Search Documents

By Jerry L. Straalsund, D. Bruce Masson

A dew-point technique was used to determine the thermodynamic activity of zinc at 430°C in a series of e phase Ag-Zn alloys. The composition of the alloys ranged from 72 to 88 at. pct Zn. This range included the composition at which Massalski and King3 found a reversal in the composition variation of the crystallo-graphic c/a ratio, which they attributed to an overlap of the Fermi surface across the (002) faces of the Brillouin zone. The data is presented in a graph in which RT In yz,, where yz, is the activity coefficient of zinc, is shown as a function of atomic percent zinc. This curve has an unmistakable change in slope at the same composition that Massalski and King observed the beginning of the reversal in the c/a ratio. This change in slope of the thermodynamic data is also attributed to a Brillouin zone overlap. Equations are presented to demonstrate that the thermodynamic activity can be related to the density of states of the conduction electrons, and that the observed phenomena are consistent with this model. It is also demonstrated that the contribution of the density of states can be related to the excess stability, a phenomenological parameter recently shown by Darkeen" to be significant in the interpretation of thermodynamic data of metallic phases. The data seem to indicate that zone overlap has caused a spinodal point, and the resulting misci-bility gap, in the phase diagram. THE problem of developing an adequate thermodynamic model of solid solutions has proven to be difficult, and is still only partially solved. The main approach has been to develop a statistical model, such as that of an ideal solution, regular solution, and so forth, to which can be attached corrections for electronic, vibrational, magnetic, ordering, or other contributions. Such corrective terms are usually derived on an ad hoc basis, and it is difficult to predict in advance what their relative importance will be. This problem has been discussed in general terms by Oriani and Alcock,' who have reviewed several thermodynamic models and a few empirical correlations. The measurements described in the present paper were made to demonstrate in a special case the importance of one such corrective term, the contribu- tion of the energy of the conduction electrons of an alloy. It was our premise that the contribution of the energy of the conduction electrons to the thermodynamic activity of the alloy components could be detected; further, that such an effect would be observed at alloy compositions where other phenomena, also ascribed to the energy and density of states of the conduction electrons, are observed. The idea of the importance of the conduction electrons is hardly new. Hume-Rothery and his adherents have developed the well-known theory of alloy phases in which the sequence of phase fields in binary equilibrium diagrams, especially those involving the noble metals with the IIB, IIIB, and IVB subgroups, can be correlated by replacing the composition variable with the ratio of conduction electrons to atoms, e/a. Jones and others have developed a physical explanation for this correlation, in which they consider the solubility limits of phase fields to be restricted by an intersection between the Fermi surface and a Brillouin zone. The general features of the model are also quite well-known—presumably zone intersection causes the density of states to decrease at critical alloy compositions. The attendant increase in energy of conduction electrons in the original crystal structure allows an alternate structure to become more stable as the concentration of polyvalent solute is increased. In spite of the wide acceptance of these ideas on phase stability, there is only indirect* evidence, such as the variations in lattice parameter recorded extensively by Massalskizy3 and others, that Brillouin zone interactions occur. There are few experimental measurements, other than the correlations of the phase sequence, that substantiate the premise that the energy of conduction electrons affects the solubility limits of alloy phases. Much thermodynamic data of alloys has been found to be consistent with the theory; yet there is a lack of detailed data at compositions where zone intersection and overlap are thought to occur. One would expect that the energy of the conduction electrons would make a measurable contribution to the thermodynamic properties of alloys at compositions near zone intersection and overlap if the theory of Hume-Rothery and Jones is correct. This conclusion cannot be avoided, because the phase boundaries are determined by the requirement that the chemical potential of the components be equal in both phases at equilibrium. An electronic effect large enough to alter the stability of a phase should also affect the thermodynamic activity by a measurable amount.

