C. Parmelee, Editor Chemical &; Metallurgical Engineering, G. W. Thompson, President, American Institute of Chemical Engineers; T. B. Wagner, Vice-president, U. S. Food Products Corpn.; M. C. Whitaker, President, U. S. Industrial Chemical Co.; and Charles F. Roth and Fred W. Payne. There is also added a special Chicago committee consisting of L. V. Redman, W. D. Richardson, A. V. H. Mory, Carl S. Minor, F. W. Willard, and Wm. Hoskins; the managers, as in the past, are Charles F. Roth and Fred W. Payne.

Jan 6, 1919

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank' standardized by the American Society for Testing Materials. Although this method of classification has been an American stand¬ard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1944

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By Joseph M. Locke

The discovery of this asphaltum was made by S. H. Gilson, of Salt Lake, and since then the material has borne the local name of Gilsonite. So far as I have been able to ascertain, however, the first published notice of this discovery was made by Prof. W. P. Blake in the Engineering arid Mining Journal, of December 26, 1885, where he names the new mineral Uintahite, from the place of its discovery, the Uintah Mountains in eastern Utah. The priority of publication and the geographical fitness of the name will probably secure its acceptance by mineralogists.* The following is Prof. Blake's article. In the month of September last, a sample of peculiar asphalt was received for examination, and recently when in Provo, Utah, I had the opportunity of seeing a considerable quantity brought in from the Uintah Mountains. It is obtained in masses several inches in diameter, and apparently free from mechanically disseminated impurities. It breaks with a conchoidal fracture, is very brittle, and is readily reduced to powder in a mortar. Hardness, 2 to 25. Gravity, 1.065 to 1.070. Color, black, brilliant, and lustrous; streak and powder, a rich brown. It is a non-conductor of electricity, and is electrically excited by friction.

Jan 1, 1888

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.' This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2'6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7'9 These effects were observed at testing temperatures in the range 100 to 300'. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.' These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180' was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio 'c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By J. R. Linney

APPROXIMATELY 5,788,000 long tons of crude ore was produced by the Eastern magnetite industry in 1946, or a drop of 26 per cent compared -with 1945. Decrease in production -throughout the industry varied from :8 per cent for the mine with the lowest reduction to 49 per cent for the mine -with the highest reduction. At the Chateaugay mine, operated by :the Republic Steel Corp. at Lyon Mountain, N. Y., 426,900 long tons of crude ,ore was produced, yielding 129,500 long tons of concentrates or a reduction of 46 per cent compared with the previous year. Owing to a strike the mine was closed down from Jan. 21 to July 29. At the Mineville mines, also operated by Republic Steel, output was 755,000 long tons of crude ore or a reduction of 49 per cent compared with 1945. The yield from the crude ore production consisted of 51,500 long tons of lump ore and 380,000 long tons of concentrates. The Mineville plant did not operate from March 17 through July 28, on account of the strike. The Fisher Hill mine, which produced 93,000 long tons of crude ore, included in the above figures, has not operated since March 17, 1946.

Jan 1, 1947

By Cyril Stanley Smith

THE art of metallography is mature and the forms in which various micro-constituents appear are well known. Investigations almost without end have disclosed the importance of the exact manner of distribution of phases on the physical properties and usefulness of an alloy. Surprisingly, however, relatively little attention has been paid to the forces that are responsible for the particular and varied spatial arrangements of grains and phases that are observed. Like the anatomist, the metallurgist has been more concerned with form and function than with origins. In this paper it is proposed to develop the simple concept that many microstructures result from an attempted approach to equilibrium between phase and grain interfaces whose surface tensions geometrically balance each other at the points and along the lines where they meet. From this follows a number of principles which may prove to be of interest to the metallographer and of practical use in explaining failures and in designing alloys for particular service. In general, the discussion will be limited to structures obtained after full annealing. The simple principles do not apply to structures resulting from Widmanstatten mechanisms in precipitation, or to other structures not in local equilibrium and in which lattice coherency is a determining factor. INTERFACIAL TENSION Much has been written by physical chemists about the free energy of surfaces, which manifests itself as a measurable surface tension. Two- and three-phase interfaces in fluids seek a condition of minimum energy and approach a geometrical configuration in which the various forces are in vectorial balance.* Measurement of the angles established between the interfaces when in equilibrium provides a quantitative value for the relative value of the surface forces involved. The case of two fluids meeting at the surface of a solid (of great importance in connection with the flotation of minerals) has often been studied, but there have been few investigations of the equally definite interface between two or more crystals of a single solid phase, or the more complex cases where crystal grains of more than one phase are involved. The principles are best illustrated by considering first the case of two and three immiscible liquids. If, as in Fig I, a liquid, 2, is dropped into a less dense liquid, I, it will form a sphere-if gravity and viscosity can be ignored-for in this shape the interface has the smallest possible area. If these two phases should together encounter a third phase in which they are both immiscible, the geometry will change to become that which gives the lowest total energy for all three interfaces. Thus, if the spherical drop of liquid, falling through r, eventually reaches the interface between liquids 3 and I (we are assuming that the density of 3 is greater than 2, and 2 than I), it will assume the shape of a lens, the angle

