Search Documents

By Earl S. Greiner, Eric R. Jette

ALTHOUGH the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data on the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face- centered cubic (gamma) phases, and the alloys containing from 24 to 100 atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt. per cent Si).* The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,5 who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by Osawa and Okamoto.6

Jan 1, 1943

By Charles T. Baroch, Charles J. Baroch

In 20 years of commercial development, nuclear reactors have demonstrated that they are a safe, dependable, and economical source of power. Operating experience with commercial power reactors has firmly established nuclear power as a practicable source of energy. For both boiling-water (BWR) and pressurized-water (PWR) reactors, performances to date have generally met design predictions. Furthermore, it has become possible to analyze and understand the nuclear, chemical, and physical behavior of this class of reactors. The United Kingdom has had similar success with gas-cooled reactors. The Experimental Boiling Water Reactor (EBWR), the first United States experimental power reactor, began operation in 1956. It proved to be capable of supplying 4500 kw (kilowatts) of power. This reactor was followed in 1957 by the Pressurized Water Reactor at Shippingport, Pa. It was the nation's first full-scale central-station nuclear power plant and the first in the world designed exclusively for the production of civilian electric power. The Shippingport reactor was originally designed to produce 60 megawatts (MW) of electricity, and it was increased to 100 MW in 1964. In 12 years of operation, this reactor generated over 4.5-million MW-hr of electricity in spite of many shutdowns for experimental alterations. By 1969, a total of 15 central-station nuclear power reactors were operable in the United States with an aggregate electrical capacity of over 4200 MW. Early in 1964, Jersey Central Power & Light Co. announced plans for constructing a 515-MW nuclear plant at Oyster Creek, N.J., to be built without government financial assistance. The company stated that a nuclear plant had been selected competitively with fossil fuel. Their economic analysis stated that the plant would generate electricity at less than 4 mills per kw-hr, competitive with coal at 200 per million Btu (British thermal units). Coal cost in 1964 for that region averaged 26.00 per million Btu. The Jersey Central report created wide interest in public-utility circles; nevertheless, no other nuclear plants were announced in 1964. However, in 1965, six nuclear plants were announced by utilities, followed by 26 in 1966, 29 in 1967, and 10 in 1968. By Sept. 30, 1969, 97 reactors were operable, being built, or planned. The cost of these, all committed by electric utilities, was estimated at about $12 billion. When constructed, they will have an electrical capacity of 72,000 MW. The unprecedented surge in power reactors that started in 1965 tapered in 1968, and only seven reactors were announced in

Jan 1, 1976

By Kurt Stock

The war caused a demand for enormous quantities of high-grade zinc, which were not available and could not be produced from pure ores in sufficient amounts and in the time required. Redistillation of virgin spelter on a large scale was practiced to supply this demand; this paper gives a full description of the process used by the Oklahoma smelters of the Bartlesville Zinc Co. As the redistillation of zinc has become of historical interest only, having been superseded by the electrolytic process, it was deemed advisable to give expression to this phase of the metallurgy of zinc that, in the past, had never gone beyond laboratory experimentation. THE grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: TOTAL, NOT LEAD, IRON, CADMIUM, OVER. PER PER CENT. PER CENT. PER CENT. CENT. A. High grade 0.07 0.03 0.05 0.10 B. Intermediate 0.20 0.03 0.50 0.50 C. Brass special 0.75 0.04 0.75 1.20 D. Prime western 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages.

Jan 7, 1924

By R. G. Bowman

DISCUSSIONS of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, ii indicates that the .compound possesses characteristics that make it unique among white pigments, and superior to all ;in its particular field. A greater variety of processes have been proposed for manufacturing white lead than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints has been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not-new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the, production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful.