Jan 1, 1969

By W. K. Hartley

INTRODUCTION AND HISTORY The Kimberley Division of De Beers Consolidated Mines Limited includes four underground mines in Kimberley viz. Dutoitspan, Bultfontein, De Beers and Wesselton Mine and two outside mines, viz. Finsch, an opencast operation and Koffie- fontein, an underground operation. Figure 1 is a map of the Kimberley district showing the location of these mines. Finsch is 150km west of Kimberley and Koffiefontein is 80km south of Kimberley. The head office of the De Beers Company is in Kimberley. The diamond sorting and trading companies for diamonds produced in South Africa are also in Kimberley. Diamonds were first discovered in the Kimberley area at Hopetown in 1866 on the banks of the Orange River. This, and later finds, triggered the start of the great "Diamond Rush". In 1870 the Jagersfontein (now closed) and Dutoitspan pipes were discovered, followed by those at Bultfontein, De Beers and Kimberley Mine (now closed) in 1871, Koffiefontein in 1880 and Wesselton in 1891. Finsch Mine was a more recent discovery in 1961. Finsch, due to go underground in 1986, and Koffiefontein, are fully self-contained with their own treatment plants, housing, services etc. The four Kimberley mines deliver ore by conveyor to a central treatment plant and use joint ser- vices. ,+lining is presently carried out mainly by Block Caving which has replaced the earlier Chambering method. De Beers Mine, on a limited scale, and Wesselton Mine have recently started to use Sub-Level Caving, and both Bultfontein and Du- toitspan are scheduled to use the same method at a later date. The combined ore tonnage produced by the Kimberley Mines is 17 400 tons per day, Koffiefontein 12 000 tons per day and Finsch Mine 17 000 tons per day. THE EVOLUTION OF MINING METHODS Initially, the open-cast mining was carried out to as great a depth as safety would permit. In the early stages of open-cast mining, the Kimberlite was removed in horizontal slices from levels 13m to 20m apart. The rock broken in the workings was raised to the surface by means of endless rope haulage inclines. As lower levels were attained these rope haulages were replaced by aerial hoists, inclined shaft haulages or inclined skip-ways. These methods were dependent upon the strength of the unsupported pipe walls, which became increasingly unstable with depth and a system was adopted whereby the ground mined in open excavations was tipped down passes to tunnels connecting with vertical hoisting shafts sunk in the country rock. As work in the open pit became more and more impracticable due to extensive falls of ground, this system was replaced by a combination of open-cast and underground mining, and eventually by wholly underground methods. Chambering With the advent of underground mining, a system known as "Chambering" (or "Inclined Chambering") was evolved. It was essentially a combination of shrinkage stoping and caving, whereby advantage was taken of the high pressure exerted by the loose rock that had accumulated in the open excavations due to the collapse of the pipe walls. This mining method was introduced around 1890 and was successfully employed, with little change, up to the early nineteen seventies. In this system each mine was served by a main hoisting shaft situated about 300m in the country rock. Main haulage cross cuts were driven from the shaft to the pipe at 200m (600ft) vertical intervals. A sub-vertical shaft, situated close to the pipe provided access to the working levels. Chamber levels were established from the sub-vertical shaft at 13m (40ft) intervals. See figure 2. On each of these levels successive 6,8m wide “cuts" were mined out across the pipe, from one rock contact to the other, and extended vertically to the footwall of the level above. Every 6,8m cut was made up of a chamber and a "back-pillart1, each approximately 3,401 wide. The chamber was mined by overhand shrinkage stoping. The levels were carried "en echelon", with each chamber on a level approximately three cuts ahead of the chamber on the level

Jan 1, 1981

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By H. T. Shore, J. M. Schultz

