Search Documents

By M. B. Willey

The Louisiana Continental Shelf is a submarine area extending offshore as much as one hundred miles. The Gulf bottom in this region varies considerably in extent, profile and composition and consists largely of sedimentary deposits, predominantly those of the Mississippi River. It is very young in a geological sense. Up to the present time few major structures have been erected offshore in the Gulf and no comprehensive preliminary tests have been carried out. Results of pile driving tests are of little value as actual bearing capacities far exceed the dynamic resistance to driving as measured by conventional formulas. Soils encountered are, with few exceptions, cohesive and piling consequently develop their supporting power through surface friction. Because of the time required and relatively high costs, no complete load tests have been made. The results of those tests which have been made, and information obtained from pulling piling in one structure, indicate that design loadings could be considerably increased, and it is contended that comprehensive preliminary investigations including an actual load test, combined with borings and examination of materials encountered by competent soil experts, would effect economies in design far in excess of their cost. The Louisiana Continental Shelf—General The Louisiana . . . continental shelf is a submarine area which extends seaward for as great a distance as one hundred miles off the present shoreline. The Gulf bottom in this region is characterized by low slopes and its outer margin is outlined by the fifty fathom (300 ft.) contour. South of the margin of the shelf the slopes steepen abruptly in the continental slope zone and plunge into the deeps of the Gulf of Mexico.l The engineer who is called upon to design a structure on this shelf is concerned only with the uppermost portion to a depth generally not to exceed Ioo to 150 ft. This layer is very young in a geological sense, and it has the characteristics usually associated with infancy. A few of these are lack of strength, lack of uniformity, and high water content. It consists of the sedimentary deposits of the various rivers and streams entering the Gulf. These streams are all heavily burdened in quantities sufficient to fill the areas at their mouths, were it not for the fact that continual subsidence, equal or greater in amount and acting directly opposite, prevail over the sedimentary workings of the streams. This subsidence has been estimated by geologists to be at the rate of at least one foot per century. Influence of Mississippi River The Mississippi River, which has been the predominant factor in the formation of practically all the Louisiana continental shelf, is one of two rivers flowing into the Gulf that have been able to build protruding deltas. The Mississippi has done so because of its enormous size and load. It deposits sediments in amounts sufficient to replace and actually gain on the amount of subsidence.

Jan 1, 1949

By J. S. Bryner

INTRODUCTION IN the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light microscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silica1,2 replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/3 in. diam 200-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. DESCRIPTION OF METHOD The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper 1 X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1948

By Benjamin N. Webber

During World War II the Pocos de Caldas bauxite deposits of Minas Gerais in Brazil yielded some 60,000 tons. Since then they have maintained a small but almost continuous production. Known for many years, the deposits have been reconnoitered by a number of geologists,1-4 but no dimensional study has been possible because there have not been enough exposures to show clearly the depth, bedrock, and habit of occurrence. The deposits are somewhat unorthodox in their occurrence mainly on steep slopes of mountainous terrain. Although the parent rocks are a sequence of alkalic intrusions that bauxitize readily under the proper conditions, bauxitization has not been the dominant weathering process in the area. It is limited to certain localities where important volumes of bauxite have formed by laterization of several rock types, each yielding a distinctive type of bauxite. Bauxitization may be observed in several stages and in both direct and indirect cycles of formation. The deposits are unique in being of demonstrably recent age, so that the conditions under which the bauxite formed are essentially those of the present time. The bauxitization sequence is postulated in Fig. 1.

Jan 8, 1959

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain.

