Search Documents

By E. S. Machlin

The kinetics of vacuum distillation, vacuum-melt surface reactions, crucible-melt surface reactions and boiling are analytically investigated. No disagreement with experiment is obtained upon applying a rigid flow model to describe the behavior of the melt in the vicinity of reaction surfaces. The theory focuses attention upon measureable parameters rather than upon the adjustable parameter, stagnant layer thickness, associated with other theories. The rigid flow theory is thus capable of quantitative evaluation and experiments to achieve this evaluation are suggested. KINETICS, rather than thermodynamics, often determine the degree of refinement achieved in vacuum melting. There is little understanding, however, of the kinetic principles involved in vacuum refining. This paper represents an attempt to achieve this understanding. There are two reactions which need to be con- sidered. The first is the refining reaction. The second shall be called the polluting reaction. It is the reaction associated with the introduction of components of the crucible into the melt. The mechanisms of both reactions are unknown. Many models can be constructed to describe either the refining or polluting reactions. For example, consider the refining reaction C + Q = CO(g). One model that can be imagined is that the carbon and oxygen combine in the melt to form CO which then diffuses to a melt-

Jan 1, 1961

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Richard Franchot

From an efficiency viewpoint, the greatest loss of energy to the blast furnace is in its failure to convert more than about a third of the coke carbon from carbon monoxide to carbon dioxide. This result has usually been ascribed to a necessity of a 2:1 excess of CO in order to reduce iron. It has, however, been proved that iron is completely reduced by equal volumes of carbon monoxide and carbon dioxide. Hence there is room for the hypothesis that vaporization, as cyanid, of accumulated alkalis is a serious primary factor limiting the ratio of ore to coke. Observed cyanid vapor concentrations and those measured by the variations of the nitrogen-oxygen ratio in the hearth gases form the basis for a quantitative explanation of the furnace action. As EVERYBODY knows, the blast furnace is a gas producer. As to the reason for this, people are not so well agreed. The significance of the fact is obvious, for the extent to which the fuel leaves the furnace as combustible gas measures poor economy in iron smelting; while good efficiency in this respect means poor gas. The furnace thus works at cross purposes. The present trend of the steel industry is toward. a primary use of the blast furnace as a gas producer with pig iron as a byproduct. Needless to say, this trend is away from improvement in iron making. The production of more and better iron in a given furnace consuming a given amount of coke would seem, at least, to involve a decrease in the relative proportion of the combustible gas. The possibility at the same time, however, of making more and better gas need not necessarily be excluded. (The more the furnace acts as gas producer, the bigger is the sulfur problem.) Whatever the object, it would seem desirable to have a, clear, comprehensive, mathematically exact estimate of why and how the blast furnace functions, to the large degree that it now does, as a gas producer. The literature does not give a definite answer to the question. That for which explanation is sought is the fact that only a minor part, usually not more than a third, of the coke carbon burned is oxidized to carbon dioxide; that the development in the furnace of the fuel energy is thus limited usually to little more than 50 per cent.; that it requires about twice as much fuel coke to make a ton of iron as is indicated by the rela-