A number of experimental rnethods—X-ray powder diffractometry, Laue photography, X-ray small-angle scattering, and transmission electron microscopy and dijfraction—have been utilized to examine the morphology associated with precipitation from the terminal, g, solid solution of a Zn-1 pct Cu alloy. A significant age hardening was observed in a 1 pct Cu alloy. X-ray and electron diffraction results showed that the structural inhomogeneities associated with the hardening were isotructural with the matrix. The average size and shape of the inhomogeneities were deduced from the electron microscopy and X-ray small-angle scattering. The preprecipitates are hexagonal platelets some 300? in diam. and some twelve unit cells thick. The orientation of the platelets was deduced from Laue photographs and electron diffraction. The platelet plane is (0001). When a large amount of pre-precipitation is present in a localized volume the new lattice is often disoriented by a rotation about (0001) of of the matrix. WhILE dilute Zn-Cu alloys have been commercially important for some 50 years, relatively very little is known metallographically about this material. The "Zilloys", zinc with about 1 wt pct Cu and sometimes a small addition of magnesium, are used to produce rolled zinc which is harder and stronger than that produced by other rollable zinc alloys.' According to the phase diagrams of the zinc-rich side of the Cu-Zn system, such dilute Zn-Cu alloys should age-harden;2-5 the solubility of copper in zinc, g-phase, at 424°C is 2.68 pct, while at 0°C it is only to 0.3 pct. However, the published literature on the aging of this system appears to be limited to a documentation of the contraction of 1, 2, and 3 pct Cu alloys aging at 95°c,6 and an attempt to measure changes in lattice parameters during aging.' In the latter work, no lattice parameter changes were detected, although a broadening of the highest-angle lines was detected and considerable diffuse scattering was observed. Micro-structural investigations have been limited to the latest stage of aging, wherein Widmanstatten precipitates are formed.3,47 These alloys are of interest for still another reason. The two most zinc-rich phases in the Cu-Zn system, 77 and E, are both hcp. Moreover, the change in a, between 17 and t for a 1 wt pct Cu alloy is onlv 3.64 -,~ct: the change in Co is 12.0 ict. It would be anticipated that precipitation in such a material might occur through metastable phases or G.P. zones with epitaxy along mutual 0001 planes. The goals of the present work are aimed at partially filling the void of knowledge concerning the early stages of precipitation from the g phase. In particular, we have attempted to document the magnitude of the age hardening of this system and to determine the size, shape, and orientation within the matrix of the elements of precipitation in an early stage of condensation. EXPERIMENTAL A) Specimen Preparation. Specimens were prepared In two somewhat different ways, one method being used for X-ray Laue and diffractometer measurements, optical microscopy, and Rockwell hardness measurements and the other used for electron microscopy and X-ray small-angle scattering. In the first case zinc and copper in the proper proportions to yield a 1 wt pct Cu alloy were melted together in a closed graphite crucible. Castings so made were free of apparent segregation or oxidation. The castings were then solution-annealed at 400°C for several days and then quenched in water to room temperature. Filings of portions of the specimens were made for use as X-ray powder diffractometry specimens. The electron microscope material was made as follows. Castings were made under vacuum with copper powder placed inside a hollow zinc cylinder to insure good contact of the materials. These 1 wt pct Cu pieces were then rolled to 0.1 mm with an intermediate anneal in vacuo. The rolled sheets so formed were then annealed for about 6 hr at 225°C. Finally the specimens were electropolished slowly until thin enough for transmission electron microscopy. The polishing is discussed in greater detail in the Results section. B) Measurements. X-ray measurements of three types were performed. A G.E. XRD-5 diffractometer was used to examine powders of the alloy for identification of second-phase material. A Kratky small-angle camera, also operating from a G.E. tube, was used to investigate the sizes of small precipitate particles. In both cases, nickel-filtered copper radiation was utilized. Finally, individual grains of the large-grained castings were examined in the back-reflection Laue geometry. Electron microscope studies were carried out with a J.E.O.L. Model 6A instrument. RESULTS A) Hardness Measurements. Hardness measurements performed at room temperature on the large-grained polycrystalline specimens showed a hardening which was essentially complete in 3 hr. Fig. 1 shows a typical plot of hardness vs aging time. The relative magnitude of the ultimate hardening varied from run to run between 150 and 200 pct of the value for the material immediately after quenching from the solution anneal. Most probably the variations reflect small changes in the time taken to remove the specimen from the vacuum furnace after the solution anneal.