Jan 4, 1954

Jan 1, 1965

By A. Styka, G. Fischer, S. Tour

Described herein are the results obtained during research work involving coating titanium alloys with molybdenum by vapor-deposition methods. Results show that the method can be used successfully to deposit hard adherent wear-resistant coating of methodmetallic molybdenum on titanium or titanium alloys without changing the microstructure of the titanium base. PRODUCTION and use of titanium and its alloys have increased tremendously in the past few years. The physical, mechanical, and chemical properties of this engineering metal have caused considerable enthusiasm among metallurgists and engineers. However, as with all materials, there are some drawbacks. For example, titanium is susceptible to seizing and galling on wearing surfaces. In order to produce a good wear-resistant surface, many investigations have been conducted evaluating oxidizing, carburizing, nitriding, carbonitriding, sili-conizing, and chromizing of titanium. All of these processes require high temperatures for rather extensive periods of time. It has been possible to produce hard surfaces on titanium and its alloys by a number of these processes at the expense of a deterioration of the physical properties of the base material. A practical solution to the problem of providing titanium and titanium alloy parts with a satisfactory wear-resistant nongalling surface must be one that does not involve excessive temperatures for long periods of time. Sam Tour & Co. Inc. has completed a research and development contract for the United States Army Ordnance Corps on vapor deposition of molybdenum on titanium and titanium alloys. On the basis of results obtained from the research program, titanium alloys can be coated successfully with molybdenum to provide a hard wear-resistant surface without harm to their base mechanical properties. The remainder of this article is a description of the techniques used to apply the coating and the results obtained from wear tests on molybdenum-coated titanium. Theory Basically, the technique used was the application of molybdenum by a vapor-deposition method, thermal decomposition of molybdenum hexacarbonyl [Mo(CO)] with hydrogen as the carrier gas. The selection of this method was based chiefly on the following considerations: 1—low plating temperature which would minimize excessive grain growth, 2— low decomposition temperature of the carbonyl, 3— possibilities of controlling the hardness of the plate by adjusting the carbon content using the plating temperature and pressure as the primary variables, 4—use of high vacuum, thereby avoiding unnecessary oxidation and other complex reactions with the atmosphere. Free energy data1 show the strong tendency for titanium to combine with O2 N2 or carbon from normal temperatures to temperatures above its melting point. To maintain the titanium in a film free condition, the use of as high a vacuum as possible is indicated. The literature' indicates that the reaction product of hydrogen with titanium is unstable in vacuum at around 400°C. 5—Although it is indicated from the thermodynamic standpoint that there is little possibility of removing carbon from either titanium or molybdenum, the work of Lander and Germer -ndicates that the use of a suitable H,/CO ratio is somewhat effective in minimizing carbon deposition. 6—Availability of molybdenum carbonyl. In the simplest form, the conditions of equilibrium3 in chemical reactions involving decomposition of carbonyl are as follows: Mo (CO) ? Mo + 6CO 2CO * C + CO,. The plating rate is proportional to the rate of evolution of CO from the decomposed carbonyl, i.e., it is proportional to the pressure of the gaseous decomposition products. Carbon released from CO gas is the significant constituent for the variability of the physical properties of the product. High carbon deposition is favored by increasing pressure. Limitations are imposed in the selection of plating temperature and pressure. Excessive temperature re-

Jan 1, 1956

By Robin P. Gardner

A radioisotope tracer method combined with a suitable back-calculation method is proposed and evaluated for the determination of model simulation parameters in open-circuit continuous ball mills. The method essentially consists of using impulse and/or step injections of short-lived radioisotopes of the naturally occurring trace elements manganese and sodium. It is evaluated here on the basis of the minimum standard deviations of the product weight-size distributions. These minimum standard deviations are taken as those predicted by a Poisson distribution of the number of particles present in size fractions of the samples taken for analysis. Previously developed tanks-in-series lumped parameter models are used in the evaluation. The results indicate that the method is very promising.

Jan 1, 1976

By B. W. Frazier

AT a recent meeting of the North of England Institute of Mining and Mechanical Engineers, during a discussion upon the compression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

Jan 1, 1874

By R. A. Wyman

The overall approach to nonmetallic mineral flotation practiced in the laboratories of the Mines Branch, Ottawa, Canada, is outlined. The use of floatability tests to indicate possible areas of selectivity is indicated. Selected examples of the evolution of flotation systems are presented. Reagents are briefly discussed.

Jan 1, 1972

By W. A. Longacre

IN the geophysical exploration program of the Cleveland-Cliffs Iron Co. on the Marquette Range of Northern Michigan, the vertical intensity magnetometer has been used to obtain magnetic anomaly maps of large areas. A network of magnetic base stations has been established and the relative vertical intensity at each station measured carefully with respect to a prime base. In the search for the relatively nonmagnetic soft red hematite ore, the magnetic exploration is indirect, involving the study of dikes, faults, contacts, and other structural features. It was found that the, magnetometer, adjusted to a scale value of approximately 40 y per scale division, was satisfactory for this type of exploration, although many magnetic anomalies were encountered that required the use of auxiliary magnets.

Jan 10, 1951

By Dietmar Espig

Very useful general relationships between operating parameters and the operating results for open- and closed-circuit grinding under steady- state conditions are described. The basic idea of the developed methods consists of the introduction of a known reference state. The relations derived from very simple approximations to individual processes allow one to evaluate fineness and mass flow of the desired state after changing the parameters (feed rate, fineness of the feed material, mill length, transport behavior through the mill, classifier characteristics). It was also possible to derive some general relationships, e.g., * an equation for the influence of the operating parameters of the mill on the fineness of the mill output * a criterion to establish if the desired state of a closed grinding circuit is steady state at all * a possibility to substitute the common influence of the transport behavior of the mill and of the classifier by-pass fraction with the coarse stream on the mill outlet product by means of a fictitious worse transport behavior. The applicability of the described methodology to many problems in grinding practice, including questions of controlling grinding circuits, is demonstrated by some examples. In particular, a working diagram of the standard closed grinding circuit has been established.

