Search Documents

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers&apos; vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 9, 1950

By C. P. Besse, N. F. LeBlanc

Described in this paper are oceanographic data which should be considered by an offshore design engineer and methods for developing a design wave height from the oceanographic data. The selection of a design wave is predicated on contemplated waves which might affect the site throughout the life of the structure. Selection of a design wave height may be based on (1) arbitrarily established recurrence Frequencies of hurricanes affecting the structure (predicted wave heights are associated with the expected variations of forces resulting from these waves) and (2) a risk-type evaluation wherein all possible storms affecting the area are considered (anticipated wave heights are associated with both investment plus risk costs and expected variations of forces). It is shown how the following oceanographic predictions are integrated into design considerations: (1) a classification of storm intensity which considers all recorded storms which affected the design area, (2) the recurrence interval of storms of a given- intensity (this interval is dependent on the extent of the geographical area considered in the design problem) and (3) a forecast of all wave heights which might affect the area (geometry of a structure often necessitates consideration of waves from a multiplicity of directions). The authors believe that the described techniques can result in selecting an adequate and reasonable design wave. INTRODUCTION Since the inception of offshore operations in the Gulf of Mexico, engineers engaged in designing suuctural facilities have been plagued with the problem of selecting an adequate and reasonable design wave. In the development of any offshore structure it is mandatory that the engineer evaluate the ability of the structure to withstand the ocean waves to which it will be subjected. Selecting such design waves quite naturally necessitates a coalition of the oceanographer and the design engineer. The oceanographer must provide a detailed knowledge of scientific principles which govern the behavior of waters in the Gulf of Mexico. He should also have an adequate knowledge of the manner in which design waves are utilized by the engineer. Although the design engineer&apos;s primary responsibility is applying the oceanographer&apos;s specialized knowledge in the creation of real structures, it is important that he possess some knowledge of related oceanographic principles to reasonably evaluate and apply the recommendations of the oceanographer. In the Gulf of Mexico it is the hurricane wind waves which generally govern the design of an offshore facility. The oceanographer must therefore develop techniques for predicting the heights, periods and frequency of all hurricane waves which might affect a particular structure. From this mass of oceanographic data, the design engineer must select the design waves which will apply to his particular design. PAST STUDIES ON FREQUENCY AND AMPLITUDE OF HURRICANE WIND WAVES Past oceanographic studies on the frequency of hurricane wave heights in the Gulf of Mexico have been devoted largely to predicting the recurrence interval of hurricanes which will generate maximum significant waves of given heights. The maximum significant wave height is the average height of the highest one third of the waves in that portion of the storm producing maximum wave heights. Since these waves occur over a relatively small portion of the storm (Fig. 1) and since the paths of hurricanes vary considerably (Fig. 2), the recurrence frequency of such heights is largely a function of the extent of the geographical area considered. In establishing the frequency of maximum significant waves for the entire American Gulf coast, the major fully developed hurricanes which affected the coastline from BrOwnsville, Tex., to Key West, Fla., were considered (Fig. 2). These Storms were selected and described by C. L-

By B. J. Scheiner, A. G. Smelley

The Bureau of Mines, US Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. Infield tests, phosphate clay waste has been dewatered from a nominal 2.5% solids to greater than 20% solids. In other field tests, coal-clay waste has been dewatered from a nominal 3% solids to greater than 55% solids. In addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12% solids to 40% solids.

Jan 1, 1985

By Ole Singstad

The legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer. After preliminary investigation it was decided to build the tunnel from Canal St., New York, to 12th St., Jersey City, which is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels—one for west-bound traffic and one for east-bound—the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear head room of 13 ft. 6 in. The tunnels have an exterior diameter of 29 ft. 6 in. The interior lining is of concrete, the sidewalls, tiled with a vitreous white tile, and the roadways are paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. Basis of Ventilation It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character. There have been vehicular tunnels built in Europe, principally in London, but they are shorter and have a smaller traffic capacity. Up to the present time, at least, they have handled a very large percentage of horsedrawn vehicles so that the necessary ventilation has been provided for by the natural draft through the portals and open shafts. Within the last few years, however, a small mechanical ventilating plant has been installed in the Blackwall Tunnel, which has been in operation about 27 years. I might mention that at the time this work was started, it was considered by many that the problem of ventilation was insuperable and it

Jan 1, 1927

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proa[n]o hill are the Fresnillo mines, and it is marked now by a great gash cut by gloryhole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo. which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notable active in 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under Garcia&apos;s energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1833 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de benefacio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

By R. M. Porter

The Sullivan mine of Consolidated Mining and Smelting Co. of Canada Ltd. is located one mile west of Kimberley. With its daily production of 10,000 tons, the mine is the largest in British Columbia and one of the outstanding mines of the world. The Sullivan orebody dips from nearly horizontal to 45". The ore zone is a bedded replacement de- posit in argillite with a width varying from a few inches up to 300 ft. The main sulfide minerals are pyrrhotite, pyrite, galena, and sphalerite. The chief metals produced are lead and zinc, with less important qualities of iron, silver, tin, antimony, bismuth, cadmium, indium and sulfur.