Jan 1, 1969

By E. A. Slover

THE usual reverberatory system of smelting cop--1- per concentrate or calcine has for its component parts a furnace and one or two waste heat boilers. These parts are operated on a basis of compromise, since the furnace can send gas to the boilers at too high a temperature and the boilers by plugging, due to dust or slag, can place a definite limit on the amount of fuel the furnace can burn. Over the years the copper concentrate smelting furnace has had few advances in design. The simple rules of design such as the flame should wipe the bath and the speed of the gases should be reasonably low for dust carrying purposes seem to cover the main features. In the construction of the individual furnaces some innovations are always being introduced. Among these are charging so that the work of smelting is a complete bath process, the use of suspended brick arches in place of sprung arches, the use of basic brick, not only in the crucible, but also in roof and sidewalls, the use of various means to feed the charge, the use of magnetite or other heavy material to construct the hearth, water cooling of bridgewall and slag skimming bay, the smelting of raw charge instead of calcine, the use of preheated air, and possibly the use of oxygen-enriched air for combustion. But the general outlines of the furnaces have not changed much except as to size. Furnaces at Hurley As shown on Fig. 1, the furnace at Hurley is 126 ft long between the longitudinal buckstays and 32 ft wide at the skewback plates. The foundation is a concrete retaining wall with piers at intervals that go deeper into the earth. Purposely the wall at the burner end of the furnace is not backed-up as tightly as the other parts of the foundation so that movement due to expansion may take place here rather than into the boiler foundations. Within these foundation retaining walls of concrete, the earth has been removed to allow the placement of the crucible brick base inside of which a silica hearth is laid 4 ft 6 in. in depth. No expansion is left in the brick base and crucible where they are in contact with the hearth. The hearth itself is of quartzite crushed to 1 in. size with fines left in the product. An 8 in. layer is laid and tamped with paving tampers to about 6 in. in thickness. Then a layer of silica flour is spread and vibrated into the hearth. This operation is repeated until a depth of 4 ft 6 in. is occupied by the silica mass onion-skinned in layers of approximately 6 in. Before firing the entire hearth is covered with broken slag to a depth of 4 in. so that a seal may be formed on the hearth. The crucible is completely faced with magnesite chemically bonded brick while the outside, against the foundation, is made of silica brick. The side-walls are carried up with silica brick in which expansion joints are left at intervals. Above the crucible the sidewall is corbelled to form a shelf on which the charge may build up along the side-walls, see Fig. 2. The arch of the furnace is sprung 20 in. silica brick, with the longitudinal centerline horizontal the length of the furnace, and some 9 ft in the center above the bath. Both straight and wedge brick are used in the construction and a thin silica mortar is troweled for joints. After the arch under heat has assumed its permanent shape, a silica slurry is spread over the arch to fill any cracks that have formed, thus giving bearing surface to the brick and preventing dust from entering the body of the arch to act as a future fluxing agent. The uptake of the furnace slopes up to the boiler entrance where a brick pilaster divides the gas stream for the two boilers. Over this flared uptake is a suspended flat arch of firebrick. The pilaster and sidewalls are constructed of firebrick but the bottom of the uptake is lined with silica brick and fettled through holes in the roof with siliceous fettling. Close to the entrance of each boiler is a brick covered slot through which water-cooled dampers may be lowered in event of boiler trouble. These water-cooled dampers are hung permanently in position ready to be lowered when needed. Flexible hoses to follow the dampers as they are lowered are connected at all times and individual chain blocks are used to lower the dampers. A pump supplying water is started before the dampers enter the heat. Charging of the furnace along the sidewalls for some 80 ft from the bridgewall is accomplished by electric vibrating conveyors fed by belt from charge storage bins above the furnace. These conveyors

Jan 1, 1954

By G. R. Kotler, W. A. Tiller, H. V. Ashcom, S. O&apos, Hara, W. C. Johnston

The grain-refinement effect of electromagnetic stirring of Sn-Pb alloys during solidification is investigated at higher field strength and in larger-sized samples. It is found that the grain-refining effect is due to a crystal multiplication phenomenon rather than a nucleation phenomenon. The effect increases with sample size for a fixed field strength and a fixed supercooling bath temperatures. The effect in other alloys was investigated. IN a recent publication1 it was reported that significant grain refinement could be produced during the solidification of a supercooled melt of Sn-Pb alloy when a critical degree of electromagnetic stirring was present in the melt. Thus, for a particular supercooling, AT, a critical magnetic field, Hc, existed at which the number of grains per unit volume, n, increased rather abruptly by a factor of 103 to 104 as the field, H, was increased by a small amount. It was further found that the undercooling at which the melt spontaneously nucleated, ?Tn, was independent of the magnetic field. These authors matched their experimental results against the qualitative expectations of existing theories and found each theory somewhat unsatisfactory. One important question that was not answered in this previous work was "should the effect be classed as a nucleation phenomenon or as a crystal-multiplication phenomenon?" Other valid questions that need answering are: i) do higher magnetic field strengths alter the nature of the results?; ii) what is the effect of higher lead content in the alloy?; iii) what changes occur when one extends the experiments to larger-diameter samples?; and iv) is this a universal effect applicable to the grain refinement of all materials? The present work directs its attention to answering these five questions. The