Jan 1, 1948

By Hans Lundberg

By electrical prospecting, orebodies that do not otherwise manifest themselves at the surface may be located. Conditions favorable to success with the methods are: Favorable geological conditions, such a proportion of minerals of good electrical conductivity in the orebody as will render the latter materially a better conductor than the enclosing rock, situation of the orebody within the range of influence of the electrical currents used and in proportion to this range a sufficient area of horizontal cross section of the orebody. The result is to permit of spotting drill holes accurately and to save the expense of drilling barren ground. THE art of prospecting, like other branches of mining, has developed rapidly during the last ten years, mainly because of the advancement of mining geology, but also because of the development of "geophysical methods," which are based on the different physical characters of minerals and rocks, e. g., specific gravity, elasticity, and magnetic and electric properties. These methods have proved of great value, especially in countries where the rock is covered by soil and direct geologic investigation is out of the question. In prospecting for orebodies, the methods based on studying differences in electrical conductivity have proved most successful; for which reason, the methods of electrical prospecting have been subject to the most energetic and systematic work, especially in Sweden. This paper gives a brief description of the methods of electrical prospecting now in use, especially the new electromagnetic methods, which have not been described before. The great differences in the electrical properties, especially in conductivity, between ore minerals and rock minerals are fundamental to all methods of electrical prospecting, for which reason, the electrical conductivity of ore minerals and rock minerals has been carefully studied in connection with and previous to the development of the various methods of prospecting with electricity. Ore minerals with a metallic luster, such as chalcopyrite, iron pyrite, galena, specular iron, magnetite, etc., also graphite and a number of cows, have considerably higher conductivity than the surrounding rock and soil (see Table 1). The figures of the table denote the specific resistance W, expressed in ohms for a cube with an edge of 1 centimeter.

Jan 7, 1925

By G. W. P. Rengstorff, L. E. Olds

High purity molybdenum ingots containing controlled amounts of a single impurity element (oxygen, nitrogen, or carbon) were prepared. These ingots were tested for ductility by bending test specimens at various temperatures. The relationship between the plastic behavior of the ingots and their chemical composition has been determined. MANY proposed applications for molybdenum require ductility at or near room temperature. At the present time, it is possible to obtain wrought molybdenum with considerable ductility only if special fabrication techniques are used to control the grain structure. Starting with are-cast or powder metallurgy ingots, the usual methods for obtaining ductility rely on fabrication procedures that result in fibered microstructures in the finished product. Recently, it has been found that the ductility of either powder metallurgy or are-cast molybdenum can be improved by uniform recrystallization of the metal to a very fine equiaxed grain structure.' The need for a fibered or a fine grained structure may limit the practical usefulness of molybdenum. For example, welding. which may be used in fabricating the metal, generally produces coarse grained structures that lead to brittleness. This applies, certainly, to currently available commercial molybdenum. Although commercial molybdenum is brittle when the grains are coarse, it has been shown experimentally that fine grained structures are not always essential for ductility. For instance, as-cast molybdenum with a coarse columnar grain structure is ductile if it is sufficiently pure.' Because high purity cast molybdenum has good ductility even when coarse grained, it is probable that the brittleness in coarse grained commercial molybdenum is caused by the impurity content of the metal. Although the general effects of impurities on the cold ductility of molybdenum have been known in a qualitative manner for some time, no quantitative evaluation of these effects has been available. The present investigation was made in order to determine more accurately the effects of oxygen, nitrogen, and carbon on the cold ductility of cast molybdenum. Oxygen has long been known to be detrimental to ductility, although the minimum amount which will embrittle molybdenum has been open to speculation. Parke and Ham" showed that ingots with oxygen contents above 0.003 pct could not be forged. Maringer and Schwope have described the embrittle-ment of molybdenum wire by oxygen. A discussion on the effects of heat treatment on the distribution of oxygen in molybdenum has been given by Perry, Spacil, and Wulff." Although nitrogen would also be expected to have harmful effects on ductility, no extensive work has been done previously to determine whether this is so. However, Tury and Krausz" found that wires presumably with less than 0.007 pct N were brittle. Carbon is added to commercial cast molybdenum for deoxidation. Parke and Ham" have shown that molybdenum containing as much as 0.06 pct C could be forged if the oxygen was kept below 0.003 pct. Also, Bruckart and others' found that the room temperature ductility of sintered molybdenum improved with carbon contents up to 0.84 pct. However, Rengstorff and Fischer' found that residual carbide particles in cast molybdenum apparently had an unfavorable effect on room temperature ductility.