Jan 7, 1925

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Lester C. Uren

THIS paper reviews the industrial trends and changes in educational concepts that have led to the development of the modern petroleum engineering curriculum. A trend toward emphasis on engineering fundamentals is noted. While most universities are committed to the traditional four-year engineering program, it is agreed that more than four years is necessary for academic preparation of the petroleum engineer in all phases of his profession. The author proposes a coordinated program of undergraduate and graduate training that will permit of adherence to the general pattern of the present four-year engineering course, with provision for extension of the program into specialized graduate courses of professional character. In the latter, emphasis may vary with the interests and objectives of the individual student. A specific undergraduate curriculum is proposed in which upward of 80 per cent of the available time is devoted to engineering fundamentals. A broad survey of the professional field is afforded in courses grouped in the third and fourth undergraduate years, but detailed treatment of the professional aspects of petroleum engineering is reserved for the graduate program. INTRODUCTION Of necessity, engineering curricula must ever be changing to reflect the new techniques, the changing concepts that are presented as the engineering industries develop and unfold. Particularly is this true of the younger engineering curricula representing comparatively new and rapidly changing industries such as the petroleum industry. Institutions that planned their petroleum engineering curricula a decade or two ago now find that the petroleum industry has become vastly more technical in its requirements. Entirely new methods and techniques have come into vogue and must be given place in the curriculum, and some of these are of a character that demands changing emphasis in the fundamental preparatory subjects. College and university faculties cannot complacently assume that curricula in this field that were considered appropriate 10 or 20 years ago still reflect the needs of the industry that they are designed to serve. If they do, their graduates will be poorly equipped to meet the requirements imposed upon them by a rapidly changing industry. Perhaps it is not too much to expect academic authorities to anticipate the trends of industry and equip their graduates with what they will need to attain leadership 10 or 20 years after graduation. Whether or not this desirable objective is possible, there is no excuse for allowing curricula to fall behind the current needs of industry. DURATION OF CURRICULUM The majority of our engineering schools and colleges still adhere to the four-year curricula and there appears to be a definite - sentiment among many engineers engaged in industry that work should be so planned that the engineering student may secure the essential academic preparation for his profession in a terminal four-year program. Yet, in recent years, it has become increasingly apparent that four years of

Jan 1, 1941

By Sandip K. Mukherjee, Anthony W. Laurito, Madan M. Singh, Jon C. Volkwein

In the past, little attention has been paid to the costs of ventilation, since it seldom represented a significant portion of the total mining cost. However, in recent years adverse mining conditions and increases in power charges have caused ventilation costs to rise. The federal regulations have set minimum standards for volumetric airflow rates in underground coal mines. As a mine develops, the air volume and pressure requirements increase. There are several methods by which the quantity of airflow to the mine and working faces can be increased. Some of the methods include (1) increasing main fan output or replacing the main fan by a new higher capacity fan, (2) reducing leakage across stoppings and overcasts, (3) adding a new ventilation shaft or borehole, (4) reducing resistance to airflow by reducing the resistance factor of the individual airways, increasing the number of airways (especially the parallel airways), or re- arranging the air courses by using the available entries, and (5) using auxiliary ventilation systems. This paper addresses the cost-benefit analysis of several of these alternatives as applied to a large operating coal mine located in southern Illinois. Pressure and quantity surveys were conducted under-ground, and measurements were taken at the main exhaust fans on the surface. The existing ventilation network was modeled by using the Penn State ventilation simulator. The input data included the configuration of branches, resistance of each branch (including a component for shock losses), and changes in pressure and volume. The results of the simulation were compared with the survey data to check the merits and accuracy of the model network. The net- work was designed to take into account shafts, major entries, overcasts, regulators, gob areas, working faces, and major leakage paths. The model network served as the basis for the cost analyses of networks designed for increased airflow. The applicable alternatives for increasing airflow were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each f the alternatives included capital, operating and maintenance costs. These costs were expressed as annual costs in terms of dollars per cfm of circulating air, taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. The result of these analyses show that for the short-range plans evaluated, the most cost-effective way of increasing airflow at this mine would be to reduce leakage through stoppings and overcasts.