Jan 1, 1965

By W. Weissberger, Frankiewicz, L. Pommier

Introduction In the U.S., about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacing these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal in unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still have a long way to go and costs are very high. Another option, which appears very attractive, is the use of solid coal in a liquid fuel form - coal slurry fuels. Occidental Research Corp. has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC), a wholly-owned subsidiary. Both coal-oil mixtures and coalwater mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality metallurgical coals. There are a number of incentives for potential users of coal slurry fuels and in particular for coal-water mixtures (CWMs). First, CWM represents an assured supply of fuel at a price predictable into future years. Second, CWM is available in the near term; there are no substantial advances in technology needed to provide coal slurry fuels commercially. Third, there is minimal new equipment required to accommodate CWM in the end-user's facility. Fourth, CWM is nearly as convenient to handle, store, and combust as is fuel oil. Several variants of CWM technology could be developed for different end-users in the future. One concept is to formulate slurry at the mine mouth in association with an integrated beneficiation process. This slurry fuel may be delivered to the end-user by any number of known conveyances such as barge, tank truck, and rail. Slurry fuel would then be stored on-site and used on demand in utility boilers, industrial boilers, and potentially for process heat needs or residential and commercial heating. An alternative approach is to formulate a low viscosity pre-slurry at the mine mouth and to pipeline it for a considerable distance, finishing up slurry formulation near the end-user's plant. Finally, at the other extreme of manufacturing alternatives, washed coal would be shipped to a CWM manufacturing plant just outside the end-user's gate. Depending on fuel specifications and locations of the mine and end-user facility, any of these alternatives may make economic sense. They are all achievable in the near term using existing technology or variants thereof. The Coal-Water Mixture CWMs contain a nominal 70 wt. % coal ground somewhat finer than the standard pulverized ("utility grind") coal grind suspended in water; a complex chemical additive system gives the desired CWM properties, making the suspension pumpable and preventing sedimentation and hardening over time. Figure 1 shows the difference between a sample of pulverized coal containing 30 wt. % moisture and a CWM of identical coal/water ratio. The coal sample behaves like sticky coal, while the CWM flows readily. The combustion energy of a CWM is 96-97% of that associated with the coal present, due to the penalty for vaporizing water in the CWM. Potentially any coal can be incorporated in the CWM, depending on the combustion performance required and the allowable cost. CWMs are usually formulated using high quality steam coals containing around 6% ash, 34% volatile matter, 0.8% sulfur, 1500°C (2730°F) initial deformation temperatures, and energy content of 25 GJ/t (21.5 million Btu per st). Additional beneficiation to the 3% ash level can be accomplished in an integrated process. There are a number of minimum requirements which a satisfactory CWM must meet: pumpability, stability, combustibility, and affordability. In addition, a CWM should be: resistant to extended shear, generally applicable to a wide variety of coals, forgiving/flexible, and compatible with the least expensive processing. It was found that a complex chemical additive package and control of particle size distribution are necessary to achieve these attributes simultaneously, while maximizing coal content in the slurry fuel. Formulation of Coal-Water Mixtures A major consideration in the manufacture, transportation, and utilization of a slurry fuel is its pumpability, or effective viscosity. Most CWM formulations are nonNewtonian, i.e., viscosity depends on the rate and/or duration of shear applied. Viscosities reported in this paper were obtained using a Brookfield viscometer fitted with a T-spindel and rotated at 30 rev/min, thus they are apparent viscosities measured at a shear rate of approximately 10 sec-1. The instrument does reproducibly generate a shear field if spindle size and rotation rate are held fixed. By observing the apparent viscosities of several slurries at fixed conditions it is possible to obtain a relative measure of their viscosities for comparison purposes. A true shear stress-shear rate relationship at the shear rates at which the CWM will be subjected in industry may be obtained using the Haake type and a capillary viscometer. These viscometers are used for specific applications. However, for comparison purposes, apparent viscosities are reported.

Jan 1, 1985

By C. Wert, D. Keefer

The results of this study indicate that sudden increases in aging temperature lead to reversion phenmena in carbon in the a, iron system. These phenomena are thought to be associated with the dissolution of carbide precipitates. Reversion is studied with respect to three variables: 1) Specimen grain size, 2) the initial amount of carbon in solution, and 3) difference between initial and final aging temperature. It is found that of these variables the initial carbon concentration has the greatest effect on reversion. THE solid solution of carbon in n iron has been the subject of numerous investigations throughout the past few years. Despite the great amount of effort which has been put forth toward understanding this system, however, there persist a number of interesting aspects of the system which are open to further research' Studies Of the precipitate which forms as a result of aging a supersaturated solution of carbon in a, iron appear to be particularly interesting. The present work is an attempt to determine certain

