Search Documents

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947

By H. Kosmider, P. Coheur

New processes of blowing with an oxygen-enriched air or gas mixtures of oxygen and steam allow the steelmaker to produce, in a basic converter, a rimmed steel low in nitrogen (0.0020 pct), phosphorous (0.020 pct), and sulphur (0.020 pct). The physical properties (ductility) of the new steels are excellent. Furthermore, from the point of view of economy, these new methods of blowing offer outstanding possibilities. THE natural occurrence of geological deposits of iron ore and local economic circumstances led European blast furnace men to work large quantities of lean iron ore with a phosphorus content as high as 0.5 pct. The iron obtained from these ores generally contains 1.5 to 2.1 pct phosphorus, 3.6 to 3.9 pct carbon, 0.3 to 0.6 pct silicon, 0.04 to 0.08 pct sulphur, and 0.3 to 1.2 pct manganese. To produce steel from this pig iron, the steelmaker has at his disposal several processes. One of the simplest and most economical is the pneumatic process developed by S. G. Thomas in 1879. This process of steelmaking, called the Thomas process, consists of blowing through the bottom of a basic bessemer converter and is used widely in Western Europe, as shown in Table I. Due to the development of tonnage oxygen plants, this process has become more important because the use of oxygen offers new possibilities of steel manufacture. Not only may the quality of the steel be improved, but liquid pig iron also may be used, the composition of which does not meet the heat requirements of the blow with atmospheric air. It is not intended to present here a detailed scientific discussion of the basic bessemer process but rather to discuss briefly its industrial possibilities in the case of rimmed steel and when blowing with atmospheric air, oxygen-enriched air, or gas mixtures of oxygen and steam. This paper is based on the current practice at Klockner-Hüttenwerk Haspe's steel division, and at six Belgian and Luxemburg steel works. The latter are members of the Liege section of the C.N.R.M. (National Institute for Metallurgical Research) and are: ARBED, John Cocker-ill, Esperance-Longdoz, HADIR, Miniere et Metal-lurgique de Rodange, and Ougree-Marihaye, most of which are working with tonnage oxygen plants.' In order to avoid any misunderstanding, it should be noted that most of the techniques to be men- tioned, or similar ones, are used currently at many steel plants in Western Europe. Background The basic converters used in Europe have a capacity of 17 to 65 tons of steel, and are similar in shape to the one in Fig. 1. The lining is brick or rammed dolomite and has a life of 250 to 500 blows. The bottom is rammed dolomite and has a life of 40 to 80 blows. As far as we know, the type of blast used does not appear to have any influence on the life of the lining. Bottom life, on the contrary, depends very much upon the composition of the blast. It is only when

Jan 1, 1955

By J. P. Newell, R. W. Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By G. W. Josephson

SINCE the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,1 and the large-scale expansion of the industry has taken place since 1900. HISTORICAL BACKGROUND Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a Nigh degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun's rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof-conservatively, 500 per cent. Slate Granules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate pro-

Jan 1, 1944

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By Seymour Fiekowsky, Alvin Kaufman

Taxes are compulsory charges levied by a government for its support. They are usually paid to support the general services provided by government rather than special services (such as safety inspection). The latter are normally supported by user charges often called license fees. Taxes are used by national governments not only to raise money but also as a part of fiscal policy. As such, taxes are used to stimulate or deflate the economy, as an incentive to save or invest, as a means of allocating national resources, and as a means of redistributing income. In our discussion, we will deal only with those facets of the subject that relate specifically to the mineral industry. In doing so we will deal with taxes levied on all industry in a generalized way and only insofar as it affects our industry, but at some length on those portions of the tax system related directly to the mineral industry. It is not our intent to provide a "cookbook" for computing taxes, but rather to present some of the policy issues that bedevil those who must develop our tax policies. MINERAL TAXES The mineral industry is subject to the full range of taxes levied by governments. These include taxes on income, property, and sales, as well as excise and severance taxes. The latter are somewhat similar to a royalty in , that such taxes are levied either ad valorem or per unit of output. Severance taxes most commonly are charged to oil and gas output, although coal, salt, sulfur, and iron ore production also have been taxed in this manner. The major governmental advantage of the severance tax is the administrative ease of collection. On the other hand, it poses an addition to cost independent of profitability. As a consequence, the severance tax can cause premature abandonment if mineral product prices do not rise sufficiently to cover it. Such a rise may not occur if differential tax rates are levied by the various states. Property taxes normally are levied on all property owners, including mineral owners. The major difficulties in this kind of tax, in so far as mining is concerned, are erratic valuation coupled to the inherent problems involved in assessing a property where the extent and richness is chiefly unknown. The impact of these taxes, including state income taxes, is reduced somewhat, as they are usually deductible from gross income as a business expense with a consequent lowering of national income taxes. The net cost of severance, property, sales, and state or local

Jan 1, 1976

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

ALABAMA Anniston.-Carrington, F. G. Auburn.-Brown, R. L. Battelle.-Green, G. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Bonnyman, J. Bowron, J. Bush, M. W. Crawford, G. G. Crockard, F. H. Ellis, E. E. Fairbairn, C. T. Gallacher, J. Geismer, H. S.