Jan 1, 1982

By P. van Meurs

This paper describes a technique which permits visual observation of oil displacement processes througlrout the interior of a porous structure as thick as 2 in. A model having glass walls is filled with finely powdered glass. Such a model becomes completely transparent if the powdered glass pack is saturated with an oil having the same refractive index as the glass. When water or gar, with a refractive index different from that of the oil (glass) is injected, the model becomes opaque in the space occupied by the water (gar). visual observation and photography of these displacement processes are thus rendered possible. The following processes have been studied: (I) displacement of oil by water (linear drive) in a homo-geneous formation and in a stratified formation, (2) water flooding (five-spot well pattern), (3) solution gas-drive process, and (4) oil-bank formation. INTRODUCTION Most of the scaled model experiments heretofore carried out in the Koninklijke/Shell Laboratorium, Amsterdam, have been done in steel containers, in which oil-saturated sand packs represented the oil-bearing formation. In such experiments, for instance those on the displacement of oil by water, the cumulative oil production was measured as a function of the cumulative water injection. In order to interpret the measured production data, a need has for some time been felt for a means of observing visually what happens in the course of such experiments. Some information of this kind was obtained earlier by observing the water-oil distribution in various cross sections of the sand after the conclusion of the experiment.' However, the technique used did not guarantee that the fluid distribution remained undisturbed. Moreover, the procedure was somewhat elaborate and the information obtained limited. Therefore a new technique has been developed, which is described below. DESCRIPTION OF EXPERIMENTAL TECHNIQUE AND APPARATUS Glass models simulating part of an oil reservoir are filled with ground Pyrex glass of a specific grain size, representing the porous structure of the prototype. Before an experiment is started, the porous formation has to be saturated completely with an oil having exactly the same refractive index as the Pyrex glass powder. All light-scattering surfaces of the glass grains become invisible and the formation is then transparent. If the oil is displaced by another fluid (e.g. by water in a water-drive experiment, or by gas liberated from the oil in a solution gas-drive experiment) the formation becomes opaque in the region where the oil is expelled from the rock.* The back of the apparatus is painted black and illumination is from the front; therefore, in the photographs of the experiments, the oil-bearing formation appears black, whereas the water- or gas-invaded areas are white.

Jan 1, 1958

By Robert Linton

In 1898, Joseph L. Giroux and J. A. Snedaker organized the Pilot Knob Copper Co. and began developing the Pilot Knob mine at Kim-berly, Nev., for high-grade copper ores, carrying good gold and silver values, that the formation had disclosed. At that time the nearest railroad was over 150 mi. distant. The high-grade ores did not prove to be extensive at this point—at least to the depth (240 ft.) to which the work was carried—but development of neighboring claims indicated extensive deposits of sulfide porphyry ore of concentrating grade lying at shallow depth, and deeper deposits of direct-smelting oxidized ores occurring in limestone near the limestone-porphyry contact. The properties passed through the hands of several organizations, with only meager development, until acquired in 1913 by Consolidated Coppermines Co., whose holdings now comprise 3480 acres of mining claims in the Robinson district. Since that time development has been prosecuted more actively; and for the purpose of determining the most efficient and economical method of treating the ores, considerable testing work has been done during the past three years, both in the laboratory and in actual mill operations. At first, the shipments were of ore high enough in grade to be profitable even with the long wagon hauls to the railroad and prevailing freight and smelting charges. In 1905, a blast furnace and a concentrator were erected at Kimberly. On account of insufficient ore supply, the blast furnace was never blown in and later was dismantled. The concentrator as originally equipped was operated for only about two months, both because the ore supply at that time was not sufficient and because gravity concentration did not yield satisfactory extraction. The location and arrangement of the mill further entailed high operating costs. In 1908, the Nevada Consolidated Copper Co. began to mill successfully, on a large scale, its sulfide porphyry ores, which are similar in character to the adjacent Coppermines ores. After that time, all of the ores and concentrates produced by Coppermines Company were smelted and a considerable part of the Coppermines low-grade ores concentrated at the Steptoe works of the Nevada Consolidated Co.

Jan 1, 1921

William P. Blake, TUCSON, Ariz. (communication to the Secretary): As one who in youth, now nearly half a century ago, had the privilege of participating in the initial explorations which have alreacly resulted, within a single lifetime, in the establishment and Development of a vast continental empire, so well described by Dr. Douglas, I may be permitted to supplement with some additional details the comprehensive sketch given in his paper. Before the War Department, in 1853, sent out the Pacific railroad exploring parties, Fremont had already made his memorable expeditions, exploring the Great Basin and the passes into California; Sitgreaves had traversed, from east to west, the Zuni and Moqui country; and, still later, Emory had examined the region along the boundary-line between the United States and Mexico. The services of these pioneers deserve to be mentioned in even an outline of the history of continental development. Concerning the five practicable railroad-routes, suggested in the Reports of Explorations aid Surveys," etc., as published

Jan 1, 1900

By M. T. Simnad, G. Derge, Ling Yang

A method is described for using radioactive tracer for the direct determination of ionic mobility in a molten electrolyte. The ionic mobility of Fe" in silica-saturated iron silicate is found to be 0.0009 (*0.0002) cm2 sec ' volt L at 1250°C. eLECTROCHEMICAL studies', ' of molten iron eE oxide and iron silicates have shown some ionic conductivity at all compositions. The current efficiency in electrolysis increases with the concentration of silica to a maximum of 90 pct at about 34 pet SiO,. In the silica-saturated melts the transport number of ferrous ions is near unity, indicating that

