Search Documents

By H. Sato, I. Matsuoka, T. Kawai, S. Hasebe

In a limestone mine, a large amount of slime is washed off in order to remove impurities such as clay minerals. A fine sized calcite is, consequently, wasted and freight for carring the slime to reclaim land is expensive. The separation of calcite from the slime has been investigated by the flotation process, using sodium oleate as a collector. A satisfactory flotation of calcite from the slime requires great amounts of sodium oleate, because sodium oleate is consumed by clay minerals. But, the amounts of sodium oleate required are reduced to half by adding suitable amounts of sodium silicate. After rougher and cleaner flotation, the concentrate containing more than 97% calcite is obtained with 70% recovery; thereby the amount of slime to be reclaimed is reduced to 40%.

Jan 1, 1976

By J. H. Anderson, G. A. Parks, B. K. Jindal

Both temperature and humidity are important variables in electrical separations. By independent control of temperature and water vapor pressure, it is shown that charge depends primarily upon relative humidity, not on temperature or water pressure alone. All the effects of temperature changes other than modification of humidity are apparently small. However, humidity control can be achieved through manipulation of the more tractable variable, temperature. Both temperature and humidity are important variables in electrical separations. Some of their effects have been described in general by Fraas1,2 and by Ralston.3 The influence of temperature and humidity may be considered a problem in industrial separations because humidity, especially, is not normally controlled, hence leads to unpredicted quality control problems. The problem is significant whether the separation is based on conductivity differences or on contact electrification. There is no doubt that water adsorbs from humid atmospheres onto mineral surfaces resulting in conductivity changes.'-8 An empirical relationship between conductivity and humidity is1.4-6,8 where a and b are constants peculiar to the substrate, and s and h are the conductivity and relative humidity respectively. Some authors have taken advantage of differences in a and b among minerals to make or propose electrodynamic separations in which h is the key control variable. Fraasl,2 reported that the charge developed on quartz and feldspar through contact with aluminum is sensitive to humidity, as illustrated schematically in Fig. 1. Lawver9 found that the charge developed by quartz on contact with several materials was tem-