Jan 1, 1960

By Anthony G. Reid

INTRODUCTION At the time of the death of Mao Tse-tung in 1976, China was a major oil producing country with a daily oil flow in the order of 1.735 million barrels. This position had been achieved with minimal assistance from the outside world. Further, only some fifteen years had elapsed since the country's daily oil production capacity had hovered at the barely significant level of one hundred thousand barrels. Why then did the new leaders of China, after this very creditable record of success, suddenly change the direction of the country's drive for future hydrocarbon production? First, by switching much of the emphasis of exploration from onshore to the offshore continental shelf basins, and further by apparently abandoning the philosophy of self reliance calling upon the world's oil industry to share in the task of locating and developing these potential offshore energy reserves. The answer is probably only partly understood by those of us outside China, However, a number of factors exerting an important influence on this decision can be identified. THE MOVE OFFSHORE The new leadership was anxious to rapidly move China into her rightful place amongst the powerful and technologically advanced nations of the world. Modernization became the slogan, specifically modernization on four fronts, agriculture, industry, technology and military with the goal to "catch the west by the year 2000". But how to generate the capital to finance this massive modernization program? The rapid escalation of the price of crude oil following the 1973 Oil Embargo and the continuing apparently insatiable world demand for this now extremely precious primary resource was very clear to all. China, as a major producer, could export crude to help finance the ambitious development programs of the government. To do this, however, would require a very significant in¬crease in present production capacity, as the domestic demand even for China with her relatively low per capita energy consumption, is essentially equal to the current production. Trying to rapidly move the new regime's programs into actions, one can only assume that the planners looked at the success of the petroleum industry over the preceding fifteen years and quickly concluded that this well established curve could be maintained and indeed steepened with an increase in effort. The rapid discovery of a few more Daqing's (China's premier oil field, producing one million barrels a day) would have the country's ambitious modernization goals within reach. Petroleum would At the time of the death of Mao Tse-tung in 1976, China was a major oil producing country with a daily oil flow in the order of 1.735 million barrels. This position had been achieved with minimal assistance from the outside world. Further, only some fifteen years had elapsed since the country's daily oil production capacity had hovered at the barely significant level of one hundred thousand barrels. Why then did the new leaders of China, after this very creditable record of success, suddenly change the direction of the country's drive for future hydrocarbon production? First, by switching much of the emphasis of exploration from onshore to the offshore continental shelf basins, and further by apparently abandoning the philosophy of self reliance calling upon the world's oil industry to share in the task of locating and developing these potential offshore energy reserves. The answer is probably only partly understood by those of us outside China, However, a number of factors exerting an important influence on this decision can be identified. THE MOVE OFFSHORE The new leadership was anxious to rapidly move China into her rightful place amongst the powerful and technologically advanced nations of the world. Modernization became the slogan, specifically modernization on four fronts, agriculture, industry, technology and military with the goal to "catch the west by the year 2000", But how to generate the capital to finance this massive modernization program? The rapid escalation of the price of crude oil following the 1973 Oil Embargo and the continuing apparently insatiable world demand for this now extremely precious primary resource was very clear to all. China, as a major producer, could export crude to help finance the ambitious development programs of the government. To do this, however, would require a very significant increase in present production capacity, as the domestic demand even for China with her relatively low per capita energy consumption, is essentially equal to the current production. Trying to rapidly move the new regime's programs into actions, one can only assume that the planners looked at the success of the petroleum industry over the preceding fifteen years and quickly concluded that this well established curve could be maintained and indeed steepened with an increase in effort. The rapid discovery of a few more Daqing's (China's premier oil field, producing one million barrels a day) would have the country's ambitious modernization goals within reach. Petroleum would be the principal bridge to the bright future. The next decision involved the question of where to look for these vast new reserves. Chinese exploration teams had already looked at most of the onshore sedimentary basins and, while they were the first to admit that there was much yet to do, it was fairly clear to them that the potential for large new accumulations was confined to two areas: the little explored, remote, inhospitable regions of western China, principally Xinkiang Province and the equally unexplored offshore basins of the continental shelf and slope. In both cases China faced a very serious problem. The inhospitable environments were severely straining her petroleum industry's current technological ability to cope, particularly as the government needed rapid results. Thus the pragmatic and, to the foreign oil industry, unexpected decision to invite cooperation with the outside world. The reasons for the initial emphasis on the exploration of the offshore basins with the cooperation of foreign oil companies are again supposition on my part, but probably involved considerations of technical merit, ease of development and delivery to markets together with more sensitive issues such as controling the influence of foreign philosophies and values on the Chinese population by containing most foreign activity to the offshore. So within three years of the death of the great helmsman, China had developed a plan to involve foreign oil companies, both state and private, in a grand plan to rapidly increase the nations oil production. In fact, by this time, the first round of talks had been concluded and the first phase begun, and what a beginning. Some forty eight companies from thirteen countries had signed documents to participate formally in this world scale event. It was far easier to list those companies which did not participate than to list those which did. FOREIGN COMPANY INTEREST Why the rush by the world's oil industry to be involved in China? What was China offering which made everyone so anxious to join in? Again the answer is complex in detail, but principally involved a combination of factors which together caused this virtual stampede. Timing was a major element. Oil Companies, despite an ever increasing take by governments, were beginning to benefit. from the' rapid escalation of crude prices induced by OPEC and were looking for suitable areas to reinvest these funds. Producers