Jan 1, 1957

By J. B. Urnfileb

THE function of gas in the development and production of oil has far reaching consequences that should be emphasized. The technical aspects of the subject have recently had a great deal of attention but less thought has been given to fundamental concepts underlying oil and gas law and the many customs and practices that have grown up in the industry. I shall re- view briefly the advance in knowledge of the subject and attempt to relate these concepts to legislative, judicial and operating problems. Early writers on oil and gas in Pennsylvania noted their close association in oil pools and their contemporaneous decline in output; also, that as gas pressure decreases so does production, that new offset wells reduce the output of existing wells, and even that tubing a well lengthens its flowing life. Expanding gas was deduced as the principal expulsive force. These fundamental observations had been made at least as early as 1880.l They were treated, however, as academic considerations and did not greatly influence law or practice for many years except to instil into all operators an urgent desire to hasten offset drilling to obtain as much of the flush as possible.

Jan 1, 1932

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,' Morozov and Novokharski,' and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By J. J. Tietien, R. O. Clough

A technique previously used to prepare alloys of InAs1-xPx and GaAsl-x Px, miry: the gaseous hydrides arsine and phosphine, has been extended to grow single -crystalline GaAs 1-x Sb x by replacing the phos-phine with stibine. Procedures were developed for handling and storing stibine which now make this chemical useful for vapor phase growth. This represents the first time that this series of alloys has been grown from the vapor phase. Layers of P -type GaSb and GaSb-rich alloys have been grown with the carrier concentrations comparable to the lowest ever reported. In addition, a p-type alloy containing 4 pct GaSb exhibited a mobility of 400 sq cm per v-sec which is equivalent to the highest reported for GaAs. RECENTLY, interest has been shown in the preparation and properties of GaAs1-xSbx alloys, since it was predicted1 that for compositions in the range of 0.1 < x < 0.5, they might provide improved Gunn devices. However, preparation of these alloys presents fundamental difficulties. In the case of liquid phase growth, the large concentration difference between the liquidus and solidus in the phase diagram, at any given temperature, introduces constitutional supercooling problems. It is likely that, for this reason, virtually no description of the preparation of GaAs1-xSbx by this technique has been reported. In the case of vapor phase growth, problems are presented by the low vapor pressure of antimony, and the low melting point of GaSb and many of these alloys. In previous attempts1 at the vapor phase growth of these materials, using antimony pentachloride as the source of antimony vapor, alloy compositions were limited to those containing less than about 2 pct GaSb. This was in part due to the difficulty of avoiding condensation of antimony on introducing it to the growth zone. A growth technique has recently been described2 for the preparation of III-V compounds in which the hydrides of arsenic and phosphorous (AsH3 and pH3) are used as the source of the group V element. With this method, GaAs1-xPx and InAs1-xPx have been prepared2&apos;3 across both alloy series with very good electrical properties. Since the use of stibine (SbH3) affords the potential for effective introduction of antimony to the growth apparatus, in analogy with the other group V hydrides, this growth method has been explored for the preparation of GaAs1-xSbx alloys. In addition to GaSb, these alloys have now been prepared with values of x as high as 0.8. In the case of GaSb, undoped p-type layers were grown with carrier concentrations equivalent to the lowest reported in the literature. Thus it has been demonstrated that, with this growth technique, all of the alloys in this series can be prepared. EXPERIMENTAL PROCEDURE A) Growth Technique. The growth apparatus, shown schematically in Fig. 1, and procedure are virtually identical to that described2 for the growth of GaAs1-xPx alloys, with the exception that phosphine is replaced by stibine.* HCl is introduced over the gallium boat to *Purchased from Matheson Co., E. Rutherford,N+J. transport the gallium predominantly via its subchlo-ride to the reaction zone, where it reacts with arsenic and antimony on the substrate surface to form an alloy layer. The fundamental limiting factors to the growth of GaAs1-xSbx alloys from the vapor phase, especially GaSb-rich alloys, are the low melting point of GaSb (712°C) and the low vapor pressure of antimony at this temperature (<l mm). Thus, relatively low antimony pressures must be employed, which, however, imply low growth rates. To provide low antimony pressures, very dilute concentrations of arsine and stibine in a hydrogen carrier gas were used. Typical flow rates (referred to stp) were about 4 cm3 per min of HC1 (0.06 mole pct)+ from 0.1 to 1 cm3 per min of ASH, (0.002 to 0.02 mole pct), and from 1 to 10 cn13 per min of SbH3 (0.02 to 0.2 mole pct), with a total hydrogen carrier gas flow rate of about 6000 cm3 per min. Although no precise data on decomposition. kinetics exist, it is known4 that stibine decomposes extremely rapidly at elevated temperatures. However, the high linear velocities attendent with the high total flow rate (about 2000 cm per sec) delays cracking of the stibine until it reaches the reaction zone and prevents condensation of antimony in the system. To improve the growth rates of the GaSb-rich alloys, growth temperatures just below the alloy solidus are main-