Jan 1, 1967

By Joseph W. Leonard

The purpose of this paper is to review and discuss some of the less evident and sometimes neglected opportunities for progressive developments in coal research. While a great deal of both promotional and technical information flows from some areas of coal research, output deficiencies in other areas of activity have reached a magnitude where important developments have been, and will increasingly be, unfavorably affected. These areas mainly involve coal mining and preparation. Some recommendations for the intensification of effort in these areas follow: Coal Mining While a huge tonnage of in-the-ground coal is assured, the location and distribution of these tonnages are becoming less favorable. The easy-to-mine coal which is located in or near population centers has been, or is being, mined. The vigor with which the less accessible reserves are recovered by the mining industry depends largely on the condition of the coal market at the time of mining. Hence, during a buyer's market, the commercially oriented mining industry is compelled to mine the easier and less costly reserves. Conversely, during a seller's market, the need to rapidly expand production results in more difficult mining and higher cost coal as few obstacles are encountered in finding markets. Hence, a seller's market tends to enhance the recovery of reserves while a buyer's market does not. One reason for today's fuel supply problems is that the Nation has recently emerged from a long-term coal buyer's market which lasted from about 1950 to 1968. During that period, national policy caused severe production cutbacks which regretably drove the industry to mining only the more accessible and better quality reserves. Often in order to remain in business, many hundreds of millions of tons of more difficult to mine reserves were abandoned and lost behind caved areas. Many of these reserves are close to population areas and would not have been lost in a more stable economic climate. It is difficult to fully account for all the impacts that were caused by the great buyer's market of the 1950s and 1960s. Besides the obvious loss of reserves that were once considered national wealth, the mining of better reserves tended to produce a generation of technically optimistic mining people. Mining people frequently became accustomed to looking at nothing less than outstanding mining conditions as a result of the declining market. Many are now and have long since received a re-education in the other half of mining. Going from many years of mining accessible, select and easy-to-win reserves, to the crash-driving of development entries in reserves that were considered unworthy of mining during 50s and 60s, frequently results in a much higher rate of encounter with in-seam and out-of-seam rock as well as with coal-deficient areas or "washouts." Intensive entry driving activity and compulsory non-selective mining in sometimes lean reserves were brought on by the need to rapidly open up new supplies of coal. Working under these requirements presents a continuing reminder that much more needs to be known about the relatively esoteric art of planning the best direction for driving entries in order to insure that a more consistent and greater supply of coal is available during early mine development. All of the preceding discussion tends to point to a need for a better estimate of those reserves of coal that are likely to be mined in the future. Such estimates should not be limited to the compilation of the amount of coal in the ground; but, where possible, should also include information concerning the capability for producing this coal. After all, a coal seam of ample thickness may have a degree of thickness variability, undulation, bad roof or floor, so as to make what would otherwise appear to be an attractive mining condition untenable. Underlying the problem involving the feasibility of producing known reserves is the need to develop better methods for the characterization of coal seams and associated lithotypes, based on drill core data, once at area is selected for mining. Reserves and their characterization involve aspects of exploration technology that are frequently considered mature. The resulting technological deficiencies may be the main reason why coal exploration frequently does not end with core drilling of a property, as it should, but extends into the mining operation during the driving of development entries. When exploration is extended to the driving of development entries, the near absence of integrated decision-making theory involving mining, geology, mathematics, and economics becomes, once again, all too painfully apparent and frequently results in very costly rationalizations. Hence, by the formal initiation of a concentrated program to combine the cyclical effects of economics with geology and mining, more relevant estimates of reserve distribution, tonnages, and production capability should be forthcoming. Moreover, a similar formal effort is needed to develop a combination of the most advanced concepts of mathematics, geology, and mining to better "see" coal seams as a means to favorably implement many long-range decisions involving mine safety and productivity. Much more applied research needs to be done on coal mining systems for mining in thin seams and/or under bad roof. Current difficulties in both of these areas at recently opened coal mines should provide a sobering glimpse into the future. Full-scale applied research, sponsored by appropriate federal agencies, is urgently needed on a scheme involving a new combination of established mining and preparation elements. The scheme may include: (1) a continuous mining machine remotely operated by a miner stationed at some distance behind the machine using a cord attached control box; (2) hydraulic transport of coal through pipes from the mining machine to a coarse refuse removal grid, crusher, and then on to portable concentrating equipment; (3) the hydraulic transport of clean coal out of the mine in pipes to the surface for thermal dewatering, if neces-

Jan 1, 1974

By B. M. Larsen

AN increasing amount of attention is being paid to the possible influence of oxygen, in its several modes of occurrence in steel, upon some of the properties of the metal; but clearly investigations along this line are unlikely to yield significant results until reliable analytical methods for the determination of oxygen have been established. This paper presents some results of a study of an improved Ledebur method which aims to determine a definite portion of the oxygen; namely; that which presumably is present in diffusible form in the. solid steel. These more or less preliminary results lead us to believe that the oxygen so determined has some significance; their presentation at this time will, we hope, stimulate discussion of, and focus attention upon, certain rather neglected aspects of the problem. Considerable work has been done recently on methods of estimating inclusions and on the vacuum-fusion method for oxygen; with results which, however, are of somewhat questionable significance. It is commonly presumed that the oxygen in a bath of molten steel in a furnace is present partly as a separate phase consisting of suspended particles of oxides or silicates, partly in solution, the latter being probably the more important. Upon addition of a deoxidizer, it reacts with some portion of the dissolved oxygen and precipitates it as additional suspended particles; the oxygen not eliminated in this way, which remains in solution in the liquid steel, may be regarded indifferently either as dissolved oxygen or as dissolved FeO. When the steel is poured, some of the suspended particles rise towards the surface, others remain trapped in the finished steel, appearing as nonmetallic inclusions in amounts corresponding usually to about 0.01 to 0.03 per cent 02 in the steel. The dissolved oxygen may be partly eliminated as CO during freezing of the ingot, but some remains either in solution or in part precipitated as FeO. Finished steels may thus contain oxygen in several forms: (1) In non-metallic inclusions which are probably quite insoluble in the solid metal at all temperatures; (2) in solid solution which at lower temperatures may be supersaturated; (3) in FeO particles produced by relief of this