Jan 12, 1963

By Sir James Kitson

By the courtesy of the President and Council of the American Institute of Mining Engineers, I have been invited to take the chair and open the proceedings of this congress. It is a graceful compliment to those members of the Iron and Steel Institute who are your honored guests at this moment—an acknowledgment of high consid-

Jan 1, 1891

By R. A. Vik, C. B. Daellenbach, W. M. Mahan

The influence of reduction roasting and thermal shock on the grindability of a refractory low-grade Michigan iron ore was examined in bench-scale tests. The quantitative effects of the various treatments were evaluated at three sieve levels, 48, 100, and 400 mesh, with ball-mill-grindability and work-index parameters as response indicators. Data from the testing program were statistically analyzed to isolate the effects of cooling rate, roasting temperature, mesh level, and ore chemical condition. All four variables were found to have an important influence on the grindability of the treated ore. Ore chemical condition and roasting temperature had the most pronounced effects.

Jan 1, 1972

By M. E. True, B. L. Stone

To cope with the problems encountered when drilling at greater depths and to reduce the amount of physical effort required on the part of drilling crews in making round trips, a new type of semiautomatic power-operated drilling machinery has been developed which permits round trips to be made without the drill pipe being touched by hand. This equipment consists of hy-draulically operated tongs which perform the stabbing, spinning, and tong-ing operations, and two power-operated racking units mounted in the derrick for carrying the pipe to and from the center of the hole and positioning it on the mat and in the rack. With this equipment all of the operations of the various units are controlled remotely by manipulation of hydraulic valve levers and electric switches. INTRODUCTION As horsepower rises to meet the demand for deeper drilling, it is necessary to increase the weight of surface drilling equipment. Also, the duration of repetitive operations in making round trips to change bits is greatly increased with depth. Harder formations encountered at greater depths reduce bit life rapidly, resulting in more frequent round trips and in some instances more time is consumed in changing bits than in drilling. Since the introduction of the first rotary employed to drill for oil in 18951, there has been relatively little change in the general procedure for making up, breaking out, stabbing, and racking drill pipe in making round trips to change bits. The conventional method of making round trips with the drill pipe requires that drilling crews lend strenuous physical assistance to manually operated tools. Although many new devices have been developed to improve efficiency, increase speed of making round trips, improve safety, and reduce the amount of physical effort required in handling drill pipe, it is considered a vital necessity to substitute automatic or semiautomatic power-operated machinery for many of our more or less manual operations if extremely deep drilling is to be carried out successfully on a production basis in the same manner as our shallower drilling of today. Field tests have been made of remotely controlled power-operated tongs, spinner, stabber, and racking equipment. The tongs, which include a built-in pipe spinner, are mounted on a column, are capable of gripping and supporting the weight of a 90-foot stand of drill pipe, and are provided with means for moving the pipe vertically as well as to and from the center of the hole. The racking equipment consists of two units, one at the level of the conventional monkey board and the other at the first girth on the ladder side of the derrick. Most of the physical effort of making round trips with drill pipe has been eliminated in that all of the operations of tonging, spinning, stabbing, and racking of pipe on the floor are controlled by an operator in a seated position by manipulation of hydraulic and electric valve levers and buttons. The driller is relieved of operating the cathead, leaving only the hoisting and slips to be controlled. Complete round trips are made without the drill pipe being touched by the drilling crews. Although the speed of pulling or running a single stand with the power-operated equipment is approximately the same as that with conventional equipment, it is possible to maintain this rate for long periods, whereas fatigue slows crews working conventionally during round trips, especially under adverse weather. After completing round trips with this equipment, drilling crews are not exhausted, consequently, are able to perform effectively their duties while drilling, which is essential for maximum over-all efficiency. Safety is substantially improved as the derrickman performs his duties from a platform enclosed by rails and the tong lines and spinning chain are eliminated from the derrick floor. The hazards encountered in racking drill pipe on the floor and in stabbing are also eliminated. Figure 1 shows a drawing of a derrick equipped with the power-operated drill&apos;pipe handling equipment.