Jan 1, 1957

By E. A. Anderson

In 1918 the American Society for Testing Materials held a symposium2 on what was then known as season cracking. The sessions included six papers, all on brass. During the ensuing 26 yr., many new workers have come into the field and several other metals have been found subject to failure by stress-corrosion cracking when the right combination of stress and environment is achieved. It is not surprising, therefore, that the present symposium has brought forth 29 papers covering alloys of seven important metals. The phenomenon of stress-corrosion cracking is not necessarily confined to these seven metals. Dix3 has stated, "Indeed, it is probable that ingenious investigators can find solutions which will stress-corrosion crack any known metal or alloy." Mears, Brown, and Dix4 have indicated that stress- corrosion cracking failures are not necessarily limited to metals but may include the plastics. It is to be expected that the increase in the number of metals known to crack in service and the general emphasis on such failures at a symposium such as this will alarm many to whom the subject is un- familiar. Such alarm is not justified by the record. It is true that stress-corrosion

Jan 1, 1945

Minute of the Board of Directors, Jan. 26, 1917 In the name of all the members of the American Institute of Mining Engineers, this Board extends to. Mr. Herbert C. Hoover, an honored Vice-President of the Institute, on the occasion of his present temporary return to his native land, the cordial welcome of his colleagues, and their congratulations upon the noble work splendidly done by the Commission for Relief in Belgium of which he is the head. It is understood that a leading purpose of Mr. Hoover's visit to America at this time is the collection of additional funds, to be administered by his Commission in the care of the destitute children of Belgium. To this enterprise endorsed by both the belligerent parties, as well as inspired by the purest and tenderest sentiments of humanity, contributions are solicited from engineers, especially through an organization known as the "Belgian Kiddies Limited," which this Board, heartily approving its object and method, recommends to the consideration of the members of the Institute. On motion duly seconded it was unanimously VOTED.-That this minute be spread upon the record of the Board, and published in the Bulletin, and that a copy thereof be transmitted to Mr. Hoover, and to the San Francisco Section of the Institute.

Jan 3, 1917

The Mineral Industry, Published by McGraw-Hill Book Co, New York, N Y. The Mineral Industry is an annual review of the mineral industry It is a standard and complete reference on the mineral industry for the year covered Through the cooperation of the A I M E its publication in 1933 was made possible Mineral Industry for 1930 contains sections devoted to the production, consumption, trade, market, uses and technology of the following headings: Abrasives, aluminum and bauxite, antimony, arsenic, asbestos (b), asphalt, barium and strontium, chromium (b), coal and coke, cobalt (b), copper, diatomite, fluorspar, gold and silver, graphite, gypsum, iron and steel (b), lead, magnesite, manganese, mica, molybdenum, nickel, petroleum and petroleum products, phosphate rock (b), platinum group metals (b), potash, precious and semiprecious stones (b), quicksilver, radium (b), uranium and vanadium, slate (b), sodium salts, sulfur, pyrite, sulfuric acid, talc and soapstone, tin, titanium and zirconium, tungsten (b), zinc, minor metals, minor nonmetals, ore dressing and coal washing (b). Sections marked (b) have appended a bibliography of recent literature on the subject. Each section is written by an acknowledged expert. Other volumes contain similar material Prices -The Mineral Industry, 1892-1930, vols. 1 to 39. Complete sets of this work, uniformly bound, except vols 25 and 26,