Jan 1, 1932

By Yoginder P. Chugh

Elastic and viscoelastic behavior of three rocks-Tennessee sandstone, Barre granite, and Indiana limestone-was studied experimentally under uniaxial tensile stress. Cylindrical specimens of these rocks, about 1.0 in. diam and 2.0 in. long, were subjected to incremental constant stress history under uniaxial tension. The stress was held constant for a period of 40 min at each stress level. During this period, longitudinal and transverse strains on specimens were continuously monitored. The straintime history at each stress level was analyzed for elastic and viscoelastic parameters of a generalized Burger model. The viscoelastic parameters under uniaxial tensile stress were compared with those under uniaxial compressive stress. The experimental setup, experimental procedure, analysis techniques, and more significant results are described. This limited research effort clearly indicates the importance of the mechanical behavior of geologic material under tensile stresses.

Jan 1, 1975

By Ronald W. Utley

INTRODUCTION The ''Do's and Don'ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO'S and Don'ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer's local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer's shop order number (after order placement) •Serial number (after manufacture) DO'S 8 DON'TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer's recommended typical foundation drawings. If substantial alteration to manufacturer's drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By Andrew A. Blair

THE increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

Jan 1, 1876

By B. W. Veal, B. S. Chandrasekhar

THE Laue method of orienting single crystals requires the use of tables of angles between crystal-lographic planes, and between zone axes. Such tables have been published for cubic crystals, and some rhombohedra12 and hexagonal3 crystals. A table of angles between planes in ß-tin has also been published;4 these angles refer to only low-index planes, and are not particularly helpful in the actual indexing of spots on a Laue photograph. Furthermore, it is often useful to know the angles between zones which share a common low-index plane. We have calculated such tables of angles for ß-tin and indium, both between planes in principal zones, and between zones passing through principal planes. The results are given in Tables I and 11. The standard formulas were used, with c/a = 0.54554 for 0-tin, and 1.07586 for indium.