Jan 1, 1917

With the exception of the mentions of coal in Illinois in the period 1660-1680, already referred to, the first coal found in the United States was in the James River, Virginia, field. In 1699 a large tract of .land above the present city of Richmond was allotted for a settlement of French Huguenots by the colonial, government, near the present Manakin, about fourteen miles above Richmond. They soon found coal, tradition says it was uncovered by a hunter pulling out a small tree in a. steel) bank near a stream, and Colonel William Byrd, F.R.S., the most prominent man of his day in the colony, wrote to the Colonial Council of Virginia, May 10 and 11, 1701: "The 10th of May, last., I with Coll. Randolph, Capt. Epes, Capt. Webb, &c., went up to the new settlements of ye French Refugees at ye Manaken Town.... We went tip to ye Cole, w'ch is not above a mile and a half from their settlement on the great upper Creeke, w'ch, riseing very high in great Raines hath washed away the Banks that the Coal lyes bare, otherwise it's very deep in the Earth, the land being very high, and near the surface is plenty of Slate.", Some of the Frenchmen were evidently familiar with the use of coal, as on May 22, 1702, "David Menestrier a black smith and one of ye french Refugees Inhabiting at Luciana Petitioning his Excellency that he may have leave to use ye coal mines lately discovered there for his forge his Excellency by and with ye advice of ye Council loth hereby give Leave to ye said David Menestrier to take what coales he shall want. out of ye said Coal mine for ye use of his forge according to ye Prayer of ye said Petition."2 There was some uncertainty about the grant of these lands to the Huguenots which caused the request for leave to use this coal, as a Virginia patent in its usual form allowed the owner to mine all minerals excepting gold and silver, which were subject to royalties for the Crown. After the visit to the coal above mentioned, "Wm. Byrd, understanding the land had not been granted to the French, took out a patent for 344 acres, including the same, (the coal) which patent was dated October 20, 1704".3

Jan 1, 1942

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By W. J. Reagan

Many factors enter into the manufacture of basic open-hearth steel of high quality. Perhaps the two most important are temperature and the iron oxide content of the metal. If we can control these two factors we can essentially control basic open-hearth practice. SOURCE AND EFFECT OF IRON OXIDE Earlier investigators, especially Herty and his associates, have shown that iron oxide is introduced into the open-hearth furnace in four ways:' 1. By oxidation of the scrap by furnace gases. 2. By decomposition of the limestone. 3. By oxidation of the iron oxide in the slag by furnace gases. 4. By direct addition of iron ore to the charge. We also know that the speed of operation of an open-hearth furnace depends, for a given charge and given combustion conditions, on the rate at which iron oxide will diffuse from the slag into the metal. The rate of diffusion depends upon a number of variables, such as iron oxide content of the slag, slag viscosity, etc., which also depend upon the amount of iron oxide in the metal, amount of carbon present, temperature, and so forth. For a given carbon and a given temperature, the iron oxide content of the metal is in proportion to the iron oxide content of the slag. This fact can be easily verified by analysis of slag samples taken as described by Herty.2 It is preferable to take these samples just before deoxidetion. In killing the steel samples with aluminum it is desirable to use aluminum rod of 99 per cent purity; ordinary commercial aluminum rod with a purity of approximately 92 per cent is not satisfactory. In drilling these samples it is also essential to take the largest amount of drillings possible. This gives more accurate results because it eliminates spotty segregation of A12O3.

Jan 1, 1932

By H. W. Camp

Research is defined, scientifically, as a "systematic investigation of some phenomenon, and also a search for hidden treasures." Chemists tell us that the hidden treasures of petroleum are far richer than the products which have been best known to us. However, these secrets will be discovered only through intensive and systematic, as well as scientific, industrial research. Indeed, the scope of the subject is so great that such an intensive research program should be assumed by a centralized organization supported by the petroleum industry as a whole. Such organization should assume the responsibilities for investigation of new products and development of markets for such products. Gasoline, the chief product of the petroleum industry has become a cheap commodity. The continual uncontrolled overproduction of crude petroleum, the intensive competitive condition in the marketing of petroleum products and the increase of refining efficiency and installing of cracking facilities, have all combined to lower the market value of gasoline. The purchaser has profited from the lower cost of gasoline by way of lower prices so that today the most important product can scarcely be manufactured at a profit. In other fields, manufacturing industries have diversified their products when faced by a similar situation. Thus, they have been able to widen their marketing outlook. Why cannot the petroleum industry employ the same tactics? Right now we are hearing much discussion concerning the development of a wider market for existing petroleum products and new products for existing or prospective markets. For instance, we can cite recent developments for use of propane, butane and ethylene. Butane has been found to be an efficient and inexpensive refrigerant, especially adapted to home refrigerating systems. Propane and butane fractions of natural gasoline may be shipped under pressure and may be used as a substitute for, acetylene in cutting torches in connection with oxygen. There is a possibility of substituting butane for gas oil in the carburation of coal gas, as we know that butane contains practically the gas enrichment as the same volume of gas oil and should prove to be a superior product for