Jan 9, 1925

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By E. Rudy, St. Windisch

The only complete phase diagram investigation of the Ti-W system is by Maykuth and coworkers,&apos; Fig. 1. Although previous work by Gonser2 indicated complete miscibility, later investigations3°5 essentially confirmed the diagram depicted in Fig. 1. The present study was undertaken because preliminary results on metal-rich ternary Ti-W-C alloys indicated complete solid solubility between 0 titanium and tungsten at temperatures above 1300°C—in contradiction to the presently accepted diagram. The powdered elements, as well as crystal bar titanium and tungsten sheet, were used in the preparation of the experimental alloys. The iodide titanium, obtained from Foote Mineral Co., Exton, Pa., had a total impurity content of less than 410 ppm, of which 150 ppm were interstitials (H, O, N, C). The overall purity of the titanium powder (Var-Lac-Oid Chemical Co., New York) was better than 99.7 pct. Major contaminants, in ppm, included: 0, 800; N, 10; H, 1500; Fe + Co + Ni + Cu + Zn, 50; C1, 200. The measured lattice parameters of the titanium were a = 2.94A and c = 4.68,A. The tungsten sheet and the tungsten powder (Wah Chang Corp., Albany, Ore.) contained the following impurities (in ppm, values in parentheses refer to the sheet tungsten): Mo, 50 (70); 0, 140 (110); Fe, 20 (60); Ni, 20 (not determined); N, 110 (not determined); sum of other impurities, <60 (<100). Samples from the iodide titanium bar stock and from tungsten sheet were prepared by repeated melting of the chipped materials in a nonconsumable electrode arc furnace under high-purity helium. The melted alloys were heavily cored, and homogeneity of the alloys could only be achieved after prolonged heat treatments at subsolidus temperatures. The majority of the alloys were therefore prepared by cold compacting the well-mixed powders in steel dies and pre-homogenizing the compacts for 6 hr at 1300°C in a tungsten-element furnace. The vacuum was better than 10"6 Torr, but for additional protection the sample container was wrapped in zirconium foil. Both preparation methods led to identical results. The measurements of the solidus temperatures were carried oat in the Pirani-type furnace described in a previous paper.6 Incipient melting in alloys containing between 20 and 90 at. pct W was rather difficult to detect visually, and therefore a photoelectric transducer system7 was employed to indicate the phase change. For the investigation of the solid-state equilibria, the specimens were first homogenized for 2 hr at slightly subsolidus temperatures in the Pirani fur- nace and then reequilibrated at, and rapidly cooled (-100°C per sec) from, the selected equilibrium temperatures. After the runs, the alloys were analyzed microscopically and by X-ray diffraction. With the exception of spot checks for oxygen and nitrogen in processed alloys, no other chemical analyses were performed. However, as the weight changes of the alloys during processing were within 0.05 pct and the lattice parameters of indeqendently prepared alloy series agreed within 0.0015A, it is reasonable to assume that no significant concentration shifts with respect to the nominal compositions had occurred. The measured solidus temperatures, shown together with literature data in Fig. 2, ascend smoothly from

Jan 1, 1969

By Irvin Lavine

THE discovery of several large deposits of natural sodium sulfate (Glauber salt) in the northwestern part of North Dakota during the summer of 1934 might have been anticipated from a knowledge of the topography and geology of this territory and from the presence of natural C A N A D A FIG. 1.-LOCATIONS OF GLAUBER SALT DEPOSITS, NORTHWESTERN NORTH DAKOTA. North Lake (deposit No. 7) is not shown on this map. It is approximately 13 miles north of Miller Lake (deposit No. 3). sodium sulfate deposits in western Canada, which have been known for several years. In the northwestern part of North Dakota is a chain of shallow lakes, which continues northward into Saskatchewan. Over twenty million tons of Glauber salt has been proved present in these North Dakota deposits. (See Fig. 1.)

Jan 1, 1936

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.&apos; On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

NEW YORK SECTION J. E. JOHNSON, JR., Chairman EDGAR RICKARD, Vice Chairman D. M. LIDDELL, Secretary, 7 Wall St., New York, N. Y. C. A. BOHN, Treasurer JOHN V. N. DORR LEWIS W.. FRANCIS The following minute was unanimously passed at a meeting of the NEW YORK SECTION AMERICAN INSTITUTE OF MINING ENGINEERS held on the evening of June 6, 1917, two regular meetings having been adjourned by unanimous consent until this date out of respect to the memory of the late Chairman of the Section. Minute The death of our beloved fellow member DR. DAVID H. BROWNE one of the foremost metallurgists and one of the most brilliant and original thinkers in the profession of mining engineers, the chairman for the past two years of this section, has caused throughout a wide circle of

Jan 9, 1917

By Garth M. Crosby

Seven mines with important production records in the Coeur d&apos;Alene lie adjacent to the Gem stocks -the Frisco (Gem), Hercules, Interstate, Rex (Sixteen to One), Success (Granite), Sunset, and Tamarack. Old records are incomplete, but avail- able data given in Table I show these mines have produced 10,550,721 tons of ore containing more than 50 million oz of silver, more than 1.5 billion lb of lead, and about 1 billion lb of zinc (approximately 1.25 million tons of lead and zinc combined). Average ore grade is 4.8 oz of silver per ton, 7.2 pct Pb, and 4.6 pct Zn. This impressive production represents about 12 pct of the District&apos;s yield. At present metal prices, with modern beneficiation, the gross value would be more than $400 million.