Jan 1, 1984

By L. C. Campbell

THE purpose of any accident-prevention program is the curtailment or entire elimination of injuries and fatalities. It is a job that is never finished in the coal-mining industry. Day by day, on shift and off shift, men are exposed to injury and death in varying numbers. Seldom is it possible to lock up at the end of the shift and leave a mine plant in the care of a sleepy watchman, as can be done at most manufacturing plants. Even on off shifts there are maintenance and supply crews, coal cutters, pumpers and ventilation men exposed to danger. The prevention program of The Koppers Coal Co. recognizes two primary facts: First, no program can be successful without the full support of the management and complete knowledge of the job at hand on the part of every supervisor. Second, and equally important, is the full cooperation of every employee in observing the safety rules and practices set up by the management. Conscious day-to-day concern for his safety by the indi-vidual worker is the longest stride toward a good safety experience. How to accomplish the education of the individual worker and super-visor for safety is the problem of The Koppers Coal Co. as it is the problem of all coal companies.

Jan 1, 1939

By M. L. Jeremic

Mining practice and underground studies show that, besides mining stresses, lateral tectonic stress also influences roadway stability. Roadways perpendicular to the direction of major lateral stress experience the majority of roof falls, accelerated floor heave, and extrusion of coal ribs into openings. They have the most severe deformations and their maintenance is difficult. Roadways parallel to the major lateral stress exhibit roof sagging and bed separation, moderate though sometimes uneven floor heave, and slabbing of coal ribs into openings. Roadways oblique to lateral stress have, to a certain degree, self-supporting roofs, uniform floor heave, and limited sloughing of coal ribs into openings. The optimal orientation of roadways is, therefore, oblique to the lateral stress direction with fewer crosscuts between them.

Jan 1, 1982

By Eugene Guccione

The domestic iron and steel industry is a vital and major segment of the US economy. Including its employees in coal mining, iron ore mining, limestone quarrying, and related transportation, the industry directly provides jobs for approximately 750,000 people, has a $10 billion annual payroll, and indirectly supports a substantial volume of employment for the entire country. Because of its size and visibility, if nothing else, the US iron and steel industry has always been an easy target of attack and has often been subjected to a great deal of political sound and fury. Today, the industry has different troubles and is fighting for survival: it is faced with spiralling costs, inadequate earnings, labor unrest, foreign competition, government over-regulation, an acute shortage of investment capital, and an all-time high debt burden.

Jan 11, 1975

By Merle L. Bowser, Lawrence W. Scott, John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environmental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of enviornmental monitoring systems is reviewed.

Jan 1, 1980

By E. Gybbon Spilsbury

In the course of the persistent and rapid advance of our country towards the goal she has set for herself, of commercial and manufacturing supremacy, there stand out certain periods or cycles of prosperity or depression, succeeding one another with a comparative regularity as to their ultimate trend, but of varying lengths and intensities. I might compare this course to that of a railroad between two points at different levels, with intervening mountain ranges and valleys, the up-grades climbing towards the final upper terminal of prosperity, while the down-grades retard the ascent, and tend to return to the valleys below. Just at the present time we are evidently at the bottom of one of these valleys, and, before starting to climb the next divide, it may be prudent for us to look into the condition of our rolling-stock, and especially into that of our brakes, and see what the experience of our downward journey has taught us, and whether we are properly equipped for the new upward advance which now lies before us. Probably no previous period of the same duration has produced in all branches of mining and metallurgy improvements SO many and so various as have the last ten or twelve years. Not that they have brought forth any such startling and revo-

Jan 1, 1898

By Stanley D. Michaelson, Ben. H. Slothower

The depletion of most high-grade ore reserves coupled with growing demands for metals and fuels has made it necessary to bring into production increasingly lower grade deposits. Improvements in technology have made lower grade ores economically recoverable in spite of major increases in labor and material costs and the initial investments required to open new mines and build their metallurgical and service plants. To remain competitive, managements of mining companies must keep abreast of and exploit these often complex technical developments. The proper application of these improvements in technology requires extensive and detailed study. In addition, managements of mining and other industries are becoming more deeply involved in public affairs and the myriad of other nontechnical problems common to all industries. These involvements, plus the demands of evaluating technological developments as well as the necessary work related to the routine administration of operations, have required mining managements to delegate additional study and review functions to staff services. To help overcome the problems involved in adopting the best technologies, managements have generally expanded their engineering and research staff services. Integrated, base-metal-producing companies, having open pits, concentrators, smelters, and refineries, are generally more research and engineering oriented than are most smaller mining companies and quarries. However, mining methods for even the simplest open pits and quarries are improving rapidly, and installations of these improvements are essential to combat increasing costs. Because of this, the managements of smaller operations may also require enhanced engineering staff services to realize the potential benefits.