Jan 1, 1962

By O. N. Carlson, H. A. Wilhelm, J. M. Dickinson

On the basis of microscopic studies, melting-point observations, and X-ray analyses, a phase diagram is proposed for the Cb-V system. A complete series of solid solutions is formed with a minimum in the solidus at 1810°C near 35 wt pct Cb. No compounds or intermediate phases were found in the system above 650°C. THERE is an ever increasing need for better structural metals and alloys for use in nuclear reactors. In addition to the normal properties of engineering structural materials, such as high temperature strength, resistance to corrosion, and fabric-abil~ty, the nuclear properties of the material must be considered. In a nuclear reactor it is important to conserve neutrons, so a material which removes these neutrons from the reaction excessively is considered to have unfavorable nuclear properties. In nuclear-reactor design the engineer must have nuclear as well as other data available on alloys in order to make a wise selection of materials. Due to the fact that many of the common structural materials have undesirable nuclear properties, it is vital that new alloys of metals having more favorable nuclear properties be investigated. Columbium and vanadium are both high melting metals, both exhibit resistance to chemical attack, and no great difficulty is encountered in fabricating them into desired shapes. With proper treatment both metals can be cold rolled extensively without failure. In addition they have desirable nuclear properties for certain types of reactors. Therefore, the alloys of columbium and vanadium should be of interest in the atomic energy program. Since an alloy-development program is enhanced by a knowledge of the phase equilibria of the components, this investigation was undertaken to establish the phase diagram for the Cb-V system. According to the Hume-Rothery rules for alloying,' the chemical similarity, crystal structure, and atomic-size factor are favorable for a complete series of solid solutions for this system. Both elements are in the same family of group V of the periodic table and thus are quite similar chemically. The crystal structures of columbium and vanadium are compatible for extensive solid solubility, since both have body-centered-cubic structures. The atomic diameters of columbium and vanadium are 2.85 and 2.62Å, respectively. This difference of slightly more than 8 pct is well within the 15 pct maximum difference allowed for extensive solid solubility. Experimental Procedures Source of Materials: Columbium powder and sheet trimmings were obtained from the Fansteel Metallurgical Corp. According to the manufacturer the metal contains less than 1 pct impurity. An analysis of the metal showed approximately 1800 ppm C in the powder while the sheet trimmings contained less than 500 ppm C. Spectrographic analysis showed minor amounts of Ca, Cr, Fe, Mn, Si, Ti, V, and Zr in both forms of the columbium. No commercial source of vanadium having the ductility and purity desired was available to the authors at the beginning of this investigation. As a result, all of the vanadium used in this study was prepared by the bomb reduction of vanadium pen-toxide with calcium employing the method reported by Long.' Yields of massive vanadium normally were about 80 pct. Chemical analysis of the vanadium prepared in this manner showed the presence of 200 to 500 ppm N and 800 to 1000 ppm C. Minor amounts of Ca, Fe, Mn, Si, Zr, Cr, and Cb were detected by spectrographic analysis. This vanadium metal was ductile and was cold rolled into 5 mil sheet. Annealing was not necessary during this rolling and the metal retained its cold-rolling characteristic after are-melting. Preparation of Alloys: The Cb-V alloys were prepared by melting pieces of vanadium sheet togethel-with columbium in the form of sheet or pellets of powder. The melting was carried out under argon in conventional arc-melting equipment employing a tungsten electrode and a water-cooled copper crucible. Each alloy was remelted three or four times, inverting the alloy after each melting in order to assure complete mixing. Alloys normally were obtained as round flat disks, weighed approximately 70 grams, and had roughly the shape of a disk 1 1/2 in. in diameter and 1/4 in. thick. Half of each alloy

Jan 1, 1955

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry's law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2'= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,' using Laitinen and Liu's' value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,' and the equations of Wagner and Werner,' the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O' and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies' have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

By John M. Dale

Sulfur has attractive features as a base material for coating systems. It melts at 246ºF and can be applied as a liquid above this temperature. Its melting point is just above the environmental stress level, 180°F, for most coatings and yet it is low enough to be easy to work with in comparison to many hot melt systems. The viscosity characteristics are such that sulfur lends itself to spray applications. The oxidation rate of sulfur in the atmosphere is very low and sulfur has outstanding chemical resistance characteristics, particularly in acid environments. One of the greatest potentials for these coatings appears to be in the protection of other materials. At one time, most acid tanks and pits were constructed with acid- proof brick and sulfur based mortars. This type of construction is much more expensive than sulfur based spray coatings. An attractive sulfur based coating composed of sulfur, talc, milled glass fibers and dicyclopentadiene,1 developed by the Institute for the Bureau of Mines has excellent acid assistance and can be used to protect concrete from acid attack.

Jan 10, 1973

By H. B. C. Nitze

In view of the extensive use of vanning-machines in this country, a brief comparison of the results obtained by the plain belt generally employed, and the corrugated belt which was introduced a few years ago, may be of interest. The data given below have been abstracted from a working-journal, and hence lack the precision, and also, in several desirable particulars, the detail, which would naturally have been secured in special experiments ; but they have the advantage of being working-figures, and are sufficient as the basis of a fair comparison between the two kinds of belt working on similar ores. The conditions under which the work was done were the following :

Jan 1, 1893

By William G. [Peryam], Bishop Ottey M., Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rock-surfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to P8.00 per ton, and from the property to San Fernando the rate is P16.00 per ton. The company pays the road toll, P1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