Jan 7, 1959

By John M. Campbell, W. E. Portman

A series of correlating charts have been prepared to enable the field engineer to predict the amount of stock tank fluid produced by stabilization of first stage separator fluid. The charts shown are particularly convenient for estimating the relative effect of temperature and pressure in economic studies. Further work is planned to investigate the factors affecting stage separation&apos; yo supplement this preliminary work. The direct correlation of separation variables is dictated as a convenience to eliminate the trial and error calculation necessary when using the standard flash vaporization equations. These are obtained by a material balance using the equilibrium vaporization ratio K, and have appeared in the following, or similar. form many times in the literature. where La = mols of any component n in the separator liquid Ko — equilibrium vaporization ratio for any component at separator pressure and temperature Fa = mols of any component n in the feed Vn = mols of any component n in the vapor V = total mols of separator vapor These equations may of course be effectively and accurately solved by use of digital and analog computers. However, these are not usually readily available in field offices and the need often arises for fast results during routine operational problems. Consequently, many methods have been devised in an attempt to simplify the basic calculation.2-14 The methods proposed are generally satisfactory, but do not eliminate trial and error methods and the necessity of subsequent calculations to obtain the answer in volume terms. The purpose of this work. therefore, was to develop accurate charts that would give the result directly in gallons. When using stage separation the recoveries would be lower than those shown, for stabilization usually gives about 95 + per cent recovery on the potential stock tank components in the separator liquid. The recoveries are shown in terms of a 14 psi Reid Vapor Pressure product which has a true vapor pressure of 14.7 psia at 98°F. Consequently, this product represents a stable stock tank liquid under normal storage conditions. To estimate natural gasoline re- coveries by stabilization the volume shown may be multiplied by 1.20 for 18 Ib RVP natural gasoline and 1.36 for 26 lb RVP natural gasoline. PROCEDURE The five analyses shown in Table 1 were chosen since they were representative of wellstream compositions often found and had almost the same propanes plus liquid content, expressed in gallons per 1,000 std. cu ft of wellstream. The distribution of the components though is widely variant. A temperature range of 0-100°F. and a pressure range of 200 to 1,250 psia was chosen inasmuch as most separations fall within these limits The K values used were modified values of those originally published by Katz and Hachmuth.&apos; In the range chosen these have generally given good results when predicting fluid recoveries. The choice was somewhat arbitrary, for the authors&apos; personal experience has shown that

Jan 1, 1957

Nationalization of the coal mining industry in Great Britain was one of the first pieces of major legislation enacted by the post-war Labor Government in 1964. It followed a long period of economic depression with high unemployment and bad industrial relations in the coal mining industry during the 1930&apos;s, and shortages of coal during the last war. Upon nationalization, the National Coal Board took over control of the industry in 1947 and so became the biggest single employer of labor in the western world. As well as the coal mines themselves, it assumed responsibility for a great variety of other assets including coke ovens, byproduct plants, land, houses, railways and shipping wharves.

Jan 6, 1964

By F. S. White, E. L. Kinsella

THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to &apos; quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,1 showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.2 Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a 1/4-in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontally at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 1/2 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4 1/2-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1952

By B. W. Dyer

IN 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KC1) and carnallite (KMgC12.6H20). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. LOCATION AND GEOLOGY OF DEPOSITS The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado Rivera distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 2o E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 2o E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: [Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel]

Jan 1, 1945

By B. W. Dyer

In 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KCl) and carnallite (KMgC12.6H2O). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. Location and Geology of Deposits The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado River— a distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 20 E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 20 E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 1/2 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel

Jan 1, 1948

By B. W. Dyer

In 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KCl) and carnallite (KMgC12.6H2O). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. Location and Geology of Deposits The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado River— a distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 20 E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 20 E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 1/2 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel

Jan 1, 1948

By Hugh Neill, O&apos

In previous papers,&apos; the author has reported the results of experiments on the straining in tension of a single-crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested. The Specimens Employed The principal specimen, A, was prepared for the metallographic examination leading to the determination of the slip planes of the crystal. Therefore the work described in this paper was conducted on metal which had been repeatedly etched and had been allowed to rest for about 30 months after straining. It consisted of a section of the fracture wedge and contiguous unstrained head of the test piece taken along a tetragonal axis parallel to the direction of stressing, the plane of section originally being not far removed from the (011). Several subsequent grindings