Jan 1, 1968

By J. J. Kramer, W. A. Tiller, G. F. Bolling

The temperatures of solid-liquid interfaces have been measured during the growth of Sn-Pb alloy crystals which exhibited a cellulur substructure. A simple descriptive theory was used in combination with this data and the other measurable growth variables to predict some features of the solute segregation such as the intercell excess concentration and the depth of cell grooves during freezing. The effective distribution coefficient at the tip of a cell, a, was predicted and experimentally found to vary in the range, 1 >a > k0. At the lower limit, the severe segregation that must arise between dendritic cells was substantiated by various observations such as the existence of a second Phase even for alloys of only 0.2 wt pct Pb. ThE cellular morphology of a solid-liquid interface is known to coincide with the formation of a zone of constitutional supercooling ahead of the interface during growth.' The occurrence of various cell structures, (two-dimensional cells, regular cells, dendritic cells), has been quantitatively investigated,'2,4 but the segregation of solute which arises as a consequence of this mode of growth has only been examined qualitatively. An indirect method of obtaining the solute concentration at the tip of a cell cap during solidification has been de-

Jan 1, 1963

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

There is interest in the use of rhenium metal films as resistive elements in thin-film circcits, and already some zvork has been done using er)aporated rhenium films. It has been found that rheniim films protected from the atmosphere by an evaporated layer of silicon monoxide show excellent electrical stability. Unprotected films, however, are subject to aging- effects, notably the increase in electrical resistivity as a function of time. This phenomenon can be understood as primarily one of oxidation of the thin films. This paper is concerned with the study of the oxidation and crystallization behavior of such unprotected films. It has been found that the oxidation rates are a function of the substrate temperatures used during the deposition of Lhe metal films. The strictures observed in the films are correlated with the film resistivities and some data are presented to establish the existence of the various types of oxides of rhenium. ThERE is some interest in the use of thin films of rhenium metal as resistive elements in monolithic, thin-film integrated circuits. Some work has been done using evaporated films and it has been found that such films, if protected from the atmosphere by an evaporated layer of silicon monoxide, show excellent electrical stability up to temperatures of 500"." Rhenium films unprotected from the atmosphere tend to age and the electrical resistivity of the films increases as a function of time. Rhenium films, of the order of <100A thick, prepared by electron-beam evaporation techniques are found to oxidize very readily when exposed to dry air at room temperature. It would seem, therefore, that this aging phenomenon could be attributed to the oxidation of the metal films. In this investigation, the oxidation and crystallization behavior of thin films of rhenium evaporated onto silicon monoxide substrates were studied as a function of the substrate temperatures used during the evaporation. The films were examined using electron-microscopy and electron-diffraction techniques. EXPERIMENTAL RESULTS Rhenium metal was evaporated onto suitable prepared substrates which were heated to various temperatures. The evaporations were performed in a vacuum of approximately 5 x 1CT5 torr. The evaporation was carried out at a rate of approximately 10A per omin. The final film thickness was approximately lOOA and the resistance ranged from 5000 to 10,000 ohms per square. The substrates used for supporting the metal films were made by evaporating 75A of silicon monoxide onto freshly cleaved mica. The silicon monoxide film was then floated off the mica by immersing the composite in water. The film could then be picked up on a clean nickel grid. Silicon monoxide substrates were chosen because of their similarity to quartz and glass substrates commonly used for making thin-film resistors. Fuschillo, Gimpl, and McMas-ter have also shown that silicon monoxide films have only minor structural changes at temperatures up to 800°C. This fact simplified the interpretation of any changes observed in the electron micrographs or electron-diffraction patterns obtained from the deposited rhenium films. After the evaporations were completed, the substrates were cooled to room temperature, except where noted differently, before the coated substrates were removed from the vacuum system. All aging of the deposited films was done in a desiccator. The evaporated films were examined in an electron microscope equipped with a hot stage that would permit continuous observations of the samples up to temperatures of 1000°C. RESULTS A series of electron micrographs of the rhenium films deposited on the silicon monoxide substrates are shown to Figs. 1 to 3. In all cases, the metal films are approximately 100A thick and the micrographs were taken 1 hr after the deposition was completed. here was no apparent structure in the films deposited on the substrates held at the higher temperatures. The

Jan 1, 1967

By Kevin Clermont, William N. Kelley, William E. Bonini, John H. Vreeland

Gravitational field anomalies have been observed over many igneous intrusives of medium (4000 sq km) to small (100 sq km) size in outcrop area. These studies give good results because the residual anomalies can be separated from larger-scale crustal anomalies and density contrasts usually are present. Although unique solutions are not possible, the analysis of the gravity anomalies place important limits on both the areal and depth extent of the intrusive bodies. Of all possible geophysical techniques, gravity studies offer the most promise in the determination of the shape in depth of intrusive bodies.

Jan 1, 1972