Jan 1, 1982

By Sven Fornander

L. F. Reinartz (Armco Steel Corp., Middletown, Ohio) —I would like to know, in the practical application of the Kalling process, what kind of a lining was used, how thick was the lining, and how much metal was treated at one time? S. Fornander (author's reply)—The rotary furnace is lined with a course of fireclay bricks 6 in. thick. This course is backed by 5 in. of insulation. The furnace has a capacity of about 15 tons. Mr. Reinartz—How was the ladle preheated? Mr. Fornander—As pointed out in the paper, the furnace was heated by a gas flame in the beginning of the experiments. During these first tests, however, the desulphurization was inconsistent. We think that this was due to the fact that iron droplets sticking to the furnace walls were oxidized by the gas flame. Now, the furnace is operated without preheating of any kind, and the results are much better. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—I might add one comment. This furnace was heated with a flame and for a time they had a little difficulty due to some residual metal in the rotating drum that would oxidize in between treatments and they found therefore, that it was very essential to drain the drum completely of metal so that they would not build up any ferrous oxide between treatments and they eliminated some of their erratic heats by maintaining those more reducing conditions. It was interesting to watch this operation. As soon as the drum started to rotate there was considerable flame, at least, at the time I saw it, that came out around the flanges, indicating there was quite a little pressure on the inside of the drum. W. 0. Philbrook (Carnegie Institute of Technology, Pittsburgh)—Is the reaction slag in the Kalling process liquid or solid, and how is it separated from the metal? Mr. Fornander—In the process there is no slag in the usual sense of the word. The lime powder does not melt during the treatment. After the treatment the lime is still in the form of a fine powder. It is separated from the metal by means of a piece of wood of suitable size placed within the furnace before it is emptied. D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—Dr. Chipman has given us some of his ideas in connection with a specific effect of silicon and silica on sulphur elimination and how silicon might interfere with desulphuriz- ing in the blast furnace. I wonder if he would like to elaborate on the possibility of a similar effect of silicon in the Kalling process? J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—Silicon does not interfere with the Kalling process. Anything that has strong reducing action is good for desulphurization. In these tests where the temperature was low compared to blast furnace temperatures, the silicon that is in the metal is a better reducing agent than the carbon. At high temperatures, carbon is the better. It is not the silicon in the metal that interferes with desulphurization, it is the silica in the slag. Mr. Joseph—I might add that the metal that was tapped from the drum after desulphurization was really at quite a low temperature. It was not measured, but I think it was well under 1300 °C, probably 1200" or a little above that. That was one of the difficulties, and I think there is no question about the fact that the Kalling process—in that it affects desulphurization between powdered lime, solid and liquid iron— is a reaction definitely between the solid lime and the liquid iron. E. Spire (Canadian Liquid Air, Montreal, Canada) — This Kalling process seems very interesting to us and after all it is only a mixing action that is taking place between the iron and the slag. We have attempted to do the same thing in another way. We have placed at the bottom of the ladle a porous plug through which we injected an inert gas. It can be nitrogen or argon. This plug is placed at the bottom of the conventional ladle and gas injected through the plug. That has appeared in our patent. To define this new type of treatment, I use the word gasometallurgy. I do not know if you like it, but it is a way of defining methods of treating metal using gases. What we do is exactly what is done in the exchange process in another way. We have a porous plug at the bottom with a high lime slag on top of the metal. Using this method, we have very good agitation of metal and slag, and with a small flow of gas, we can achieve a very strong agitation. For instance, in the 500 lb ladle, we use only 5 liters of gas a minute. We have an agitation compared to very rapidly boiling water in a pail. Moreover, the agitation can be controlled to create any amount of mixing desired. In a few minutes, with this method, the sulphur dropped from 0.58 to 0.11. These results have been improved since, and we have obtained results like 0.08

Jan 1, 1952

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By L. A. Weitzenkamp, N. M. Bashara