Jan 1, 1928

By M. Schussler, J. S. Brunhouse

Arc-melted and electron-beam melted tantalum in the cold-worked and the recrystallized conditions showed high strength, good tensile ductility, and excellent notch toughness down to 321°F. Arc-melted material, containing moderate amounts of interstitials, possessed better short-time strength than higher purity electron-beam melted material up to 2000°F. Cold-working substantially strengthened arc-melted tantalum, whereas electron-beam melted material exhibited a low work-hardening rate and possessed better formability characteristics. With identical compositions and microstructures, the mechanical properties of melted tantalum and uacuum-sintered tantalum should be similar. TANTALUM metal usage is increasing rapidly in a number of applications. The outstanding chemical corrosion resistance of tantalum accounts for its applications in chemical processing equipment for severe service conditions and for surgical uses in the medical field. The largest present requirements for tantalum are in the electronics industry, where its special properties are useful in capacitors. The high melting point (5425°F) and inherent ductility of tantalum also suggest that tantalum and tantalum-base alloys might offer an excellent combination of high strength at very high temperatures and good fabri-cability. Pure tantalum has been used in significant amounts in parts requiring high-temperature strength, such as heating elements, reflectors, and heat shields in high-vacuum high-temperature furnaces and in electronic tubes. A few very promising tantalum-base alloys have been developed and are being investigated extensively. The possibilities for tantalum as a high-temperature structural material, either unalloyed or alloyed, will become better defined when more extensive mechanical property data are known. pughl measured the tensile properties of vacuum-sintered tantalum in sheet form for the temperature range of 78" to 1500°K (-321' to 2240°F), and Bechtold reported data obtained at low temperatures.' Drennen3 determined creep and stress-rupture properties of both vacuum-sintered and arc-melted tantalum sheet at 1200 °F. Some additional data on the mechanical properties of tantalum at temperatures up to 5000 °F have been summarized elsewhere.4'5 It is probable that large structural shapes of tantalum, either unalloyed or alloyed, can most readily be produced from ingots prepared by melting. Consequently, the present investigation was undertaken to determine more extensive short-time mechanical properties of tantalum metal consolidated by melting. EXPERIMENTAL PROCEDURE Melting and Fabrication—Two tantalum ingots were utilized in this study to obtain information on the effect of interstitial elements on mechanical properties. Both ingots were melted from Union Carbide Metals Co. tantalum dendrites.

Jan 1, 1961

By W. B. Phillips

The earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in " Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. ***** The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would be thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.' In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114, Township 6, contains 79.08 grains of free sillphuric acid per gallon. This locality is about 13 miles (21 km.) south . of Delaware Creek and about 35 miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos. Texas is in the Pirst Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 1, 1918

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By W. M. Courtis

This district commences near Pigeon River, the northeastern boundary between Minnesota and Province of Ontario, and extends entirely around the north shore of Lake Superior, terminating for the present at the Bruce Mines on Lake Huron. The discoveries of mineral-bearing veins have been confined for the most part to the lake shore, or to the country opened up by the Dawson Red River road. As yet the country back from the lake has been but little explored, on account of its roughness, being intersected by steep, rocky trap bluffs, 1000 or more feet high, and alternating white cedar and tamarack swamps. The forests are exceedingly difficult for prospectors. In many places Titanic piles of rocks, protected by chevaux-de-frise of dead cedars, with their hooked, tough, sharp branches, and a covering of spongy moss, sometimes several feet thick, successively guard against the discovery of hidden treasure. The Hudson's Bay Company for nearly a century have maintained trading-posts at Fort William and other points, which probably opened the way to the first discoveries that were made at Prince's Bay, near the western limit of the district. At this point a large vein was worked by Colonel Prince, the owner, as early as 1846. The richest part of the vein seems to have been on Spar Island, but work was stopped on account of excess of water. Sir William Logan states that a mass of ore weighing several hundred pounds and carrying 3 per cent. of silver was taken out. On the mainland small quantities of native and sulphide of silver were found, together with iron and copper pyrites, zinc blende, and galena, in a large spar vein. On the main shore a drift 165 feet long and 90 feet in depth

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935