Jan 1, 1949

By J. W. Axelson, J. N. S. Kwong, J. T. Adams, E. L. Pire, J. F. Johnson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental understanding of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1—the mechanism of the fracture process itself, 2— the particle size distribution of the crushed product, and 3—the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced. Fracture of Solids This phase of the crushing problem is the most fundamental because it is concerned with the actual mechanism of fracture. The main problems in a study of the fracture process are concerned with the questions of why and how fracture occurs and why there is such a discrepancy between the actual and theoretical energies needed in a fracture process. In considering the how of fracture, Poncelet40 carried Out experiments On the crushing of glass under compression. Actual photographs were taken of the glass plates in various stages of fracture-From these experiments Poncelet was able to postulate a probable mechanism of fracture. Probably because of the quantitative nature of the problem, considerable effort has been expended to find an explanation for the low tensile strength of materials and the conversely high energy for crushing. Tensile strengths are often only 1/500 of the theoretical while the energy for crushing is usually at least 500 times the theoretical. A review of the work to explain the low strength of glass is given by Weyl,52 in which the work of Griffith," Joffe,32 and Powell and Preston " are discussed. In a recent paper Seitz46 holds that the presence of flaws and fissures, as originally expounded by Griffith, is the most probable reason for the low strength of metals. Since a mass of data has been accumulated on the fracture strength of materials, several investigators have attempted to correlate this data in the form of an equation. Glathart and Preston," Taylor,40 Ponce-let,40 Machlin and Norwich," and Frederickson and Eyring,20 have all considered this problem, and the final relationship has always been that the stress for fracture is proportional to the logarithm of time. Murgatroyd30 arrived at a very similar relationship by a different method. The study of the fracture process has used many methods. Among some of these are the thermody-namic approach used by Furth21 which was based on the work of BornxL and later used by Saibel,43 and the statistical method applied by Fisher and Hollo-mon.10 In recent years metallurgists have concerned themselves with the problem of brittle .fracture as opposed to the usual plastic failure of metals. The great amount of interest shown is reflected by the number of contributors to the recent symposium on the fracture of metals.&apos; Repeated failures of welded ships during World War II have accelerated these Studies.31,50,34 The shifting of thought from an emphasis on the

Jan 1, 1952

By M. E. True, B. L. Stone

To cope with the problems encountered when drilling at greater depths and to reduce the amount of physical effort required on the part of drilling crews in making round trips, a new type of semiautomatic power-operated drilling machinery has been developed which permits round trips to be made without the drill pipe being touched by hand. This equipment consists of hy-draulically operated tongs which perform the stabbing, spinning, and tong-ing operations, and two power-operated racking units mounted in the derrick for carrying the pipe to and from the center of the hole and positioning it on the mat and in the rack. With this equipment all of the operations of the various units are controlled remotely by manipulation of hydraulic valve levers and electric switches. INTRODUCTION As horsepower rises to meet the demand for deeper drilling, it is necessary to increase the weight of surface drilling equipment. Also, the duration of repetitive operations in making round trips to change bits is greatly increased with depth. Harder formations encountered at greater depths reduce bit life rapidly, resulting in more frequent round trips and in some instances more time is consumed in changing bits than in drilling. Since the introduction of the first rotary employed to drill for oil in 18951, there has been relatively little change in the general procedure for making up, breaking out, stabbing, and racking drill pipe in making round trips to change bits. The conventional method of making round trips with the drill pipe requires that drilling crews lend strenuous physical assistance to manually operated tools. Although many new devices have been developed to improve efficiency, increase speed of making round trips, improve safety, and reduce the amount of physical effort required in handling drill pipe, it is considered a vital necessity to substitute automatic or semiautomatic power-operated machinery for many of our more or less manual operations if extremely deep drilling is to be carried out successfully on a production basis in the same manner as our shallower drilling of today. Field tests have been made of remotely controlled power-operated tongs, spinner, stabber, and racking equipment. The tongs, which include a built-in pipe spinner, are mounted on a column, are capable of gripping and supporting the weight of a 90-foot stand of drill pipe, and are provided with means for moving the pipe vertically as well as to and from the center of the hole. The racking equipment consists of two units, one at the level of the conventional monkey board and the other at the first girth on the ladder side of the derrick. Most of the physical effort of making round trips with drill pipe has been eliminated in that all of the operations of tonging, spinning, stabbing, and racking of pipe on the floor are controlled by an operator in a seated position by manipulation of hydraulic and electric valve levers and buttons. The driller is relieved of operating the cathead, leaving only the hoisting and slips to be controlled. Complete round trips are made without the drill pipe being touched by the drilling crews. Although the speed of pulling or running a single stand with the power-operated equipment is approximately the same as that with conventional equipment, it is possible to maintain this rate for long periods, whereas fatigue slows crews working conventionally during round trips, especially under adverse weather. After completing round trips with this equipment, drilling crews are not exhausted, consequently, are able to perform effectively their duties while drilling, which is essential for maximum over-all efficiency. Safety is substantially improved as the derrickman performs his duties from a platform enclosed by rails and the tong lines and spinning chain are eliminated from the derrick floor. The hazards encountered in racking drill pipe on the floor and in stabbing are also eliminated. Figure 1 shows a drawing of a derrick equipped with the power-operated drill&apos;pipe handling equipment.