A study of the electrical conductivity of gold films less than 200 in thickness indicates a negative temperature coefficient of resistance and a thermal actiuatlon energy of less than 0.25 ev. The films consist of discrete metal islands of linear dimensions from a few angstroms to 1000A. Films were able to withstand applied fields up to 60,000 v per cm before breakdown occurred. A model for the conduction mechanism is proposed which involtes a Potential barrier due to work junction, irriage forces , and an electrostatic potential arising from separating an electron from a neutral island leaving behind a positively charged metal island. Activation energies of less than 0.25 ev ave consistent with this model, which includes a tunneling andor Thermal mechanism for conduction between the separate metal islands. An apparent satuvation effect in conductivity at high fields is observed experimentally. The saturation effect may be explained by the influence of the electrostatic contribution to the potential barriers for the transition through several islands adjacent to the original island which was activated to give up an electron. The proposed model gives Poor quantitative agyeement for the intermal electrical field between islands. ThIS paper will relate the structure of discontinuous metal films to the electrical properties and will emphasize the following topics: 1) the relation of the conduction mechanism to particle size and a comparison of particle size from electrical measurements with electron-microscope studies; 2) the saturation of the conductivity at high electric fields; and finally, 3) a comparison between the external field applied and the apparent field between particles. che- latter comparison points to a need for a modification in the model for the conduction mechanism first proposed by orter' and expanded by Neugebauer and webb2 which will be dealt with in the discussion. The paper is based on results on gold films on glass microscope slides. The clms were vacuum-evaporated and were about lOOA thick, thickness being measured by interferometry. It has been observed that metal films of this thickness do not exhibit bulk metallic conduction. Films thinner than some critical thiclmess, depending upon substrate temperature and other factors, have conductivities which increase with increasing temperature with thermal activation energies of less than 0.25 ev. Electron-microscope studies3 have shown that these films consist of discrete metal islands having linear dimnsions from a few angstroms to approximately 1000A. When the metal is being vacuum-deposited on the substrate, islands on the order of a few angstroms appear first. As the deposition continues the islands may tend to agglomerate into larger particles and may eventually grow together into a continuous film,3''' In our tests the conductivity of the gold films was found to be about ten orders of magnitude less than the bulk conductivity of gold. When oxygen was introduced into the test chamber the conductivity decreased by a factor of about one-third. This can be related to an increase in work function for gold caused by adsorption of oxygen, as reported by Oullet and Rideal.s Exposure to an atmosphere of water vapor caused an increase in conductivity by a factor of 2 or 3 when a low field was applied. When the films were exposed to water vapor under a high field the conductivity increased by as much as two orders of magnitude. The activation energies measured were much less than the work function for gold, 0.25 ev or less, with the smaller activation energies observed for thicker films. It will be shown that the activation energy is a function of particle size and spacing. In general the model for the potential between metal islands would include the effective work function, the image force, the applied field, and an electrostatic term. The electrostatic contribution arises from the potential required to separate an electron from a conducting sphere. According to Neugebauer and webb2 the maximum potential due to the field and the electrostatic term only is

Jan 1, 1967

By A. Faison Dixon

In India the production of mica, which in other countries is of very minor importance, is one of the staple, long established industries, and ranks high in the statistics of mineral products. Nearly two-thirds of the mica of commerce comes from India. The Indians have used mica for glazing and decorative purposes through many centuries. About 14,000 men are employed in and about the mines, and the indigenous and primitive mode of mining is still followed; but, by reason of the exhaustion of the surface supply hitherto won without intelligence or capital, it will not be many years before the present interesting and casual methods will be replaced by a less archaic and more profitable system. India on the whole has little mineral wealth, but the unique resources of its mica-fields, cheap labor, and favorable natural conditions render it unlikely that any other country can ever more than temporarily contest her leadership in the production of this one minor but essential mineral. Mica plays a small but indispensable rôle in a variety of fields of dissimilar application. Its use and value depend upon characteristics which different kinds of mica have in varying degrees, each kind being adapted to its own special purpose. Its well-known characteristics of transparency, flexibility, elasticity, toughness, high dialectric strength, perfect flatness, ease of splitting into thin films, ability to stand high heat and sudden changes in temperature, give it value in many industries. No other substance, natural or artificial, has the same combination of qualities. The oldest use of mica is in glazing. By reason of the improvements in annealing glass, this is not now of great importance, but mica is still employed for the covers of ikon images in Russian churches, the windows of anthracite stoves, compass

Jan 1, 1914

By J. S. Billheimer, H. H. Reamer, B. H. Sage

Jan 1, 1949

By H. H. Reamer, B. H. Sage, J. S. Billheimer

Jan 1, 1949

By AIME AIME

UNQUESTIONABLY the Coal Division has never had a meeting in which so many outstanding technical papers were presented of immediate practical application to problems of personnel, mining, safety, preparation, combustion, and carbonization. Should there have been those present with the lingering idea that all that was needed for success in the coal industry was a strong back and a weak mind they must have had a rude awakening.

Jan 1, 1942

Jan 1, 1944

By William L. Swager

This is the second in Mining Engineering's series of articles on sources, uses, production, and conservation of strategic minerals. "Cobalt" first in the series, appeared in February 1951.

Jan 5, 1951

By D. W. Fuerstenau

In recent years, various advances have taken place in the flotation recovery of fine mineral particles. A number of new approaches to recovery of fine particles have been proposed. In this paper, the background and performance of some of these tech- niques for fine particles processing are reviewed. A brief sum mary of the problems associated with fine particles in flotation and related processes is presented.

Jan 1, 1980

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910