Jan 1, 1933

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

No. 264. A long established company operating steel and iron foundries, machine and forge shops, whose varied products are sold to the Government, railroads, mining and contracting industries, etc., has, openings in both manufacturing and selling departments for men with technical education and experience who are not subject to military call. State full particulars, kind of position preferred and salary expected. No. 265. Young man wanted, technical graduate preferred, to superintend construction f a small charcoal blast furnace. Man with blast-furnace experience preferred. For the right kind of man this is, not only a permanent job but an opportunity. In writing, give full particulars as to age, education, experience, salary wanted, etc. No. 26.6. An important copper mining and smelting company in Arizona needs two or three metallurgical chemists, at salaries. ranging front $150 to $175 per month. No. 267. A consulting mining engineer needs two superintendents for developing chrome deposits near Philadelphia; and another technical man for other engineering work in the same vicinity. No. 268. An iron-mining company, in New York State needs a mining engineer with knowledge of geology and acquaintance with construction work; A married man, with about 10 years' engineering experience preferred.

Jan 2, 1918

By E. S. Bumps, W. F. Craig, M. Baeyertz

Metallurgists have looked at fractures macroscopically for many years and have evolved a vocabulary in which such words as "cleavage," "brittle," "shear," "ductile," "granular," "fibrous," and "silky" are used to describe the appearance of the fractured surface; but the meaning of these words in terms of metal structure is not well established. Observations of the structural meaning of "brittle" and "ductile" fractures in plate steels have been made, notably, by Kramer and coworkers1 and by Tipper.2 Grossman3 has studied the fracture of tempered martensite and combinations of ferrite and martensite. Notwithstanding these and other less concerted attacks on the problem, present understanding of fracture rests more on assumptions and logic than on experiment. It is the purpose of this paper to add a little to the growing fund of experimental observations of the nature of fractures in steel. The particular fractures to be described were obtained in conventional impact testing of an ordinary structural steel shape. In impact tests of the Charpy type, the specimens fail in a characteristic manner that depends on the steel and the temperature of testing. With ordinary structural and many other steel products, an appropriate range of testing temperature will cause a considerable change in the energy absorbed before fracture. This change is known as the energy transition and is accompanied, more or less closely, by alteration in the appearance of the fracture. At testing temperatures below the transition, the terms "brittle," "cleavage," or "granular" are used to describe the fracture; above it, "ductile" or "shear" are often used. Within the transition, the fracture changes from "brittle" to "ductile" by a progression in appearance, wherein the "brittle" portion of the fracture becomes restricted to a smaller and smaller central area of the fracture, as the testing temperature is raised and the "ductile" type of fracture is approached. All this is well known to metallurgists. The specimens under consideration are of the conventional V-notch Charpy type. They were taken from a structural steel shape of the following analysis: C Mn P S Si 0.17 0.46 0.009 0.029 0.03 Both longitudinal and transverse specimens were tested and examined. Fig 1 shows the energy values plotted against testing temperatures in the usual way. The curves for both longitudinal and transverse specimens show an energy transition, although the maximum energy absorbed at testing temperatures above the transition is greater in the case of the longitudinal specimens. Fig 2 illustrates the changes in the macroscopic appearance of the fractures that are associated with the energy transitions shown in Fig 1. Macrographs of the fractured surfaces of the specimens have been identified with the fracture ratings at intervals on each fracture curve. The numerical fracture rating on the ordinate of Fig 2 indicates the percentage of the area of each fracture that was considered to be "brittle" on macroscopic observation. Such rating of the fracture type in impact tests is now customary in many laboratories. Hereafter the specimens will be identified by reference to Fig 2 as 90 pct "brittle," 80 pct "brittle," and so on, in accordance with this macroscopic evaluation of the appearance of the fractured surface. The discussion of the fractures is divided into three parts. The first two are concerned with the mode of fracture and its relation to general structural features. As the same metal-lographic features occur in both longi-

Jan 1, 1950

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896