Jan 1, 1970

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,&apos; the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"&apos; and the

Jan 1, 1946

By James A. Barr

The writer&apos;s first experience with flotation was during World War I, in the bene-ficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added&apos; The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals separation mechanical flotation machines were used in another graphite mill. pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"† using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the phosphate Recovery corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for bene- ficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., sub-,,,tion types, with weir control of pulp between cells. The sand bleeders were very small—about 1¼-in. diameter. As the feed flake. Is to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. 1 and details of the cascade construction in Fig. 2. The cascade installation in plant NO. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1947

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner&apos;s Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe&apos;s gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958

By James A. Barr

The writer&apos;s first experience with flotation was during World War I, in the bene-ficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added&apos; The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals separation mechanical flotation machines were used in another graphite mill. pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"† using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the phosphate Recovery corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for bene- ficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., sub-,,,tion types, with weir control of pulp between cells. The sand bleeders were very small—about 1¼-in. diameter. As the feed flake. Is to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. 1 and details of the cascade construction in Fig. 2. The cascade installation in plant NO. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1947

By L. D. Anderson

WHEN, after years of troublous experiences in roasting sulfide ores with heavy dust and fume losses resulting from the equipment and methods first available, there appeared on the, scene of metallurgy that revolutionary process known as sintering, it was felt that at last there had been found the ideal method for preparing sulfide ores for blast-furnace reduction. Not only were the sulfides roasted but also the fine oxidized ores were bound together with them in strong porous cellular masses which were in the best possible condition for reduction. With the experiences gained in the manipulation of the Huntington-Heberlein, Carmichael-Bradford, and Dwight & Lloyd processes there developed a refinement of detail which brought the whole plan of roasting by sintering to a high plane of perfection. But that metallurgy is never stationary is revealed by the fact that changes in milling practice, particularly the development of flotation, have introduced a new set of problems in sintering itself. Inasmuch as it is felt that these problems have not yet been solved in an entirely satisfactory manner this paper is written to record the present practice of the Salt Lake Valley smelters with the hope that there will be brought forth such discussion as may perhaps lead to still better practice. By far the greater proportion of the sulfides smelted today are flotation concentrates. Usually they are high grade, sometimes as high as 70 per cent. and more in lead. They are extremely fine, many mills grinding the ore so that from 60 to 80 per cent. will pass through screens of 200 mesh. The physical condition in which many of these concentrates reach the smelters is disconcerting to the metallurgists. Some are of about the consistency of putty. Others are of a sticky, slimy nature. Others again, dried to the limit, are veritable powders. Remembering that the down-draft sintering charge for the best results must be porous enough to let air be drawn through it reasonably well, must be thoroughly mixed, and must have some coarse material in it to segregate out and form a layer on the grates, it will be understood that the advent of this extremely fine material has made necessary still further elaboration in the equipment and processes of preparing sulfides for the blast furnaces, all of which is expensive. The high metal contents of the concentrates

Jan 1, 1929

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,&apos; the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"&apos; and the

Jan 1, 1946