Jan 1, 1949

By Wolfgang O. Gluschke

INTRODUCTION Virtually all countries have general legislation covering most aspects of mining and mineral processing, including investment and tax laws, safety and health regulation, and specific rules applying to exploration reporting procedures. Yet most developing countries negotiate individual agreements with foreign investors for major mineral projects, in particular when all or part of the expected output is exported. Such agreements are known under several different names, as for example concession agreement; technical assistance agreement or service contract; management agreement; production sharing contract; joint venture; or contract of work. The objectives and conditions governing such contracts are as diverse as these titles are. While a mining project is only one among a large mumber of similar undertakings in industrial countries, in most developing countries such projects usually have a dominating position within the country&apos;s economy. The general legislation is often inadequate and insufficiently detailed to cover all aspects of large projects with extensive foreign inputs and international markets. Therefore, the need for specific arrangements. Specific arrangements may also become necessary due to the complexity of markets for mineral products, the large number of participants - equity partners, suppliers, financial institutions, buyers, etc. - or economic and political conditions in the host country and fiscal regulations in the home country of the investors. Most agreements are concluded between governments, or government agencies, in developing countries and private industry headquartered in developed market economies - Canada and the United States of America in North America, Western European countries, Japan, South Africa and Australia - or, in some instances, with state-owned firms in these countries. There are fewer agreements between developing countries and the centrally planned economy countries - Eastern Europe and the USSR - which cannot be considered here because of absence of adequate information. Agreements can be concluded at any of the different stages from exploration through closing of a mine. While most contracts are negotiated at the time when a potentially viable ore body has been delineated and investigated sufficiently to anticipate a realistic time for commencement of production, other agreements start with "grass-roots" exploration, during operation of a mine, smelter or refinery or, exceptionally, after a temporary shutdown. While several major provisions are included in all types of agreements, others are covered in much more detail (or not at all) in some contracts reflecting the specific work programme of each project. While it is realized that subdivision and classification of complex contractual relations is necessarily arbitrary to a certain extent, such grouping is useful in practical terms, especially for the non-specialist. The following discussion, therefore, will start with a description of the major forms of contractual relation - concession, investment contract, joint venture, management agreement, service and production sharing contracts. Major issues covered in all, or almost all, agreements will then be dealt with. These include stages of development, corporate structure and control, fiscal arrangements, infrastructure development and environmental law, and dispute settlement and renegotiation. FORMS OF CONTRACT RELATIONS There has been marked change in the type of agreement entered into during the 1960s (and before) and the early 1970s and the period thereafter. While straight "concessions" - granting of exclusive rights to foreign investors over a certain deposit or areas with little restriction or well-defined obligations - were the rule during the first half of this century, more complex agreements have evolved since. Some of these cover every conceivable aspect, foreseen or only possible, and define rights and obligations of all partners to the last detail. Over the years, agreements have without doubt become more beneficial for the developing host countries, in part as a result of well-publicized nationalizations, as for example in Chile, and in part due to changed attitudes in all countries

Jan 1, 1985

By Bruce Vandre

Jan 1, 1985

By P. E. Palmer, A. H. Daane, C. E. Habermann

Jan 1, 1965

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.&apos; The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.&apos; The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By S. G. Valentine

Blast-furnace blowing engines are broadly of two main types: either steam - or gas-driven reciprocating engines, or turbine-driven rotary engines.

Jan 1, 1915

By Howard N. Evanenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. AVERAGE RECOVERY The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered-it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal-is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1946