MARCEL R. DALY (communication to the Secretary?).-The fundamental disagreement between Eugene Coste and the writer proceeds essentially from the contradictory views they hold on the origin of petroleum. This difference cannot be bridged, nor can inorganic and organic theories be discussed here. The writer has suggested that the proper thing in such a case would be to agree to disagree. Coming to the detailed objections further presented by Mr. Coste, the writer feels that, in the main, they take their source in a wrong interpretation of the theory, and the writer is sometimes too generously invested with views that are not his own. 1. The only requirement for the theory is that the oil proceeding from organic remains be distributed in a water-laden sediment, and that this sediment be submitted to the increasing compression due to the continuous accumulation of superimposed strata, which would tend to squeeze out the liquid contents (p. 1152). This squeezing out would be further aided by the distortion of the strata (p. 1148, a). Nothing here makes impossible the slow formation of the oil, if this is considered necessary, as the piling up of the strata in the syncline would require by itself a protracted length of time, and, further, the squeezing-out process is a slow one. Possibly the formation of the oil may even continue during part of the process of distortion. But the mode of formation of the oil and the time and temperature required for it are left to the chemist to decide. The diastrophic theory, which is essentially a theory of motion and accumulation dependent on the laws of mechanics, is not directly concerned with them, provided the general points heretofore outlined be agreed upon. Perhaps it would be wise not to claim too many "eons" for the formation of the hydrocarbons, if the statement made by Sir Boverton Redwood is correct that "the coral reefs of the Red Sea are charged in places with recent petroleum, formed in that torrid climate from the swarming organisms occupying the shallow pools."1

Jan 5, 1917

By N. H. Cone

It is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

By D. R. Franklin, L. L. Lien, C. W. Hoffman

The initial operation of a mining facility is a unique and often underplanned phase of the Project development process. The subject of this presentation is a detailed strategy to effectively and efficiently bring a mining facility to design production capacity. This plan has been applied successfully on projects. It addresses developing the initial operation organization, management of information and problem, putting an appropriate management system in place, developing operations and maintenance information, and effectively training personnel.

Jan 1, 1983

By A. B. Wilder

We study the past Because it is a guide to the present and a promise for the future. The struggle for a better world is strengthened By the hopes, ambitions, and deeds Of those who were before us. As we look backward Our attention is directed forward. ONE hundred years ago, the manufacture of steel from molten pig iron without the use of fuel first began. In the earlier part of the nineteenth century the crucible process was the principal steelmaking method. It was a costly process, producing only a few pounds of steel at a time; so, most of the ferrous metal output was in the form of wrought or pig iron. With the perfection of the converter technique it became possible to produce low cost steel by the ton, thereby completely changing the structure, not only of the ferrous metal industry, but also of industrial production in general. This was the turning point from the Iron Age to the Age of Steel. William Kelly (Fig. 2), Sir Henry Bessemer (Fig. 1), and Joseph G. Martien experimented with the process before 1856. William Kelly began in Eddyville, Ky., in 1847 and has been given credit for first discovering the principle of the pneumatic converter process. Several years later in England Henry Bessemer independently conceived a steelmaking process similar to Kelly's. Bessemer made public his invention at the annual meeting of the British Association for the Advancement of Science held at Cheltenham, England, August 1856. As a result of his paper, "On the Manufacture of Malleable Iron and Steel Without Fuel," and his progressive leadership in the years to follow, the process became permanently identified with the name, Bessemer. Credit for the commercial adaptation of the process must be given two additional persons. Robert Mushet (Fig. 3) in 1856 in England recognized the necessity of deoxidation and recarburization of the converter product and evolved the technique for adding high manganese iron following the blow. In Sweden, in July 1858, G_ F. Göranson [ ]

Jan 1, 1961

By Robert E. Thurmond, E. D. Spaulding, Walter E. Heinrichs

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development.

Jan 2, 1954

Jan 1, 1910